Added check for event pressed to clear space cadet (#5839)

* Added check for pressed to clear space cadet

* Found some docs to update

* Update docs/quantum_keycodes.md

Co-Authored-By: fauxpark <fauxpark@gmail.com>

* Changes from PR

Vagrantfile

@@ -7,6 +7,8 @@ Vagrant.configure(2) do |config|
 
   # VMware/Virtualbox ( and also Hyperv/Parallels) 64 bit
   config.vm.box = "generic/debian9"
+  
+  config.vm.synced_folder '.', '/vagrant'
 
   # This section allows you to customize the Virtualbox VM
   # settings, ie showing the GUI or upping the memory
@@ -64,7 +66,7 @@ Vagrant.configure(2) do |config|
   # If this causes issues you can run a 'vagrant destroy' and then
   # add a # before ,run: (or change "always" to "once") and run 'vagrant up' to get a working
   # non-updated box and then attempt to troubleshoot or open a Github issue
-  config.vm.provision "shell", inline: "/bin/sh -c 'yes | /vagrant/util/qmk_install.sh'", run: "always"
+  config.vm.provision "shell", inline: "/vagrant/util/qmk_install.sh", run: "always"
 
   config.vm.post_up_message = <<-EOT
 

docs/feature_rgb_matrix.md

@@ -30,9 +30,11 @@ Configure the hardware via your `config.h`:
 #define DRIVER_COUNT 2
 #define DRIVER_1_LED_TOTAL 25
 #define DRIVER_2_LED_TOTAL 24
-#define DRIVER_LED_TOTAL DRIVER_1_LED_TOTAL + DRIVER_2_LED_TOTAL
+#define DRIVER_LED_TOTAL (DRIVER_1_LED_TOTAL + DRIVER_2_LED_TOTAL)
 ```
 
+!> Note the parentheses, this is so when `DRIVER_LED_TOTAL` is used in code and expanded, the values are added together before any additional math is applied to them. As an example, `rand() % (DRIVER_1_LED_TOTAL + DRIVER_2_LED_TOTAL)` will give very different results than `rand() % DRIVER_1_LED_TOTAL + DRIVER_2_LED_TOTAL`.
+
 Currently only 2 drivers are supported, but it would be trivial to support all 4 combinations.
 
 Define these arrays listing all the LEDs in your `<keyboard>.c`:
@@ -195,6 +197,8 @@ enum rgb_matrix_effects {
     RGB_MATRIX_CYCLE_ALL,           // Full keyboard solid hue cycling through full gradient
     RGB_MATRIX_CYCLE_LEFT_RIGHT,    // Full gradient scrolling left to right
     RGB_MATRIX_CYCLE_UP_DOWN,       // Full gradient scrolling top to bottom
+    RGB_MATRIX_CYCLE_OUT_IN,        // Full gradient scrolling out to in
+    RGB_MATRIX_CYCLE_OUT_IN_DUAL,   // Full dual gradients scrolling out to in
     RGB_MATRIX_RAINBOW_MOVING_CHEVRON,  // Full gradent Chevron shapped scrolling left to right
     RGB_MATRIX_DUAL_BEACON,         // Full gradient spinning around center of keyboard
     RGB_MATRIX_RAINBOW_BEACON,      // Full tighter gradient spinning around center of keyboard
@@ -234,6 +238,8 @@ You can disable a single effect by defining `DISABLE_[EFFECT_NAME]` in your `con
 |`#define DISABLE_RGB_MATRIX_CYCLE_ALL`                 |Disables `RGB_MATRIX_CYCLE_ALL`                |
 |`#define DISABLE_RGB_MATRIX_CYCLE_LEFT_RIGHT`          |Disables `RGB_MATRIX_CYCLE_LEFT_RIGHT`         |
 |`#define DISABLE_RGB_MATRIX_CYCLE_UP_DOWN`             |Disables `RGB_MATRIX_CYCLE_UP_DOWN`            |
+|`#define DISABLE_RGB_MATRIX_CYCLE_OUT_IN`              |Disables `RGB_MATRIX_CYCLE_OUT_IN`             |
+|`#define DISABLE_RGB_MATRIX_CYCLE_OUT_IN_DUAL`         |Disables `RGB_MATRIX_CYCLE_OUT_IN_DUAL`        |
 |`#define DISABLE_RGB_MATRIX_RAINBOW_MOVING_CHEVRON`    |Disables `RGB_MATRIX_RAINBOW_MOVING_CHEVRON`   |
 |`#define DISABLE_RGB_MATRIX_DUAL_BEACON`               |Disables `RGB_MATRIX_DUAL_BEACON`              |
 |`#define DISABLE_RGB_MATRIX_RAINBOW_BEACON`            |Disables `RGB_MATRIX_RAINBOW_BEACON`           |

docs/feature_rgblight.md

@@ -37,9 +37,9 @@ QMK uses [Hue, Saturation, and Value](https://en.wikipedia.org/wiki/HSL_and_HSV)
 
 <img src="gitbook/images/color-wheel.svg" alt="HSV Color Wheel" width="250"/>
 
-Changing the **Hue** cycles around the circle.  
-Changing the **Saturation** moves between the inner and outer sections of the wheel, affecting the intensity of the color.  
-Changing the **Value** sets the overall brightness.
+Changing the **Hue** cycles around the circle.<br>
+Changing the **Saturation** moves between the inner and outer sections of the wheel, affecting the intensity of the color.<br>
+Changing the **Value** sets the overall brightness.<br>
 
 ## Keycodes
 
@@ -77,8 +77,7 @@ Your RGB lighting can be configured by placing these `#define`s in your `config.
 |`RGBLIGHT_SLEEP`     |*Not defined*|If defined, the RGB lighting will be switched off when the host goes to sleep|
 |`RGBLIGHT_SPLIT`     |*Not defined*|If defined, synchronization functionality for split keyboards is added|
 
-## Animations
-
+## Effects and Animations
 
 Not only can this lighting be whatever color you want,
 if `RGBLIGHT_EFFECT_xxxx` or `RGBLIGHT_ANIMATIONS` is defined, you also have a number of animation modes at your disposal:
@@ -100,29 +99,54 @@ Check out [this video](https://youtube.com/watch?v=VKrpPAHlisY) for a demonstrat
 
 Note: For versions older than 0.6.117, The mode numbers were written directly. In `quantum/rgblight.h` there is a contrast table between the old mode number and the current symbol.
 
-The following options can be used to tweak the various animations:
+### Effect and Animation Toggles
+
+Use these defines to add or remove animations from the firmware. When you are running low on flash space, it can be helpful to disable animations you are not using.
+
+|Define                              |Default      |Description                                                                          |
+|------------------------------------|-------------|-------------------------------------------------------------------------------------|
+|`RGBLIGHT_ANIMATIONS`               |*Not defined*|Enable all additional animation modes.                                   |
+|`RGBLIGHT_EFFECT_ALTERNATING`       |*Not defined*|Enable alternating animation mode.                                       |
+|`RGBLIGHT_EFFECT_BREATHING`         |*Not defined*|Enable breathing animation mode.                                         |
+|`RGBLIGHT_EFFECT_CHRISTMAS`         |*Not defined*|Enable christmas animation mode.                                         |
+|`RGBLIGHT_EFFECT_KNIGHT`            |*Not defined*|Enable knight animation mode.                                            |
+|`RGBLIGHT_EFFECT_RAINBOW_MOOD`      |*Not defined*|Enable rainbow mood animation mode.                                      |
+|`RGBLIGHT_EFFECT_RAINBOW_SWIRL`     |*Not defined*|Enable rainbow swirl animation mode.                                     |
+|`RGBLIGHT_EFFECT_RGB_TEST`          |*Not defined*|Enable RGB test animation mode.                                          |
+|`RGBLIGHT_EFFECT_SNAKE`             |*Not defined*|Enable snake animation mode.                                             |
+|`RGBLIGHT_EFFECT_STATIC_GRADIENT`   |*Not defined*|Enable static gradient mode.                                             |
+
+### Effect and Animation Settings
+
+The following options are used to tweak the various animations:
 
 |Define                              |Default      |Description                                                                          |
 |------------------------------------|-------------|-------------------------------------------------------------------------------------|
-|`RGBLIGHT_EFFECT_BREATHING`         |*Not defined*|If defined, enable breathing animation mode.                                         |
-|`RGBLIGHT_EFFECT_RAINBOW_MOOD`      |*Not defined*|If defined, enable rainbow mood animation mode.                                      |
-|`RGBLIGHT_EFFECT_RAINBOW_SWIRL`     |*Not defined*|If defined, enable rainbow swirl animation mode.                                     |
-|`RGBLIGHT_EFFECT_SNAKE`             |*Not defined*|If defined, enable snake animation mode.                                             |
-|`RGBLIGHT_EFFECT_KNIGHT`            |*Not defined*|If defined, enable knight animation mode.                                            |
-|`RGBLIGHT_EFFECT_CHRISTMAS`         |*Not defined*|If defined, enable christmas animation mode.                                         |
-|`RGBLIGHT_EFFECT_STATIC_GRADIENT`   |*Not defined*|If defined, enable static gradient mode.                                             |
-|`RGBLIGHT_EFFECT_RGB_TEST`          |*Not defined*|If defined, enable RGB test animation mode.                                          |
-|`RGBLIGHT_EFFECT_ALTERNATING`       |*Not defined*|If defined, enable alternating animation mode.                                       |
-|`RGBLIGHT_ANIMATIONS`               |*Not defined*|If defined, enables all additional animation modes                                   |
 |`RGBLIGHT_EFFECT_BREATHE_CENTER`    |*Not defined*|If defined, used to calculate the curve for the breathing animation. Valid values are 1.0 to 2.7 |
 |`RGBLIGHT_EFFECT_BREATHE_MAX`       |`255`        |The maximum brightness for the breathing mode. Valid values are 1 to 255             |
-|`RGBLIGHT_EFFECT_SNAKE_LENGTH`      |`4`          |The number of LEDs to light up for the "Snake" animation                             |
-|`RGBLIGHT_EFFECT_KNIGHT_LENGTH`     |`3`          |The number of LEDs to light up for the "Knight" animation                            |
-|`RGBLIGHT_EFFECT_KNIGHT_OFFSET`     |`0`          |The number of LEDs to start the "Knight" animation from the start of the strip by    |
-|`RGBLIGHT_EFFECT_KNIGHT_LED_NUM`    |`RGBLED_NUM` |The number of LEDs to have the "Knight" animation travel                             |
 |`RGBLIGHT_EFFECT_CHRISTMAS_INTERVAL`|`1000`       |How long to wait between light changes for the "Christmas" animation, in milliseconds|
 |`RGBLIGHT_EFFECT_CHRISTMAS_STEP`    |`2`          |The number of LEDs to group the red/green colors by for the "Christmas" animation    |
+|`RGBLIGHT_EFFECT_KNIGHT_LED_NUM`    |`RGBLED_NUM` |The number of LEDs to have the "Knight" animation travel                             |
+|`RGBLIGHT_EFFECT_KNIGHT_LENGTH`     |`3`          |The number of LEDs to light up for the "Knight" animation                            |
+|`RGBLIGHT_EFFECT_KNIGHT_OFFSET`     |`0`          |The number of LEDs to start the "Knight" animation from the start of the strip by    |
 |`RGBLIGHT_RAINBOW_SWIRL_RANGE`      |`360`        |Range adjustment for the rainbow swirl effect to get different swirls                |
+|`RGBLIGHT_EFFECT_SNAKE_LENGTH`      |`4`          |The number of LEDs to light up for the "Snake" animation                             |
+
+### Example Usage to Reduce Memory Footprint
+  1. Remove `RGBLIGHT_ANIMATIONS` from `config.h`.
+  1. Selectively add the animations you want to enable. The following would enable two animations and save about 4KiB:
+
+```diff
+ #undef RGBLED_NUM
+-#define RGBLIGHT_ANIMATIONS
++#define RGBLIGHT_EFFECT_STATIC_GRADIENT
++#define RGBLIGHT_EFFECT_RAINBOW_SWIRL
+ #define RGBLED_NUM 12
+ #define RGBLIGHT_HUE_STEP 8
+ #define RGBLIGHT_SAT_STEP 8
+```
+
+### Animation Speed
 
 You can also modify the speeds that the different modes animate at:
 

docs/feature_space_cadet.md

@@ -20,7 +20,7 @@ Firstly, in your keymap, do one of the following:
 |`KC_RCPC`  |Right Control when held, `)` when tapped   |
 |`KC_LAPO`  |Left Alt when held, `(` when tapped        |
 |`KC_RAPC`  |Right Alt when held, `)` when tapped       |
-|`KC_SFTENT`|Right Shift when held, `Enter` when tapped |
+|`KC_SFTENT`|Right Shift when held, Enter when tapped   |
 
 ## Caveats
 
@@ -38,10 +38,10 @@ By default Space Cadet assumes a US ANSI layout, but if your layout uses differe
 |----------------|-------------------------------|---------------------------------------------------------------------------------|
 |`LSPO_KEYS`     |`KC_LSFT, LSPO_MOD, LSPO_KEY`  |Send `KC_LSFT` when held, the mod and  key defined by `LSPO_MOD` and `LSPO_KEY`. |
 |`RSPC_KEYS`     |`KC_RSFT, RSPC_MOD, RSPC_KEY`  |Send `KC_RSFT` when held, the mod and  key defined by `RSPC_MOD` and `RSPC_KEY`. |
-|`LCPO_KEYS`     |`KC_LCTL, KC_LCTL, KC_9`       |Send `KC_LCTL` when held, the mod `KC_LCTL` with the key `KC_9` when tapped.     |
-|`RCPC_KEYS`     |`KC_RCTL, KC_RCTL, KC_0`       |Send `KC_RCTL` when held, the mod `KC_RCTL` with the key `KC_0` when tapped.     |
-|`LAPO_KEYS`     |`KC_LALT, KC_LALT, KC_9`       |Send `KC_LALT` when held, the mod `KC_LALT` with the key `KC_9` when tapped.     |
-|`RAPC_KEYS`     |`KC_RALT, KC_RALT, KC_0`       |Send `KC_RALT` when held, the mod `KC_RALT` with the key `KC_0` when tapped.     |
+|`LCPO_KEYS`     |`KC_LCTL, KC_LSFT, KC_9`       |Send `KC_LCTL` when held, the mod `KC_LSFT` with the key `KC_9` when tapped.     |
+|`RCPC_KEYS`     |`KC_RCTL, KC_RSFT, KC_0`       |Send `KC_RCTL` when held, the mod `KC_RSFT` with the key `KC_0` when tapped.     |
+|`LAPO_KEYS`     |`KC_LALT, KC_LSFT, KC_9`       |Send `KC_LALT` when held, the mod `KC_LSFT` with the key `KC_9` when tapped.     |
+|`RAPC_KEYS`     |`KC_RALT, KC_RSFT, KC_0`       |Send `KC_RALT` when held, the mod `KC_RSFT` with the key `KC_0` when tapped.     |
 |`SFTENT_KEYS`   |`KC_RSFT, KC_TRNS, SFTENT_KEY` |Send `KC_RSFT` when held, no mod with the key `SFTENT_KEY` when tapped.          |
 
 

docs/features.md

@@ -25,7 +25,7 @@ QMK has a staggering number of features for building your keyboard. It can take
 * [PS2 Mouse](feature_ps2_mouse.md) - Driver for connecting a PS/2 mouse directly to your keyboard.
 * [RGB Light](feature_rgblight.md) - RGB lighting for your keyboard.
 * [RGB Matrix](feature_rgb_matrix.md) - RGB Matrix lights for per key lighting.
-* [Space Cadet](feature_space_cadet_shift.md) - Use your left/right shift keys to type parenthesis and brackets.
+* [Space Cadet](feature_space_cadet.md) - Use your left/right shift keys to type parenthesis and brackets.
 * [Stenography](feature_stenography.md) - Put your keyboard into Plover mode for stenography use.
 * [Swap Hands](feature_swap_hands.md) - Mirror your keyboard for one handed usage.
 * [Tap Dance](feature_tap_dance.md) - Make a single key do as many things as you want.

docs/keycodes.md

@@ -216,6 +216,11 @@ This is a reference only. Each group of keys links to the page documenting their
 |`KC_GESC`      |`GRAVE_ESC`|Escape when tapped, <code>&#96;</code> when pressed with Shift or GUI|
 |`KC_LSPO`      |           |Left Shift when held, `(` when tapped                                |
 |`KC_RSPC`      |           |Right Shift when held, `)` when tapped                               |
+|`KC_LCPO`      |           |Left Control when held, `(` when tapped                              |
+|`KC_RCPC`      |           |Right Control when held, `)` when tapped                             |
+|`KC_LAPO`      |           |Left Alt when held, `(` when tapped                                  |
+|`KC_RAPC`      |           |Right Alt when held, `)` when tapped                                 |
+|`KC_SFTENT`    |           |Right Shift when held, Enter when tapped                             |
 |`KC_LEAD`      |           |The [Leader key](feature_leader_key.md)                              |
 |`KC_LOCK`      |           |The [Lock key](feature_key_lock.md)                                  |
 |`FUNC(n)`      |`F(n)`     |Call `fn_action(n)` (deprecated)                                     |

docs/quantum_keycodes.md

@@ -1,6 +1,6 @@
 # Quantum Keycodes
 
-Quantum keycodes allow for easier customisation of your keymap than the basic ones provide, without having to define custom actions.
+Quantum keycodes allow for easier customization of your keymap than the basic ones provide, without having to define custom actions.
 
 All keycodes within quantum are numbers between `0x0000` and `0xFFFF`. Within your `keymap.c` it may look like you have functions and other special cases, but ultimately the C preprocessor will translate those into a single 4 byte integer. QMK has reserved `0x0000` through `0x00FF` for standard keycodes. These are keycodes such as `KC_A`, `KC_1`, and `KC_LCTL`, which are basic keys defined in the USB HID specification.
 
@@ -16,6 +16,11 @@ On this page we have documented keycodes between `0x00FF` and `0xFFFF` which are
 |`KC_GESC`      |`GRAVE_ESC`|Escape when tapped, <code>&#96;</code> when pressed with Shift or GUI|
 |`KC_LSPO`      |           |Left Shift when held, `(` when tapped                                |
 |`KC_RSPC`      |           |Right Shift when held, `)` when tapped                               |
+|`KC_LCPO`      |           |Left Control when held, `(` when tapped                              |
+|`KC_RCPC`      |           |Right Control when held, `)` when tapped                             |
+|`KC_LAPO`      |           |Left Alt when held, `(` when tapped                                  |
+|`KC_RAPC`      |           |Right Alt when held, `)` when tapped                                 |
+|`KC_SFTENT`    |           |Right Shift when held, Enter when tapped                             |
 |`KC_LEAD`      |           |The [Leader key](feature_leader_key.md)                              |
 |`KC_LOCK`      |           |The [Lock key](feature_key_lock.md)                                  |
 |`FUNC(n)`      |`F(n)`     |Call `fn_action(n)` (deprecated)                                     |

docs/zh-cn/contributing.md

@@ -0,0 +1,205 @@
+# 如何做贡献
+
+👍🎉 首先感谢各位百忙之中抽空阅读本文档，并为我们无私奉献。给您点赞啦！ 🎉👍
+
+第三方的帮助让Q酱成长了许多呢，Q酱也从你们那学到了不少新东西。Q酱希望每一个想帮助我的人都能很方便的做出有用的贡献。在这里我给摩拳擦掌的你们写了一点引导，让你们的代码在不对我做重大改动的情况下都能成功的被采纳哦。
+
+* [项目概况](#项目概况)
+* [代码规范](#代码规范)
+* [一般教程](#一般教程)
+* [行为守则对于我来说有何意义?](#行为守则对于我来说有何意义?)
+
+## 这文章巨长无比不想读啊! 我就想问个问题而已!
+
+您要是想问关于Q酱的问题的话可以在[OLKB Subreddit](https://reddit.com/r/olkb)或者是[Discord](https://discord.gg/Uq7gcHh)随意问。
+
+请记住:
+
+* 维护Q酱的小可爱有的时候可能会有点忙，不能及时回答您的问题，耐心等等，他们都是很nice的人呀。
+* 维护Q酱的人都是很无私的善良的人。无论是贡献代码还是回答问题，都是义务的。有时见到他们努力回答各种问题，解决各种BUG，Q酱也是很心疼的。
+* 您可以看看下面的教程，可以让您的问题浅显易懂，更容易回答：
+  * https://opensource.com/life/16/10/how-ask-technical-questions
+  * http://www.catb.org/esr/faqs/smart-questions.html
+
+# 项目概况
+
+Q酱很大一部分是用C语言组成的，不过有一小部分特性是C++的。怎么说呢，都是我的一部分，两个我都爱。Q酱一般是在键盘上的嵌入式处理器那里工作的，尤其与AVR([LUFA](http://www.fourwalledcubicle.com/LUFA.php))和ARM ([ChibiOS](http://www.chibios.com))两小哥哥搭配，干活不累，嘻嘻。如果您精通Arduino的话您会发现很多熟悉的概念，但也有点不爽，因为您以前的经验可能没法用来帮助Q酱。
+
+<!-- 需要修正: 这里放些学习C语言的资源。另外感谢修正的小可爱。谢谢您了。-->
+
+# Q酱，我在哪能帮助你嘞?
+
+您要是有问题的话可以 [提出一个issue](https://github.com/qmk/qmk_firmware/issues) 或 [在Discord上交流一下](https://discord.gg/Uq7gcHh).
+
+# Q酱，我如何帮助你?
+
+您以前是否没为开源贡献过代码，而又想知道帮助Q酱是怎么一回事? 稍安勿躁，咱给您总结一下！
+
+0. 先注册一个 [GitHub](https://github.com) 账户。
+1. 做好一个你要贡献的布局，那就要 [找一个你想解决的问题](https://github.com/qmk/qmk_firmware/issues)，或者 [找一个你想添加的特性](https://github.com/qmk/qmk_firmware/issues?q=is%3Aopen+is%3Aissue+label%3Afeature)。
+2. 把关联着问题的仓库分叉（fork）到你的仓库。这样你在`你的GitHub用户名/qmk_firmware`就有一个仓库备份啦。
+3. 使用 `git clone https://github.com/此处添GitHub用户名/此处添仓库名.git`这个命令把仓库同步到你的电脑中。
+4. 您要是想开发一个新特性的话可以先创建一个issue和Q酱的维护者讨论一下您要做什么。
+5. 使用`git checkout -b 此处写分支名字（别用汉字）`命令来创建一个分支（branch）用于开发。
+6. 对要解决的问题或要添加的特性进行适当的更改。
+7. 使用 `git add 把改变的文件的目录写这里` 可以添加改变的文件内容到git用于管理工程状态的索引（快照）里。
+8. 使用 `git commit -m "这里写修改的相关信息"` 来描述你做出了什么修改。
+9. 使用 `git push origin 此处写分支名字`来把你的更改同步到GitHub库里（反正不是打篮球那个库里）。
+10. 提交一个[QMK 固件的pull request](https://github.com/qmk/qmk_firmware/pull/new/master)。
+11. 给你的pull request拟一个标题，包括简短的描述和问题或错误代码。比如, 你可以起一个这样的"Added more log outputting to resolve #4352"（最好用英语，毕竟Q酱的中文也不是那么的溜，有可能会看不懂中文）。
+12. 在描述（description）里面写你做了哪些更改，你的代码里还存在什么问题, 或者你想问维护的小可爱们的问题。你的your pull request有点小问题无伤大雅(本来也没有完美的代码嘛), 维护的小可爱们会竭尽全力帮您改进的！
+13. 维护人员审查代码可能需要一些时间。
+14. 维护人员会通知您要更改什么地方，然后您就按照建议改一改。
+15. 预祝您合并成功！
+
+# 代码规范
+
+其实也没有什么特别严格的规范啦，但是俗话说的好：没有规矩，不成方圆。您可以看一下您的要改动的代码周围的画风，然后保持队形。如果你感觉周围都不知道是什么牛鬼蛇神的话就看看下面的建议：
+
+* 我们用肆(4)个空格来缩进(软件中也可以设置到Tab键)
+* 我们使用改良的1TBS(允许单行样式)
+  * 左大括号: 在开放性语句块那行的末尾
+  * 右大括号: 和开放性语句块第一个字母对齐
+  * Else If: 将右大括号放在行的开头，下一个左大括号放在同一行的结尾
+  * 可选大括号: 可选大括号是必选的
+    * 应该这样: if (condition) { return false; }
+    * 不应该这样: if (condition) return false;
+* 建议使用C语言风格的注释: `/* */`
+  * 把注释想象成一个描述特征的故事
+  * 充分使用注释来描述你为何这样修改
+  * 有些公认的东西就不要写到注释里面了
+  * 如果你不知道注释是否多余,看下面
+* 一般不要主动换行，主动换行的话每行不要超过76列
+* 要把 `#pragma once` 放到头文件的开始哦，抛弃老土的(`#ifndef THIS_FILE_H`, `#define THIS_FILE_H`, ..., `#endif`)吧
+* 下面两种预处理命令都可以用: `#ifdef DEFINED` 还有 `#if defined(DEFINED)`
+  * 以上那句对处女座不是很友好哈，处女座的朋友们就别纠结了，直接 `#if defined(DEFINED)` 。
+  * 还有就是选好一种风格就一直用，一直用一直爽，不要朝三暮四, 除非你要变化到多重条件的 `#if`。
+  * `#` 和 `if`要挨在一起哦，再让本空格在中间冒充电灯泡本空格会生气的。
+  * 以下是缩进规则:
+    * 首先考虑可读性，强迫症的朋友们总想要保持代码的高一致性，这样可不好。
+    * 保证文件已有风格不变。如果代码本来就是杂糅风格，那就见机行事，让你的修改更有意义些。
+    * 其实你也可以在缩进的时候看看周围其他代码，然后范水模山，预处理命令可以有自己的缩进风格。
+
+可以参照下面:
+
+```c
+/* foo 的 Enums*/
+enum foo_state {
+  FOO_BAR,
+  FOO_BAZ,
+};
+
+/* 有返回值的情况 */
+int foo(void) {
+  if (some_condition) {
+    return FOO_BAR;
+  } else {
+    return -1;
+  }
+}
+```
+
+# Clang-format的自动格式化
+[Clang-format](https://clang.llvm.org/docs/ClangFormat.html) 是LLVM的一部分，可以帮你自动格式化代码。我们给你准备好了一个适用于以上规范的配置文件，会帮你调整缩进和换行，你只需要写好括号就好。有了它，你再也不用担心调整代码格式太耗时，没有时间陪伴自己（虚构）的另一半了。
+
+使用[LLVM 完整安装](http://llvm.org/builds/)可以在Windows上安装clang-format, Ubuntu用户要用`sudo apt install clang-format`。
+
+命令行的朋友们, 加上 `-style=file`选项就会自动在QMK的根目录寻找.clang-format配置文件了。
+
+VSCode用户, 标准的 C/C++ 插件就支持clang-format, 或者可以用[独立扩展](https://marketplace.visualstudio.com/items?itemName=LLVMExtensions.ClangFormat)也行。
+
+有些东西(比如LAYOUT宏) 会被clang-format打乱，所以那些文件就别用clang-format了,这里就教您一个小窍门，在`// clang-format off` 和 `//clang-format on`之间装上会被搞乱的代码就好了。
+
+# 一般教程
+
+你可以给Q酱的不同部分添砖加瓦，但也要用不同的方法严谨检查。不论你修改哪里最好还是看看下边。
+
+* 将PR（pull request）分成一个个的逻辑单元。 比如，不要一次将两个新特性PR出去。要添加的特性排好队，一个一个来。
+* 提交之前看一眼，`git diff --check`的空格一定要写对了
+* 确定你的代码能通过编译
+  * 布局: 确定`make keyboard:your_new_keymap` 不返回错误
+  * 键盘: 确定 `make keyboard:all` 不返回错误
+  * 核心代码: 确定 `make all` 不返回错误
+* 提交的信息尽量明确。第一行写点简短介绍(每行不多于70个英文字母), 第二行空着,第三行和后面就要写些必要的细节了。最好用英文写，比如:
+
+```
+Adjust the fronzlebop for the kerpleplork
+
+The kerpleplork was intermittently failing with error code 23. The root cause was the fronzlebop setting, which causes the kerpleplork to activate every N iterations.
+
+Limited experimentation on the devices I have available shows that 7 is high enough to avoid confusing the kerpleplork, but I'd like to get some feedback from people with ARM devices to be sure.
+```
+
+## 文档
+
+想帮助Q酱当然是先看文档最简单了。找到这个文档哪里错了然后改正它对于你来说超级简单! 我们也对有写文档能力的人求贤若渴，如果你是对的人[点这个](#Q酱，我在哪能帮助你嘞?)!
+
+文档呢，都静静的放在`qmk_firmware/docs` 目录里, 也或者您想为网页做贡献的话也是可以的哦。
+
+在文档中附代码案例时, 先观察文档其他地方的命名规范。比如, 把enums的名字都改成像`my_layers`或者`my_keycodes`来防止名字不一致的enums被当作特务枪毙:
+
+```c
+enum my_layers {
+  _FIRST_LAYER,
+  _SECOND_LAYER
+};
+
+enum my_keycodes {
+  FIRST_LAYER = SAFE_RANGE,
+  SECOND_LAYER
+};
+```
+
+## 布局
+
+大多数QMK新手都从创建一个自己的布局开始。我们尽力保证布局规范宽松 (毕竟布局是个性的体现) 不过建议遵守以下准则，这样可以让别人更好理解你的代码
+
+* 用 [模板](documentation_templates.md)写个`readme.md`。
+* 所有的布局PR都会被squash, 如果你想知道你的提交是怎么被squash的那你就自己来吧
+* 不要把新特性和布局一起PR。可以分别PR他们
+* 布局文件夹就不要放`Makefile`了，这个操作都过时啦
+* 更新文件头部的copyrights(看`%YOUR_NAME%`那)
+
+## 键盘
+
+QMK的最终归宿是键盘。有些键盘是社区维护的，有一些是制作这些键盘的人维护的。`readme.md`会告诉你是谁维护了这个键盘，如果你对某个键盘有疑问，可以 [创建一个Issue](https://github.com/qmk/qmk_firmware/issues) 来问一问维护者。
+
+我们建议你按下面的来操作:
+
+* 用[模板](documentation_templates.md)写`readme.md`。
+* 提交数量尽量合理，不然我们可就要把你的PR给squash了。
+* 不要把新特性和新键盘一起PR。可以分别PR他们
+* 用父文件夹的名字命名 `.c`/`.h`文件, 比如`/keyboards/<kb1>/<kb2>/<kb2>.[ch]`
+* 键盘文件夹就不要放`Makefile`了，这个操作都过时啦
+* 更新文件头部的copyrights(看`%YOUR_NAME%`那)
+
+## Quantum/TMK 核心
+
+在您废寝忘食地开发Q酱新特性或者帮Q酱驱虫之前，一定要确保你的工作是有意义的。看看[了解QMK](understanding_qmk.md)你会对Q酱有更深的了解，这个文档将带你领略QMK的程序流程。现在你应该和维护团对谈谈来了解实现你想法的最佳方法了。一下渠道都可以：
+
+* [在Discord交流](https://discord.gg/Uq7gcHh)
+* [建立一个Issue](https://github.com/qmk/qmk_firmware/issues/new)
+
+新特性和BUG的修复影响所有键盘。开发组也在翻修QMK。所以，在实施重大返修之前一定要讨论一下。如果你在没有事先与维护团队沟通的情况下提交了一个PR，而且你的选择与维护团队的计划方向不符，那你可能要面临大改了。
+
+修复BUG或者开发新特性之前看看这个：
+
+* **默认不启用** - QMK运行的芯片多数内存有限，所以首要考虑的还应该是布局不要被破坏，于是特性默认是不启用的。你喜欢什么特性的话就打开它，如果你觉得有些特性应该默认开启或者你能帮助缩减代码，那就联系维护组吧。
+* **提交之前在本地编译** - 这个简直就是家喻户晓了，但是也确实需要编译啊！ 我们的Travis系统会发现一切问题，但是自己编译一下可要比在线等快多了。
+* **注意版本和芯片平台** - 有那么几个键盘有支持不同配置甚至是不同芯片的版本。试着写一个能AVR和ARM两个平台运行的特性，或者在不支持的平台自动禁用。
+* **解释你的新特性** - 在`docs/`写个文档, 你可以创建新文档或者写到现有文档中。如果你不把它记录下来，其他人就无法从你的努力中获益。
+
+也可以看看以下建议：
+
+* 提交数量尽量合理，不然我们可就要把你的PR给squash了。
+* 不要把新特性、布局和键盘一起PR。可以分别PR他们。
+* 给你的特性写[单元测试](unit_testing.md)。
+* 你编辑的文件风格要一致，如果风格不明确或者是混搭风的，你就要先看看[代码规范](#代码规范)确认情况。
+
+## 重构
+
+为了保持QMK脉络清晰，Q酱打算深入规划重构一下自己，然后让合作者进行修改。如果你有重构的思路或建议[创建一个issue](https://github.com/qmk/qmk_firmware/issues), Q酱很乐意讨论一下怎么改进一下。
+
+# 行为守则对于我来说有何意义?
+
+我们的[行为守则](https://github.com/qmk/qmk_firmware/blob/master/CODE_OF_CONDUCT.md) 是说明您有责任尊重和礼貌地对待项目中的每个人，无论他们的身份如何。 如果你是我们行为准则所描述的不当行为的受害者，我们将站在你这边，并按照行为准则对施暴者进行适当谴责。

docs/zh-cn/faq.md

@@ -0,0 +1,6 @@
+# 常见问题
+
+* [一般问题](faq_general.md)
+* [构建和编译QMK](faq_build.md)
+* [QMK调试和故障排除](faq_debug.md)
+* [布局问题](faq_keymap.md)

docs/zh-cn/getting_started_getting_help.md

@@ -0,0 +1,15 @@
+# 获得帮助
+
+有很多方法来获得关于QMK的帮助.
+
+## 实时聊天
+
+你可以在我们的主要[Discord服务器](https://discord.gg/Uq7gcHh)找到QMK的开发者和用户。有很多讨论固件的不同频道, 工具箱(Toolbox), 硬件,配置工具(configurator).
+
+## OLKB Subreddit
+
+QMK的官方论坛是[/r/olkb](https://reddit.com/r/olkb) 在[reddit.com](https://reddit.com)上.
+
+## Github的Issue
+
+你可以在GitHub上 [提出issue](https://github.com/qmk/qmk_firmware/issues).当您的问题需要长期讨论或调试时，这尤其方便。

docs/zh-cn/getting_started_github.md

@@ -0,0 +1,59 @@
+# 如何在QMK中使用Github
+
+Github can be a little tricky to those that aren't familiar with it - this guide will walk through each step of forking, cloning, and submitting a pull request with QMK.
+
+?> 本教程假设您已安装GitHub，并且您喜欢使用命令行工作。
+
+首先 [Github上的QMK页面](https://github.com/qmk/qmk_firmware), 您能看到右上方有个按钮写着"Fork":
+
+![从Github上分叉](http://i.imgur.com/8Toomz4.jpg)
+
+如果你是某组织成员，你将需要选择分叉到哪个账户。一般情况下, 你是想要分叉到你的私人账户下。当你完成分叉 (有时需要等一会), 点击"Clone or Download" 按钮:
+
+!从Github下载](http://i.imgur.com/N1NYcSz.jpg)
+
+你要选择 "HTTPS", 然后选择链接复制:
+
+![HTTPS链接](http://i.imgur.com/eGO0ohO.jpg)
+
+然后，在命令行输入`git clone `，然后粘贴你的链接:
+
+```
+user@computer:~$ git clone https://github.com/whoeveryouare/qmk_firmware.git
+Cloning into 'qmk_firmware'...
+remote: Counting objects: 46625, done.
+remote: Compressing objects: 100% (2/2), done.
+remote: Total 46625 (delta 0), reused 0 (delta 0), pack-reused 46623
+Receiving objects: 100% (46625/46625), 84.47 MiB | 3.14 MiB/s, done.
+Resolving deltas: 100% (29362/29362), done.
+Checking out files: 100% (2799/2799), done.
+```
+
+现在你本地计算机有QMK的分叉了,你可以添加你的布局了, 为你的键盘编译并刷新固件吧。如果你觉得你的修改很不错, 你可以添加,提交,然后想你的分叉推出（pull）你的改变，像这样:
+
+```
+user@computer:~$ git add .
+user@computer:~$ git commit -m "adding my keymap"
+[master cccb1608] adding my keymap
+ 1 file changed, 1 insertion(+)
+ create mode 100644 keyboards/planck/keymaps/mine/keymap.c
+user@computer:~$ git push
+Counting objects: 1, done.
+Delta compression using up to 4 threads.
+Compressing objects: 100% (1/1), done.
+Writing objects: 100% (1/1), 1.64 KiB | 0 bytes/s, done.
+Total 1 (delta 1), reused 0 (delta 0)
+remote: Resolving deltas: 100% (1/1), completed with 1 local objects.
+To https://github.com/whoeveryouare/qmk_firmware.git
+ + 20043e64...7da94ac5 master -> master
+```
+
+现在你的改动已经在你Github上的分支中了 - 如果你回到这 (`https://github.com/你的GitHub账户名/qmk_firmware`) ,你可以点击下方所示按钮创建 "New Pull Request":
+
+![新的 Pull Request](http://i.imgur.com/DxMHpJ8.jpg)
+
+现在你可以看到你所做的一切 - 如果看起来不错, 就可以点击 "Create Pull Request"定稿了:
+
+![创建Pull Request](http://i.imgur.com/Ojydlaj.jpg)
+
+提交后,我们会开跟你说你的改动,要求您进行更改, 并最终接受您的更改!感谢您为QMK做的贡献 :)

docs/zh-cn/newbs.md

@@ -0,0 +1,23 @@
+# QMK菜鸟教程
+
+QMK是为你机械硬盘设计的的一个强大的开源固件。使用QMK可以很简单的让你的定制键盘变得强大。看完这篇文章，无论你是菜鸟还是大佬，都可以顺利的使用QMK来定制键盘。
+
+你是否为不知道你的键盘能不能运行QMK而苦恼? 如果你的机械键盘是你自己做的，那么这把键盘一般可以运行QMK。我们提供了[一大堆自制键盘](http://qmk.fm/keyboards/), 所以即便你的键盘不能运行QMK你也很容易能找到满足你需求的键盘。
+
+## 概览
+
+这个教程有7个主要部分：
+
+* [新手上路](newbs_getting_started.md)
+* [用命令行构建你的第一个固件](newbs_building_firmware.md)
+* [用在线界面构建你的第一个固件](newbs_building_firmware_configurator.md)
+* [刷新固件](newbs_flashing.md)
+* [测试和调试](newbs_testing_debugging.md)
+* [Git最佳实践](newbs_best_practices.md)
+* [其他学习资源](newbs_learn_more_resources.md)
+
+这份教程旨在帮助没有固件构建经验的人，也是根据该目的做出选择和建议。这些程序有很多替代方法，大部分替代我们都支持。如果你对完成一个任务有疑问，可以[向我们寻求帮助](getting_started_getting_help.md).
+
+## 其他资源
+
+* [Thomas Baart的 QMK基础博客](https://thomasbaart.nl/category/mechanical-keyboards/firmware/qmk/qmk-basics/) – 这是一个用户创建的博客，涵盖了为新手准备的使用QMK的基础知识。

keyboards/dz60/keymaps/billiams/keymap.c

@@ -12,7 +12,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
    * |-----------------------------------------------------------------------------------------+
    * | Shift     |  Z  |  X  |  C  |  V  |  B  |  N  |  M  |  ,  |  .  |Tap(/) Shft|  U  | ESC |
    * |-----------------------------------------------------------------------------------------+
-   * | Ctrl |  Alt  |  Cmd  |              Space                | Cmd |  Fn  |  L  |  D  |  R  |
+   * | Ctrl |  Alt  |  Cmd  |              Space                | Alt |  Fn  |  L  |  D  |  R  |
    * `-----------------------------------------------------------------------------------------'
    */
 
@@ -21,16 +21,16 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
       KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS,
       MO(1), KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_ENT,
       KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, _______, RSFT_T(KC_SLSH) , KC_UP, KC_ESCAPE,
-      KC_LCTL, KC_LALT, KC_LGUI, KC_SPC, KC_SPC, KC_SPC, KC_RGUI, MO(1), KC_LEFT, KC_DOWN, KC_RIGHT
+      KC_LCTL, KC_LALT, KC_LGUI, KC_SPC, KC_SPC, KC_SPC, KC_RALT, MO(1), KC_LEFT, KC_DOWN, KC_RIGHT
       ),
 
   /* FN Layer
    * ,-----------------------------------------------------------------------------------------.
    * |     |  F1 |  F2 |  F3 |  F4 |  F5 |  F6 |  F7 |  F8 |  F9 | F10 | F11 | F12 |    DEL    |
    * |-----------------------------------------------------------------------------------------+
-   * |        |RBB T|RGB M| Hue-| Hue+| Sat-| Sat+| Val-| Val+|     |     | MUTE | Vol- | Vol+ |
+   * |        |RBB T|RGB M| Hue-| Hue+| Sat-| Sat+| Val-| Val+| Mute | Vol-| Vol+| Prev | Next |
    * |-----------------------------------------------------------------------------------------+
-   * |         |     |     |     |     |     |     |     |    |     | Prev | Next | Play/Pause |
+   * |         |     |     |     |     |     | Left| Down| Up |Right|      |      | Play/Pause |
    * |-----------------------------------------------------------------------------------------+
    * |           |     |     |     |     |     |     |     |Scr- |Scr+ |           |PG_UP|RESET|
    * |-----------------------------------------------------------------------------------------+
@@ -40,8 +40,8 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
 
   LAYOUT_directional(
       _______, KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,  KC_F10, KC_F11, KC_F12, _______, KC_DEL,
-      _______, RGB_TOG, RGB_MOD, RGB_HUD, RGB_HUI, RGB_SAD, RGB_SAI, RGB_VAD, RGB_VAI, _______, _______, KC_MUTE, KC__VOLDOWN, KC__VOLUP,
-      _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_MRWD, KC_MFFD,
+      _______, RGB_TOG, RGB_MOD, RGB_HUD, RGB_HUI, RGB_SAD, RGB_SAI, RGB_VAD, RGB_VAI, KC_MUTE, KC__VOLDOWN, KC__VOLUP, KC_MRWD, KC_MFFD,
+      _______, _______, _______, _______, _______, _______, KC_LEFT, KC_DOWN, KC_UP, KC_RIGHT, _______, _______,
       KC_MPLY, _______, _______, _______, _______, _______, _______, _______, _______, KC_BRID, KC_BRIU, _______, _______, KC_PGUP, RESET,
       _______, _______, _______, _______, _______, _______, _______, _______, KC_HOME, KC_PGDOWN, KC_END
       ),

keyboards/dz60/keymaps/billiams/readme.md

@@ -10,9 +10,8 @@ Settings:
 * Del is available as `Fn` + `Backspace`
 * `/ ?` are available when you tap the right shift. Otherwise RShift is shift when held down
 * RESET is available as `Fn`+ ` ESC`
-* Underglow toggle and mode selection are available as `Fn` + `Q` and `Fn` + `S`. Yes your keyboard has lights even if you didn't get the LEDs. Bonus!
-* Media play/pause doesn't seem to work with anything but iTunes at the moment. FML
-
+* Underglow toggle is available as `Fn` + `Q`. Yes your keyboard has lights even if you didn't get the LEDs. Bonus!
+* vim-style arrow key bindings H J K L in layer 1
 
 ### Initial Installation
 
@@ -51,7 +50,7 @@ Hope this helps!
 |-----------------------------------------------------------------------------------------+
 | Shift     |  Z  |  X  |  C  |  V  |  B  |  N  |  M  |  ,  |  .  | Tap:/ RSh |  U  | ESC |
 |-----------------------------------------------------------------------------------------+
-| Ctrl |  Alt  |  Cmd  |              Space                | Cmd |  Fn  |  L  |  D  |  R  |
+| Ctrl |  Alt  |  Cmd  |              Space                | Alt |  Fn  |  L  |  D  |  R  |
 `-----------------------------------------------------------------------------------------'
 ```
 
