274 lines
6.5 KiB
INI
274 lines
6.5 KiB
INI
# Pin Mappings for Stock 2023 Creality Ender 3 V3 SE
|
|
#
|
|
# To use this configuration:
|
|
# 1. During "make menuconfig", select:
|
|
# - STM32F103 with a "28KiB bootloader"
|
|
# - Serial communication on USART1 (PA10/PA9)
|
|
#
|
|
# 2. For a direct serial connection:
|
|
# - In "make menuconfig", select:
|
|
# - "Enable extra low-level configuration options"
|
|
# - Serial communication on USART3 (PB11/PB10)
|
|
# - This is accessible via the 10-pin IDC cable used for the LCD module:
|
|
# - Pin 3: Tx
|
|
# - Pin 4: Rx
|
|
# - Pin 9: GND
|
|
# - Pin 10: VCC
|
|
#
|
|
# 3. Build the firmware by running:
|
|
# - make
|
|
#
|
|
# 4. Flash the firmware:
|
|
# - Copy "klipper/out/klipper.bin" to an SD card.
|
|
# - Insert the SD card into the printer and power it on.
|
|
# - Ensure the firmware filename ends in ".bin" and is different from the last flashed filename.
|
|
#
|
|
# For further details, refer to https://www.klipper3d.org/Config_Reference.html.
|
|
|
|
#####################################################################
|
|
# Include the relevant configuration depending on what you are using.
|
|
#####################################################################
|
|
|
|
[include mainsail.cfg]
|
|
|
|
[include macros.cfg]
|
|
|
|
[include timelapse.cfg]
|
|
|
|
[mcu]
|
|
#####################################################################
|
|
# Obtain definition by "ls -l /dev/serial/by-id/"
|
|
#####################################################################
|
|
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
|
|
restart_method: command
|
|
|
|
[filament_switch_sensor filament_sensor]
|
|
switch_pin: ^PC15
|
|
pause_on_runout: true
|
|
|
|
[temperature_sensor mcu_temp]
|
|
sensor_type: temperature_mcu
|
|
min_temp: 0
|
|
max_temp: 100
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 250
|
|
max_accel: 2500
|
|
minimum_cruise_ratio: 0.5
|
|
square_corner_velocity: 5.0
|
|
max_z_velocity: 100
|
|
max_z_accel: 500
|
|
|
|
#####################################################################
|
|
# X/Y Stepper Settings
|
|
#####################################################################
|
|
|
|
[stepper_x]
|
|
step_pin: PC2
|
|
dir_pin: !PB9
|
|
enable_pin: !PC3
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
endstop_pin: !PA5
|
|
position_endstop: -6
|
|
position_min: -6
|
|
position_max: 230
|
|
homing_speed: 60
|
|
|
|
[tmc2209 stepper_x]
|
|
uart_pin: PB12
|
|
run_current: 0.6
|
|
sense_resistor: 0.150
|
|
stealthchop_threshold: 0
|
|
interpolate: True
|
|
|
|
[stepper_y]
|
|
step_pin: PB8
|
|
dir_pin: PB7
|
|
enable_pin: !PC3
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
endstop_pin: !PA6
|
|
position_endstop: -14
|
|
position_min: -14
|
|
position_max: 225
|
|
homing_speed: 60
|
|
|
|
[tmc2209 stepper_y]
|
|
uart_pin: PB13
|
|
run_current: 0.6
|
|
sense_resistor: 0.150
|
|
stealthchop_threshold: 0
|
|
interpolate: True
|
|
|
|
[force_move]
|
|
enable_force_move: True
|
|
|
|
#####################################################################
|
|
# Z Stepper Settings
|
|
#####################################################################
|
|
|
|
[stepper_z]
|
|
step_pin: PB6
|
|
dir_pin: !PB5
|
|
enable_pin: !PC3
|
|
microsteps: 16
|
|
rotation_distance: 8
|
|
endstop_pin: probe:z_virtual_endstop
|
|
position_min: -3
|
|
position_max: 250
|
|
homing_speed: 5
|
|
second_homing_speed: 1
|
|
homing_retract_dist: 2.5
|
|
|
|
[tmc2209 stepper_z]
|
|
uart_pin: PB14
|
|
run_current: 0.8
|
|
sense_resistor: 0.150
|
|
stealthchop_threshold: 0
|
|
interpolate: True
|
|
|
|
#####################################################################
|
|
# Extruder
|
|
#####################################################################
|
|
|
|
[extruder]
