Changed thermistor

.moonraker.conf.bkp

@@ -74,5 +74,9 @@ restart_delay = 3
 bound_services = 
 	klipper
 
+[spoolman]
+server = https://spoolman.fieryeagle.org/
+sync_rate = 5
+
 [timelapse]
 

moonraker.conf

@@ -76,6 +76,10 @@ restart_delay: 3
 bound_services:
     klipper
 
+[spoolman]
+server: https://spoolman.fieryeagle.org/
+sync_rate: 5
+
 [timelapse]
 ##   Following basic configuration is default to most images and don't need
 ##   to be changed in most scenarios. Only uncomment and change it if your

printer.cfg

@@ -153,7 +153,7 @@ sensor_pin: PC5
 #pid_Ki: 1.371
 #pid_Kd: 134.351
 min_temp: 0
-max_temp: 265
+max_temp: 320
 
 #####################################################################
 #   Bed Heater
@@ -177,8 +177,8 @@ max_temp: 100
 
 [bed_mesh]
 speed: 150
-mesh_min: 10,10
-mesh_max: 206,210.5
+mesh_min: 32,32
+mesh_max: 174,178.5
 probe_count: 7, 7
 algorithm: bicubic
 
@@ -237,34 +237,34 @@ pin: PB0
 #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
 #*#
 #*# [bltouch]
-#*# z_offset = 1.540
+#*# z_offset = 1.775
 #*#
 #*# [bed_mesh default]
 #*# version = 1
 #*# points =
-#*# 	0.222500, -0.060000, -0.092500, -0.065000, -0.027500, -0.002500, 0.010000
-#*# 	0.150000, -0.077500, -0.155000, -0.105000, -0.052500, 0.002500, -0.025000
-#*# 	0.187500, -0.085000, -0.157500, -0.120000, -0.100000, -0.042500, -0.057500
-#*# 	0.062500, -0.087500, -0.140000, -0.130000, -0.112500, -0.097500, -0.090000
-#*# 	0.007500, -0.077500, -0.150000, -0.122500, -0.112500, -0.105000, -0.097500
-#*# 	0.142500, -0.007500, -0.095000, -0.102500, -0.102500, -0.082500, -0.080000
-#*# 	0.305000, 0.275000, 0.040000, 0.022500, 0.007500, -0.002500, 0.020000
+#*# 	0.072500, 0.060000, 0.032500, 0.020000, 0.005000, -0.010000, -0.012500
+#*# 	0.045000, 0.045000, 0.002500, -0.032500, -0.035000, -0.070000, -0.072500
+#*# 	0.037500, 0.002500, -0.025000, -0.050000, -0.070000, -0.105000, -0.097500
+#*# 	0.012500, -0.030000, -0.070000, -0.067500, -0.080000, -0.122500, -0.115000
+#*# 	0.005000, -0.032500, -0.077500, -0.075000, -0.070000, -0.132500, -0.120000
+#*# 	0.030000, -0.020000, -0.060000, -0.067500, -0.070000, -0.122500, -0.117500
+#*# 	0.052500, 0.020000, -0.060000, -0.060000, -0.047500, -0.102500, -0.050000
 #*# x_count = 7
 #*# y_count = 7
 #*# mesh_x_pps = 2
 #*# mesh_y_pps = 2
 #*# algo = bicubic
 #*# tension = 0.2
-#*# min_x = 10.0
-#*# max_x = 205.95999999999998
-#*# min_y = 10.0
-#*# max_y = 210.45999999999998
+#*# min_x = 32.0
+#*# max_x = 173.96
+#*# min_y = 32.0
+#*# max_y = 178.45999999999998
 #*#
 #*# [extruder]
 #*# control = pid
-#*# pid_kp = 28.332
-#*# pid_ki = 1.536
-#*# pid_kd = 130.682
+#*# pid_kp = 18.083
+#*# pid_ki = 0.843
+#*# pid_kd = 96.972
 #*#
 #*# [heater_bed]
 #*# control = pid