@@ -61,9 +60,9 @@ FN Layer
 ,-----------------------------------------------------------------------------------------.
 |  `  |  F1 |  F2 |  F3 |  F4 |  F5 |  F6 |  F7 |  F8 |  F9 | F10 | F11 | F12 |    DEL    |
 |-----------------------------------------------------------------------------------------+
-|        |RBB T|RGB M| Hue-| Hue+| Sat-| Sat+| Val-| Val+|     |     | MUTE | Vol- | Vol+ |
+|        |RBB T|RGB M| Hue-| Hue+| Sat-| Sat+| Val-| Val+| Mute | Vol-| Vol+| Prev | Next |
 |-----------------------------------------------------------------------------------------+
-|         |     |     |     |     |     |     |     |     |    | Prev | Next | Play/Pause |
+|         |     |     |     |     |     | Left| Down| Up |Right|      |      | Play/Pause |
 |-----------------------------------------------------------------------------------------+
 |           |     |     |     |     |     |     |     |Scr- |Scr+ |         | PG_UP |RESET|
 |-----------------------------------------------------------------------------------------+

keyboards/dztech/boards/GENERIC_STM32_F303XC/board.c

@@ -1,126 +0,0 @@
-/*
-    ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio
-
-    Licensed under the Apache License, Version 2.0 (the "License");
-    you may not use this file except in compliance with the License.
-    You may obtain a copy of the License at
-
-        http://www.apache.org/licenses/LICENSE-2.0
-
-    Unless required by applicable law or agreed to in writing, software
-    distributed under the License is distributed on an "AS IS" BASIS,
-    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-    See the License for the specific language governing permissions and
-    limitations under the License.
-*/
-
-#include "hal.h"
-
-#if HAL_USE_PAL || defined(__DOXYGEN__)
-/**
- * @brief   PAL setup.
- * @details Digital I/O ports static configuration as defined in @p board.h.
- *          This variable is used by the HAL when initializing the PAL driver.
- */
-const PALConfig pal_default_config = {
-#if STM32_HAS_GPIOA
-  {VAL_GPIOA_MODER, VAL_GPIOA_OTYPER, VAL_GPIOA_OSPEEDR, VAL_GPIOA_PUPDR,
-   VAL_GPIOA_ODR,   VAL_GPIOA_AFRL,   VAL_GPIOA_AFRH},
-#endif
-#if STM32_HAS_GPIOB
-  {VAL_GPIOB_MODER, VAL_GPIOB_OTYPER, VAL_GPIOB_OSPEEDR, VAL_GPIOB_PUPDR,
-   VAL_GPIOB_ODR,   VAL_GPIOB_AFRL,   VAL_GPIOB_AFRH},
-#endif
-#if STM32_HAS_GPIOC
-  {VAL_GPIOC_MODER, VAL_GPIOC_OTYPER, VAL_GPIOC_OSPEEDR, VAL_GPIOC_PUPDR,
-   VAL_GPIOC_ODR,   VAL_GPIOC_AFRL,   VAL_GPIOC_AFRH},
-#endif
-#if STM32_HAS_GPIOD
-  {VAL_GPIOD_MODER, VAL_GPIOD_OTYPER, VAL_GPIOD_OSPEEDR, VAL_GPIOD_PUPDR,
-   VAL_GPIOD_ODR,   VAL_GPIOD_AFRL,   VAL_GPIOD_AFRH},
-#endif
-#if STM32_HAS_GPIOE
-  {VAL_GPIOE_MODER, VAL_GPIOE_OTYPER, VAL_GPIOE_OSPEEDR, VAL_GPIOE_PUPDR,
-   VAL_GPIOE_ODR,   VAL_GPIOE_AFRL,   VAL_GPIOE_AFRH},
-#endif
-#if STM32_HAS_GPIOF
-  {VAL_GPIOF_MODER, VAL_GPIOF_OTYPER, VAL_GPIOF_OSPEEDR, VAL_GPIOF_PUPDR,
-   VAL_GPIOF_ODR,   VAL_GPIOF_AFRL,   VAL_GPIOF_AFRH},
-#endif
-#if STM32_HAS_GPIOG
-  {VAL_GPIOG_MODER, VAL_GPIOG_OTYPER, VAL_GPIOG_OSPEEDR, VAL_GPIOG_PUPDR,
-   VAL_GPIOG_ODR,   VAL_GPIOG_AFRL,   VAL_GPIOG_AFRH},
-#endif
-#if STM32_HAS_GPIOH
-  {VAL_GPIOH_MODER, VAL_GPIOH_OTYPER, VAL_GPIOH_OSPEEDR, VAL_GPIOH_PUPDR,
-   VAL_GPIOH_ODR,   VAL_GPIOH_AFRL,   VAL_GPIOH_AFRH},
-#endif
-#if STM32_HAS_GPIOI
-  {VAL_GPIOI_MODER, VAL_GPIOI_OTYPER, VAL_GPIOI_OSPEEDR, VAL_GPIOI_PUPDR,
-   VAL_GPIOI_ODR,   VAL_GPIOI_AFRL,   VAL_GPIOI_AFRH}
-#endif
-};
-#endif
-
-void enter_bootloader_mode_if_requested(void);
-
-/**
- * @brief   Early initialization code.
- * @details This initialization must be performed just after stack setup
- *          and before any other initialization.
- */
-void __early_init(void) {
-  enter_bootloader_mode_if_requested();
-  stm32_clock_init();
-}
-
-#if HAL_USE_SDC || defined(__DOXYGEN__)
-/**
- * @brief   SDC card detection.
- */
-bool sdc_lld_is_card_inserted(SDCDriver *sdcp) {
-
-  (void)sdcp;
-  /* TODO: Fill the implementation.*/
-  return true;
-}
-
-/**
- * @brief   SDC card write protection detection.
- */
-bool sdc_lld_is_write_protected(SDCDriver *sdcp) {
-
-  (void)sdcp;
-  /* TODO: Fill the implementation.*/
-  return false;
-}
-#endif /* HAL_USE_SDC */
-
-#if HAL_USE_MMC_SPI || defined(__DOXYGEN__)
-/**
- * @brief   MMC_SPI card detection.
- */
-bool mmc_lld_is_card_inserted(MMCDriver *mmcp) {
-
-  (void)mmcp;
-  /* TODO: Fill the implementation.*/
-  return true;
-}
-
-/**
- * @brief   MMC_SPI card write protection detection.
- */
-bool mmc_lld_is_write_protected(MMCDriver *mmcp) {
-
-  (void)mmcp;
-  /* TODO: Fill the implementation.*/
-  return false;
-}
-#endif
-
-/**
- * @brief   Board-specific initialization code.
- * @todo    Add your board-specific code, if any.
- */
-void boardInit(void) {
-}

keyboards/dztech/boards/GENERIC_STM32_F303XC/board.mk

@@ -1,5 +0,0 @@
-# List of all the board related files.
-BOARDSRC = $(BOARD_PATH)/boards/GENERIC_STM32_F303XC/board.c
-
-# Required include directories
-BOARDINC = $(BOARD_PATH)/boards/GENERIC_STM32_F303XC

keyboards/dztech/dz40rgb/bootloader_defs.h

@@ -1,7 +0,0 @@
-/* Address for jumping to bootloader on STM32 chips. */
-/* It is chip dependent, the correct number can be looked up here:
- * http://www.st.com/web/en/resource/technical/document/application_note/CD00167594.pdf
- * This also requires a patch to chibios:
- *  <tmk_dir>/tmk_core/tool/chibios/ch-bootloader-jump.patch
- */
-#define STM32_BOOTLOADER_ADDRESS 0x1FFFD800

