init
This commit is contained in:
273
printer.cfg
Normal file
273
printer.cfg
Normal file
@@ -0,0 +1,273 @@
|
||||
# Pin Mappings for Stock 2023 Creality Ender 3 V3 SE
|
||||
#
|
||||
# To use this configuration:
|
||||
# 1. During "make menuconfig", select:
|
||||
# - STM32F103 with a "28KiB bootloader"
|
||||
# - Serial communication on USART1 (PA10/PA9)
|
||||
#
|
||||
# 2. For a direct serial connection:
|
||||
# - In "make menuconfig", select:
|
||||
# - "Enable extra low-level configuration options"
|
||||
# - Serial communication on USART3 (PB11/PB10)
|
||||
# - This is accessible via the 10-pin IDC cable used for the LCD module:
|
||||
# - Pin 3: Tx
|
||||
# - Pin 4: Rx
|
||||
# - Pin 9: GND
|
||||
# - Pin 10: VCC
|
||||
#
|
||||
# 3. Build the firmware by running:
|
||||
# - make
|
||||
#
|
||||
# 4. Flash the firmware:
|
||||
# - Copy "klipper/out/klipper.bin" to an SD card.
|
||||
# - Insert the SD card into the printer and power it on.
|
||||
# - Ensure the firmware filename ends in ".bin" and is different from the last flashed filename.
|
||||
#
|
||||
# For further details, refer to https://www.klipper3d.org/Config_Reference.html.
|
||||
|
||||
#####################################################################
|
||||
# Include the relevant configuration depending on what you are using.
|
||||
#####################################################################
|
||||
|
||||
[include mainsail.cfg]
|
||||
|
||||
[include macros.cfg]
|
||||
|
||||
[include timelapse.cfg]
|
||||
|
||||
[mcu]
|
||||
#####################################################################
|
||||
# Obtain definition by "ls -l /dev/serial/by-id/"
|
||||
#####################################################################
|
||||
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
|
||||
restart_method: command
|
||||
|
||||
[filament_switch_sensor filament_sensor]
|
||||
switch_pin: ^PC15
|
||||
pause_on_runout: true
|
||||
|
||||
[temperature_sensor mcu_temp]
|
||||
sensor_type: temperature_mcu
|
||||
min_temp: 0
|
||||
max_temp: 100
|
||||
|
||||
[printer]
|
||||
kinematics: cartesian
|
||||
max_velocity: 250
|
||||
max_accel: 2500
|
||||
minimum_cruise_ratio: 0.5
|
||||
square_corner_velocity: 5.0
|
||||
max_z_velocity: 100
|
||||
max_z_accel: 500
|
||||
|
||||
#####################################################################
|
||||
# X/Y Stepper Settings
|
||||
#####################################################################
|
||||
|
||||
[stepper_x]
|
||||
step_pin: PC2
|
||||
dir_pin: !PB9
|
||||
enable_pin: !PC3
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: !PA5
|
||||
position_endstop: -6
|
||||
position_min: -6
|
||||
position_max: 230
|
||||
homing_speed: 60
|
||||
|
||||
[tmc2209 stepper_x]
|
||||
uart_pin: PB12
|
||||
run_current: 0.6
|
||||
sense_resistor: 0.150
|
||||
stealthchop_threshold: 0
|
||||
interpolate: True
|
||||
|
||||
[stepper_y]
|
||||
step_pin: PB8
|
||||
dir_pin: PB7
|
||||
enable_pin: !PC3
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: !PA6
|
||||
position_endstop: -14
|
||||
position_min: -14
|
||||
position_max: 225
|
||||
homing_speed: 60
|
||||
|
||||
[tmc2209 stepper_y]
|
||||
uart_pin: PB13
|
||||
run_current: 0.6
|
||||
sense_resistor: 0.150
|
||||
stealthchop_threshold: 0
|
||||
interpolate: True
|
||||
|
||||
[force_move]
|
||||
enable_force_move: True
|
||||
|
||||
#####################################################################
|
||||
# Z Stepper Settings
|
||||
#####################################################################
|
||||
|
||||
[stepper_z]
|
||||
step_pin: PB6
|
||||
dir_pin: !PB5
|
||||
enable_pin: !PC3
|
||||
microsteps: 16
|
||||
rotation_distance: 8
|
||||
endstop_pin: probe:z_virtual_endstop
|
||||
position_min: -3
|
||||
position_max: 250
|
||||
homing_speed: 5
|
||||
second_homing_speed: 1
|
||||
homing_retract_dist: 2.5
|
||||
|
||||
[tmc2209 stepper_z]
|
||||
uart_pin: PB14
|
||||
run_current: 0.8
|
||||
sense_resistor: 0.150
|
||||
stealthchop_threshold: 0
|
||||
interpolate: True
|
||||
|
||||
#####################################################################
|
||||
# Extruder
|
||||
#####################################################################
|
||||
|
||||
[extruder]