|
|
step_pin: PB4
|
|
dir_pin: PB3
|
|
enable_pin: !PC3
|
|
microsteps: 16
|
|
rotation_distance: 7.3403877
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
max_extrude_cross_section: 5
|
|
max_extrude_only_distance: 500
|
|
pressure_advance: 0.04
|
|
heater_pin: PA1
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PC5
|
|
#control: pid
|
|
# Tuned for stock hardware with a target of 200 degrees Celsius.
|
|
#pid_Kp: 27.142
|
|
#pid_Ki: 1.371
|
|
#pid_Kd: 134.351
|
|
min_temp: 0
|
|
max_temp: 260
|
|
|
|
#####################################################################
|
|
# Bed Heater
|
|
#####################################################################
|
|
|
|
[heater_bed]
|
|
heater_pin: PB2
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PC4
|
|
#control: pid
|
|
# Tuned for stock hardware with a target of 70 degrees Celsius.
|
|
#pid_kp: 66.371
|
|
#pid_ki: 0.846
|
|
#pid_kd: 1301.702
|
|
min_temp: 0
|
|
max_temp: 100
|
|
|
|
#####################################################################
|
|
# Bed Mesh & BL Touch
|
|
#####################################################################
|
|
|
|
[bed_mesh]
|
|
speed: 150
|
|
mesh_min: 10,10
|
|
mesh_max: 206,210.5
|
|
probe_count: 7, 7
|
|
algorithm: bicubic
|
|
|
|
[bltouch]
|
|
sensor_pin: ^PC14
|
|
control_pin: PC13
|
|
x_offset: -24.0
|
|
y_offset: -14.5
|
|
#z_offset: 0.1
|
|
speed: 20
|
|
pin_move_time: 0.4
|
|
stow_on_each_sample: False
|
|
probe_with_touch_mode: True
|
|
|
|
#####################################################################
|
|
# Fan Control
|
|
#####################################################################
|
|
|
|
[heater_fan hotend_fan]
|
|
pin: PC1
|
|
|
|
[fan]
|
|
pin: PA0
|
|
|
|
#####################################################################
|
|
# Idle Timeout & Homing
|
|
#####################################################################
|
|
|
|
[idle_timeout]
|
|
gcode:
|
|
OFF
|
|
timeout: 600
|
|
|
|
[safe_z_home]
|
|
home_xy_position: 139, 127
|
|
speed: 60
|
|
z_hop: 10
|
|
z_hop_speed: 5
|
|
|
|
#####################################################################
|
|
# Beeper
|
|
#####################################################################
|
|
|
|
[output_pin beeper]
|
|
pin: PB0
|
|
|
|
#####################################################################
|
|
# G-Code features
|
|
#####################################################################
|
|
|
|
[gcode_arcs]
|
|
|
|
[exclude_object]
|
|
|
|
#*# <---------------------- SAVE_CONFIG ---------------------->
|
|
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
|
#*#
|
|
#*# [bltouch]
|
|
#*# z_offset = 1.510
|
|
#*#
|
|
#*# [bed_mesh default]
|
|
#*# version = 1
|
|
#*# points =
|
|
#*# 0.222500, -0.060000, -0.092500, -0.065000, -0.027500, -0.002500, 0.010000
|
|
#*# 0.150000, -0.077500, -0.155000, -0.105000, -0.052500, 0.002500, -0.025000
|
|
#*# 0.187500, -0.085000, -0.157500, -0.120000, -0.100000, -0.042500, -0.057500
|
|
#*# 0.062500, -0.087500, -0.140000, -0.130000, -0.112500, -0.097500, -0.090000
|
|
#*# 0.007500, -0.077500, -0.150000, -0.122500, -0.112500, -0.105000, -0.097500
|
|
#*# 0.142500, -0.007500, -0.095000, -0.102500, -0.102500, -0.082500, -0.080000
|
|
#*# 0.305000, 0.275000, 0.040000, 0.022500, 0.007500, -0.002500, 0.020000
|
|
#*# x_count = 7
|
|
#*# y_count = 7
|
|
#*# mesh_x_pps = 2
|
|
#*# mesh_y_pps = 2
|
|
#*# algo = bicubic
|
|
#*# tension = 0.2
|
|
#*# min_x = 10.0
|
|
#*# max_x = 205.95999999999998
|
|
#*# min_y = 10.0
|
|
#*# max_y = 210.45999999999998
|
|
#*#
|
|
#*# [extruder]
|
|
#*# control = pid
|
|
#*# pid_kp = 28.332
|
|
#*# pid_ki = 1.536
|
|
#*# pid_kd = 130.682
|
|
#*#
|
|
#*# [heater_bed]
|
|
#*# control = pid
|
|
#*# pid_kp = 67.201
|
|
#*# pid_ki = 0.976
|
|
#*# pid_kd = 1156.696
|