keyboards/dztech/dz40rgb/chconf.h

@@ -1,520 +0,0 @@
-/*
-    ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio
-
-    Licensed under the Apache License, Version 2.0 (the "License");
-    you may not use this file except in compliance with the License.
-    You may obtain a copy of the License at
-
-        http://www.apache.org/licenses/LICENSE-2.0
-
-    Unless required by applicable law or agreed to in writing, software
-    distributed under the License is distributed on an "AS IS" BASIS,
-    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-    See the License for the specific language governing permissions and
-    limitations under the License.
-*/
-
-/**
- * @file    templates/chconf.h
- * @brief   Configuration file template.
- * @details A copy of this file must be placed in each project directory, it
- *          contains the application specific kernel settings.
- *
- * @addtogroup config
- * @details Kernel related settings and hooks.
- * @{
- */
-
-#ifndef CHCONF_H
-#define CHCONF_H
-
-#define _CHIBIOS_RT_CONF_
-
-/*===========================================================================*/
-/**
- * @name System timers settings
- * @{
- */
-/*===========================================================================*/
-
-/**
- * @brief   System time counter resolution.
- * @note    Allowed values are 16 or 32 bits.
- */
-#define CH_CFG_ST_RESOLUTION                32
-
-/**
- * @brief   System tick frequency.
- * @details Frequency of the system timer that drives the system ticks. This
- *          setting also defines the system tick time unit.
- */
-#define CH_CFG_ST_FREQUENCY                 100000
-
-/**
- * @brief   Time delta constant for the tick-less mode.
- * @note    If this value is zero then the system uses the classic
- *          periodic tick. This value represents the minimum number
- *          of ticks that is safe to specify in a timeout directive.
- *          The value one is not valid, timeouts are rounded up to
- *          this value.
- */
-#define CH_CFG_ST_TIMEDELTA                 2
-
-/** @} */
-
-/*===========================================================================*/
-/**
- * @name Kernel parameters and options
- * @{
- */
-/*===========================================================================*/
-
-/**
- * @brief   Round robin interval.
- * @details This constant is the number of system ticks allowed for the
- *          threads before preemption occurs. Setting this value to zero
- *          disables the preemption for threads with equal priority and the
- *          round robin becomes cooperative. Note that higher priority
- *          threads can still preempt, the kernel is always preemptive.
- * @note    Disabling the round robin preemption makes the kernel more compact
- *          and generally faster.
- * @note    The round robin preemption is not supported in tickless mode and
- *          must be set to zero in that case.
- */
-#define CH_CFG_TIME_QUANTUM                 0
-
-/**
- * @brief   Managed RAM size.
- * @details Size of the RAM area to be managed by the OS. If set to zero
- *          then the whole available RAM is used. The core memory is made
- *          available to the heap allocator and/or can be used directly through
- *          the simplified core memory allocator.
- *
- * @note    In order to let the OS manage the whole RAM the linker script must
- *          provide the @p __heap_base__ and @p __heap_end__ symbols.
- * @note    Requires @p CH_CFG_USE_MEMCORE.
- */
-#define CH_CFG_MEMCORE_SIZE                 0
-
-/**
- * @brief   Idle thread automatic spawn suppression.
- * @details When this option is activated the function @p chSysInit()
- *          does not spawn the idle thread. The application @p main()
- *          function becomes the idle thread and must implement an
- *          infinite loop.
- */
-#define CH_CFG_NO_IDLE_THREAD               FALSE
-
-/** @} */
-
-/*===========================================================================*/
-/**
- * @name Performance options
- * @{
- */
-/*===========================================================================*/
-
-/**
- * @brief   OS optimization.
- * @details If enabled then time efficient rather than space efficient code
- *          is used when two possible implementations exist.
- *
- * @note    This is not related to the compiler optimization options.
- * @note    The default is @p TRUE.
- */
-#define CH_CFG_OPTIMIZE_SPEED               TRUE
-
-/** @} */
-
-/*===========================================================================*/
-/**
- * @name Subsystem options
- * @{
- */
-/*===========================================================================*/
-
-/**
- * @brief   Time Measurement APIs.
- * @details If enabled then the time measurement APIs are included in
- *          the kernel.
- *
- * @note    The default is @p TRUE.
- */
-#define CH_CFG_USE_TM                       TRUE
-
-/**
- * @brief   Threads registry APIs.
- * @details If enabled then the registry APIs are included in the kernel.
- *
- * @note    The default is @p TRUE.
- */
-#define CH_CFG_USE_REGISTRY                 TRUE
-
-/**
- * @brief   Threads synchronization APIs.
- * @details If enabled then the @p chThdWait() function is included in
- *          the kernel.
- *
- * @note    The default is @p TRUE.
- */
-#define CH_CFG_USE_WAITEXIT                 TRUE
-
-/**
- * @brief   Semaphores APIs.
- * @details If enabled then the Semaphores APIs are included in the kernel.
- *
- * @note    The default is @p TRUE.
- */
-#define CH_CFG_USE_SEMAPHORES               TRUE
-
-/**
- * @brief   Semaphores queuing mode.
- * @details If enabled then the threads are enqueued on semaphores by
- *          priority rather than in FIFO order.
- *
- * @note    The default is @p FALSE. Enable this if you have special
- *          requirements.
- * @note    Requires @p CH_CFG_USE_SEMAPHORES.
- */
-#define CH_CFG_USE_SEMAPHORES_PRIORITY      FALSE
-
-/**
- * @brief   Mutexes APIs.
- * @details If enabled then the mutexes APIs are included in the kernel.
- *
- * @note    The default is @p TRUE.
- */
-#define CH_CFG_USE_MUTEXES                  TRUE
-
-/**
- * @brief   Enables recursive behavior on mutexes.
- * @note    Recursive mutexes are heavier and have an increased
- *          memory footprint.
- *
- * @note    The default is @p FALSE.
- * @note    Requires @p CH_CFG_USE_MUTEXES.
- */
-#define CH_CFG_USE_MUTEXES_RECURSIVE        FALSE
-
-/**
- * @brief   Conditional Variables APIs.
- * @details If enabled then the conditional variables APIs are included
- *          in the kernel.
- *
- * @note    The default is @p TRUE.
- * @note    Requires @p CH_CFG_USE_MUTEXES.
- */
-#define CH_CFG_USE_CONDVARS                 TRUE
-
-/**
- * @brief   Conditional Variables APIs with timeout.
- * @details If enabled then the conditional variables APIs with timeout
- *          specification are included in the kernel.
- *
- * @note    The default is @p TRUE.
- * @note    Requires @p CH_CFG_USE_CONDVARS.
- */
-#define CH_CFG_USE_CONDVARS_TIMEOUT         TRUE
-
-/**
- * @brief   Events Flags APIs.
- * @details If enabled then the event flags APIs are included in the kernel.
- *
- * @note    The default is @p TRUE.
- */
-#define CH_CFG_USE_EVENTS                   TRUE
-
-/**
- * @brief   Events Flags APIs with timeout.
- * @details If enabled then the events APIs with timeout specification
- *          are included in the kernel.
- *
- * @note    The default is @p TRUE.
- * @note    Requires @p CH_CFG_USE_EVENTS.
- */
-#define CH_CFG_USE_EVENTS_TIMEOUT           TRUE
-
-/**
- * @brief   Synchronous Messages APIs.
- * @details If enabled then the synchronous messages APIs are included
- *          in the kernel.
- *
- * @note    The default is @p TRUE.
- */
-#define CH_CFG_USE_MESSAGES                 TRUE
-
-/**
- * @brief   Synchronous Messages queuing mode.
- * @details If enabled then messages are served by priority rather than in
- *          FIFO order.
- *
- * @note    The default is @p FALSE. Enable this if you have special
- *          requirements.
- * @note    Requires @p CH_CFG_USE_MESSAGES.
- */
-#define CH_CFG_USE_MESSAGES_PRIORITY        TRUE
-
-/**
- * @brief   Mailboxes APIs.
- * @details If enabled then the asynchronous messages (mailboxes) APIs are
- *          included in the kernel.
- *
- * @note    The default is @p TRUE.
- * @note    Requires @p CH_CFG_USE_SEMAPHORES.
- */
-#define CH_CFG_USE_MAILBOXES                TRUE
-
-/**
- * @brief   Core Memory Manager APIs.
- * @details If enabled then the core memory manager APIs are included
- *          in the kernel.
- *
- * @note    The default is @p TRUE.
- */
-#define CH_CFG_USE_MEMCORE                  TRUE
-
-/**
- * @brief   Heap Allocator APIs.
- * @details If enabled then the memory heap allocator APIs are included
- *          in the kernel.
- *
- * @note    The default is @p TRUE.
- * @note    Requires @p CH_CFG_USE_MEMCORE and either @p CH_CFG_USE_MUTEXES or
- *          @p CH_CFG_USE_SEMAPHORES.
- * @note    Mutexes are recommended.
- */
-#define CH_CFG_USE_HEAP                     TRUE
-
-/**
- * @brief   Memory Pools Allocator APIs.
- * @details If enabled then the memory pools allocator APIs are included
- *          in the kernel.
- *
- * @note    The default is @p TRUE.
- */
-#define CH_CFG_USE_MEMPOOLS                 TRUE
-
-/**
- * @brief   Dynamic Threads APIs.
- * @details If enabled then the dynamic threads creation APIs are included
- *          in the kernel.
- *
- * @note    The default is @p TRUE.
- * @note    Requires @p CH_CFG_USE_WAITEXIT.
- * @note    Requires @p CH_CFG_USE_HEAP and/or @p CH_CFG_USE_MEMPOOLS.
- */
-#define CH_CFG_USE_DYNAMIC                  TRUE
-
-/** @} */
-
-/*===========================================================================*/
-/**
- * @name Debug options
- * @{
- */
-/*===========================================================================*/
-
-/**
- * @brief   Debug option, kernel statistics.
- *
- * @note    The default is @p FALSE.
- */
-#define CH_DBG_STATISTICS                   FALSE
-
-/**
- * @brief   Debug option, system state check.
- * @details If enabled the correct call protocol for system APIs is checked
- *          at runtime.
- *
- * @note    The default is @p FALSE.
- */
-#define CH_DBG_SYSTEM_STATE_CHECK           FALSE
-
-/**
- * @brief   Debug option, parameters checks.
- * @details If enabled then the checks on the API functions input
- *          parameters are activated.
- *
- * @note    The default is @p FALSE.
- */
-#define CH_DBG_ENABLE_CHECKS                FALSE
-
-/**
- * @brief   Debug option, consistency checks.
- * @details If enabled then all the assertions in the kernel code are
- *          activated. This includes consistency checks inside the kernel,
- *          runtime anomalies and port-defined checks.
- *
- * @note    The default is @p FALSE.
- */
-#define CH_DBG_ENABLE_ASSERTS               FALSE
-
-/**
- * @brief   Debug option, trace buffer.
- * @details If enabled then the trace buffer is activated.
- *
- * @note    The default is @p CH_DBG_TRACE_MASK_DISABLED.
- */
-#define CH_DBG_TRACE_MASK                   CH_DBG_TRACE_MASK_DISABLED
-
-/**
- * @brief   Trace buffer entries.
- * @note    The trace buffer is only allocated if @p CH_DBG_TRACE_MASK is
- *          different from @p CH_DBG_TRACE_MASK_DISABLED.
- */
-#define CH_DBG_TRACE_BUFFER_SIZE            128
-
-/**
- * @brief   Debug option, stack checks.
- * @details If enabled then a runtime stack check is performed.
- *
- * @note    The default is @p FALSE.
- * @note    The stack check is performed in a architecture/port dependent way.
- *          It may not be implemented or some ports.
- * @note    The default failure mode is to halt the system with the global
- *          @p panic_msg variable set to @p NULL.
- */
-#define CH_DBG_ENABLE_STACK_CHECK           TRUE
-
-/**
- * @brief   Debug option, stacks initialization.
- * @details If enabled then the threads working area is filled with a byte
- *          value when a thread is created. This can be useful for the
- *          runtime measurement of the used stack.
- *
- * @note    The default is @p FALSE.
- */
-#define CH_DBG_FILL_THREADS                 FALSE
-
-/**
- * @brief   Debug option, threads profiling.
- * @details If enabled then a field is added to the @p thread_t structure that
- *          counts the system ticks occurred while executing the thread.
- *
- * @note    The default is @p FALSE.
- * @note    This debug option is not currently compatible with the
- *          tickless mode.
- */
-#define CH_DBG_THREADS_PROFILING            FALSE
-
-/** @} */
-
-/*===========================================================================*/
-/**
- * @name Kernel hooks
- * @{
- */
-/*===========================================================================*/
-
-/**
- * @brief   Threads descriptor structure extension.
- * @details User fields added to the end of the @p thread_t structure.
- */
-#define CH_CFG_THREAD_EXTRA_FIELDS                                          \
-  /* Add threads custom fields here.*/
-
-/**
- * @brief   Threads initialization hook.
- * @details User initialization code added to the @p chThdInit() API.
- *
- * @note    It is invoked from within @p chThdInit() and implicitly from all
- *          the threads creation APIs.
- */
-#define CH_CFG_THREAD_INIT_HOOK(tp) {                                       \
-  /* Add threads initialization code here.*/                                \
-}
-
-/**
- * @brief   Threads finalization hook.
- * @details User finalization code added to the @p chThdExit() API.
- */
-#define CH_CFG_THREAD_EXIT_HOOK(tp) {                                       \
-  /* Add threads finalization code here.*/                                  \
-}
-
-/**
- * @brief   Context switch hook.
- * @details This hook is invoked just before switching between threads.
- */
-#define CH_CFG_CONTEXT_SWITCH_HOOK(ntp, otp) {                              \
-  /* Context switch code here.*/                                            \
-}
-
-/**
- * @brief   ISR enter hook.
- */
-#define CH_CFG_IRQ_PROLOGUE_HOOK() {                                        \
-  /* IRQ prologue code here.*/                                              \
-}
-
-/**
- * @brief   ISR exit hook.
- */
-#define CH_CFG_IRQ_EPILOGUE_HOOK() {                                        \
-  /* IRQ epilogue code here.*/                                              \
-}
-
-/**
- * @brief   Idle thread enter hook.
- * @note    This hook is invoked within a critical zone, no OS functions
- *          should be invoked from here.
- * @note    This macro can be used to activate a power saving mode.
- */
-#define CH_CFG_IDLE_ENTER_HOOK() {                                          \
-  /* Idle-enter code here.*/                                                \
-}
-
-/**
- * @brief   Idle thread leave hook.
- * @note    This hook is invoked within a critical zone, no OS functions
- *          should be invoked from here.
- * @note    This macro can be used to deactivate a power saving mode.
- */
-#define CH_CFG_IDLE_LEAVE_HOOK() {                                          \
-  /* Idle-leave code here.*/                                                \
-}
-
-/**
- * @brief   Idle Loop hook.
- * @details This hook is continuously invoked by the idle thread loop.
- */
-#define CH_CFG_IDLE_LOOP_HOOK() {                                           \
-  /* Idle loop code here.*/                                                 \
-}
-
-/**
- * @brief   System tick event hook.
- * @details This hook is invoked in the system tick handler immediately
- *          after processing the virtual timers queue.
- */
-#define CH_CFG_SYSTEM_TICK_HOOK() {                                         \
-  /* System tick event code here.*/                                         \
-}
-
-/**
- * @brief   System halt hook.
- * @details This hook is invoked in case to a system halting error before
- *          the system is halted.
- */
-#define CH_CFG_SYSTEM_HALT_HOOK(reason) {                                   \
-  /* System halt code here.*/                                               \
-}
-
-/**
- * @brief   Trace hook.
- * @details This hook is invoked each time a new record is written in the
- *          trace buffer.
- */
-#define CH_CFG_TRACE_HOOK(tep) {                                            \
-  /* Trace code here.*/                                                     \
-}
-
-/** @} */
-
-/*===========================================================================*/
-/* Port-specific settings (override port settings defaulted in chcore.h).    */
-/*===========================================================================*/
-
-#endif  /* CHCONF_H */
-
-/** @} */

keyboards/dztech/dz40rgb/config.h

@@ -21,7 +21,7 @@
 
 #define DEBOUNCE 3
 #define RGB_DISABLE_AFTER_TIMEOUT 0 // number of ticks to wait until disabling effects
-#define RGB_DISABLE_WHEN_USB_SUSPENDED false // turn off effects when suspended
+#define RGB_DISABLE_WHEN_USB_SUSPENDED true // turn off effects when suspended
 #define RGB_MATRIX_KEYPRESSES
 #define DISABLE_RGB_MATRIX_SPLASH
 #define DISABLE_RGB_MATRIX_MULTISPLASH

keyboards/dztech/dz40rgb/dz40rgb.c

@@ -181,28 +181,23 @@ led_config_t g_led_config = { {
 
 #endif
 
-
 void matrix_init_kb(void) {
     matrix_init_user();
 }
-
-
 void matrix_scan_kb(void) {
     matrix_scan_user();
 }
-
-
 bool process_record_kb(uint16_t keycode, keyrecord_t *record) {
     return process_record_user(keycode, record);
 }
-
-
 void suspend_power_down_kb(void)
 {
     rgb_matrix_set_suspend_state(true);
+    suspend_power_down_user();
 }
 
 void suspend_wakeup_init_kb(void)
 {
     rgb_matrix_set_suspend_state(false);
+    suspend_wakeup_init_user();
 }

keyboards/dztech/dz40rgb/halconf.h

@@ -1,388 +0,0 @@
-/*
-    ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio
-
-    Licensed under the Apache License, Version 2.0 (the "License");
-    you may not use this file except in compliance with the License.
-    You may obtain a copy of the License at
-
-        http://www.apache.org/licenses/LICENSE-2.0
-
-    Unless required by applicable law or agreed to in writing, software
-    distributed under the License is distributed on an "AS IS" BASIS,
-    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-    See the License for the specific language governing permissions and
-    limitations under the License.
-*/
-
-/**
- * @file    templates/halconf.h
- * @brief   HAL configuration header.
- * @details HAL configuration file, this file allows to enable or disable the
- *          various device drivers from your application. You may also use
- *          this file in order to override the device drivers default settings.
- *
- * @addtogroup HAL_CONF
- * @{
- */
-
-#ifndef HALCONF_H
-#define HALCONF_H
-
-#include "mcuconf.h"
-
-/**
- * @brief   Enables the PAL subsystem.
- */
-#if !defined(HAL_USE_PAL) || defined(__DOXYGEN__)
-#define HAL_USE_PAL                 TRUE
-#endif
-
-/**
- * @brief   Enables the ADC subsystem.
- */
-#if !defined(HAL_USE_ADC) || defined(__DOXYGEN__)
-#define HAL_USE_ADC                 FALSE
-#endif
-
-/**
- * @brief   Enables the CAN subsystem.
- */
-#if !defined(HAL_USE_CAN) || defined(__DOXYGEN__)
-#define HAL_USE_CAN                 FALSE
-#endif
-
-/**
- * @brief   Enables the DAC subsystem.
- */
-#if !defined(HAL_USE_DAC) || defined(__DOXYGEN__)
-#define HAL_USE_DAC                 TRUE
-#endif
-
-/**
- * @brief   Enables the EXT subsystem.
- */
-#if !defined(HAL_USE_EXT) || defined(__DOXYGEN__)
-#define HAL_USE_EXT                 FALSE
-#endif
-
-/**
- * @brief   Enables the GPT subsystem.
- */
-#if !defined(HAL_USE_GPT) || defined(__DOXYGEN__)
-#define HAL_USE_GPT                 TRUE
-#endif
-
-/**
- * @brief   Enables the I2C subsystem.
- */
-#if !defined(HAL_USE_I2C) || defined(__DOXYGEN__)
-#define HAL_USE_I2C                 TRUE
-#endif
-
-/**
- * @brief   Enables the I2S subsystem.
- */
-#if !defined(HAL_USE_I2S) || defined(__DOXYGEN__)
-#define HAL_USE_I2S                 FALSE
-#endif
-
-/**
- * @brief   Enables the ICU subsystem.
- */
-#if !defined(HAL_USE_ICU) || defined(__DOXYGEN__)
-#define HAL_USE_ICU                 FALSE
-#endif
-
-/**
- * @brief   Enables the MAC subsystem.
- */
-#if !defined(HAL_USE_MAC) || defined(__DOXYGEN__)
-#define HAL_USE_MAC                 FALSE
-#endif
-
-/**
- * @brief   Enables the MMC_SPI subsystem.
- */
-#if !defined(HAL_USE_MMC_SPI) || defined(__DOXYGEN__)
-#define HAL_USE_MMC_SPI             FALSE
-#endif
-
-/**
- * @brief   Enables the PWM subsystem.
- */
-#if !defined(HAL_USE_PWM) || defined(__DOXYGEN__)
-#define HAL_USE_PWM                 FALSE
-#endif
-
-/**
- * @brief   Enables the QSPI subsystem.
- */
-#if !defined(HAL_USE_QSPI) || defined(__DOXYGEN__)
-#define HAL_USE_QSPI                FALSE
-#endif
-
-/**
- * @brief   Enables the RTC subsystem.
- */
-#if !defined(HAL_USE_RTC) || defined(__DOXYGEN__)
-#define HAL_USE_RTC                 FALSE
-#endif
-
-/**
- * @brief   Enables the SDC subsystem.
- */
-#if !defined(HAL_USE_SDC) || defined(__DOXYGEN__)
-#define HAL_USE_SDC                 FALSE
-#endif
-
-/**
- * @brief   Enables the SERIAL subsystem.
- */
-#if !defined(HAL_USE_SERIAL) || defined(__DOXYGEN__)
-#define HAL_USE_SERIAL              FALSE
-#endif
-
-/**
- * @brief   Enables the SERIAL over USB subsystem.
- */
-#if !defined(HAL_USE_SERIAL_USB) || defined(__DOXYGEN__)
-#define HAL_USE_SERIAL_USB          FALSE
-#endif
-
-/**
- * @brief   Enables the SPI subsystem.
- */
-#if !defined(HAL_USE_SPI) || defined(__DOXYGEN__)
-#define HAL_USE_SPI                 FALSE
-#endif
-
-/**
- * @brief   Enables the UART subsystem.
- */
-#if !defined(HAL_USE_UART) || defined(__DOXYGEN__)
-#define HAL_USE_UART                FALSE
-#endif
-
-/**
- * @brief   Enables the USB subsystem.
- */
-#if !defined(HAL_USE_USB) || defined(__DOXYGEN__)
-#define HAL_USE_USB                 TRUE
-#endif
-
-/**
- * @brief   Enables the WDG subsystem.
- */
-#if !defined(HAL_USE_WDG) || defined(__DOXYGEN__)
-#define HAL_USE_WDG                 FALSE
-#endif
-
-/*===========================================================================*/
-/* ADC driver related settings.                                              */
-/*===========================================================================*/
-
-/**
- * @brief   Enables synchronous APIs.
- * @note    Disabling this option saves both code and data space.
- */
-#if !defined(ADC_USE_WAIT) || defined(__DOXYGEN__)
-#define ADC_USE_WAIT                TRUE
-#endif
-
-/**
- * @brief   Enables the @p adcAcquireBus() and @p adcReleaseBus() APIs.
- * @note    Disabling this option saves both code and data space.
- */
-#if !defined(ADC_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__)
-#define ADC_USE_MUTUAL_EXCLUSION    TRUE
-#endif
-
-/*===========================================================================*/
-/* CAN driver related settings.                                              */
-/*===========================================================================*/
-
-/**
- * @brief   Sleep mode related APIs inclusion switch.
- */
-#if !defined(CAN_USE_SLEEP_MODE) || defined(__DOXYGEN__)
-#define CAN_USE_SLEEP_MODE          TRUE
-#endif
-
-/*===========================================================================*/
-/* I2C driver related settings.                                              */
-/*===========================================================================*/
-
-/**
- * @brief   Enables the mutual exclusion APIs on the I2C bus.
- */
-#if !defined(I2C_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__)
-#define I2C_USE_MUTUAL_EXCLUSION    TRUE
-#endif
-
-/*===========================================================================*/
-/* MAC driver related settings.                                              */
-/*===========================================================================*/
-
-/**
- * @brief   Enables an event sources for incoming packets.
- */
-#if !defined(MAC_USE_ZERO_COPY) || defined(__DOXYGEN__)
-#define MAC_USE_ZERO_COPY           FALSE
-#endif
-
-/**
- * @brief   Enables an event sources for incoming packets.
- */
-#if !defined(MAC_USE_EVENTS) || defined(__DOXYGEN__)
-#define MAC_USE_EVENTS              TRUE
-#endif
-
-/*===========================================================================*/
-/* MMC_SPI driver related settings.                                          */
-/*===========================================================================*/
-
-/**
- * @brief   Delays insertions.
- * @details If enabled this options inserts delays into the MMC waiting
- *          routines releasing some extra CPU time for the threads with
- *          lower priority, this may slow down the driver a bit however.
- *          This option is recommended also if the SPI driver does not
- *          use a DMA channel and heavily loads the CPU.
- */
-#if !defined(MMC_NICE_WAITING) || defined(__DOXYGEN__)
-#define MMC_NICE_WAITING            TRUE
-#endif
-
-/*===========================================================================*/
-/* SDC driver related settings.                                              */
-/*===========================================================================*/
-
-/**
- * @brief   Number of initialization attempts before rejecting the card.
- * @note    Attempts are performed at 10mS intervals.
- */
-#if !defined(SDC_INIT_RETRY) || defined(__DOXYGEN__)
-#define SDC_INIT_RETRY              100
-#endif
-
-/**
- * @brief   Include support for MMC cards.
- * @note    MMC support is not yet implemented so this option must be kept
- *          at @p FALSE.
- */
-#if !defined(SDC_MMC_SUPPORT) || defined(__DOXYGEN__)
-#define SDC_MMC_SUPPORT             FALSE
-#endif
-
-/**
- * @brief   Delays insertions.
- * @details If enabled this options inserts delays into the MMC waiting
- *          routines releasing some extra CPU time for the threads with
- *          lower priority, this may slow down the driver a bit however.
- */
-#if !defined(SDC_NICE_WAITING) || defined(__DOXYGEN__)
-#define SDC_NICE_WAITING            TRUE
-#endif
-
-/*===========================================================================*/
-/* SERIAL driver related settings.                                           */
-/*===========================================================================*/
-
-/**
- * @brief   Default bit rate.
- * @details Configuration parameter, this is the baud rate selected for the
- *          default configuration.
- */
-#if !defined(SERIAL_DEFAULT_BITRATE) || defined(__DOXYGEN__)
-#define SERIAL_DEFAULT_BITRATE      38400
-#endif
-
-/**
- * @brief   Serial buffers size.
- * @details Configuration parameter, you can change the depth of the queue
- *          buffers depending on the requirements of your application.
- * @note    The default is 16 bytes for both the transmission and receive
- *          buffers.
- */
-#if !defined(SERIAL_BUFFERS_SIZE) || defined(__DOXYGEN__)
-#define SERIAL_BUFFERS_SIZE         16
-#endif
-
-/*===========================================================================*/
-/* SERIAL_USB driver related setting.                                        */
-/*===========================================================================*/
-
-/**
- * @brief   Serial over USB buffers size.
- * @details Configuration parameter, the buffer size must be a multiple of
- *          the USB data endpoint maximum packet size.
- * @note    The default is 256 bytes for both the transmission and receive
- *          buffers.
- */
-#if !defined(SERIAL_USB_BUFFERS_SIZE) || defined(__DOXYGEN__)
-#define SERIAL_USB_BUFFERS_SIZE     1
-#endif
-
-/**
- * @brief   Serial over USB number of buffers.
- * @note    The default is 2 buffers.
- */
-#if !defined(SERIAL_USB_BUFFERS_NUMBER) || defined(__DOXYGEN__)
-#define SERIAL_USB_BUFFERS_NUMBER   2
-#endif
-
-/*===========================================================================*/
-/* SPI driver related settings.                                              */
-/*===========================================================================*/
-
-/**
- * @brief   Enables synchronous APIs.
- * @note    Disabling this option saves both code and data space.
- */
-#if !defined(SPI_USE_WAIT) || defined(__DOXYGEN__)
-#define SPI_USE_WAIT                TRUE
-#endif
-
-/**
- * @brief   Enables the @p spiAcquireBus() and @p spiReleaseBus() APIs.
- * @note    Disabling this option saves both code and data space.
- */
-#if !defined(SPI_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__)
-#define SPI_USE_MUTUAL_EXCLUSION    TRUE
-#endif
-
-/*===========================================================================*/
-/* UART driver related settings.                                             */
-/*===========================================================================*/
-
-/**
- * @brief   Enables synchronous APIs.
- * @note    Disabling this option saves both code and data space.
- */
-#if !defined(UART_USE_WAIT) || defined(__DOXYGEN__)
-#define UART_USE_WAIT               FALSE
-#endif
-
-/**
- * @brief   Enables the @p uartAcquireBus() and @p uartReleaseBus() APIs.
- * @note    Disabling this option saves both code and data space.
- */
-#if !defined(UART_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__)
-#define UART_USE_MUTUAL_EXCLUSION   FALSE
-#endif
-
-/*===========================================================================*/
-/* USB driver related settings.                                              */
-/*===========================================================================*/
-
-/**
- * @brief   Enables synchronous APIs.
- * @note    Disabling this option saves both code and data space.
- */
-#if !defined(USB_USE_WAIT) || defined(__DOXYGEN__)
-#define USB_USE_WAIT                TRUE
-#endif
-
-#endif /* HALCONF_H */
-
-/** @} */

keyboards/dztech/dz40rgb/keymaps/default/keymap.c

@@ -1,5 +1,4 @@
 #include QMK_KEYBOARD_H
-extern bool g_suspend_state;
 #define _LAYER0 0
 #define _LAYER1 1
 #define _LAYER2 2
@@ -32,7 +31,6 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
 
 };
 
-extern led_config_t g_led_config;
 void rgb_matrix_layer_helper (uint8_t red, uint8_t green, uint8_t blue, bool default_layer) {
   for (int i = 0; i < DRIVER_LED_TOTAL; i++) {
     if (HAS_FLAGS(g_led_config.flags[i], LED_FLAG_MODIFIER)) {

keyboards/dztech/dz40rgb/keymaps/split_space/keymap.c

@@ -1,5 +1,4 @@
 #include QMK_KEYBOARD_H
-extern bool g_suspend_state;
 #define _LAYER0 0
 #define _LAYER1 1
 #define _LAYER2 2
@@ -53,7 +52,6 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
 
 
 
-extern led_config_t g_led_config;
 void rgb_matrix_layer_helper (uint8_t red, uint8_t green, uint8_t blue, bool default_layer) {
   for (int i = 0; i < DRIVER_LED_TOTAL; i++) {
     if (HAS_FLAGS(g_led_config.flags[i], LED_FLAG_MODIFIER)) {