|
||||
step_pin: PB4
|
||||
dir_pin: PB3
|
||||
enable_pin: !PC3
|
||||
microsteps: 16
|
||||
rotation_distance: 7.3403877
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.750
|
||||
max_extrude_cross_section: 5
|
||||
max_extrude_only_distance: 500
|
||||
pressure_advance: 0.04
|
||||
heater_pin: PA1
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PC5
|
||||
#control: pid
|
||||
# Tuned for stock hardware with a target of 200 degrees Celsius.
|
||||
#pid_Kp: 27.142
|
||||
#pid_Ki: 1.371
|
||||
#pid_Kd: 134.351
|
||||
min_temp: 0
|
||||
max_temp: 260
|
||||
|
||||
#####################################################################
|
||||
# Bed Heater
|
||||
#####################################################################
|
||||
|
||||
[heater_bed]
|
||||
heater_pin: PB2
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PC4
|
||||
#control: pid
|
||||
# Tuned for stock hardware with a target of 70 degrees Celsius.
|
||||
#pid_kp: 66.371
|
||||
#pid_ki: 0.846
|
||||
#pid_kd: 1301.702
|
||||
min_temp: 0
|
||||
max_temp: 100
|
||||
|
||||
#####################################################################
|
||||
# Bed Mesh & BL Touch
|
||||
#####################################################################
|
||||
|
||||
[bed_mesh]
|
||||
speed: 150
|
||||
mesh_min: 10,10
|
||||
mesh_max: 206,210.5
|
||||
probe_count: 7, 7
|
||||
algorithm: bicubic
|
||||
|
||||
[bltouch]
|
||||
sensor_pin: ^PC14
|
||||
control_pin: PC13
|
||||
x_offset: -24.0
|
||||
y_offset: -14.5
|
||||
#z_offset: 0.1
|
||||
speed: 20
|
||||
pin_move_time: 0.4
|
||||
stow_on_each_sample: False
|
||||
probe_with_touch_mode: True
|
||||
|
||||
#####################################################################
|
||||
# Fan Control
|
||||
#####################################################################
|
||||
|
||||
[heater_fan hotend_fan]
|
||||
pin: PC1
|
||||
|
||||
[fan]
|
||||
pin: PA0
|
||||
|
||||
#####################################################################
|
||||
# Idle Timeout & Homing
|
||||
#####################################################################
|
||||
|
||||
[idle_timeout]
|
||||
gcode:
|
||||
OFF
|
||||
timeout: 600
|
||||
|
||||
[safe_z_home]
|
||||
home_xy_position: 139, 127
|
||||
speed: 60
|
||||
z_hop: 10
|
||||
z_hop_speed: 5
|
||||
|
||||
#####################################################################
|
||||
# Beeper
|
||||
#####################################################################
|
||||
|
||||
[output_pin beeper]
|
||||
pin: PB0
|
||||
|
||||
#####################################################################
|
||||
# G-Code features
|
||||
#####################################################################
|
||||
|
||||
[gcode_arcs]
|
||||
|
||||
[exclude_object]
|
||||
|
||||
#*# <---------------------- SAVE_CONFIG ---------------------->
|
||||
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
||||
#*#
|
||||
#*# [bltouch]
|
||||
#*# z_offset = 1.510
|
||||
#*#
|
||||
#*# [bed_mesh default]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.222500, -0.060000, -0.092500, -0.065000, -0.027500, -0.002500, 0.010000
|
||||
#*# 0.150000, -0.077500, -0.155000, -0.105000, -0.052500, 0.002500, -0.025000
|
||||
#*# 0.187500, -0.085000, -0.157500, -0.120000, -0.100000, -0.042500, -0.057500
|
||||
#*# 0.062500, -0.087500, -0.140000, -0.130000, -0.112500, -0.097500, -0.090000
|
||||
#*# 0.007500, -0.077500, -0.150000, -0.122500, -0.112500, -0.105000, -0.097500
|
||||
#*# 0.142500, -0.007500, -0.095000, -0.102500, -0.102500, -0.082500, -0.080000
|
||||
#*# 0.305000, 0.275000, 0.040000, 0.022500, 0.007500, -0.002500, 0.020000
|
||||
#*# x_count = 7
|
||||
#*# y_count = 7
|
||||
#*# mesh_x_pps = 2
|
||||
#*# mesh_y_pps = 2
|
||||
#*# algo = bicubic
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 10.0
|
||||
#*# max_x = 205.95999999999998
|
||||
#*# min_y = 10.0
|
||||
#*# max_y = 210.45999999999998
|
||||
#*#
|
||||
#*# [extruder]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 28.332
|
||||
#*# pid_ki = 1.536
|
||||
#*# pid_kd = 130.682
|
||||
#*#
|
||||
#*# [heater_bed]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 67.201
|
||||
#*# pid_ki = 0.976
|
||||
#*# pid_kd = 1156.696
|
||||
Reference in New Issue
Block a user