keyboards/dztech/dz40rgb/mcuconf.h

@@ -1,257 +0,0 @@
-/*
-    ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio
-
-    Licensed under the Apache License, Version 2.0 (the "License");
-    you may not use this file except in compliance with the License.
-    You may obtain a copy of the License at
-
-        http://www.apache.org/licenses/LICENSE-2.0
-
-    Unless required by applicable law or agreed to in writing, software
-    distributed under the License is distributed on an "AS IS" BASIS,
-    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-    See the License for the specific language governing permissions and
-    limitations under the License.
-*/
-
-#ifndef MCUCONF_H
-#define MCUCONF_H
-
-/*
- * STM32F3xx drivers configuration.
- * The following settings override the default settings present in
- * the various device driver implementation headers.
- * Note that the settings for each driver only have effect if the whole
- * driver is enabled in halconf.h.
- *
- * IRQ priorities:
- * 15...0       Lowest...Highest.
- *
- * DMA priorities:
- * 0...3        Lowest...Highest.
- */
-
-#define STM32F3xx_MCUCONF
-
-/*
- * HAL driver system settings.
- */
-#define STM32_NO_INIT                       FALSE
-#define STM32_PVD_ENABLE                    FALSE
-#define STM32_PLS                           STM32_PLS_LEV0
-#define STM32_HSI_ENABLED                   TRUE
-#define STM32_LSI_ENABLED                   TRUE
-#define STM32_HSE_ENABLED                   TRUE
-#define STM32_LSE_ENABLED                   FALSE
-#define STM32_SW                            STM32_SW_PLL
-#define STM32_PLLSRC                        STM32_PLLSRC_HSE
-#define STM32_PREDIV_VALUE                  1
-#define STM32_PLLMUL_VALUE                  9
-#define STM32_HPRE                          STM32_HPRE_DIV1
-#define STM32_PPRE1                         STM32_PPRE1_DIV2
-#define STM32_PPRE2                         STM32_PPRE2_DIV2
-#define STM32_MCOSEL                        STM32_MCOSEL_NOCLOCK
-#define STM32_ADC12PRES                     STM32_ADC12PRES_DIV1
-#define STM32_ADC34PRES                     STM32_ADC34PRES_DIV1
-#define STM32_USART1SW                      STM32_USART1SW_PCLK
-#define STM32_USART2SW                      STM32_USART2SW_PCLK
-#define STM32_USART3SW                      STM32_USART3SW_PCLK
-#define STM32_UART4SW                       STM32_UART4SW_PCLK
-#define STM32_UART5SW                       STM32_UART5SW_PCLK
-#define STM32_I2C1SW                        STM32_I2C1SW_SYSCLK
-#define STM32_I2C2SW                        STM32_I2C2SW_SYSCLK
-#define STM32_TIM1SW                        STM32_TIM1SW_PCLK2
-#define STM32_TIM8SW                        STM32_TIM8SW_PCLK2
-#define STM32_RTCSEL                        STM32_RTCSEL_LSI
-#define STM32_USB_CLOCK_REQUIRED            TRUE
-#define STM32_USBPRE                        STM32_USBPRE_DIV1P5
-
-#undef STM32_HSE_BYPASS
-// #error "oh no"
-// #endif
-
-/*
- * ADC driver system settings.
- */
-#define STM32_ADC_DUAL_MODE                 FALSE
-#define STM32_ADC_COMPACT_SAMPLES           FALSE
-#define STM32_ADC_USE_ADC1                  FALSE
-#define STM32_ADC_USE_ADC2                  FALSE
-#define STM32_ADC_USE_ADC3                  FALSE
-#define STM32_ADC_USE_ADC4                  FALSE
-#define STM32_ADC_ADC1_DMA_STREAM           STM32_DMA_STREAM_ID(1, 1)
-#define STM32_ADC_ADC2_DMA_STREAM           STM32_DMA_STREAM_ID(2, 1)
-#define STM32_ADC_ADC3_DMA_STREAM           STM32_DMA_STREAM_ID(2, 5)
-#define STM32_ADC_ADC4_DMA_STREAM           STM32_DMA_STREAM_ID(2, 2)
-#define STM32_ADC_ADC1_DMA_PRIORITY         2
-#define STM32_ADC_ADC2_DMA_PRIORITY         2
-#define STM32_ADC_ADC3_DMA_PRIORITY         2
-#define STM32_ADC_ADC4_DMA_PRIORITY         2
-#define STM32_ADC_ADC12_IRQ_PRIORITY        5
-#define STM32_ADC_ADC3_IRQ_PRIORITY         5
-#define STM32_ADC_ADC4_IRQ_PRIORITY         5
-#define STM32_ADC_ADC1_DMA_IRQ_PRIORITY     5
-#define STM32_ADC_ADC2_DMA_IRQ_PRIORITY     5
-#define STM32_ADC_ADC3_DMA_IRQ_PRIORITY     5
-#define STM32_ADC_ADC4_DMA_IRQ_PRIORITY     5
-#define STM32_ADC_ADC12_CLOCK_MODE          ADC_CCR_CKMODE_AHB_DIV1
-#define STM32_ADC_ADC34_CLOCK_MODE          ADC_CCR_CKMODE_AHB_DIV1
-
-/*
- * CAN driver system settings.
- */
-#define STM32_CAN_USE_CAN1                  FALSE
-#define STM32_CAN_CAN1_IRQ_PRIORITY         11
-
-/*
- * DAC driver system settings.
- */
-#define STM32_DAC_DUAL_MODE                 FALSE
-#define STM32_DAC_USE_DAC1_CH1              TRUE
-#define STM32_DAC_USE_DAC1_CH2              TRUE
-#define STM32_DAC_DAC1_CH1_IRQ_PRIORITY     10
-#define STM32_DAC_DAC1_CH2_IRQ_PRIORITY     10
-#define STM32_DAC_DAC1_CH1_DMA_PRIORITY     2
-#define STM32_DAC_DAC1_CH2_DMA_PRIORITY     2
-
-/*
- * EXT driver system settings.
- */
-#define STM32_EXT_EXTI0_IRQ_PRIORITY        6
-#define STM32_EXT_EXTI1_IRQ_PRIORITY        6
-#define STM32_EXT_EXTI2_IRQ_PRIORITY        6
-#define STM32_EXT_EXTI3_IRQ_PRIORITY        6
-#define STM32_EXT_EXTI4_IRQ_PRIORITY        6
-#define STM32_EXT_EXTI5_9_IRQ_PRIORITY      6
-#define STM32_EXT_EXTI10_15_IRQ_PRIORITY    6
-#define STM32_EXT_EXTI16_IRQ_PRIORITY       6
-#define STM32_EXT_EXTI17_IRQ_PRIORITY       6
-#define STM32_EXT_EXTI18_IRQ_PRIORITY       6
-#define STM32_EXT_EXTI19_IRQ_PRIORITY       6
-#define STM32_EXT_EXTI20_IRQ_PRIORITY       6
-#define STM32_EXT_EXTI21_22_29_IRQ_PRIORITY 6
-#define STM32_EXT_EXTI30_32_IRQ_PRIORITY    6
-#define STM32_EXT_EXTI33_IRQ_PRIORITY       6
-
-/*
- * GPT driver system settings.
- */
-#define STM32_GPT_USE_TIM1                  FALSE
-#define STM32_GPT_USE_TIM2                  FALSE
-#define STM32_GPT_USE_TIM3                  FALSE
-#define STM32_GPT_USE_TIM4                  FALSE
-#define STM32_GPT_USE_TIM6                  TRUE
-#define STM32_GPT_USE_TIM7                  TRUE
-#define STM32_GPT_USE_TIM8                  TRUE
-#define STM32_GPT_TIM1_IRQ_PRIORITY         7
-#define STM32_GPT_TIM2_IRQ_PRIORITY         7
-#define STM32_GPT_TIM3_IRQ_PRIORITY         7
-#define STM32_GPT_TIM4_IRQ_PRIORITY         7
-#define STM32_GPT_TIM6_IRQ_PRIORITY         7
-#define STM32_GPT_TIM7_IRQ_PRIORITY         7
-#define STM32_GPT_TIM8_IRQ_PRIORITY         7
-
-/*
- * I2C driver system settings.
- */
-#define STM32_I2C_USE_I2C1                  TRUE
-#define STM32_I2C_USE_I2C2                  FALSE
-#define STM32_I2C_BUSY_TIMEOUT              50
-#define STM32_I2C_I2C1_IRQ_PRIORITY         10
-#define STM32_I2C_I2C2_IRQ_PRIORITY         10
-#define STM32_I2C_USE_DMA                   TRUE
-#define STM32_I2C_I2C1_DMA_PRIORITY         1
-#define STM32_I2C_I2C2_DMA_PRIORITY         1
-#define STM32_I2C_DMA_ERROR_HOOK(i2cp)      osalSysHalt("DMA failure")
-
-/*
- * ICU driver system settings.
- */
-#define STM32_ICU_USE_TIM1                  FALSE
-#define STM32_ICU_USE_TIM2                  FALSE
-#define STM32_ICU_USE_TIM3                  FALSE
-#define STM32_ICU_USE_TIM4                  FALSE
-#define STM32_ICU_USE_TIM8                  FALSE
-#define STM32_ICU_TIM1_IRQ_PRIORITY         7
-#define STM32_ICU_TIM2_IRQ_PRIORITY         7
-#define STM32_ICU_TIM3_IRQ_PRIORITY         7
-#define STM32_ICU_TIM4_IRQ_PRIORITY         7
-#define STM32_ICU_TIM8_IRQ_PRIORITY         7
-
-/*
- * PWM driver system settings.
- */
-#define STM32_PWM_USE_ADVANCED              FALSE
-#define STM32_PWM_USE_TIM1                  FALSE
-#define STM32_PWM_USE_TIM2                  FALSE
-#define STM32_PWM_USE_TIM3                  FALSE
-#define STM32_PWM_USE_TIM4                  FALSE
-#define STM32_PWM_USE_TIM8                  FALSE
-#define STM32_PWM_TIM1_IRQ_PRIORITY         7
-#define STM32_PWM_TIM2_IRQ_PRIORITY         7
-#define STM32_PWM_TIM3_IRQ_PRIORITY         7
-#define STM32_PWM_TIM4_IRQ_PRIORITY         7
-#define STM32_PWM_TIM8_IRQ_PRIORITY         7
-
-/*
- * SERIAL driver system settings.
- */
-#define STM32_SERIAL_USE_USART1             FALSE
-#define STM32_SERIAL_USE_USART2             FALSE
-#define STM32_SERIAL_USE_USART3             FALSE
-#define STM32_SERIAL_USE_UART4              FALSE
-#define STM32_SERIAL_USE_UART5              FALSE
-#define STM32_SERIAL_USART1_PRIORITY        12
-#define STM32_SERIAL_USART2_PRIORITY        12
-#define STM32_SERIAL_USART3_PRIORITY        12
-#define STM32_SERIAL_UART4_PRIORITY         12
-#define STM32_SERIAL_UART5_PRIORITY         12
-
-/*
- * SPI driver system settings.
- */
-#define STM32_SPI_USE_SPI1                  FALSE
-#define STM32_SPI_USE_SPI2                  FALSE
-#define STM32_SPI_USE_SPI3                  FALSE
-#define STM32_SPI_SPI1_DMA_PRIORITY         1
-#define STM32_SPI_SPI2_DMA_PRIORITY         1
-#define STM32_SPI_SPI3_DMA_PRIORITY         1
-#define STM32_SPI_SPI1_IRQ_PRIORITY         10
-#define STM32_SPI_SPI2_IRQ_PRIORITY         10
-#define STM32_SPI_SPI3_IRQ_PRIORITY         10
-#define STM32_SPI_DMA_ERROR_HOOK(spip)      osalSysHalt("DMA failure")
-
-/*
- * ST driver system settings.
- */
-#define STM32_ST_IRQ_PRIORITY               8
-#define STM32_ST_USE_TIMER                  2
-
-/*
- * UART driver system settings.
- */
-#define STM32_UART_USE_USART1               FALSE
-#define STM32_UART_USE_USART2               FALSE
-#define STM32_UART_USE_USART3               FALSE
-#define STM32_UART_USART1_IRQ_PRIORITY      12
-#define STM32_UART_USART2_IRQ_PRIORITY      12
-#define STM32_UART_USART3_IRQ_PRIORITY      12
-#define STM32_UART_USART1_DMA_PRIORITY      0
-#define STM32_UART_USART2_DMA_PRIORITY      0
-#define STM32_UART_USART3_DMA_PRIORITY      0
-#define STM32_UART_DMA_ERROR_HOOK(uartp)    osalSysHalt("DMA failure")
-
-/*
- * USB driver system settings.
- */
-#define STM32_USB_USE_USB1                  TRUE
-#define STM32_USB_LOW_POWER_ON_SUSPEND      FALSE
-#define STM32_USB_USB1_HP_IRQ_PRIORITY      13
-#define STM32_USB_USB1_LP_IRQ_PRIORITY      14
-
-/*
- * WDG driver system settings.
- */
-#define STM32_WDG_USE_IWDG                  FALSE
-
-#endif /* MCUCONF_H */

keyboards/dztech/dz40rgb/rules.mk

@@ -1,50 +1,6 @@
-# project specific files
-
-## chip/board settings
-#   the next two should match the directories in
-#   <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
-MCU_FAMILY = STM32
-MCU_SERIES = STM32F3xx
-
-# Linker script to use
-#   it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
-#   or <this_dir>/ld/
-MCU_LDSCRIPT = STM32F303xC
-
-# Startup code to use
-#  - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/
-MCU_STARTUP = stm32f3xx
-
-# Board: it should exist either in <chibios>/os/hal/boards/
-#  or <this_dir>/boards
-BOARD = GENERIC_STM32_F303XC
-
-# Cortex version
-MCU  = cortex-m4
-
-# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
-ARMV = 7
-
-USE_FPU = yes
-
-# Vector table for application
-# 0x00000000-0x00001000 area is occupied by bootlaoder.*/
-# The CORTEX_VTOR... is needed only for MCHCK/Infinity KB
-# OPT_DEFS = -DCORTEX_VTOR_INIT=0x08005000
-OPT_DEFS =
-
-# Do not put the microcontroller into power saving mode
-# when we get USB suspend event. We want it to keep updating
-# backlight effects.
-OPT_DEFS += -DNO_SUSPEND_POWER_DOWN
-
-# Options to pass to dfu-util when flashing
+MCU  = STM32F303
 DFU_ARGS = -d 0483:df11 -a 0 -s 0x08000000:leave
 DFU_SUFFIX_ARGS = -p DF11 -v 0483
-
-# Build Options
-#   comment out to disable the options.
-#
 BACKLIGHT_ENABLE = no
 BOOTMAGIC_ENABLE = lite            # Virtual DIP switch configuration
 MOUSEKEY_ENABLE = yes              # Mouse keys

keyboards/dztech/dz60rgb/bootloader_defs.h

@@ -1,7 +0,0 @@
-/* Address for jumping to bootloader on STM32 chips. */
-/* It is chip dependent, the correct number can be looked up here:
- * http://www.st.com/web/en/resource/technical/document/application_note/CD00167594.pdf
- * This also requires a patch to chibios:
- *  <tmk_dir>/tmk_core/tool/chibios/ch-bootloader-jump.patch
- */
-#define STM32_BOOTLOADER_ADDRESS 0x1FFFD800

keyboards/dztech/dz60rgb/chconf.h

@@ -1,520 +0,0 @@
-/*
-    ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio
-
-    Licensed under the Apache License, Version 2.0 (the "License");
-    you may not use this file except in compliance with the License.
-    You may obtain a copy of the License at
-
-        http://www.apache.org/licenses/LICENSE-2.0
-
-    Unless required by applicable law or agreed to in writing, software
-    distributed under the License is distributed on an "AS IS" BASIS,
-    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-    See the License for the specific language governing permissions and
-    limitations under the License.
-*/
-
-/**
- * @file    templates/chconf.h
- * @brief   Configuration file template.
- * @details A copy of this file must be placed in each project directory, it
- *          contains the application specific kernel settings.
- *
- * @addtogroup config
- * @details Kernel related settings and hooks.
- * @{
- */
-
-#ifndef CHCONF_H
-#define CHCONF_H
-
-#define _CHIBIOS_RT_CONF_
-
-/*===========================================================================*/
-/**
- * @name System timers settings
- * @{
- */
-/*===========================================================================*/
-
-/**
- * @brief   System time counter resolution.
- * @note    Allowed values are 16 or 32 bits.
- */
-#define CH_CFG_ST_RESOLUTION                32
-
-/**
- * @brief   System tick frequency.
- * @details Frequency of the system timer that drives the system ticks. This
- *          setting also defines the system tick time unit.
- */
-#define CH_CFG_ST_FREQUENCY                 100000
-
-/**
- * @brief   Time delta constant for the tick-less mode.
- * @note    If this value is zero then the system uses the classic
- *          periodic tick. This value represents the minimum number
- *          of ticks that is safe to specify in a timeout directive.
- *          The value one is not valid, timeouts are rounded up to
- *          this value.
- */
-#define CH_CFG_ST_TIMEDELTA                 2
-
-/** @} */
-
-/*===========================================================================*/
-/**
- * @name Kernel parameters and options
- * @{
- */
-/*===========================================================================*/
-
-/**
- * @brief   Round robin interval.
- * @details This constant is the number of system ticks allowed for the
- *          threads before preemption occurs. Setting this value to zero
- *          disables the preemption for threads with equal priority and the
- *          round robin becomes cooperative. Note that higher priority
- *          threads can still preempt, the kernel is always preemptive.
- * @note    Disabling the round robin preemption makes the kernel more compact
- *          and generally faster.
- * @note    The round robin preemption is not supported in tickless mode and
- *          must be set to zero in that case.
- */
-#define CH_CFG_TIME_QUANTUM                 0
-
-/**
- * @brief   Managed RAM size.
- * @details Size of the RAM area to be managed by the OS. If set to zero
- *          then the whole available RAM is used. The core memory is made
- *          available to the heap allocator and/or can be used directly through
- *          the simplified core memory allocator.
- *
- * @note    In order to let the OS manage the whole RAM the linker script must
- *          provide the @p __heap_base__ and @p __heap_end__ symbols.
- * @note    Requires @p CH_CFG_USE_MEMCORE.
- */
-#define CH_CFG_MEMCORE_SIZE                 0
-
-/**
- * @brief   Idle thread automatic spawn suppression.
- * @details When this option is activated the function @p chSysInit()
- *          does not spawn the idle thread. The application @p main()
- *          function becomes the idle thread and must implement an
- *          infinite loop.
- */
-#define CH_CFG_NO_IDLE_THREAD               FALSE
-
-/** @} */
-
-/*===========================================================================*/
-/**
- * @name Performance options
- * @{
- */
-/*===========================================================================*/
-
-/**
- * @brief   OS optimization.
- * @details If enabled then time efficient rather than space efficient code
- *          is used when two possible implementations exist.
- *
- * @note    This is not related to the compiler optimization options.
- * @note    The default is @p TRUE.
- */
-#define CH_CFG_OPTIMIZE_SPEED               TRUE
-
-/** @} */
-
-/*===========================================================================*/
-/**
- * @name Subsystem options
- * @{
- */
-/*===========================================================================*/
-
-/**
- * @brief   Time Measurement APIs.
- * @details If enabled then the time measurement APIs are included in
- *          the kernel.
- *
- * @note    The default is @p TRUE.
- */
-#define CH_CFG_USE_TM                       TRUE
-
-/**
- * @brief   Threads registry APIs.
- * @details If enabled then the registry APIs are included in the kernel.
- *
- * @note    The default is @p TRUE.
- */
-#define CH_CFG_USE_REGISTRY                 TRUE
-
-/**
- * @brief   Threads synchronization APIs.
- * @details If enabled then the @p chThdWait() function is included in
- *          the kernel.
- *
- * @note    The default is @p TRUE.
- */
-#define CH_CFG_USE_WAITEXIT                 TRUE
-
-/**
- * @brief   Semaphores APIs.
- * @details If enabled then the Semaphores APIs are included in the kernel.
- *
- * @note    The default is @p TRUE.
- */
-#define CH_CFG_USE_SEMAPHORES               TRUE
-
-/**
- * @brief   Semaphores queuing mode.
- * @details If enabled then the threads are enqueued on semaphores by
- *          priority rather than in FIFO order.
- *
- * @note    The default is @p FALSE. Enable this if you have special
- *          requirements.
- * @note    Requires @p CH_CFG_USE_SEMAPHORES.
- */
-#define CH_CFG_USE_SEMAPHORES_PRIORITY      FALSE
-
-/**
- * @brief   Mutexes APIs.
- * @details If enabled then the mutexes APIs are included in the kernel.
- *
- * @note    The default is @p TRUE.
- */
-#define CH_CFG_USE_MUTEXES                  TRUE
-
-/**
- * @brief   Enables recursive behavior on mutexes.
- * @note    Recursive mutexes are heavier and have an increased
- *          memory footprint.
- *
- * @note    The default is @p FALSE.
- * @note    Requires @p CH_CFG_USE_MUTEXES.
- */
-#define CH_CFG_USE_MUTEXES_RECURSIVE        FALSE
-
-/**
- * @brief   Conditional Variables APIs.
- * @details If enabled then the conditional variables APIs are included
- *          in the kernel.
- *
- * @note    The default is @p TRUE.
- * @note    Requires @p CH_CFG_USE_MUTEXES.
- */
-#define CH_CFG_USE_CONDVARS                 TRUE
-
-/**
- * @brief   Conditional Variables APIs with timeout.
- * @details If enabled then the conditional variables APIs with timeout
- *          specification are included in the kernel.
- *
- * @note    The default is @p TRUE.
- * @note    Requires @p CH_CFG_USE_CONDVARS.
- */
-#define CH_CFG_USE_CONDVARS_TIMEOUT         TRUE
-
-/**
- * @brief   Events Flags APIs.
- * @details If enabled then the event flags APIs are included in the kernel.
- *
- * @note    The default is @p TRUE.
- */
-#define CH_CFG_USE_EVENTS                   TRUE
-
-/**
- * @brief   Events Flags APIs with timeout.
- * @details If enabled then the events APIs with timeout specification
- *          are included in the kernel.
- *
- * @note    The default is @p TRUE.
- * @note    Requires @p CH_CFG_USE_EVENTS.
- */
-#define CH_CFG_USE_EVENTS_TIMEOUT           TRUE
-
-/**
- * @brief   Synchronous Messages APIs.
- * @details If enabled then the synchronous messages APIs are included
- *          in the kernel.
- *
- * @note    The default is @p TRUE.
- */
-#define CH_CFG_USE_MESSAGES                 TRUE
-
-/**
- * @brief   Synchronous Messages queuing mode.
- * @details If enabled then messages are served by priority rather than in
- *          FIFO order.
- *
- * @note    The default is @p FALSE. Enable this if you have special
- *          requirements.
- * @note    Requires @p CH_CFG_USE_MESSAGES.
- */
-#define CH_CFG_USE_MESSAGES_PRIORITY        TRUE
-
-/**
- * @brief   Mailboxes APIs.
- * @details If enabled then the asynchronous messages (mailboxes) APIs are
- *          included in the kernel.
- *
- * @note    The default is @p TRUE.
- * @note    Requires @p CH_CFG_USE_SEMAPHORES.
- */
-#define CH_CFG_USE_MAILBOXES                TRUE
-
-/**
- * @brief   Core Memory Manager APIs.
- * @details If enabled then the core memory manager APIs are included
- *          in the kernel.
- *
- * @note    The default is @p TRUE.
- */
-#define CH_CFG_USE_MEMCORE                  TRUE
-
-/**
- * @brief   Heap Allocator APIs.
- * @details If enabled then the memory heap allocator APIs are included
- *          in the kernel.
- *
- * @note    The default is @p TRUE.
- * @note    Requires @p CH_CFG_USE_MEMCORE and either @p CH_CFG_USE_MUTEXES or
- *          @p CH_CFG_USE_SEMAPHORES.
- * @note    Mutexes are recommended.
- */
-#define CH_CFG_USE_HEAP                     TRUE
-
-/**
- * @brief   Memory Pools Allocator APIs.
- * @details If enabled then the memory pools allocator APIs are included
- *          in the kernel.
- *
- * @note    The default is @p TRUE.
- */
-#define CH_CFG_USE_MEMPOOLS                 TRUE
-
-/**
- * @brief   Dynamic Threads APIs.
- * @details If enabled then the dynamic threads creation APIs are included
- *          in the kernel.
- *
- * @note    The default is @p TRUE.
- * @note    Requires @p CH_CFG_USE_WAITEXIT.
- * @note    Requires @p CH_CFG_USE_HEAP and/or @p CH_CFG_USE_MEMPOOLS.
- */
-#define CH_CFG_USE_DYNAMIC                  TRUE
-
-/** @} */
-
-/*===========================================================================*/
-/**
- * @name Debug options
- * @{
- */
-/*===========================================================================*/
-
-/**
- * @brief   Debug option, kernel statistics.
- *
- * @note    The default is @p FALSE.
- */
-#define CH_DBG_STATISTICS                   FALSE
-
-/**
- * @brief   Debug option, system state check.
- * @details If enabled the correct call protocol for system APIs is checked
- *          at runtime.
- *
- * @note    The default is @p FALSE.
- */
-#define CH_DBG_SYSTEM_STATE_CHECK           FALSE
-
-/**
- * @brief   Debug option, parameters checks.
- * @details If enabled then the checks on the API functions input
- *          parameters are activated.
- *
- * @note    The default is @p FALSE.
- */
-#define CH_DBG_ENABLE_CHECKS                FALSE
-
-/**
- * @brief   Debug option, consistency checks.
- * @details If enabled then all the assertions in the kernel code are
- *          activated. This includes consistency checks inside the kernel,
- *          runtime anomalies and port-defined checks.
- *
- * @note    The default is @p FALSE.
- */
-#define CH_DBG_ENABLE_ASSERTS               FALSE
-
-/**
- * @brief   Debug option, trace buffer.
- * @details If enabled then the trace buffer is activated.
- *
- * @note    The default is @p CH_DBG_TRACE_MASK_DISABLED.
- */
-#define CH_DBG_TRACE_MASK                   CH_DBG_TRACE_MASK_DISABLED
-
-/**
- * @brief   Trace buffer entries.
- * @note    The trace buffer is only allocated if @p CH_DBG_TRACE_MASK is
- *          different from @p CH_DBG_TRACE_MASK_DISABLED.
- */
-#define CH_DBG_TRACE_BUFFER_SIZE            128
-
-/**
- * @brief   Debug option, stack checks.
- * @details If enabled then a runtime stack check is performed.
- *
- * @note    The default is @p FALSE.
- * @note    The stack check is performed in a architecture/port dependent way.
- *          It may not be implemented or some ports.
- * @note    The default failure mode is to halt the system with the global
- *          @p panic_msg variable set to @p NULL.
- */
-#define CH_DBG_ENABLE_STACK_CHECK           TRUE
-
-/**
- * @brief   Debug option, stacks initialization.
- * @details If enabled then the threads working area is filled with a byte
- *          value when a thread is created. This can be useful for the
- *          runtime measurement of the used stack.
- *
- * @note    The default is @p FALSE.
- */
-#define CH_DBG_FILL_THREADS                 FALSE
-
-/**
- * @brief   Debug option, threads profiling.
- * @details If enabled then a field is added to the @p thread_t structure that
- *          counts the system ticks occurred while executing the thread.
- *
- * @note    The default is @p FALSE.
- * @note    This debug option is not currently compatible with the
- *          tickless mode.
- */
-#define CH_DBG_THREADS_PROFILING            FALSE
-
-/** @} */
-
-/*===========================================================================*/
-/**
- * @name Kernel hooks
- * @{
- */
-/*===========================================================================*/
-
-/**
- * @brief   Threads descriptor structure extension.
- * @details User fields added to the end of the @p thread_t structure.
- */
-#define CH_CFG_THREAD_EXTRA_FIELDS                                          \
-  /* Add threads custom fields here.*/
-
-/**
- * @brief   Threads initialization hook.
- * @details User initialization code added to the @p chThdInit() API.
- *
- * @note    It is invoked from within @p chThdInit() and implicitly from all
- *          the threads creation APIs.
- */
-#define CH_CFG_THREAD_INIT_HOOK(tp) {                                       \
-  /* Add threads initialization code here.*/                                \
-}
-
-/**
- * @brief   Threads finalization hook.
- * @details User finalization code added to the @p chThdExit() API.
- */
-#define CH_CFG_THREAD_EXIT_HOOK(tp) {                                       \
-  /* Add threads finalization code here.*/                                  \
-}
-
-/**
- * @brief   Context switch hook.
- * @details This hook is invoked just before switching between threads.
- */
-#define CH_CFG_CONTEXT_SWITCH_HOOK(ntp, otp) {                              \
-  /* Context switch code here.*/                                            \
-}
-
-/**
- * @brief   ISR enter hook.
- */
-#define CH_CFG_IRQ_PROLOGUE_HOOK() {                                        \
-  /* IRQ prologue code here.*/                                              \
-}
-
-/**
- * @brief   ISR exit hook.
- */
-#define CH_CFG_IRQ_EPILOGUE_HOOK() {                                        \
-  /* IRQ epilogue code here.*/                                              \
-}
-
-/**
- * @brief   Idle thread enter hook.
- * @note    This hook is invoked within a critical zone, no OS functions
- *          should be invoked from here.
- * @note    This macro can be used to activate a power saving mode.
- */
-#define CH_CFG_IDLE_ENTER_HOOK() {                                          \
-  /* Idle-enter code here.*/                                                \
-}
-
-/**
- * @brief   Idle thread leave hook.
- * @note    This hook is invoked within a critical zone, no OS functions
- *          should be invoked from here.
- * @note    This macro can be used to deactivate a power saving mode.
- */
-#define CH_CFG_IDLE_LEAVE_HOOK() {                                          \
-  /* Idle-leave code here.*/                                                \
-}
-
-/**
- * @brief   Idle Loop hook.
- * @details This hook is continuously invoked by the idle thread loop.
- */
-#define CH_CFG_IDLE_LOOP_HOOK() {                                           \
-  /* Idle loop code here.*/                                                 \
-}
-
-/**
- * @brief   System tick event hook.
- * @details This hook is invoked in the system tick handler immediately
- *          after processing the virtual timers queue.
- */
-#define CH_CFG_SYSTEM_TICK_HOOK() {                                         \
-  /* System tick event code here.*/                                         \
-}
-
-/**
- * @brief   System halt hook.
- * @details This hook is invoked in case to a system halting error before
- *          the system is halted.
- */
-#define CH_CFG_SYSTEM_HALT_HOOK(reason) {                                   \
-  /* System halt code here.*/                                               \
-}
-
-/**
- * @brief   Trace hook.
- * @details This hook is invoked each time a new record is written in the
- *          trace buffer.
- */
-#define CH_CFG_TRACE_HOOK(tep) {                                            \
-  /* Trace code here.*/                                                     \
-}
-
-/** @} */
-
-/*===========================================================================*/
-/* Port-specific settings (override port settings defaulted in chcore.h).    */
-/*===========================================================================*/
-
-#endif  /* CHCONF_H */
-
-/** @} */

keyboards/dztech/dz60rgb/config.h

@@ -32,5 +32,11 @@
 #define DRIVER_ADDR_1 0b1010000
 #define DRIVER_ADDR_2 0b1010000 // this is here for compliancy reasons.
 #define DRIVER_COUNT 2
+#if defined (dzrgb60_ansi) || defined (dzrgb60_iso)
+#define DRIVER_1_LED_TOTAL 61
+#elif defined (dzrgb60_hhkb) || defined (dzrgb60_hhkb_iso)
+#define DRIVER_1_LED_TOTAL 62
+#else
 #define DRIVER_1_LED_TOTAL 63
+#endif
 #define DRIVER_LED_TOTAL DRIVER_1_LED_TOTAL

keyboards/dztech/dz60rgb/halconf.h

@@ -1,388 +0,0 @@
-/*
-    ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio
-
-    Licensed under the Apache License, Version 2.0 (the "License");
-    you may not use this file except in compliance with the License.
-    You may obtain a copy of the License at
-
-        http://www.apache.org/licenses/LICENSE-2.0
-
-    Unless required by applicable law or agreed to in writing, software
-    distributed under the License is distributed on an "AS IS" BASIS,
-    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-    See the License for the specific language governing permissions and
-    limitations under the License.
-*/
-
-/**
- * @file    templates/halconf.h
- * @brief   HAL configuration header.
- * @details HAL configuration file, this file allows to enable or disable the
- *          various device drivers from your application. You may also use
- *          this file in order to override the device drivers default settings.
- *
- * @addtogroup HAL_CONF
- * @{
- */
-
-#ifndef HALCONF_H
-#define HALCONF_H
-
-#include "mcuconf.h"
-
-/**
- * @brief   Enables the PAL subsystem.
- */
-#if !defined(HAL_USE_PAL) || defined(__DOXYGEN__)
-#define HAL_USE_PAL                 TRUE
-#endif
-
-/**
- * @brief   Enables the ADC subsystem.
- */
-#if !defined(HAL_USE_ADC) || defined(__DOXYGEN__)
-#define HAL_USE_ADC                 FALSE
-#endif
-
-/**
- * @brief   Enables the CAN subsystem.
- */
-#if !defined(HAL_USE_CAN) || defined(__DOXYGEN__)
-#define HAL_USE_CAN                 FALSE
-#endif
-
-/**
- * @brief   Enables the DAC subsystem.
- */
-#if !defined(HAL_USE_DAC) || defined(__DOXYGEN__)
-#define HAL_USE_DAC                 TRUE
-#endif
-
-/**
- * @brief   Enables the EXT subsystem.
- */
-#if !defined(HAL_USE_EXT) || defined(__DOXYGEN__)
-#define HAL_USE_EXT                 FALSE
-#endif
-
-/**
- * @brief   Enables the GPT subsystem.
- */
-#if !defined(HAL_USE_GPT) || defined(__DOXYGEN__)
-#define HAL_USE_GPT                 TRUE
-#endif
-
-/**
- * @brief   Enables the I2C subsystem.
- */
-#if !defined(HAL_USE_I2C) || defined(__DOXYGEN__)
-#define HAL_USE_I2C                 TRUE
-#endif
-
-/**
- * @brief   Enables the I2S subsystem.
- */
-#if !defined(HAL_USE_I2S) || defined(__DOXYGEN__)
-#define HAL_USE_I2S                 FALSE
-#endif
-
-/**
- * @brief   Enables the ICU subsystem.
- */
-#if !defined(HAL_USE_ICU) || defined(__DOXYGEN__)
-#define HAL_USE_ICU                 FALSE
-#endif
-
-/**
- * @brief   Enables the MAC subsystem.
- */
-#if !defined(HAL_USE_MAC) || defined(__DOXYGEN__)
-#define HAL_USE_MAC                 FALSE
-#endif
-
-/**
- * @brief   Enables the MMC_SPI subsystem.
- */
-#if !defined(HAL_USE_MMC_SPI) || defined(__DOXYGEN__)
-#define HAL_USE_MMC_SPI             FALSE
-#endif
-
-/**
- * @brief   Enables the PWM subsystem.
- */
-#if !defined(HAL_USE_PWM) || defined(__DOXYGEN__)
-#define HAL_USE_PWM                 FALSE
-#endif
-
-/**
- * @brief   Enables the QSPI subsystem.
- */
-#if !defined(HAL_USE_QSPI) || defined(__DOXYGEN__)
-#define HAL_USE_QSPI                FALSE
-#endif
-
-/**
- * @brief   Enables the RTC subsystem.
- */
-#if !defined(HAL_USE_RTC) || defined(__DOXYGEN__)
-#define HAL_USE_RTC                 FALSE
-#endif
-
-/**
- * @brief   Enables the SDC subsystem.
- */
-#if !defined(HAL_USE_SDC) || defined(__DOXYGEN__)
-#define HAL_USE_SDC                 FALSE
-#endif
-
-/**
- * @brief   Enables the SERIAL subsystem.
- */
-#if !defined(HAL_USE_SERIAL) || defined(__DOXYGEN__)
-#define HAL_USE_SERIAL              FALSE
-#endif
-
-/**
- * @brief   Enables the SERIAL over USB subsystem.
- */
-#if !defined(HAL_USE_SERIAL_USB) || defined(__DOXYGEN__)
-#define HAL_USE_SERIAL_USB          FALSE
-#endif
-
-/**
- * @brief   Enables the SPI subsystem.
- */
-#if !defined(HAL_USE_SPI) || defined(__DOXYGEN__)
-#define HAL_USE_SPI                 FALSE
-#endif
-
-/**
- * @brief   Enables the UART subsystem.
- */
-#if !defined(HAL_USE_UART) || defined(__DOXYGEN__)
-#define HAL_USE_UART                FALSE
-#endif
-
-/**
- * @brief   Enables the USB subsystem.
- */
-#if !defined(HAL_USE_USB) || defined(__DOXYGEN__)
-#define HAL_USE_USB                 TRUE
-#endif
-
-/**
- * @brief   Enables the WDG subsystem.
- */
-#if !defined(HAL_USE_WDG) || defined(__DOXYGEN__)
-#define HAL_USE_WDG                 FALSE
-#endif
-
-/*===========================================================================*/
-/* ADC driver related settings.                                              */
-/*===========================================================================*/
-
-/**
- * @brief   Enables synchronous APIs.
- * @note    Disabling this option saves both code and data space.
- */
-#if !defined(ADC_USE_WAIT) || defined(__DOXYGEN__)
-#define ADC_USE_WAIT                TRUE
-#endif
-
-/**
- * @brief   Enables the @p adcAcquireBus() and @p adcReleaseBus() APIs.
- * @note    Disabling this option saves both code and data space.
- */
-#if !defined(ADC_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__)
-#define ADC_USE_MUTUAL_EXCLUSION    TRUE
-#endif
-
-/*===========================================================================*/
-/* CAN driver related settings.                                              */
-/*===========================================================================*/
-
-/**
- * @brief   Sleep mode related APIs inclusion switch.
- */
-#if !defined(CAN_USE_SLEEP_MODE) || defined(__DOXYGEN__)
-#define CAN_USE_SLEEP_MODE          TRUE
-#endif
-
-/*===========================================================================*/
-/* I2C driver related settings.                                              */
-/*===========================================================================*/
-
-/**
- * @brief   Enables the mutual exclusion APIs on the I2C bus.
- */
-#if !defined(I2C_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__)
-#define I2C_USE_MUTUAL_EXCLUSION    TRUE
-#endif
-
-/*===========================================================================*/
-/* MAC driver related settings.                                              */
-/*===========================================================================*/
-
-/**
- * @brief   Enables an event sources for incoming packets.
- */
-#if !defined(MAC_USE_ZERO_COPY) || defined(__DOXYGEN__)
-#define MAC_USE_ZERO_COPY           FALSE
-#endif
-
-/**
- * @brief   Enables an event sources for incoming packets.
- */
-#if !defined(MAC_USE_EVENTS) || defined(__DOXYGEN__)
-#define MAC_USE_EVENTS              TRUE
-#endif
-
-/*===========================================================================*/
-/* MMC_SPI driver related settings.                                          */
-/*===========================================================================*/
-
-/**
- * @brief   Delays insertions.
- * @details If enabled this options inserts delays into the MMC waiting
- *          routines releasing some extra CPU time for the threads with
- *          lower priority, this may slow down the driver a bit however.
- *          This option is recommended also if the SPI driver does not
- *          use a DMA channel and heavily loads the CPU.
- */
-#if !defined(MMC_NICE_WAITING) || defined(__DOXYGEN__)
-#define MMC_NICE_WAITING            TRUE
-#endif
-
-/*===========================================================================*/
-/* SDC driver related settings.                                              */
-/*===========================================================================*/
-
-/**
- * @brief   Number of initialization attempts before rejecting the card.
- * @note    Attempts are performed at 10mS intervals.
- */
-#if !defined(SDC_INIT_RETRY) || defined(__DOXYGEN__)
-#define SDC_INIT_RETRY              100
-#endif
-
-/**
- * @brief   Include support for MMC cards.
- * @note    MMC support is not yet implemented so this option must be kept
- *          at @p FALSE.
- */
-#if !defined(SDC_MMC_SUPPORT) || defined(__DOXYGEN__)
-#define SDC_MMC_SUPPORT             FALSE
-#endif
-
-/**
- * @brief   Delays insertions.
- * @details If enabled this options inserts delays into the MMC waiting
- *          routines releasing some extra CPU time for the threads with
- *          lower priority, this may slow down the driver a bit however.
- */
-#if !defined(SDC_NICE_WAITING) || defined(__DOXYGEN__)
-#define SDC_NICE_WAITING            TRUE
-#endif
-
-/*===========================================================================*/
-/* SERIAL driver related settings.                                           */
-/*===========================================================================*/
-
-/**
- * @brief   Default bit rate.
- * @details Configuration parameter, this is the baud rate selected for the
- *          default configuration.
- */
-#if !defined(SERIAL_DEFAULT_BITRATE) || defined(__DOXYGEN__)
-#define SERIAL_DEFAULT_BITRATE      38400
-#endif
-
-/**
- * @brief   Serial buffers size.
- * @details Configuration parameter, you can change the depth of the queue
- *          buffers depending on the requirements of your application.
- * @note    The default is 16 bytes for both the transmission and receive
- *          buffers.
- */
-#if !defined(SERIAL_BUFFERS_SIZE) || defined(__DOXYGEN__)
-#define SERIAL_BUFFERS_SIZE         16
-#endif
-
-/*===========================================================================*/
-/* SERIAL_USB driver related setting.                                        */
-/*===========================================================================*/
-
-/**
- * @brief   Serial over USB buffers size.
- * @details Configuration parameter, the buffer size must be a multiple of
- *          the USB data endpoint maximum packet size.
- * @note    The default is 256 bytes for both the transmission and receive
- *          buffers.
- */
-#if !defined(SERIAL_USB_BUFFERS_SIZE) || defined(__DOXYGEN__)
-#define SERIAL_USB_BUFFERS_SIZE     1
-#endif
-
-/**
- * @brief   Serial over USB number of buffers.
- * @note    The default is 2 buffers.
- */
-#if !defined(SERIAL_USB_BUFFERS_NUMBER) || defined(__DOXYGEN__)
-#define SERIAL_USB_BUFFERS_NUMBER   2
-#endif
-
-/*===========================================================================*/
-/* SPI driver related settings.                                              */
-/*===========================================================================*/
-
-/**
- * @brief   Enables synchronous APIs.
- * @note    Disabling this option saves both code and data space.
- */
-#if !defined(SPI_USE_WAIT) || defined(__DOXYGEN__)
-#define SPI_USE_WAIT                TRUE
-#endif
-
-/**
- * @brief   Enables the @p spiAcquireBus() and @p spiReleaseBus() APIs.
- * @note    Disabling this option saves both code and data space.
- */
-#if !defined(SPI_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__)
-#define SPI_USE_MUTUAL_EXCLUSION    TRUE
-#endif
-
-/*===========================================================================*/
-/* UART driver related settings.                                             */
-/*===========================================================================*/
-
-/**
- * @brief   Enables synchronous APIs.
- * @note    Disabling this option saves both code and data space.
- */
-#if !defined(UART_USE_WAIT) || defined(__DOXYGEN__)
-#define UART_USE_WAIT               FALSE
-#endif
-
-/**
- * @brief   Enables the @p uartAcquireBus() and @p uartReleaseBus() APIs.
- * @note    Disabling this option saves both code and data space.
- */
-#if !defined(UART_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__)
-#define UART_USE_MUTUAL_EXCLUSION   FALSE
-#endif
-
-/*===========================================================================*/
-/* USB driver related settings.                                              */
-/*===========================================================================*/
-
-/**
- * @brief   Enables synchronous APIs.
- * @note    Disabling this option saves both code and data space.
- */
-#if !defined(USB_USE_WAIT) || defined(__DOXYGEN__)
-#define USB_USE_WAIT                TRUE
-#endif
-
-#endif /* HALCONF_H */
-
-/** @} */

keyboards/dztech/dz60rgb/keymaps/ansi/config.h

@@ -1,6 +1,2 @@
 #pragma once
 #define dzrgb60_ansi
-#undef DRIVER_1_LED_TOTAL
-#undef DRIVER_LED_TOTAL
-#define DRIVER_1_LED_TOTAL 61
-#define DRIVER_LED_TOTAL DRIVER_1_LED_TOTAL

keyboards/dztech/dz60rgb/keymaps/ansi/keymap.c

@@ -1,5 +1,4 @@
 #include QMK_KEYBOARD_H
-extern bool g_suspend_state;
 #define _LAYER0 0
 #define _LAYER1 1
 #define _LAYER2 2
@@ -38,7 +37,6 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
 				KC_TRNS,  KC_TRNS,  KC_TRNS,                      TO(0),                                  KC_TRNS,  KC_TRNS,  KC_TRNS,            KC_TRNS),
 		};
 
-extern led_config_t g_led_config;
 void rgb_matrix_layer_helper (uint8_t red, uint8_t green, uint8_t blue, bool default_layer) {
   for (int i = 0; i < DRIVER_LED_TOTAL; i++) {
     if (HAS_FLAGS(g_led_config.flags[i], LED_FLAG_MODIFIER)) {

keyboards/dztech/dz60rgb/keymaps/default/keymap.c

@@ -1,5 +1,4 @@
 #include QMK_KEYBOARD_H
-extern bool g_suspend_state;
 #define _LAYER0 0
 #define _LAYER1 1
 #define _LAYER2 2

keyboards/dztech/dz60rgb/keymaps/hhkb/config.h

@@ -1,6 +1,2 @@
 #pragma once
 #define dzrgb60_hhkb
-#undef DRIVER_1_LED_TOTAL
-#undef DRIVER_LED_TOTAL
-#define DRIVER_1_LED_TOTAL 62
-#define DRIVER_LED_TOTAL DRIVER_1_LED_TOTAL

keyboards/dztech/dz60rgb/keymaps/hhkb/keymap.c

@@ -1,5 +1,4 @@
 #include QMK_KEYBOARD_H
-extern bool g_suspend_state;
 #define _LAYER0 0
 #define _LAYER1 1
 #define _LAYER2 2
@@ -39,7 +38,6 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
 		};
 
 
-extern led_config_t g_led_config;
 void rgb_matrix_layer_helper (uint8_t red, uint8_t green, uint8_t blue, bool default_layer) {
   for (int i = 0; i < DRIVER_LED_TOTAL; i++) {
     if (HAS_FLAGS(g_led_config.flags[i], LED_FLAG_MODIFIER)) {

keyboards/dztech/dz60rgb/keymaps/hhkb_iso/config.h

@@ -1,6 +1,2 @@
 #pragma once
 #define dzrgb60_hhkb_iso
-#undef DRIVER_1_LED_TOTAL
-#undef DRIVER_LED_TOTAL
-#define DRIVER_1_LED_TOTAL 62
-#define DRIVER_LED_TOTAL DRIVER_1_LED_TOTAL

keyboards/dztech/dz60rgb/keymaps/hhkb_iso/keymap.c

@@ -1,5 +1,4 @@
 #include QMK_KEYBOARD_H
-extern bool g_suspend_state;
 #define _LAYER0 0
 #define _LAYER1 1
 #define _LAYER2 2
@@ -39,7 +38,6 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
 				  KC_TRNS,  KC_TRNS,  KC_TRNS,                      TO(0),                                            KC_TRNS,  KC_TRNS,            KC_TRNS),
 		};
 
-extern led_config_t g_led_config;
 void rgb_matrix_layer_helper (uint8_t red, uint8_t green, uint8_t blue, bool default_layer) {
   for (int i = 0; i < DRIVER_LED_TOTAL; i++) {
     if (HAS_FLAGS(g_led_config.flags[i], LED_FLAG_MODIFIER)) {

keyboards/dztech/dz60rgb/keymaps/iso/config.h

@@ -1,6 +1,2 @@
 #pragma once
 #define dzrgb60_iso
-#undef DRIVER_1_LED_TOTAL
-#undef DRIVER_LED_TOTAL
-#define DRIVER_1_LED_TOTAL 61
-#define DRIVER_LED_TOTAL DRIVER_1_LED_TOTAL

keyboards/dztech/dz60rgb/keymaps/iso/keymap.c

@@ -1,5 +1,4 @@
 #include QMK_KEYBOARD_H
-extern bool g_suspend_state;
 #define _LAYER0 0
 #define _LAYER1 1
 #define _LAYER2 2
@@ -38,7 +37,6 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
 				KC_TRNS,  KC_TRNS,  KC_TRNS,                      TO(0),                                  KC_TRNS,  KC_TRNS,  KC_TRNS,            KC_TRNS),
 		};
 
-extern led_config_t g_led_config;
 void rgb_matrix_layer_helper (uint8_t red, uint8_t green, uint8_t blue, bool default_layer) {
   for (int i = 0; i < DRIVER_LED_TOTAL; i++) {
     if (HAS_FLAGS(g_led_config.flags[i], LED_FLAG_MODIFIER)) {

keyboards/dztech/dz60rgb/keymaps/matthewrobo/keymap.c

@@ -1,6 +1,5 @@
 #include QMK_KEYBOARD_H
 
-extern bool g_suspend_state;
 
 enum dz60rgb_layers {
 	_QWERTY,
@@ -26,7 +25,6 @@ enum dz60rgb_keycodes {
 #define _V_V_V_ KC_TRNS
 #define LT_CAPS LT(_NAV, KC_CAPS)
 #define LT_DEL  LT(_RGB, KC_DEL)
-extern rgb_config_t rgb_matrix_config;
 extern bool autoshift_enabled;
 #define MT_SLSH RSFT_T(KC_SLSH)
 #define MT_APP  RALT_T(KC_APP)

keyboards/dztech/dz60rgb/keymaps/mekanist/keymap.c

@@ -1,5 +1,4 @@
 #include QMK_KEYBOARD_H
-extern bool g_suspend_state;
 #define _LAYER0 0
 #define _LAYER1 1
 #define _LAYER2 2
@@ -50,8 +49,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
 
 
 
-extern led_config_t g_led_config;
-void rgb_matrix_layer_helper (uint8_t red, uint8_t green, uint8_t blue, bool default_layer) {
+void rgb_matrix_layer_helper (uint8_t red, uint8_t green, uint8_t blue) {
   for (int i = 0; i < DRIVER_LED_TOTAL; i++) {
     if (HAS_FLAGS(g_led_config.flags[i], LED_FLAG_MODIFIER)) {
         rgb_matrix_set_color( i, red, green, blue );

keyboards/dztech/dz60rgb/mcuconf.h

@@ -1,257 +0,0 @@
-/*
-    ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio
-
-    Licensed under the Apache License, Version 2.0 (the "License");
-    you may not use this file except in compliance with the License.
-    You may obtain a copy of the License at
-
-        http://www.apache.org/licenses/LICENSE-2.0
-
-    Unless required by applicable law or agreed to in writing, software
-    distributed under the License is distributed on an "AS IS" BASIS,
-    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-    See the License for the specific language governing permissions and
-    limitations under the License.
-*/
-
-#ifndef MCUCONF_H
-#define MCUCONF_H
-
-/*
- * STM32F3xx drivers configuration.
- * The following settings override the default settings present in
- * the various device driver implementation headers.
- * Note that the settings for each driver only have effect if the whole
- * driver is enabled in halconf.h.
- *
- * IRQ priorities:
- * 15...0       Lowest...Highest.
- *
- * DMA priorities:
- * 0...3        Lowest...Highest.
- */
-
-#define STM32F3xx_MCUCONF
-
-/*
- * HAL driver system settings.
- */
-#define STM32_NO_INIT                       FALSE
-#define STM32_PVD_ENABLE                    FALSE
-#define STM32_PLS                           STM32_PLS_LEV0
-#define STM32_HSI_ENABLED                   TRUE
-#define STM32_LSI_ENABLED                   TRUE
-#define STM32_HSE_ENABLED                   TRUE
-#define STM32_LSE_ENABLED                   FALSE
-#define STM32_SW                            STM32_SW_PLL
-#define STM32_PLLSRC                        STM32_PLLSRC_HSE
-#define STM32_PREDIV_VALUE                  1
-#define STM32_PLLMUL_VALUE                  9
-#define STM32_HPRE                          STM32_HPRE_DIV1
-#define STM32_PPRE1                         STM32_PPRE1_DIV2
-#define STM32_PPRE2                         STM32_PPRE2_DIV2
-#define STM32_MCOSEL                        STM32_MCOSEL_NOCLOCK
-#define STM32_ADC12PRES                     STM32_ADC12PRES_DIV1
-#define STM32_ADC34PRES                     STM32_ADC34PRES_DIV1
-#define STM32_USART1SW                      STM32_USART1SW_PCLK
-#define STM32_USART2SW                      STM32_USART2SW_PCLK
-#define STM32_USART3SW                      STM32_USART3SW_PCLK
-#define STM32_UART4SW                       STM32_UART4SW_PCLK
-#define STM32_UART5SW                       STM32_UART5SW_PCLK
-#define STM32_I2C1SW                        STM32_I2C1SW_SYSCLK
-#define STM32_I2C2SW                        STM32_I2C2SW_SYSCLK
-#define STM32_TIM1SW                        STM32_TIM1SW_PCLK2
-#define STM32_TIM8SW                        STM32_TIM8SW_PCLK2
-#define STM32_RTCSEL                        STM32_RTCSEL_LSI
-#define STM32_USB_CLOCK_REQUIRED            TRUE
-#define STM32_USBPRE                        STM32_USBPRE_DIV1P5
-
-#undef STM32_HSE_BYPASS
-// #error "oh no"
-// #endif
-
-/*
- * ADC driver system settings.
- */
-#define STM32_ADC_DUAL_MODE                 FALSE
-#define STM32_ADC_COMPACT_SAMPLES           FALSE
-#define STM32_ADC_USE_ADC1                  FALSE
-#define STM32_ADC_USE_ADC2                  FALSE
-#define STM32_ADC_USE_ADC3                  FALSE
-#define STM32_ADC_USE_ADC4                  FALSE
-#define STM32_ADC_ADC1_DMA_STREAM           STM32_DMA_STREAM_ID(1, 1)
-#define STM32_ADC_ADC2_DMA_STREAM           STM32_DMA_STREAM_ID(2, 1)
-#define STM32_ADC_ADC3_DMA_STREAM           STM32_DMA_STREAM_ID(2, 5)
-#define STM32_ADC_ADC4_DMA_STREAM           STM32_DMA_STREAM_ID(2, 2)
-#define STM32_ADC_ADC1_DMA_PRIORITY         2
-#define STM32_ADC_ADC2_DMA_PRIORITY         2
-#define STM32_ADC_ADC3_DMA_PRIORITY         2
-#define STM32_ADC_ADC4_DMA_PRIORITY         2
-#define STM32_ADC_ADC12_IRQ_PRIORITY        5
-#define STM32_ADC_ADC3_IRQ_PRIORITY         5
-#define STM32_ADC_ADC4_IRQ_PRIORITY         5
-#define STM32_ADC_ADC1_DMA_IRQ_PRIORITY     5
-#define STM32_ADC_ADC2_DMA_IRQ_PRIORITY     5
-#define STM32_ADC_ADC3_DMA_IRQ_PRIORITY     5
-#define STM32_ADC_ADC4_DMA_IRQ_PRIORITY     5
-#define STM32_ADC_ADC12_CLOCK_MODE          ADC_CCR_CKMODE_AHB_DIV1
-#define STM32_ADC_ADC34_CLOCK_MODE          ADC_CCR_CKMODE_AHB_DIV1
-
-/*
- * CAN driver system settings.
- */
-#define STM32_CAN_USE_CAN1                  FALSE
-#define STM32_CAN_CAN1_IRQ_PRIORITY         11
-
-/*
- * DAC driver system settings.
- */
-#define STM32_DAC_DUAL_MODE                 FALSE
-#define STM32_DAC_USE_DAC1_CH1              TRUE
-#define STM32_DAC_USE_DAC1_CH2              TRUE
-#define STM32_DAC_DAC1_CH1_IRQ_PRIORITY     10
-#define STM32_DAC_DAC1_CH2_IRQ_PRIORITY     10
-#define STM32_DAC_DAC1_CH1_DMA_PRIORITY     2
-#define STM32_DAC_DAC1_CH2_DMA_PRIORITY     2
-
-/*
- * EXT driver system settings.
- */
-#define STM32_EXT_EXTI0_IRQ_PRIORITY        6
-#define STM32_EXT_EXTI1_IRQ_PRIORITY        6
-#define STM32_EXT_EXTI2_IRQ_PRIORITY        6
-#define STM32_EXT_EXTI3_IRQ_PRIORITY        6
-#define STM32_EXT_EXTI4_IRQ_PRIORITY        6
-#define STM32_EXT_EXTI5_9_IRQ_PRIORITY      6
-#define STM32_EXT_EXTI10_15_IRQ_PRIORITY    6
-#define STM32_EXT_EXTI16_IRQ_PRIORITY       6
-#define STM32_EXT_EXTI17_IRQ_PRIORITY       6
-#define STM32_EXT_EXTI18_IRQ_PRIORITY       6
-#define STM32_EXT_EXTI19_IRQ_PRIORITY       6
-#define STM32_EXT_EXTI20_IRQ_PRIORITY       6
-#define STM32_EXT_EXTI21_22_29_IRQ_PRIORITY 6
-#define STM32_EXT_EXTI30_32_IRQ_PRIORITY    6
-#define STM32_EXT_EXTI33_IRQ_PRIORITY       6
-
-/*
- * GPT driver system settings.
- */
-#define STM32_GPT_USE_TIM1                  FALSE
-#define STM32_GPT_USE_TIM2                  FALSE
-#define STM32_GPT_USE_TIM3                  FALSE
-#define STM32_GPT_USE_TIM4                  FALSE
-#define STM32_GPT_USE_TIM6                  TRUE
-#define STM32_GPT_USE_TIM7                  TRUE
-#define STM32_GPT_USE_TIM8                  TRUE
-#define STM32_GPT_TIM1_IRQ_PRIORITY         7
-#define STM32_GPT_TIM2_IRQ_PRIORITY         7
-#define STM32_GPT_TIM3_IRQ_PRIORITY         7
-#define STM32_GPT_TIM4_IRQ_PRIORITY         7
-#define STM32_GPT_TIM6_IRQ_PRIORITY         7
-#define STM32_GPT_TIM7_IRQ_PRIORITY         7
-#define STM32_GPT_TIM8_IRQ_PRIORITY         7
-
-/*
- * I2C driver system settings.
- */
-#define STM32_I2C_USE_I2C1                  TRUE
-#define STM32_I2C_USE_I2C2                  FALSE
-#define STM32_I2C_BUSY_TIMEOUT              50
-#define STM32_I2C_I2C1_IRQ_PRIORITY         10
-#define STM32_I2C_I2C2_IRQ_PRIORITY         10
-#define STM32_I2C_USE_DMA                   TRUE
-#define STM32_I2C_I2C1_DMA_PRIORITY         1
-#define STM32_I2C_I2C2_DMA_PRIORITY         1
-#define STM32_I2C_DMA_ERROR_HOOK(i2cp)      osalSysHalt("DMA failure")
-
-/*
- * ICU driver system settings.
- */
-#define STM32_ICU_USE_TIM1                  FALSE
-#define STM32_ICU_USE_TIM2                  FALSE
-#define STM32_ICU_USE_TIM3                  FALSE
-#define STM32_ICU_USE_TIM4                  FALSE
-#define STM32_ICU_USE_TIM8                  FALSE
-#define STM32_ICU_TIM1_IRQ_PRIORITY         7
-#define STM32_ICU_TIM2_IRQ_PRIORITY         7
-#define STM32_ICU_TIM3_IRQ_PRIORITY         7
-#define STM32_ICU_TIM4_IRQ_PRIORITY         7
-#define STM32_ICU_TIM8_IRQ_PRIORITY         7
-
-/*
- * PWM driver system settings.
- */
-#define STM32_PWM_USE_ADVANCED              FALSE
-#define STM32_PWM_USE_TIM1                  FALSE
-#define STM32_PWM_USE_TIM2                  FALSE
-#define STM32_PWM_USE_TIM3                  FALSE
-#define STM32_PWM_USE_TIM4                  FALSE
-#define STM32_PWM_USE_TIM8                  FALSE
-#define STM32_PWM_TIM1_IRQ_PRIORITY         7
-#define STM32_PWM_TIM2_IRQ_PRIORITY         7
-#define STM32_PWM_TIM3_IRQ_PRIORITY         7
-#define STM32_PWM_TIM4_IRQ_PRIORITY         7
-#define STM32_PWM_TIM8_IRQ_PRIORITY         7
-
-/*
- * SERIAL driver system settings.
- */
-#define STM32_SERIAL_USE_USART1             FALSE
-#define STM32_SERIAL_USE_USART2             FALSE
-#define STM32_SERIAL_USE_USART3             FALSE
-#define STM32_SERIAL_USE_UART4              FALSE
-#define STM32_SERIAL_USE_UART5              FALSE
-#define STM32_SERIAL_USART1_PRIORITY        12
-#define STM32_SERIAL_USART2_PRIORITY        12
-#define STM32_SERIAL_USART3_PRIORITY        12
-#define STM32_SERIAL_UART4_PRIORITY         12
-#define STM32_SERIAL_UART5_PRIORITY         12
-
-/*
- * SPI driver system settings.
- */
-#define STM32_SPI_USE_SPI1                  FALSE
-#define STM32_SPI_USE_SPI2                  FALSE
-#define STM32_SPI_USE_SPI3                  FALSE
-#define STM32_SPI_SPI1_DMA_PRIORITY         1
-#define STM32_SPI_SPI2_DMA_PRIORITY         1
-#define STM32_SPI_SPI3_DMA_PRIORITY         1
-#define STM32_SPI_SPI1_IRQ_PRIORITY         10
-#define STM32_SPI_SPI2_IRQ_PRIORITY         10
-#define STM32_SPI_SPI3_IRQ_PRIORITY         10
-#define STM32_SPI_DMA_ERROR_HOOK(spip)      osalSysHalt("DMA failure")
-
-/*
- * ST driver system settings.
- */
-#define STM32_ST_IRQ_PRIORITY               8
-#define STM32_ST_USE_TIMER                  2
-
-/*
- * UART driver system settings.
- */
-#define STM32_UART_USE_USART1               FALSE
-#define STM32_UART_USE_USART2               FALSE
-#define STM32_UART_USE_USART3               FALSE
-#define STM32_UART_USART1_IRQ_PRIORITY      12
-#define STM32_UART_USART2_IRQ_PRIORITY      12
-#define STM32_UART_USART3_IRQ_PRIORITY      12
-#define STM32_UART_USART1_DMA_PRIORITY      0
-#define STM32_UART_USART2_DMA_PRIORITY      0
-#define STM32_UART_USART3_DMA_PRIORITY      0
-#define STM32_UART_DMA_ERROR_HOOK(uartp)    osalSysHalt("DMA failure")
-
-/*
- * USB driver system settings.
- */
-#define STM32_USB_USE_USB1                  TRUE
-#define STM32_USB_LOW_POWER_ON_SUSPEND      FALSE
-#define STM32_USB_USB1_HP_IRQ_PRIORITY      13
-#define STM32_USB_USB1_LP_IRQ_PRIORITY      14
-
-/*
- * WDG driver system settings.
- */
-#define STM32_WDG_USE_IWDG                  FALSE
-
-#endif /* MCUCONF_H */

keyboards/dztech/dz60rgb/rules.mk

@@ -1,43 +1,6 @@
-# project specific files
-
-## chip/board settings
-#   the next two should match the directories in
-#   <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
-MCU_FAMILY = STM32
-MCU_SERIES = STM32F3xx
-
-# Linker script to use
-#   it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
-#   or <this_dir>/ld/
-MCU_LDSCRIPT = STM32F303xC
-
-# Startup code to use
-#  - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/
-MCU_STARTUP = stm32f3xx
-
-# Board: it should exist either in <chibios>/os/hal/boards/
-#  or <this_dir>/boards
-BOARD = GENERIC_STM32_F303XC
-
-# Cortex version
-MCU  = cortex-m4
-
-# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
-ARMV = 7
-
-USE_FPU = yes
-
-# Vector table for application
-# 0x00000000-0x00001000 area is occupied by bootlaoder.*/
-# The CORTEX_VTOR... is needed only for MCHCK/Infinity KB
-# OPT_DEFS = -DCORTEX_VTOR_INIT=0x08005000
-OPT_DEFS =
-
-# Options to pass to dfu-util when flashing
+MCU  = STM32F303
 DFU_ARGS = -d 0483:df11 -a 0 -s 0x08000000:leave
 DFU_SUFFIX_ARGS = -p DF11 -v 0483
-
-
 BACKLIGHT_ENABLE = no
 BOOTMAGIC_ENABLE = lite           # Virtual DIP switch configuration
 MOUSEKEY_ENABLE = yes              # Mouse keys

keyboards/dztech/dz65rgb/config.h

@@ -26,4 +26,4 @@
 #define DRIVER_COUNT 2
 #define DRIVER_1_LED_TOTAL 35
 #define DRIVER_2_LED_TOTAL 33
-#define DRIVER_LED_TOTAL DRIVER_1_LED_TOTAL + DRIVER_2_LED_TOTAL
+#define DRIVER_LED_TOTAL (DRIVER_1_LED_TOTAL + DRIVER_2_LED_TOTAL)

keyboards/dztech/dz65rgb/dz65rgb.c

@@ -94,11 +94,21 @@ led_config_t g_led_config = { {
     4, 4, 4, 4, 1, 1, 1, 1
 } };
 
+void matrix_init_kb(void) {
+    matrix_init_user();
+}
+void matrix_scan_kb(void) {
+    matrix_scan_user();
+}
+bool process_record_kb(uint16_t keycode, keyrecord_t *record) {
+    return process_record_user(keycode, record);
+}
 void suspend_power_down_kb(void)
 {
     rgb_matrix_set_suspend_state(true);
     suspend_power_down_user();
 }
+
 void suspend_wakeup_init_kb(void)
 {
     rgb_matrix_set_suspend_state(false);

keyboards/dztech/dz65rgb/keymaps/default/keymap.c

@@ -1,5 +1,4 @@
 #include QMK_KEYBOARD_H
-extern bool g_suspend_state;
 #define _LAYER0 0
 #define _LAYER1 1
 const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {

keyboards/dztech/dz65rgb/rules.mk

@@ -1,4 +1,6 @@
 MCU  = STM32F303
+DFU_ARGS = -d 0483:df11 -a 0 -s 0x08000000:leave
+DFU_SUFFIX_ARGS = -p DF11 -v 0483
 BACKLIGHT_ENABLE = no
 BOOTMAGIC_ENABLE = lite           # Virtual DIP switch configuration
 MOUSEKEY_ENABLE = yes              # Mouse keys

keyboards/ergodox_ez/config.h

@@ -107,7 +107,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 #define DRIVER_COUNT 2
 #define DRIVER_1_LED_TOTAL 24
 #define DRIVER_2_LED_TOTAL 24
-#define DRIVER_LED_TOTAL DRIVER_1_LED_TOTAL + DRIVER_2_LED_TOTAL
+#define DRIVER_LED_TOTAL (DRIVER_1_LED_TOTAL + DRIVER_2_LED_TOTAL)
 
 // #define RGBLIGHT_COLOR_LAYER_0 0x00, 0x00, 0xFF
 /* #define RGBLIGHT_COLOR_LAYER_1 0x00, 0x00, 0xFF */

keyboards/hs60/v1/config.h

@@ -134,4 +134,4 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 #define DRIVER_2_LED_TOTAL 32
 #endif
 
-#define DRIVER_LED_TOTAL DRIVER_1_LED_TOTAL + DRIVER_2_LED_TOTAL
+#define DRIVER_LED_TOTAL (DRIVER_1_LED_TOTAL + DRIVER_2_LED_TOTAL)

keyboards/hs60/v2/keymaps/stanrc85/keymap.c

@@ -17,33 +17,33 @@
 #include "stanrc85.h"
 
 const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
-	[0] = LAYOUT_60_ansi(
-		TD_TESC, KC_1,    KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8,    KC_9,    KC_0,    KC_MINS, KC_EQL,  KC_BSPC,
-		KC_TAB,  KC_Q,    KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I,    KC_O,    KC_P,    KC_LBRC, KC_RBRC, KC_BSLS,
-		KC_CTLE, KC_A,    KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K,    KC_L,    KC_SCLN, KC_QUOT, KC_ENT,
-		KC_LSFT, KC_Z,    KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT,  KC_SLSH, KC_RSFT,
-		KC_LCTL, KC_LGUI, KC_LALT,          LT_SPCF,          KC_RALT, TD_TWIN, MO(3),   TD_TCTL),
+  [0] = LAYOUT_60_ansi(
+	TD_TESC, KC_1,    KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8,    KC_9,    KC_0,    KC_MINS, KC_EQL,  KC_BSPC,
+	KC_TAB,  KC_Q,    KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I,    KC_O,    KC_P,    KC_LBRC, KC_RBRC, KC_BSLS,
+	KC_CTLE, KC_A,    KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K,    KC_L,    KC_SCLN, KC_QUOT, KC_ENT,
+	KC_LSFT, KC_Z,    KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT,  KC_SLSH, KC_RSFT,
+	KC_LCTL, KC_LGUI, KC_LALT,          LT_SPCF,          KC_RALT, TD_TWIN, MO(3),   TD_TCTL),
 
-	[1] = LAYOUT_60_ansi(
-		KC_GESC, KC_1,    KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8,    KC_9,   KC_0,    KC_MINS, KC_EQL,  KC_BSPC,
-		KC_TAB,  KC_Q,    KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I,    KC_O,   KC_P,    KC_LBRC, KC_RBRC, KC_BSLS,
-		KC_CAPS, KC_A,    KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K,    KC_L,   KC_SCLN, KC_QUOT, KC_ENT,
-		KC_LSFT, KC_Z,    KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT,
-		KC_LCTL, KC_LGUI, KC_LALT,          KC_SPC ,          KC_RALT, MO(2),  MO(3),   KC_RCTL),
+  [1] = LAYOUT_60_ansi(
+	KC_GESC, KC_1,    KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8,    KC_9,   KC_0,    KC_MINS, KC_EQL,  KC_BSPC,
+	KC_TAB,  KC_Q,    KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I,    KC_O,   KC_P,    KC_LBRC, KC_RBRC, KC_BSLS,
+	KC_CAPS, KC_A,    KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K,    KC_L,   KC_SCLN, KC_QUOT, KC_ENT,
+	KC_LSFT, KC_Z,    KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT,
+	KC_LCTL, KC_LGUI, KC_LALT,          KC_SPC ,          KC_RALT, MO(2),  MO(3),   KC_RCTL),
 
-	[2] = LAYOUT_60_ansi(
-		KC_TILD, KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,  KC_DEL,
-		_______, _______, CA_QUOT, KC_VOLU, CA_SCLN, _______, _______, KC_HOME, KC_UP,   KC_END,  _______, _______, _______, KC_INS,
-		KC_CAPS, _______, KC_MUTE, KC_VOLD, KC_MPLY, _______, _______, KC_LEFT, KC_DOWN, KC_RGHT, _______, _______, _______,
-		_______, KC_RDP,  _______, _______, _______, _______, _______, _______, KC_WBAK, KC_WFWD, _______, _______,
-		_______, _______, _______,                   _______,                   _______, _______, _______, _______),
+  [2] = LAYOUT_60_ansi(
+	KC_TILD, KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,  KC_DEL,
+	_______, _______, CA_QUOT, KC_VOLU, CA_SCLN, _______, _______, KC_HOME, KC_UP,   KC_END,  KC_PSCR, _______, _______, KC_INS,
+	KC_CAPS, _______, KC_MUTE, KC_VOLD, KC_MPLY, _______, _______, KC_LEFT, KC_DOWN, KC_RGHT, _______, _______, _______,
+	_______, KC_RDP,  _______, _______, _______, _______, _______, _______, KC_WBAK, KC_WFWD, _______, _______,
+	_______, _______, _______,                   _______,                   _______, _______, _______, _______),
 
-	[3] = LAYOUT_60_ansi(
-		_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, EEP_RST,
-		_______, EF_INC,  ES_INC,  S1_INC,  H1_INC,  S2_INC,  H2_INC,  BR_INC,  _______, _______, _______, _______, _______, RESET,
-		TG(1),   EF_DEC,  ES_DEC,  S1_DEC,  H1_DEC,  S2_DEC,  H2_DEC,  BR_DEC,  _______, _______, _______, _______, KC_MAKE,
-		_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,
-		_______, _______, _______,                   _______,                   _______, _______, _______, _______)
+  [3] = LAYOUT_60_ansi(
+	_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, EEP_RST,
+	_______, EF_INC,  ES_INC,  S1_INC,  H1_INC,  S2_INC,  H2_INC,  BR_INC,  _______, _______, _______, _______, _______, RESET,
+	_______, EF_DEC,  ES_DEC,  S1_DEC,  H1_DEC,  S2_DEC,  H2_DEC,  BR_DEC,  _______, _______, _______, _______, KC_MAKE,
+	_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,
+	_______, _______, _______,                   _______,                   _______, _______, _______, TG(1))
 };
 
 // Backlight specific keys:

keyboards/hs60/v2/keymaps/stanrc85/rules.mk

@@ -1,9 +1,9 @@
 # project specific files
 SRC =	keyboards/zeal60/zeal60.c \
-    keyboards/zeal60/rgb_backlight.c \
-		drivers/issi/is31fl3733.c \
-		quantum/color.c \
-		drivers/arm/i2c_master.c
+        keyboards/zeal60/rgb_backlight.c \
+	    drivers/issi/is31fl3733.c \
+	    quantum/color.c \
+	    drivers/arm/i2c_master.c
 
 ## chip/board settings
 #   the next two should match the directories in

keyboards/kbdfans/kbd67/rev2/config.h

@@ -0,0 +1,64 @@
+/*
+Copyright 2019 Vorror
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0xFEED
+#define PRODUCT_ID      0x6060
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    KBDFans
+#define PRODUCT         KBD67v2
+#define DESCRIPTION     65% Keyboard
+
+/* key matrix size */
+#define MATRIX_ROWS 5
+#define MATRIX_COLS 16
+
+#define MATRIX_ROW_PINS { B7, D0, F0, F1, F4 }
+#define MATRIX_COL_PINS { B0, B1, B2, B3, D1, D2, D3, D6, D7, B4, B6, C6, C7, F7, F6, F5 }
+#define UNUSED_PINS
+
+/* COL2ROW or ROW2COL */
+#define DIODE_DIRECTION COL2ROW
+
+/* number of backlight levels */
+#define BACKLIGHT_PIN B5
+#ifdef BACKLIGHT_PIN
+#define BACKLIGHT_LEVELS 3
+#endif
+
+/* Set 0 if debouncing isn't needed */
+#define DEBOUNCING_DELAY 5
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+#define RGB_DI_PIN E2
+#ifdef RGB_DI_PIN
+#define RGBLIGHT_ANIMATIONS
+#define RGBLED_NUM 18
+#define RGBLIGHT_HUE_STEP 8
+#define RGBLIGHT_SAT_STEP 8
+#define RGBLIGHT_VAL_STEP 8
+#define RGBLIGHT_LIMIT_VAL 240
+#endif

keyboards/kbdfans/kbd67/rev2/info.json

@@ -0,0 +1,16 @@
+{
+  "keyboard_name": "kbd67v2",
+  "url": "",
+  "maintainer": "qmk",
+  "width": 16,
+  "height": 5,
+  "layouts": {
+      "LAYOUT_all": {
+          "layout": [{"x":0, "y":0}, {"x":1, "y":0}, {"x":2, "y":0}, {"x":3, "y":0}, {"x":4, "y":0}, {"x":5, "y":0}, {"x":6, "y":0}, {"x":7, "y":0}, {"x":8, "y":0}, {"x":9, "y":0}, {"x":10, "y":0}, {"x":11, "y":0}, {"x":12, "y":0}, {"x":13, "y":0}, {"x":14, "y":0}, {"x":15, "y":0}, {"x":0, "y":1, "w":1.5}, {"x":1.5, "y":1}, {"x":2.5, "y":1}, {"x":3.5, "y":1}, {"x":4.5, "y":1}, {"x":5.5, "y":1}, {"x":6.5, "y":1}, {"x":7.5, "y":1}, {"x":8.5, "y":1}, {"x":9.5, "y":1}, {"x":10.5, "y":1}, {"x":11.5, "y":1}, {"x":12.5, "y":1}, {"x":13.5, "y":1, "w":1.5}, {"x":15, "y":1}, {"x":0, "y":2, "w":1.75}, {"x":1.75, "y":2}, {"x":2.75, "y":2}, {"x":3.75, "y":2}, {"x":4.75, "y":2}, {"x":5.75, "y":2}, {"x":6.75, "y":2}, {"x":7.75, "y":2}, {"x":8.75, "y":2}, {"x":9.75, "y":2}, {"x":10.75, "y":2}, {"x":11.75, "y":2}, {"x":12.75, "y":2, "w":2.25}, {"x":15, "y":2}, {"x":0, "y":3, "w":1.25}, {"x":1.25, "y":3}, {"x":2.25, "y":3}, {"x":3.25, "y":3}, {"x":4.25, "y":3}, {"x":5.25, "y":3}, {"x":6.25, "y":3}, {"x":7.25, "y":3}, {"x":8.25, "y":3}, {"x":9.25, "y":3}, {"x":10.25, "y":3}, {"x":11.25, "y":3}, {"x":12.25, "y":3, "w":1.75}, {"x":14, "y":3}, {"x":15, "y":3}, {"x":0, "y":4, "w":1.25}, {"x":1.25, "y":4, "w":1.25}, {"x":2.5, "y":4, "w":1.25}, {"x":3.75, "y":4, "w":2.75}, {"x":6.5, "y":4, "w":1.25}, {"x":7.75, "y":4, "w":2.25}, {"x":10, "y":4}, {"x":11, "y":4}, {"x":12, "y":4}, {"x":13, "y":4}, {"x":14, "y":4}, {"x":15, "y":4}]
+      },
+
+      "LAYOUT_65_ansi": {
+          "layout": [{"x":0, "y":0}, {"x":1, "y":0}, {"x":2, "y":0}, {"x":3, "y":0}, {"x":4, "y":0}, {"x":5, "y":0}, {"x":6, "y":0}, {"x":7, "y":0}, {"x":8, "y":0}, {"x":9, "y":0}, {"x":10, "y":0}, {"x":11, "y":0}, {"x":12, "y":0}, {"x":13, "y":0, "w":2}, {"x":15, "y":0}, {"x":0, "y":1, "w":1.5}, {"x":1.5, "y":1}, {"x":2.5, "y":1}, {"x":3.5, "y":1}, {"x":4.5, "y":1}, {"x":5.5, "y":1}, {"x":6.5, "y":1}, {"x":7.5, "y":1}, {"x":8.5, "y":1}, {"x":9.5, "y":1}, {"x":10.5, "y":1}, {"x":11.5, "y":1}, {"x":12.5, "y":1}, {"x":13.5, "y":1, "w":1.5}, {"x":15, "y":1}, {"x":0, "y":2, "w":1.75}, {"x":1.75, "y":2}, {"x":2.75, "y":2}, {"x":3.75, "y":2}, {"x":4.75, "y":2}, {"x":5.75, "y":2}, {"x":6.75, "y":2}, {"x":7.75, "y":2}, {"x":8.75, "y":2}, {"x":9.75, "y":2}, {"x":10.75, "y":2}, {"x":11.75, "y":2}, {"x":12.75, "y":2, "w":2.25}, {"x":15, "y":2}, {"x":0, "y":3, "w":2.25}, {"x":2.25, "y":3}, {"x":3.25, "y":3}, {"x":4.25, "y":3}, {"x":5.25, "y":3}, {"x":6.25, "y":3}, {"x":7.25, "y":3}, {"x":8.25, "y":3}, {"x":9.25, "y":3}, {"x":10.25, "y":3}, {"x":11.25, "y":3}, {"x":12.25, "y":3, "w":1.75}, {"x":14, "y":3}, {"x":15, "y":3}, {"x":0, "y":4, "w":1.25}, {"x":1.25, "y":4, "w":1.25}, {"x":2.5, "y":4, "w":1.25}, {"x":3.75, "y":4, "w":6.25}, {"x":10, "y":4}, {"x":11, "y":4}, {"x":12, "y":4}, {"x":13, "y":4}, {"x":14, "y":4}, {"x":15, "y":4}]
+      }
+  }
+}

keyboards/kbdfans/kbd67/rev2/keymaps/default/config.h

@@ -0,0 +1,19 @@
+/* Copyright 2018 MechMerlin
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+
+// place overrides here

keyboards/kbdfans/kbd67/rev2/keymaps/default/keymap.c

@@ -0,0 +1,99 @@
+/* Copyright 2018 'mechmerlin'
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include QMK_KEYBOARD_H
+
+// Defines the keycodes used by our macros in process_record_user
+enum custom_keycodes {
+  QMKBEST = SAFE_RANGE,
+  QMKURL
+};
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+/* Keymap (Base Layer) Default Layer
+   * ,----------------------------------------------------------------.
+   * |Esc|  1|  2|  3|  4|  5|  6|  7|  8|  9|  0|  -|  =|Backsp |Home|
+   * |----------------------------------------------------------------|
+   * |Tab  |  Q|  W|  E|  R|  T|  Y|  U|  I|  O|  P|  [|  ]|  \  |PgUp|
+   * |----------------------------------------------------------------|
+   * |Ctrl   |  A|  S|  D|  F|  G|  H|  J|  K|  L|  ;|  '|Return |PgDn|
+   * |----------------------------------------------------------------|
+   * |Shift   |  Z|  X|  C|  V|  B|  N|  M|  ,|  .|  /|Shift | Up|End |
+   * |----------------------------------------------------------------|
+   * |Ctrl|Win |Alt |        Space          |Alt| FN|Ctrl|Lef|Dow|Rig |
+   * `----------------------------------------------------------------'
+   */
+[0] = LAYOUT_65_ansi(
+  KC_ESC,  KC_1,    KC_2,   KC_3,   KC_4,   KC_5,   KC_6,   KC_7,   KC_8,    KC_9,    KC_0,    KC_MINS, KC_EQL,  KC_BSPC, KC_HOME, \
+  KC_TAB,  KC_Q,    KC_W,   KC_E,   KC_R,   KC_T,   KC_Y,   KC_U,   KC_I,    KC_O,    KC_P,    KC_LBRC, KC_RBRC, KC_BSLS, KC_PGUP, \
+  KC_LCTL, KC_A,    KC_S,   KC_D,   KC_F,   KC_G,   KC_H,   KC_J,   KC_K,    KC_L,    KC_SCLN, KC_QUOT,          KC_ENT, KC_PGDN,  \
+  KC_LSFT, KC_Z,    KC_X,   KC_C,   KC_V,   KC_B,   KC_N,   KC_M,   KC_COMM, KC_DOT,  KC_SLSH, KC_RSFT, KC_UP,   KC_END,           \
+  KC_LCTL, KC_LGUI, KC_LALT,                KC_SPC,                          KC_RALT, MO(1),   KC_RCTL, KC_LEFT, KC_DOWN, KC_RGHT),
+
+  /* Keymap Fn Layer
+   * ,----------------------------------------------------------------.
+   * |~ `|F1 |F2 |F3 |F4 |F5 |F6 |F7 |F8 |F9 |F10|F11|F12|Del    |Ins |
+   * |----------------------------------------------------------------|
+   * |Caps |   |Up |   |   |   |   |   |PSc|SLk|Pau|Up |   |     |    |
+   * |----------------------------------------------------------------|
+   * |      |Lef|Dow|Rig|   |   |   |   |Hom|PUp|Lef|Rig|        |    |
+   * |----------------------------------------------------------------|
+   * |        |   |   |   |   |   |   |   |End|PDn|Dow|      |PUp|    |
+   * |----------------------------------------------------------------|
+   * |    |    |    |                       |   |   |    |Hom|PDn|End |
+   * `----------------------------------------------------------------'
+   */
+[1] = LAYOUT_65_ansi(
+   KC_GRV,  KC_F1,  KC_F2,  KC_F3,  KC_F4,  KC_F5,  KC_F6,  KC_F7,  KC_F8,  KC_F9, KC_F10, KC_F11, KC_F12,          KC_DEL,KC_INS, \
+   KC_CAPS,_______,  KC_UP,_______,_______,_______,_______,_______,KC_PSCR,KC_SLCK,KC_PAUS,  KC_UP,_______,     _______,_______,   \
+      _______,KC_LEFT,KC_DOWN,KC_RGHT,_______,_______,_______,_______,KC_HOME,KC_PGUP,KC_LEFT,KC_RGHT,            _______,_______, \
+           _______,_______,_______,_______,_______,_______,_______,_______, KC_END,KC_PGDN,KC_DOWN,       _______,KC_PGUP,_______, \
+    _______,  _______,  _______,                     _______,                     _______,_______,_______,KC_HOME,KC_PGDN, KC_END),
+
+};
+
+bool process_record_user(uint16_t keycode, keyrecord_t *record) {
+  switch (keycode) {
+    case QMKBEST:
+      if (record->event.pressed) {
+        // when keycode QMKBEST is pressed
+        SEND_STRING("QMK is the best thing ever!");
+      } else {
+        // when keycode QMKBEST is released
+      }
+      break;
+    case QMKURL:
+      if (record->event.pressed) {
+        // when keycode QMKURL is pressed
+        SEND_STRING("https://qmk.fm/" SS_TAP(X_ENTER));
+      } else {
+        // when keycode QMKURL is released
+      }
+      break;
+  }
+  return true;
+}
+
+void matrix_init_user(void) {
+
+}
+
+void matrix_scan_user(void) {
+
+}
+
+void led_set_user(uint8_t usb_led) {
+
+}

keyboards/kbdfans/kbd67/rev2/keymaps/default/readme.md

@@ -0,0 +1 @@
+# The default keymap for kbd67

keyboards/kbdfans/kbd67/rev2/keymaps/koba/config.h

@@ -0,0 +1,17 @@
+/* Copyright 2019 Daisuke Kobayashi
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once

keyboards/kbdfans/kbd67/rev2/keymaps/koba/keymap.c

@@ -0,0 +1,61 @@
+/* Copyright 2019 Daisuke Kobayashi
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include QMK_KEYBOARD_H
+#include "keymap_jp.h"
+
+#define RGB_RMO RGB_RMOD
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+/* Keymap (Base Layer) Default Layer
+   * ,----------------------------------------------------------------.
+   * |Esc|  1|  2|  3|  4|  5|  6|  7|  8|  9|  0|  -|  ^|  \|BS |Del |
+   * |----------------------------------------------------------------|
+   * |Tab  |  Q|  W|  E|  R|  T|  Y|  U|  I|  O|  P|  @|  [| Ent |PgUp|
+   * |------------------------------------------------------.    |----|
+   * |H/Z   |  A|  S|  D|  F|  G|  H|  J|  K|  L|  ;|  :|  ]|    |PgDn|
+   * |----------------------------------------------------------------|
+   * |Shift   |  Z|  X|  C|  V|  B|  N|  M|  ,|  .|  /|Shift |Up |PScr|
+   * |----------------------------------------------------------------|
+   * |Ctrl|Win |Alt | Space    |Fn | Space  |Alt |Ctrl|  |Lef|Dow|Rig |
+   * `------------------------------------------------'  `------------'
+   */
+[0] = LAYOUT_all(
+  KC_ESC,  KC_1,   KC_2,   KC_3,   KC_4,   KC_5,   KC_6,   KC_7,   KC_8,    KC_9,    KC_0,    KC_MINS, JP_CIRC, KC_JYEN, KC_BSPC, KC_DELT, \
+  KC_TAB,     KC_Q,   KC_W,   KC_E,   KC_R,   KC_T,   KC_Y,   KC_U,   KC_I,    KC_O,    KC_P,    JP_AT,   JP_LBRC, JP_RBRC,       KC_PGUP, \
+  KC_ZKHK,       KC_A,   KC_S,   KC_D,   KC_F,   KC_G,   KC_H,   KC_J,   KC_K,    KC_L,    KC_SCLN, JP_COLN,       KC_ENT,        KC_PGDN, \
+  KC_LSFT, XXXXXXX, KC_Z,   KC_X,   KC_C,   KC_V,   KC_B,   KC_N,   KC_M,   KC_COMM, KC_DOT,  KC_SLSH, KC_RSFT,          KC_UP,   KC_PSCR, \
+  KC_LCTL, KC_LGUI, KC_LALT,        KC_SPC,         MO(1),          KC_SPC,          KC_RALT, KC_RCTL, XXXXXXX, KC_LEFT, KC_DOWN, KC_RGHT),
+
+  /* Keymap Fn Layer
+   * ,----------------------------------------------------------------.
+   * |Rst| F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12|   |   |Ins |
+   * |----------------------------------------------------------------|
+   * |     |M- |M+ |RGB|H- |H+ |   |   |Prt|SLk|Pau|   |   |     |    |
+   * |------------------------------------------------------.    |----|
+   * |Caps  |Vo-|Vo+|Mut|S- |S+ |  *|  /|Hom|PUp|   |   |   |    |    |
+   * |----------------------------------------------------------------|
+   * |        |BL-|BL+|BL |V- |V+ |  +|  -|End|PDn|  _|      |PUp|    |
+   * |----------------------------------------------------------------|
+   * |    |    |    | Muhenkan |   | Henkan |Kana|Menu|  |Hom|PDn|End |
+   * `------------------------------------------------'  `------------'
+   */
+[1] = LAYOUT_all(
+   RESET,  KC_F1,  KC_F2,  KC_F3,  KC_F4,  KC_F5,  KC_F6,  KC_F7,  KC_F8,  KC_F9,  KC_F10, KC_F11, KC_F12, XXXXXXX,_______,KC_INS,  \
+   _______,   RGB_RMO,RGB_MOD,RGB_TOG,RGB_HUD,RGB_HUI,XXXXXXX,XXXXXXX,KC_PSCR,KC_SLCK,KC_PAUS,XXXXXXX,XXXXXXX,XXXXXXX,     _______, \
+   KC_CAPS,     KC_VOLD,KC_VOLU,KC_MUTE,RGB_SAD,RGB_SAI,KC_PAST,KC_PSLS,KC_HOME,KC_PGUP,XXXXXXX,XXXXXXX,      KC_PENT,     _______, \
+   _______,_______,BL_DEC, BL_INC, BL_TOGG,RGB_VAD,RGB_VAI,KC_PPLS,KC_PMNS,KC_END, KC_PGDN,JP_UNDS,_______,        KC_PGUP,_______, \
+   _______,_______,_______,        KC_MHEN,        _______,        KC_HENK,        KC_KANA,KC_APP, _______,KC_HOME,KC_PGDN,KC_END),
+};

keyboards/kbdfans/kbd67/rev2/keymaps/koba/readme.md

@@ -0,0 +1,7 @@
+# Koba's keymap for KBD67
+
+![keyboard-layout](https://user-images.githubusercontent.com/1042121/54736578-244ffe80-4bef-11e9-9882-37611b4efdf4.png)
+
+- JIS layout.
+- Fn layer is arranged like HHKB.
+- 3 splitted space bar. (Space-Fn-Space)

keyboards/kbdfans/kbd67/rev2/readme.md

@@ -0,0 +1,13 @@
+# KBD67 rev2
+
+65% pcb with blocker. Revision 2 (Manufactured after 05/01/19). 
+
+Keyboard Maintainer: [Vorror](https://github.com/vorror)  
+Hardware Supported: KBD67v2 PCB (Sometimes sold under the name "KBD65")  
+Hardware Availability: KBDFans [Keyboard Kit](https://kbdfans.cn/products/coming-soon-kbd67-mechanical-keyboard-diy-kit), [PCB](https://kbdfans.cn/collections/65/products/kbd65-65-custom-mechanical-keyboard-pcb)
+
+Make example for this keyboard (after setting up your build environment):
+
+    make kbdfans/kbd67/rev2:default
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/kbdfans/kbd67/rev2/rev2.c

@@ -0,0 +1,42 @@
+/* Copyright 2019 Vorror
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include "rev2.h"
+
+void matrix_init_kb(void) {
+	// put your keyboard start-up code here
+	// runs once when the firmware starts up
+
+	matrix_init_user();
+}
+
+void matrix_scan_kb(void) {
+	// put your looping keyboard code here
+	// runs every cycle (a lot)
+
+	matrix_scan_user();
+}
+
+bool process_record_kb(uint16_t keycode, keyrecord_t *record) {
+	// put your per-action keyboard code here
+	// runs for every action, just before processing by the firmware
+
+	return process_record_user(keycode, record);
+}
+
+void led_set_kb(uint8_t usb_led) {
+	// put your keyboard LED indicator (ex: Caps Lock LED) toggling code here
+	led_set_user(usb_led);
+}

keyboards/kbdfans/kbd67/rev2/rev2.h

@@ -0,0 +1,57 @@
+/* Copyright 2018 MechMerlin
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#pragma once
+
+#include "quantum.h"
+
+/* This a shortcut to help you visually see your layout.
+ *
+ * The first section contains all of the arguments representing the physical
+ * layout of the board and position of the keys.
+ *
+ * The second converts the arguments into a two-dimensional array which
+ * represents the switch matrix.
+ */
+#define LAYOUT_all( \
+    K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, K0E, K0F, \
+    K10,      K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, K1E, K1F, \
+    K20,      K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, K2C, K2D,      K2F, \
+    K30, K31, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B,      K3D, K3E, K3F, \
+    K40, K41,      K43, K44,      K46,      K48,      K4A, K4B, K4C, K4D, K4E, K4F  \
+) \
+{ \
+    { K00, K01,   K02,   K03, K04, K05,   K06, K07,   K08, K09,   K0A, K0B, K0C,   K0D, K0E,   K0F }, \
+    { K10, KC_NO, K12,   K13, K14, K15,   K16, K17,   K18, K19,   K1A, K1B, K1C,   K1D, K1E,   K1F }, \
+    { K20, KC_NO, K22,   K23, K24, K25,   K26, K27,   K28, K29,   K2A, K2B, K2C,   K2D, KC_NO, K2F }, \
+    { K30, K31,   K32,   K33, K34, K35,   K36, K37,   K38, K39,   K3A, K3B, KC_NO, K3D, K3E,   K3F }, \
+    { K40, K41,   KC_NO, K43, K44, KC_NO, K46, KC_NO, K48, KC_NO, K4A, K4B, K4C,   K4D, K4E,   K4F }, \
+}
+
+#define LAYOUT_65_ansi( \
+    K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C,      K0E, K0F, \
+    K10,      K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, K1E, K1F, \
+    K20,      K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, K2C, K2D,      K2F, \
+    K30,      K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B,      K3D, K3E, K3F, \
+    K40, K41,      K43,           K46,                K4A, K4B, K4C, K4D, K4E, K4F  \
+) \
+{ \
+    { K00, K01,   K02,   K03, K04,   K05,   K06, K07,   K08,   K09,   K0A, K0B, K0C,   KC_NO, K0E,   K0F }, \
+    { K10, KC_NO, K12,   K13, K14,   K15,   K16, K17,   K18,   K19,   K1A, K1B, K1C,   K1D,   K1E,   K1F }, \
+    { K20, KC_NO, K22,   K23, K24,   K25,   K26, K27,   K28,   K29,   K2A, K2B, K2C,   K2D,   KC_NO, K2F }, \
+    { K30, KC_NO, K32,   K33, K34,   K35,   K36, K37,   K38,   K39,   K3A, K3B, KC_NO, K3D,   K3E,   K3F }, \
+    { K40, K41,   KC_NO, K43, KC_NO, KC_NO, K46, KC_NO, KC_NO, KC_NO, K4A, K4B, K4C,   K4D,   K4E,   K4F }, \
+}
+

keyboards/kbdfans/kbd67/rev2/rules.mk

@@ -0,0 +1,82 @@
+# MCU name
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   atmega32a    bootloadHID
+BOOTLOADER = atmel-dfu
+
+
+# If you don't know the bootloader type, then you can specify the
+# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
+#   Teensy halfKay      512
+#   Teensy++ halfKay    1024
+#   Atmel DFU loader    4096
+#   LUFA bootloader     4096
+#   USBaspLoader        2048
+# OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE = lite     # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = yes        # Console for debug(+400)
+COMMAND_ENABLE = no        # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE = no            # USB Nkey Rollover
+BACKLIGHT_ENABLE = yes       # Enable keyboard backlight functionality on B7 by default
+RGBLIGHT_ENABLE = yes        # Enable keyboard RGB underglow
+MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no           # Audio output on port C6
+FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
+HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)
+
+LAYOUTS = 65_ansi

keyboards/massdrop/ctrl/keymaps/matthewrobo/keymap.c

@@ -1,5 +1,4 @@
 #include QMK_KEYBOARD_H
-extern bool g_suspend_state;
 
 enum ctrl_layers {
 	_QWERTY,
@@ -31,7 +30,6 @@ enum ctrl_keycodes {
 #define TG_NKRO MAGIC_TOGGLE_NKRO //Toggle 6KRO / NKRO mode
 #define LT_CAPS LT(_NAV, KC_CAPS)
 #define _V_V_V_ KC_TRNS
-extern rgb_config_t rgb_matrix_config;
 extern bool autoshift_enabled;
 
 

keyboards/minidox/keymaps/norman/config.h

@@ -0,0 +1,5 @@
+#pragma once
+
+#define PERMISSIVE_HOLD
+#define QMK_KEYS_PER_SCAN 4 
+#define TAPPING_TERM 160

keyboards/minidox/keymaps/norman/keymap.c

@@ -0,0 +1,69 @@
+#include QMK_KEYBOARD_H
+
+#include <sendstring_norman.h>
+
+
+extern keymap_config_t keymap_config;
+
+// Each layer gets a name for readability, which is then used in the keymap matrix below.
+// The underscores don't mean anything - you can have a layer called STUFF or any other name.
+// Layer names don't all need to be of the same length, obviously, and you can also skip them
+// entirely and just use numbers.
+enum layers {
+    _NORMAN,
+    _LOWER,
+    _RAISE,
+    _ADJUST
+};
+
+enum custom_keycodes {
+  QWERTY = SAFE_RANGE,
+  LOWER,
+  RAISE,
+  ADJUST
+};
+
+// Defines for task manager and such
+#define CALTDEL LCTL(LALT(KC_DEL))
+#define TSKMGR LCTL(LSFT(KC_ESC))
+#define DSK_LFT LGUI(LCTL(KC_LEFT))
+#define DSK_RT  LGUI(LCTL(KC_RIGHT))
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+
+[_NORMAN] = LAYOUT( \
+  NM_Q,    NM_W,    NM_D,    NM_F,    NM_K,                       NM_J,    NM_U,    NM_R,    NM_L,    NM_SCLN,    \
+  NM_A,    NM_S,    NM_E,    NM_T,    NM_G,                       NM_Y,    NM_N,    NM_I,    NM_O,    NM_H, \
+  NM_Z,    NM_X,    NM_C,    NM_V,    NM_B,                       NM_P,    NM_M,    NM_COMM, NM_DOT,  NM_SLSH, \
+    LGUI_T(KC_ENT), LT(_RAISE, KC_ESC), SFT_T(KC_BSPC),    CTL_T(KC_SPC), LT(_LOWER, KC_TAB), ALT_T(KC_ENT)    \
+),
+
+[_RAISE] = LAYOUT( \
+  KC_EXLM,    KC_AT,    KC_HASH, KC_DLR,  KC_PERC,      KC_PLUS, KC_7,     KC_8,   KC_9, KC_0,    \
+  KC_CIRC,    KC_AMPR,  KC_TILD, KC_PIPE, KC_BSLS,      KC_MINUS,  KC_4,     KC_5,   KC_6, KC_EQL, \
+  KC_DQT,     KC_QUOT,  KC_UNDS, KC_GRV,  _______,      KC_ASTR,  KC_1,     KC_2,   KC_3, _______, \
+                        _______, _______, _______,      _______,  MO(_ADJUST), _______                    \
+),
+
+
+[_LOWER] = LAYOUT( \
+  KC_ESC,   KC_HOME, KC_UP,   KC_END,   _______,     _______, KC_LPRN, KC_RPRN,  _______, _______,
+  KC_VOLU,  KC_LEFT, KC_DOWN, KC_RIGHT, KC_PGUP,     _______, KC_LBRC, KC_RBRC,  _______, _______, \
+  KC_VOLD,  KC_MPRV, KC_MPLY, KC_MNXT,  KC_PGDN,     _______, KC_LCBR, KC_RCBR,  _______,  _______, \
+                  _______, MO(_ADJUST), _______,      _______,  _______,  _______                    \
+),
+
+[_ADJUST] =  LAYOUT( \
+  KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,        KC_F6,   KC_F7,    KC_F8,   KC_F9,    KC_F10, \
+  _______, DSK_LFT, _______, DSK_RT,  _______,      TSKMGR,  CALTDEL,  _______, KC_F11,   KC_F12, \
+  RESET,   _______, _______, _______, _______,      _______, _______,  _______, _______,  _______, \
+                    _______, _______, _______,      _______, _______,  _______                    \
+)
+
+};
+
+void persistant_default_layer_set(uint16_t default_layer) {
+  eeconfig_update_default_layer(default_layer);
+  default_layer_set(default_layer);
+}

keyboards/minidox/keymaps/norman/readme.md

@@ -0,0 +1,56 @@
+# Minidox Norman Layout by LeHoff
+Based on the QWERTY layout created by Khitsule.
+![lehoff](https://i.imgur.com/rKTdymp.png)
+
+[KLE link](http://www.keyboard-layout-editor.com/#/gists/86ec49f9f820a8b9b36f6e0d2ef8fff7)
+
+## Layers
+| Layer | Legend |
+| ----- | ------ |
+| Base  |  Top left (black) |
+| Lower | Bottom right (red) |
+| Raise | Top right (orange) |
+| Adjust | Front print |
+
+## Features
+* Raise/lower layers focus first on one-handed use
+* Numpad on right hand with raise layer
+* Navigation on left hand with lower layer (ESDF)
+    * D refers to desktop left/right on Win 10 (win+ctrl+left/right)
+* Heavy use of hold/tap dual function keys - from left to right:
+    * Cmd/Enter
+    * Raise/Esc
+    * Shift/Backspace
+    * Ctrl/Space
+    * Lower/Tab
+    * Alt/Enter
+
+
+## Modifier Placement Rationale
+
+There are several major driving forces at play:
+
+* I use MacOS.
+* I'm Danish so the Alt and Shift-Alt layers in MacOS simply have to work.
+* I use Vim for coding.
+* I use org-mode in Emacs to keep track of my time.
+
+* Space is on the right hand side because I almost exclusively use my right hand thumb for
+  space.
+* Cmd is on the left since I often use Cmd+click to open a link in a new tab in Safari.
+* Due to my usage of Vim Esc got a spot on the modifier row.
+* Tab is on the right to enable easy navigation between winows with Cmd+Tab.
+* Shift is on the left since org-mode uses Ctrl+arrows to manipulate task state quickly,
+ and since the arrow keys are activated using Lower (which has been moved to the right) and S, E, T,
+ and D, it works well that way. 
+* Ctrl is on the right since Ctrl+<0-9> is used in MacOS to switch between spaces.
+* Enter is on both sides since Enter is often used together with all of the modifiers. E.g.,
+  Cmd+Enter to send mails in most situations, but Ctrl+Enter is used in Emacs to create a
+  new task in org-mode.
+ 
+This means that arrows and digits are being modified from the other hand, which could be
+bad for gaming, so if you're into that you might want to re-think a few things, but in
+that case you are probably using a Windows machine and then there are other constraints
+you have to deal with.
+
+

keyboards/nek_type_a/config.h

@@ -0,0 +1,55 @@
+/*
+Copyright 2018 Mike Roberts
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0xFEED
+#define PRODUCT_ID      0x0000
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    miker
+#define PRODUCT         nek_type_a
+#define DESCRIPTION     NEK Type A
+
+/* key matrix size */
+#define MATRIX_ROWS 6
+#define MATRIX_COLS 18
+
+/* left columns are all onboard, right columns all on expander */
+#define COL_EXPANDED { false, false, false, false, false, false, false, true, true, true, true, true, true, true, true, true, true, true}
+#define MATRIX_COL_PINS { C6, D7, B5, B6, B7, D6, D3, GPA0, GPA1, GPA2, GPA3, GPA4, GPA5, GPA6, GPA7, GPB0, GPB1, GPB2 }
+#define MATRIX_ROW_PINS { F7, F6, F5, F4, F1, F0 }
+
+#define DIODE_DIRECTION ROW2COL
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCING_DELAY 5
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/* key combination for magic key command */
+#define IS_COMMAND() ( \
+    keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
+)
+
+

keyboards/nek_type_a/keymaps/default/config.h

@@ -0,0 +1,19 @@
+/* Copyright 2018 Mike Roberts
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+
+// place overrides here

keyboards/nek_type_a/keymaps/default/keymap.c

@@ -0,0 +1,39 @@
+/* Copyright 2018 Mike Roberts
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include QMK_KEYBOARD_H
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+  [0] = LAYOUT(
+    KC_ESC, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC__MUTE, KC__VOLDOWN, KC__VOLUP, \
+    KC_GRAVE, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINUS, KC_EQUAL, KC_BSPACE, KC_INSERT, KC_HOME, KC_PGUP, \
+    KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRACKET, KC_RBRACKET, KC_BSLASH, KC_DELETE, KC_END, KC_PGDOWN, \
+    KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCOLON, KC_QUOTE, KC_ENTER, \
+    KC_LSHIFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMMA, KC_DOT, KC_SLASH, KC_RSHIFT, KC_UP, \
+    KC_LCTRL, KC_LALT, KC_LCMD, KC_SPC, KC_SPC, KC_RCMD, KC_RALT, KC_RCTRL, KC_APP, KC_LEFT, KC_DOWN, KC_RIGHT \
+  ),
+};
+
+void matrix_init_user(void) {
+
+}
+
+void matrix_scan_user(void) {
+
+}
+
+void led_set_user(uint8_t usb_led) {
+
+}

keyboards/nek_type_a/keymaps/default/readme.md

@@ -0,0 +1,3 @@
+![NEK Type A Layout](https://i.imgur.com/ElEVvze.png)
+
+# Default NEK Type A Keymap

keyboards/nek_type_a/matrix.c

@@ -0,0 +1,412 @@
+/*
+Copyright 2012-2018 Jun Wako, Jack Humbert, Mike Roberts
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+/*
+ * This matrix.c has been hacked up to support some columns being on an ex pander in ROW2COL mode.
+ * The columns are only ever selected and unselected, never read. Unselecting a single column via the expander is not
+ * implemented because updating one column costs the same as updating all the columns in a bank. Currently both banks
+ * are unselected but two i2c transactions could be removed if we only unselect the the proper half.
+ */
+
+#include <stdint.h>
+#include <stdbool.h>
+#if defined(__AVR__)
+#include <avr/io.h>
+#endif
+#include "wait.h"
+#include "print.h"
+#include "debug.h"
+#include "util.h"
+#include "matrix.h"
+#include "timer.h"
+#include "mcp23017.h"
+#include "outputselect.h"
+
+/* Set 0 if debouncing isn't needed */
+
+#ifndef DEBOUNCING_DELAY
+#   define DEBOUNCING_DELAY 5
+#endif
+
+#if (DEBOUNCING_DELAY > 0)
+    static uint16_t debouncing_time;
+    static bool debouncing = false;
+#endif
+
+#if (MATRIX_COLS <= 8)
+#    define print_matrix_header()  print("\nr/c 01234567\n")
+#    define print_matrix_row(row)  print_bin_reverse8(matrix_get_row(row))
+#    define matrix_bitpop(i)       bitpop(matrix[i])
+#    define ROW_SHIFTER ((uint8_t)1)
+#elif (MATRIX_COLS <= 16)
+#    define print_matrix_header()  print("\nr/c 0123456789ABCDEF\n")
+#    define print_matrix_row(row)  print_bin_reverse16(matrix_get_row(row))
+#    define matrix_bitpop(i)       bitpop16(matrix[i])
+#    define ROW_SHIFTER ((uint16_t)1)
+#elif (MATRIX_COLS <= 32)
+#    define print_matrix_header()  print("\nr/c 0123456789ABCDEF0123456789ABCDEF\n")
+#    define print_matrix_row(row)  print_bin_reverse32(matrix_get_row(row))
+#    define matrix_bitpop(i)       bitpop32(matrix[i])
+#    define ROW_SHIFTER  ((uint32_t)1)
+#endif
+
+#ifdef MATRIX_MASKED
+    extern const matrix_row_t matrix_mask[];
+#endif
+
+#if (DIODE_DIRECTION == ROW2COL) || (DIODE_DIRECTION == COL2ROW)
+static const uint8_t row_pins[MATRIX_ROWS] = MATRIX_ROW_PINS;
+static const uint8_t col_pins[MATRIX_COLS] = MATRIX_COL_PINS;
+static const bool col_expanded[MATRIX_COLS] = COL_EXPANDED;
+#endif
+
+/* matrix state(1:on, 0:off) */
+static matrix_row_t matrix[MATRIX_ROWS];
+
+static matrix_row_t matrix_debouncing[MATRIX_ROWS];
+
+
+#if (DIODE_DIRECTION == COL2ROW)
+    static void init_cols(void);
+    static bool read_cols_on_row(matrix_row_t current_matrix[], uint8_t current_row);
+    static void unselect_rows(void);
+    static void select_row(uint8_t row);
+    static void unselect_row(uint8_t row);
+#elif (DIODE_DIRECTION == ROW2COL)
+    static void init_rows(void);
+    static bool read_rows_on_col(matrix_row_t current_matrix[], uint8_t current_col);
+    static void unselect_cols(void);
+    static void unselect_col(uint8_t col);
+    static void select_col(uint8_t col);
+#endif
+
+__attribute__ ((weak))
+void matrix_init_quantum(void) {
+    expander_init();
+    matrix_init_kb();
+}
+
+__attribute__ ((weak))
+void matrix_scan_quantum(void) {
+    matrix_scan_kb();
+}
+
+__attribute__ ((weak))
+void matrix_init_kb(void) {
+    matrix_init_user();
+}
+
+__attribute__ ((weak))
+void matrix_scan_kb(void) {
+    matrix_scan_user();
+}
+
+__attribute__ ((weak))
+void matrix_init_user(void) {
+}
+
+__attribute__ ((weak))
+void matrix_scan_user(void) {
+}
+
+inline
+uint8_t matrix_rows(void) {
+    return MATRIX_ROWS;
+}
+
+inline
+uint8_t matrix_cols(void) {
+    return MATRIX_COLS;
+}
+
+void matrix_init(void) {
+    // initialize row and col
+#if (DIODE_DIRECTION == COL2ROW)
+    unselect_rows();
+    init_cols();
+#elif (DIODE_DIRECTION == ROW2COL)
+    unselect_cols();
+    init_rows();
+#endif
+
+    // initialize matrix state: all keys off
+    for (uint8_t i=0; i < MATRIX_ROWS; i++) {
+        matrix[i] = 0;
+        matrix_debouncing[i] = 0;
+    }
+
+    matrix_init_quantum();
+    set_output(OUTPUT_AUTO);
+}
+
+uint8_t matrix_scan(void)
+{
+
+#if (DIODE_DIRECTION == COL2ROW)
+
+    // Set row, read cols
+    for (uint8_t current_row = 0; current_row < MATRIX_ROWS; current_row++) {
+#       if (DEBOUNCING_DELAY > 0)
+            bool matrix_changed = read_cols_on_row(matrix_debouncing, current_row);
+
+            if (matrix_changed) {
+                debouncing = true;
+                debouncing_time = timer_read();
+            }
+
+#       else
+            read_cols_on_row(matrix, current_row);
+#       endif
+
+    }
+
+#elif (DIODE_DIRECTION == ROW2COL)
+
+    // Set col, read rows
+    for (uint8_t current_col = 0; current_col < MATRIX_COLS; current_col++) {
+#       if (DEBOUNCING_DELAY > 0)
+            bool matrix_changed = read_rows_on_col(matrix_debouncing, current_col);
+            if (matrix_changed) {
+                debouncing = true;
+                debouncing_time = timer_read();
+            }
+#       else
+             read_rows_on_col(matrix, current_col);
+#       endif
+
+    }
+
+#endif
+
+#   if (DEBOUNCING_DELAY > 0)
+        if (debouncing && (timer_elapsed(debouncing_time) > DEBOUNCING_DELAY)) {
+            for (uint8_t i = 0; i < MATRIX_ROWS; i++) {
+                matrix[i] = matrix_debouncing[i];
+            }
+            debouncing = false;
+        }
+#   endif
+
+    matrix_scan_quantum();
+    return 1;
+}
+
+bool matrix_is_modified(void)
+{
+#if (DEBOUNCING_DELAY > 0)
+    if (debouncing) return false;
+#endif
+    return true;
+}
+
+inline
+bool matrix_is_on(uint8_t row, uint8_t col)
+{
+    return (matrix[row] & ((matrix_row_t)1<col));
+}
+
+inline
+matrix_row_t matrix_get_row(uint8_t row)
+{
+    // Matrix mask lets you disable switches in the returned matrix data. For example, if you have a
+    // switch blocker installed and the switch is always pressed.
+#ifdef MATRIX_MASKED
+    return matrix[row] & matrix_mask[row];
+#else
+    return matrix[row];
+#endif
+}
+
+void matrix_print(void)
+{
+    print_matrix_header();
+
+    for (uint8_t row = 0; row < MATRIX_ROWS; row++) {
+        phex(row); print(": ");
+        print_matrix_row(row);
+        print("\n");
+    }
+}
+
+uint8_t matrix_key_count(void)
+{
+    uint8_t count = 0;
+    for (uint8_t i = 0; i < MATRIX_ROWS; i++) {
+        count += matrix_bitpop(i);
+    }
+    return count;
+}
+
+
+
+#if (DIODE_DIRECTION == COL2ROW)
+
+static void init_cols(void)
+{
+    for(uint8_t x = 0; x < MATRIX_COLS; x++) {
+        uint8_t pin = col_pins[x];
+        _SFR_IO8((pin >> 4) + 1) &= ~_BV(pin & 0xF); // IN
+        _SFR_IO8((pin >> 4) + 2) |=  _BV(pin & 0xF); // HI
+    }
+}
+
+static bool read_cols_on_row(matrix_row_t current_matrix[], uint8_t current_row)
+{
+    // Store last value of row prior to reading
+    matrix_row_t last_row_value = current_matrix[current_row];
+
+    // Clear data in matrix row
+    current_matrix[current_row] = 0;
+
+    // Select row and wait for row selecton to stabilize
+    select_row(current_row);
+    wait_us(30);
+
+    // For each col...
+    for(uint8_t col_index = 0; col_index < MATRIX_COLS; col_index++) {
+
+        // Select the col pin to read (active low)
+        uint8_t pin = col_pins[col_index];
+        uint8_t pin_state = (_SFR_IO8(pin >> 4) & _BV(pin & 0xF));
+
+        // Populate the matrix row with the state of the col pin
+        current_matrix[current_row] |=  pin_state ? 0 : (ROW_SHIFTER << col_index);
+    }
+
+    // Unselect row
+    unselect_row(current_row);
+
+    return (last_row_value != current_matrix[current_row]);
+}
+
+static void select_row(uint8_t row)
+{
+    uint8_t pin = row_pins[row];
+    _SFR_IO8((pin >> 4) + 1) |=  _BV(pin & 0xF); // OUT
+    _SFR_IO8((pin >> 4) + 2) &= ~_BV(pin & 0xF); // LOW
+}
+
+static void unselect_row(uint8_t row)
+{
+    uint8_t pin = row_pins[row];
+    _SFR_IO8((pin >> 4) + 1) &= ~_BV(pin & 0xF); // IN
+    _SFR_IO8((pin >> 4) + 2) |=  _BV(pin & 0xF); // HI
+}
+
+static void unselect_rows(void)
+{
+    for(uint8_t x = 0; x < MATRIX_ROWS; x++) {
+        uint8_t pin = row_pins[x];
+        _SFR_IO8((pin >> 4) + 1) &= ~_BV(pin & 0xF); // IN
+        _SFR_IO8((pin >> 4) + 2) |=  _BV(pin & 0xF); // HI
+    }
+}
+
+#elif (DIODE_DIRECTION == ROW2COL)
+
+static void init_rows(void)
+{
+    for(uint8_t x = 0; x < MATRIX_ROWS; x++) {
+        uint8_t pin = row_pins[x];
+        _SFR_IO8((pin >> 4) + 1) &= ~_BV(pin & 0xF); // IN
+        _SFR_IO8((pin >> 4) + 2) |=  _BV(pin & 0xF); // HI
+    }
+}
+
+static bool read_rows_on_col(matrix_row_t current_matrix[], uint8_t current_col)
+{
+    bool matrix_changed = false;
+
+    // Select col and wait for col selecton to stabilize
+    select_col(current_col);
+    wait_us(30);
+
+    // For each row...
+    for(uint8_t row_index = 0; row_index < MATRIX_ROWS; row_index++)
+    {
+        // Store last value of row prior to reading
+        matrix_row_t last_row_value = current_matrix[row_index];
+
+        // Check row pin state
+        if ((_SFR_IO8(row_pins[row_index] >> 4) & _BV(row_pins[row_index] & 0xF)) == 0)
+        {
+            // Pin LO, set col bit
+            current_matrix[row_index] |= (ROW_SHIFTER << current_col);
+        }
+        else
+        {
+            // Pin HI, clear col bit
+            current_matrix[row_index] &= ~(ROW_SHIFTER << current_col);
+        }
+
+        // Determine if the matrix changed state
+        if ((last_row_value != current_matrix[row_index]) && !(matrix_changed))
+        {
+            matrix_changed = true;
+        }
+    }
+
+    // Unselect col
+    unselect_col(current_col);
+
+    return matrix_changed;
+}
+
+static void select_col(uint8_t col)
+{
+    uint8_t pin = col_pins[col];
+    if (col_expanded[col])
+    {
+        expander_select(pin);
+    }
+    else
+    {
+        _SFR_IO8((pin >> 4) + 1) |=  _BV(pin & 0xF); // OUT
+        _SFR_IO8((pin >> 4) + 2) &= ~_BV(pin & 0xF); // LOW
+    }
+}
+
+
+static void unselect_col(uint8_t col)
+{
+    uint8_t pin = col_pins[col];
+    if (col_expanded[col])
+    {
+        expander_unselect_all();
+    }
+    else
+    {
+        _SFR_IO8((pin >> 4) + 1) &= ~_BV(pin & 0xF); // IN
+        _SFR_IO8((pin >> 4) + 2) |=  _BV(pin & 0xF); // HI
+    }
+}
+
+static void unselect_cols(void)
+{
+    expander_unselect_all();
+
+    for(uint8_t col = 0; col < MATRIX_COLS; col++) {
+        uint8_t pin = col_pins[col];
+        if (!col_expanded[col])
+        {
+            _SFR_IO8((pin >> 4) + 1) &= ~_BV(pin & 0xF); // IN
+            _SFR_IO8((pin >> 4) + 2) |=  _BV(pin & 0xF); // HI
+        }
+    }
+}
+
+#endif

keyboards/nek_type_a/mcp23017.c

@@ -0,0 +1,107 @@
+/* Copyright 2018 Mike Roberts
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include <stdbool.h>
+#include "action.h"
+#include "lib/lufa/LUFA/Drivers/Peripheral/TWI.h"
+#include "lib/lufa/LUFA/Drivers/Peripheral/AVR8/TWI_AVR8.c"
+#include "mcp23017.h"
+#include "debug.h"
+#include "wait.h"
+
+uint8_t bit_for_pin(uint8_t pin);
+
+uint8_t expander_write(uint8_t reg, uint8_t data);
+
+uint8_t expander_read(uint8_t reg, uint8_t *data);
+
+void expander_config(void);
+
+static const char *twi_err_str(uint8_t res) {
+    switch (res) {
+        case TWI_ERROR_NoError:
+            return "OK";
+        case TWI_ERROR_BusFault:
+            return "BUSFAULT";
+        case TWI_ERROR_BusCaptureTimeout:
+            return "BUSTIMEOUT";
+        case TWI_ERROR_SlaveResponseTimeout:
+            return "SLAVETIMEOUT";
+        case TWI_ERROR_SlaveNotReady:
+            return "SLAVENOTREADY";
+        case TWI_ERROR_SlaveNAK:
+            return "SLAVENAK";
+        default:
+            return "UNKNOWN";
+    }
+}
+
+void expander_init(void) {
+    TWI_Init(TWI_BIT_PRESCALE_1, TWI_BITLENGTH_FROM_FREQ(1, 400000));
+}
+
+// set IN and HI
+void expander_unselect_all() {
+    expander_write(EXPANDER_REG_IODIRA, 0xff);
+    expander_write(EXPANDER_REG_IODIRB, 0xff);
+    expander_write(EXPANDER_REG_OLATA, 0xff);
+    expander_write(EXPANDER_REG_OLATB, 0xff);
+    wait_us(EXPANDER_PAUSE);
+}
+
+// set OUT and LOW
+void expander_select(uint8_t pin) {
+    const uint8_t mask = 0xff & ~(1 << bit_for_pin(pin));
+    if (pin < 8) {
+        expander_write(EXPANDER_REG_IODIRA, mask);
+        expander_write(EXPANDER_REG_OLATA, mask);
+    } else {
+        expander_write(EXPANDER_REG_IODIRB, mask);
+        expander_write(EXPANDER_REG_OLATB, mask);
+    }
+    wait_us(EXPANDER_PAUSE);
+}
+
+void expander_config() {
+    // set everything to input
+    expander_write(EXPANDER_REG_IODIRA, 0xff);
+    expander_write(EXPANDER_REG_IODIRB, 0xff);
+
+    // turn on pull-ups
+    expander_write(EXPANDER_REG_GPPUA, 0xff);
+    expander_write(EXPANDER_REG_GPPUB, 0xff);
+
+    // disable interrupts
+    expander_write(EXPANDER_REG_GPINTENA, 0x0);
+    expander_write(EXPANDER_REG_GPINTENB, 0x0);
+
+    // polarity
+    expander_write(EXPANDER_REG_IPOLA, 0x0);
+    expander_write(EXPANDER_REG_IPOLB, 0x0);
+}
+
+uint8_t bit_for_pin(uint8_t pin) {
+    return pin % 8;
+}
+
+uint8_t expander_write(uint8_t reg, unsigned char val) {
+    uint8_t addr = reg;
+    uint8_t result = TWI_WritePacket(EXPANDER_ADDR << 1, I2C_TIMEOUT, &addr, sizeof(addr), &val, sizeof(val));
+    if (result) {
+        xprintf("mcp: set_register %d = %d failed: %s\n", reg, val, twi_err_str(result));
+    }
+    return result == 0;
+}
+

keyboards/nek_type_a/mcp23017.h

@@ -0,0 +1,71 @@
+/* Copyright 2018 Mike Roberts
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#ifndef MAP23017_H
+#define MAP23017_H
+
+#define EXPANDER_ADDR 0x27
+#define I2C_TIMEOUT 200 // milliseconds
+#define EXPANDER_PAUSE 0 // microseconds
+
+enum EXPANDER_REGISTERS {
+    EXPANDER_REG_IODIRA = 0x00,
+    EXPANDER_REG_IODIRB = 0x01,
+    EXPANDER_REG_IPOLA = 0x02,
+    EXPANDER_REG_IPOLB = 0x03,
+    EXPANDER_REG_GPINTENA = 0x04,
+    EXPANDER_REG_GPINTENB = 0x05,
+    EXPANDER_REG_DEFVALA = 0x06,
+    EXPANDER_REG_DEFVALB = 0x07,
+    EXPANDER_REG_INTCONA = 0x08,
+    EXPANDER_REG_INTCONB = 0x09,
+    EXPANDER_REG_IOCONA = 0x0A,
+    EXPANDER_REG_IOCONB = 0x0B,
+    EXPANDER_REG_GPPUA = 0x0C,
+    EXPANDER_REG_GPPUB = 0x0D,
+    EXPANDER_REG_INTFA = 0x0E,
+    EXPANDER_REG_INTFB = 0x0F,
+    EXPANDER_REG_INTCAPA = 0x10,
+    EXPANDER_REG_INTCAPB = 0x11,
+    EXPANDER_REG_GPIOA = 0x12,
+    EXPANDER_REG_GPIOB = 0x13,
+    EXPANDER_REG_OLATA = 0x14,
+    EXPANDER_REG_OLATB = 0x15
+};
+
+#define GPA0 0x0
+#define GPA1 0x1
+#define GPA2 0x2
+#define GPA3 0x3
+#define GPA4 0x4
+#define GPA5 0x5
+#define GPA6 0x6
+#define GPA7 0x7
+#define GPB0 0x8
+#define GPB1 0x9
+#define GPB2 0xA
+#define GPB3 0xB
+#define GPB4 0xC
+#define GPB5 0xD
+#define GPB6 0xE
+#define GPB7 0xF
+
+
+void expander_init(void);
+void expander_select(uint8_t pin);
+void expander_unselect(uint8_t pin);
+void expander_unselect_all(void);
+
+#endif

keyboards/nek_type_a/nek_type_a.c

@@ -0,0 +1,43 @@
+/* Copyright 2018 Mike Roberts
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include "nek_type_a.h"
+
+void matrix_init_kb(void) {
+	// put your keyboard start-up code here
+	// runs once when the firmware starts up
+
+	matrix_init_user();
+}
+
+void matrix_scan_kb(void) {
+	// put your looping keyboard code here
+	// runs every cycle (a lot)
+
+	matrix_scan_user();
+}
+
+bool process_record_kb(uint16_t keycode, keyrecord_t *record) {
+	// put your per-action keyboard code here
+	// runs for every action, just before processing by the firmware
+
+	return process_record_user(keycode, record);
+}
+
+void led_set_kb(uint8_t usb_led) {
+	// put your keyboard LED indicator (ex: Caps Lock LED) toggling code here
+
+	led_set_user(usb_led);
+}

keyboards/nek_type_a/nek_type_a.h

@@ -0,0 +1,58 @@
+/* Copyright 2018 REPLACE_WITH_YOUR_NAME
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#ifndef NEK_TYPE_A_H
+#define NEK_TYPE_A_H
+
+#include "quantum.h"
+#include <stdint.h>
+#include <stdbool.h>
+#include <util/delay.h>
+
+#define I2C_ADDR        0b0100000
+#define I2C_ADDR_WRITE  ( (I2C_ADDR<<1) | I2C_WRITE )
+#define I2C_ADDR_READ   ( (I2C_ADDR<<1) | I2C_READ  )
+#define IODIRA          0x00            // i/o direction register
+#define IODIRB          0x01
+#define GPPUA           0x0C            // GPIO pull-up resistor register
+#define GPPUB           0x0D
+#define GPIOA           0x12            // general purpose i/o port register (write modifies OLAT)
+#define GPIOB           0x13
+#define OLATA           0x14            // output latch register
+#define OLATB           0x15
+
+extern uint8_t expander_status;
+extern uint8_t expander_input_pin_mask;
+extern bool i2c_initialized;
+
+void init_expander(void);
+
+#define LAYOUT( \
+         L12,      L14, L15, L16, L17,   R11, R12, R13, R14, R15, R16, R17, R18, R19, R1A, R1B, \
+    L21, L22, L23, L24, L25, L26, L27,   R21, R22, R23, R24, R25, R26,      R28, R29, R2A, R2B, \
+    L31, L32, L33, L34, L35, L36,        R31, R32, R33, R34, R35, R36, R37, R38, R39, R3A, R3B, \
+    L41, L42, L43, L44, L45, L46,        R41, R42, R43, R44, R45, R46,      R48,                \
+    L51, L52, L53, L54, L55, L56,        R51, R52, R53, R54, R55,           R58,      R5A,      \
+    L61, L62, L63,      L65,             R61,      R63,      R65, R66,      R68, R69, R6A, R6B  \
+) \
+{ \
+    { KC_NO,   L12, KC_NO,   L14,   L15,   L16,   L17,   R11,   R12,   R13,   R14,   R15,   R16,   R17,   R18,   R19,   R1A,   R1B }, \
+    {   L21,   L22,   L23,   L24,   L25,   L26,   L27,   R21,   R22,   R23,   R24,   R25,   R26, KC_NO,   R28,   R29,   R2A,   R2B }, \
+    {   L31,   L32,   L33,   L34,   L35,   L36, KC_NO,   R31,   R32,   R33,   R34,   R35,   R36,   R37,   R38,   R39,   R3A,   R3B }, \
+    {   L41,   L42,   L43,   L44,   L45,   L46, KC_NO,   R41,   R42,   R43,   R44,   R45,   R46, KC_NO,   R48, KC_NO, KC_NO, KC_NO }, \
+    {   L51,   L52,   L53,   L54,   L55,   L56, KC_NO,   R51,   R52,   R53,   R54,   R55, KC_NO, KC_NO,   R58, KC_NO,   R5A, KC_NO }, \
+    {   L61,   L62,   L63, KC_NO,   L65, KC_NO, KC_NO,   R61, KC_NO,   R63, KC_NO,   R65,   R66, KC_NO,   R68,   R69,   R6A,   R6B }, \
+}
+#endif

keyboards/nek_type_a/readme.md

@@ -0,0 +1,30 @@
+# nek_type_a
+
+![NEK Type A Keyboard](https://i.imgur.com/XFnjlQ9.jpg)
+
+Natural Ergonomic Keyboard, Type A
+
+Keyboard Maintainer: [Mike Roberts](https://github.com/ecopoesis)  
+Hardware Supported: Custom PCBs from https://github.com/ecopoesis/nek-type-a  
+Hardware Availability: https://github.com/ecopoesis/nek-type-a  
+
+## Design
+
+This is a column-driven split keyboard using three custom PCBs connected with ribbon cables. The left and right PCBs are
+passive: they only have the diodes and switches needed to make the matrix. The center PCB has an Adafruit Feather 32u4 and
+MCP23017 expander.
+
+The left matrix has its rows and columns directly connected to the Feather. The right matrix has its rows connect to the
+Feather (using the same pins as the left matrix) and its columns connected to the expander. The expander uses the LUFA
+hardware TWI driver.
+
+Bluetooth is enabled.
+
+## Building
+
+Make and install this keyboard (after setting up your build environment):
+```
+make nek_type_a:default:avrdude
+```
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/nek_type_a/rules.mk

@@ -0,0 +1,33 @@
+SRC = matrix.c mcp23017.c
+
+MCU = atmega32u4
+F_CPU = 8000000
+
+ARCH = AVR8
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+BOOTLOADER = caterina
+
+BOOTMAGIC_ENABLE = no       # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = no       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = yes        # Console for debug(+400)
+COMMAND_ENABLE = yes        # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE = no            # USB Nkey Rollover
+BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality on B7 by default
+RGBLIGHT_ENABLE = no        # Enable keyboard RGB underglow
+MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = yes      # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no           # Audio output on port C6
+FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
+HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)
+CUSTOM_MATRIX = yes
+DEBUG_ENABLE = yes
+BLUETOOTH = AdafruitBLE

keyboards/noxary/220/220.c

@@ -0,0 +1,62 @@
+/* Copyright 2019 MechMerlin
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include "220.h"
+
+// Optional override functions below.
+// You can leave any or all of these undefined.
+// These are only required if you want to perform custom actions.
+
+void matrix_init_kb(void) {
+  // put your keyboard start-up code here
+  // runs once when the firmware starts up
+  setPinOutput(C6);
+  matrix_init_user();
+}
+
+
+/*
+
+void matrix_scan_kb(void) {
+  // put your looping keyboard code here
+  // runs every cycle (a lot)
+
+  matrix_scan_user();
+}
+
+bool process_record_kb(uint16_t keycode, keyrecord_t *record) {
+  // put your per-action keyboard code here
+  // runs for every action, just before processing by the firmware
+
+  return process_record_user(keycode, record);
+}
+
+void led_set_kb(uint8_t usb_led) {
+  // put your keyboard LED indicator (ex: Caps Lock LED) toggling code here
+
+  led_set_user(usb_led);
+}
+
+*/
+
+void led_set_kb(uint8_t usb_led) {
+	// put your keyboard LED indicator (ex: Caps Lock LED) toggling code here
+  if (IS_LED_ON(usb_led, USB_LED_NUM_LOCK)) {
+    writePinLow(C6);
+  } else {
+    writePinHigh(C6);
+  }
+	led_set_user(usb_led);
+}

keyboards/noxary/220/220.h

@@ -0,0 +1,42 @@
+/* Copyright 2019 MechMerlin
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#pragma once
+
+#include "quantum.h"
+
+/* This a shortcut to help you visually see your layout.
+ *
+ * The first section contains all of the arguments representing the physical
+ * layout of the board and position of the keys.
+ *
+ * The second converts the arguments into a two-dimensional array which
+ * represents the switch matrix.
+ */
+#define LAYOUT_ortho_6x4( \
+	K00, K01, K02, K03, \
+	K10, K11, K12, K13, \
+	K20, K21, K22, K23, \
+	K30, K31, K32, K33, \
+	K40, K41, K42, K43, \
+	K50, K51, K52, K53  \
+) { \
+	{ K00,   K01,   K02,   K03 }, \
+	{ K10,   K11,   K12,   K13 }, \
+	{ K20,   K21,   K22,   K23 }, \
+	{ K30,   K31,   K32,   K33 }, \
+	{ K40,   K41,   K42,   K43 }, \
+	{ K50,   K51,   K52,   K53 }  \
+}

keyboards/noxary/220/config.h

@@ -0,0 +1,251 @@
+/*
+Copyright 2019 MechMerlin
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0xFEED
+#define PRODUCT_ID      0x6060
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    Noxary
+#define PRODUCT         220
+#define DESCRIPTION     A custom numpad
+
+/* key matrix size */
+#define MATRIX_ROWS 6
+#define MATRIX_COLS 4
+
+/*
+ * Keyboard Matrix Assignments
+ *
+ * Change this to how you wired your keyboard
+ * COLS: AVR pins used for columns, left to right
+ * ROWS: AVR pins used for rows, top to bottom
+ * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
+ *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
+ *
+*/
+#define MATRIX_ROW_PINS { C4, B0, D3, D4, D5, D6 }
+#define MATRIX_COL_PINS { B4, C5, D2, D1 }
+#define UNUSED_PINS
+
+/* COL2ROW, ROW2COL*/
+#define DIODE_DIRECTION COL2ROW
+
+/*
+ * Split Keyboard specific options, make sure you have 'SPLIT_KEYBOARD = yes' in your rules.mk, and define SOFT_SERIAL_PIN.
+ */
+#define SOFT_SERIAL_PIN D0 // or D1, D2, D3, E6
+
+#define BACKLIGHT_PIN B7
+#define BACKLIGHT_BREATHING
+#define BACKLIGHT_LEVELS 3
+
+// #define RGB_DI_PIN E2
+// #ifdef RGB_DI_PIN
+//   #define RGBLED_NUM 16
+//   #define RGBLIGHT_HUE_STEP 8
+//   #define RGBLIGHT_SAT_STEP 8
+//   #define RGBLIGHT_VAL_STEP 8
+//   #define RGBLIGHT_LIMIT_VAL 255 /* The maximum brightness level */
+//   #define RGBLIGHT_SLEEP  /* If defined, the RGB lighting will be switched off when the host goes to sleep */
+// /*== all animations enable ==*/
+//   #define RGBLIGHT_ANIMATIONS
+// /*== or choose animations ==*/
+//   #define RGBLIGHT_EFFECT_BREATHING
+//   #define RGBLIGHT_EFFECT_RAINBOW_MOOD
+//   #define RGBLIGHT_EFFECT_RAINBOW_SWIRL
+//   #define RGBLIGHT_EFFECT_SNAKE
+//   #define RGBLIGHT_EFFECT_KNIGHT
+//   #define RGBLIGHT_EFFECT_CHRISTMAS
+//   #define RGBLIGHT_EFFECT_STATIC_GRADIENT
+//   #define RGBLIGHT_EFFECT_RGB_TEST
+//   #define RGBLIGHT_EFFECT_ALTERNATING
+// /*== customize breathing effect ==*/
+//   /*==== (DEFAULT) use fixed table instead of exp() and sin() ====*/
+//   #define RGBLIGHT_BREATHE_TABLE_SIZE 256      // 256(default) or 128 or 64
+//   /*==== use exp() and sin() ====*/
+//   #define RGBLIGHT_EFFECT_BREATHE_CENTER 1.85  // 1 to 2.7
+//   #define RGBLIGHT_EFFECT_BREATHE_MAX    255   // 0 to 255
+// #endif
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCING_DELAY 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/* If defined, GRAVE_ESC will always act as ESC when CTRL is held.
+ * This is userful for the Windows task manager shortcut (ctrl+shift+esc).
+ */
+// #define GRAVE_ESC_CTRL_OVERRIDE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/* key combination for magic key command */
+/* defined by default; to change, uncomment and set to the combination you want */
+// #define IS_COMMAND() (get_mods() == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)))
+
+/* control how magic key switches layers */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
+
+/* override magic key keymap */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
+//#define MAGIC_KEY_HELP           H
+//#define MAGIC_KEY_HELP_ALT       SLASH
+//#define MAGIC_KEY_DEBUG          D
+//#define MAGIC_KEY_DEBUG_MATRIX   X
+//#define MAGIC_KEY_DEBUG_KBD      K
+//#define MAGIC_KEY_DEBUG_MOUSE    M
+//#define MAGIC_KEY_VERSION        V
+//#define MAGIC_KEY_STATUS         S
+//#define MAGIC_KEY_CONSOLE        C
+//#define MAGIC_KEY_LAYER0         0
+//#define MAGIC_KEY_LAYER0_ALT     GRAVE
+//#define MAGIC_KEY_LAYER1         1
+//#define MAGIC_KEY_LAYER2         2
+//#define MAGIC_KEY_LAYER3         3
+//#define MAGIC_KEY_LAYER4         4
+//#define MAGIC_KEY_LAYER5         5
+//#define MAGIC_KEY_LAYER6         6
+//#define MAGIC_KEY_LAYER7         7
+//#define MAGIC_KEY_LAYER8         8
+//#define MAGIC_KEY_LAYER9         9
+//#define MAGIC_KEY_BOOTLOADER     B
+//#define MAGIC_KEY_BOOTLOADER_ALT ESC
+//#define MAGIC_KEY_LOCK           CAPS
+//#define MAGIC_KEY_EEPROM         E
+//#define MAGIC_KEY_EEPROM_CLEAR   BSPACE
+//#define MAGIC_KEY_NKRO           N
+//#define MAGIC_KEY_SLEEP_LED      Z
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+/*
+ * MIDI options
+ */
+
+/* Prevent use of disabled MIDI features in the keymap */
+//#define MIDI_ENABLE_STRICT 1
+
+/* enable basic MIDI features:
+   - MIDI notes can be sent when in Music mode is on
+*/
+//#define MIDI_BASIC
+
+/* enable advanced MIDI features:
+   - MIDI notes can be added to the keymap
+   - Octave shift and transpose
+   - Virtual sustain, portamento, and modulation wheel
+   - etc.
+*/
+//#define MIDI_ADVANCED
+
+/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
+//#define MIDI_TONE_KEYCODE_OCTAVES 1
+
+/*
+ * HD44780 LCD Display Configuration
+ */
+/*
+#define LCD_LINES           2     //< number of visible lines of the display
+#define LCD_DISP_LENGTH    16     //< visibles characters per line of the display
+
+#define LCD_IO_MODE      1            //< 0: memory mapped mode, 1: IO port mode
+
+#if LCD_IO_MODE
+#define LCD_PORT         PORTB        //< port for the LCD lines
+#define LCD_DATA0_PORT   LCD_PORT     //< port for 4bit data bit 0
+#define LCD_DATA1_PORT   LCD_PORT     //< port for 4bit data bit 1
+#define LCD_DATA2_PORT   LCD_PORT     //< port for 4bit data bit 2
+#define LCD_DATA3_PORT   LCD_PORT     //< port for 4bit data bit 3
+#define LCD_DATA0_PIN    4            //< pin for 4bit data bit 0
+#define LCD_DATA1_PIN    5            //< pin for 4bit data bit 1
+#define LCD_DATA2_PIN    6            //< pin for 4bit data bit 2
+#define LCD_DATA3_PIN    7            //< pin for 4bit data bit 3
+#define LCD_RS_PORT      LCD_PORT     //< port for RS line
+#define LCD_RS_PIN       3            //< pin  for RS line
+#define LCD_RW_PORT      LCD_PORT     //< port for RW line
+#define LCD_RW_PIN       2            //< pin  for RW line
+#define LCD_E_PORT       LCD_PORT     //< port for Enable line
+#define LCD_E_PIN        1            //< pin  for Enable line
+#endif
+*/
+
+/* Bootmagic Lite key configuration */
+// #define BOOTMAGIC_LITE_ROW 0
+// #define BOOTMAGIC_LITE_COLUMN 0

keyboards/noxary/220/info.json

@@ -0,0 +1,12 @@
+{
+    "keyboard_name": "Noxary 220", 
+    "url": "", 
+    "maintainer": "qmk", 
+    "width": 4, 
+    "height": 6.5, 
+    "layouts": {
+        "LAYOUT_ortho_6x4": {
+            "layout": [{"x":0, "y":0}, {"x":1, "y":0}, {"x":2, "y":0}, {"x":3, "y":0}, {"x":0, "y":1.5}, {"x":1, "y":1.5}, {"x":2, "y":1.5}, {"x":3, "y":1.5}, {"x":0, "y":2.5}, {"x":1, "y":2.5}, {"x":2, "y":2.5}, {"x":3, "y":2.5}, {"x":0, "y":3.5}, {"x":1, "y":3.5}, {"x":2, "y":3.5}, {"x":3, "y":3.5}, {"x":0, "y":4.5}, {"x":1, "y":4.5}, {"x":2, "y":4.5}, {"x":3, "y":4.5}, {"x":0, "y":5.5}, {"x":1, "y":5.5}, {"x":2, "y":5.5}, {"x":3, "y":5.5}]
+        }
+    }
+}

keyboards/noxary/220/keymaps/default/config.h

@@ -0,0 +1,19 @@
+/* Copyright 2019 MechMerlin
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+
+// place overrides here

keyboards/noxary/220/keymaps/default/keymap.c

@@ -0,0 +1,76 @@
+/* Copyright 2019 Rozakiin
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include QMK_KEYBOARD_H
+
+// Defines the keycodes used by our macros in process_record_user
+enum custom_keycodes {
+  QMKBEST = SAFE_RANGE,
+  QMKURL
+};
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+	LAYOUT_ortho_6x4(
+		KC_ESC, BL_TOGG, BL_DEC, BL_INC, 
+		KC_NLCK, KC_SLSH, KC_ASTR, KC_PEQL, 
+		KC_7, KC_8, KC_9, KC_PMNS, 
+		KC_4, KC_5, KC_6, KC_PPLS, 
+		KC_1, KC_2, KC_3, KC_PENT, 
+		KC_0, KC_0, KC_DEL, KC_PENT),
+
+	LAYOUT_ortho_6x4(
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, 
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, 
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, 
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, 
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, 
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS),
+
+};
+
+bool process_record_user(uint16_t keycode, keyrecord_t *record) {
+  switch (keycode) {
+    case QMKBEST:
+      if (record->event.pressed) {
+        // when keycode QMKBEST is pressed
+        SEND_STRING("QMK is the best thing ever!");
+      } else {
+        // when keycode QMKBEST is released
+      }
+      break;
+    case QMKURL:
+      if (record->event.pressed) {
+        // when keycode QMKURL is pressed
+        SEND_STRING("https://qmk.fm/" SS_TAP(X_ENTER));
+      } else {
+        // when keycode QMKURL is released
+      }
+      break;
+  }
+  return true;
+}
+
+void matrix_init_user(void) {
+
+}
+
+void matrix_scan_user(void) {
+
+}
+
+void led_set_user(uint8_t usb_led) {
+
+}

keyboards/noxary/220/keymaps/default/readme.md

@@ -0,0 +1 @@
+# The default keymap for Noxary 220

keyboards/noxary/220/readme.md

@@ -0,0 +1,13 @@
+# Noxary 220
+
+A fully customizable numpad
+
+Keyboard Maintainer: [MechMerlin](https://github.com/mechmerlin), [Rozakiin](https://github.com/rozakiin)    
+Hardware Supported: Noxary 220 PCB  
+Hardware Availability: [Geekhack Group Buy](https://geekhack.org/index.php?topic=95660.0)  
+
+Make example for this keyboard (after setting up your build environment):
+
+    make noxary/220:default
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/noxary/220/rules.mk

@@ -0,0 +1,83 @@
+# MCU name
+#MCU = at90usb1286
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   atmega32a    bootloadHID
+BOOTLOADER = atmel-dfu
+
+
+# If you don't know the bootloader type, then you can specify the
+# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
+#   Teensy halfKay      512
+#   Teensy++ halfKay    1024
+#   Atmel DFU loader    4096
+#   LUFA bootloader     4096
+#   USBaspLoader        2048
+# OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE = lite      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = yes        # Console for debug(+400)
+COMMAND_ENABLE = yes        # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE = no            # USB Nkey Rollover
+BACKLIGHT_ENABLE = yes       # Enable keyboard backlight functionality on B7 by default
+RGBLIGHT_ENABLE = no        # Enable keyboard RGB underglow
+MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no           # Audio output on port C6
+FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
+HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)
+
+LAYOUTS = ortho_6x4

keyboards/noxary/260/260.c

@@ -0,0 +1,61 @@
+/* Copyright 2019 MechMerlin
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include "260.h"
+
+// Optional override functions below.
+// You can leave any or all of these undefined.
+// These are only required if you want to perform custom actions.
+
+
+void matrix_init_kb(void) {
+	// put your keyboard start-up code here
+	// runs once when the firmware starts up
+  setPinOutput(B1);
+	matrix_init_user();
+}
+
+/*
+void matrix_scan_kb(void) {
+  // put your looping keyboard code here
+  // runs every cycle (a lot)
+
+  matrix_scan_user();
+}
+
+bool process_record_kb(uint16_t keycode, keyrecord_t *record) {
+  // put your per-action keyboard code here
+  // runs for every action, just before processing by the firmware
+
+  return process_record_user(keycode, record);
+}
+
+void led_set_kb(uint8_t usb_led) {
+  // put your keyboard LED indicator (ex: Caps Lock LED) toggling code here
+
+  led_set_user(usb_led);
+}
+
+*/
+
+void led_set_kb(uint8_t usb_led) {
+  if (IS_LED_ON(usb_led, USB_LED_CAPS_LOCK)) {
+    writePinLow(B1);
+  } else {
+    writePinHigh(B1);
+  }
+
+	led_set_user(usb_led);
+}

keyboards/noxary/260/260.h

@@ -0,0 +1,40 @@
+/* Copyright 2019 MechMerlin
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#pragma once
+
+#include "quantum.h"
+
+/* This a shortcut to help you visually see your layout.
+ *
+ * The first section contains all of the arguments representing the physical
+ * layout of the board and position of the keys.
+ *
+ * The second converts the arguments into a two-dimensional array which
+ * represents the switch matrix.
+ */
+#define LAYOUT( \
+	K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014, \
+	K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112,       K114, \
+	K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212,       K214, \
+	K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312,       K314, \
+	K400, K401, K402,                   K406,                   K410, K411, K412,       K414  \
+) { \
+	{ K000,  K001,  K002,  K003,  K004,  K005,  K006,  K007,  K008,  K009,  K010,  K011,  K012,  K013,  K014 }, \
+	{ K100,  K101,  K102,  K103,  K104,  K105,  K106,  K107,  K108,  K109,  K110,  K111,  K112,  KC_NO, K114 }, \
+	{ K200,  K201,  K202,  K203,  K204,  K205,  K206,  K207,  K208,  K209,  K210,  K211,  K212,  KC_NO, K214 }, \
+	{ K300,  K301,  K302,  K303,  K304,  K305,  K306,  K307,  K308,  K309,  K310,  K311,  K312,  KC_NO, K314 }, \
+	{ K400,  K401,  K402,  KC_NO, KC_NO, KC_NO, K406,  KC_NO, KC_NO, KC_NO, K410,  K411,  K412,  KC_NO, K414 }  \
+}

keyboards/noxary/260/config.h

@@ -0,0 +1,251 @@
+/*
+Copyright 2019 MechMerlin
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0x4E58
+#define PRODUCT_ID      0x003C
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    Noxary
+#define PRODUCT         260
+#define DESCRIPTION     A custom 60% keyboard
+
+/* key matrix size */
+#define MATRIX_ROWS 5
+#define MATRIX_COLS 15
+
+/*
+ * Keyboard Matrix Assignments
+ *
+ * Change this to how you wired your keyboard
+ * COLS: AVR pins used for columns, left to right
+ * ROWS: AVR pins used for rows, top to bottom
+ * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
+ *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
+ *
+*/
+#define MATRIX_ROW_PINS { F7, F6, F5, F0, B5 }
+#define MATRIX_COL_PINS { C7, C6, B6, F4, E6, D0, B4, D1, D2, D3, D7, D6, D4, F1, D5 }
+#define UNUSED_PINS
+
+/* COL2ROW, ROW2COL*/
+#define DIODE_DIRECTION COL2ROW
+
+/*
+ * Split Keyboard specific options, make sure you have 'SPLIT_KEYBOARD = yes' in your rules.mk, and define SOFT_SERIAL_PIN.
+ */
+#define SOFT_SERIAL_PIN D0 // or D1, D2, D3, E6
+
+#define BACKLIGHT_PIN B7
+#define BACKLIGHT_BREATHING
+#define BACKLIGHT_LEVELS 3
+
+// #define RGB_DI_PIN E2
+// #ifdef RGB_DI_PIN
+//   #define RGBLED_NUM 16
+//   #define RGBLIGHT_HUE_STEP 8
+//   #define RGBLIGHT_SAT_STEP 8
+//   #define RGBLIGHT_VAL_STEP 8
+//   #define RGBLIGHT_LIMIT_VAL 255 /* The maximum brightness level */
+//   #define RGBLIGHT_SLEEP  /* If defined, the RGB lighting will be switched off when the host goes to sleep */
+// /*== all animations enable ==*/
+//   #define RGBLIGHT_ANIMATIONS
+// /*== or choose animations ==*/
+//   #define RGBLIGHT_EFFECT_BREATHING
+//   #define RGBLIGHT_EFFECT_RAINBOW_MOOD
+//   #define RGBLIGHT_EFFECT_RAINBOW_SWIRL
+//   #define RGBLIGHT_EFFECT_SNAKE
+//   #define RGBLIGHT_EFFECT_KNIGHT
+//   #define RGBLIGHT_EFFECT_CHRISTMAS
+//   #define RGBLIGHT_EFFECT_STATIC_GRADIENT
+//   #define RGBLIGHT_EFFECT_RGB_TEST
+//   #define RGBLIGHT_EFFECT_ALTERNATING
+// /*== customize breathing effect ==*/
+//   /*==== (DEFAULT) use fixed table instead of exp() and sin() ====*/
+//   #define RGBLIGHT_BREATHE_TABLE_SIZE 256      // 256(default) or 128 or 64
+//   /*==== use exp() and sin() ====*/
+//   #define RGBLIGHT_EFFECT_BREATHE_CENTER 1.85  // 1 to 2.7
+//   #define RGBLIGHT_EFFECT_BREATHE_MAX    255   // 0 to 255
+// #endif
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCING_DELAY 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/* If defined, GRAVE_ESC will always act as ESC when CTRL is held.
+ * This is userful for the Windows task manager shortcut (ctrl+shift+esc).
+ */
+// #define GRAVE_ESC_CTRL_OVERRIDE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/* key combination for magic key command */
+/* defined by default; to change, uncomment and set to the combination you want */
+// #define IS_COMMAND() (get_mods() == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)))
+
+/* control how magic key switches layers */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
+
+/* override magic key keymap */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
+//#define MAGIC_KEY_HELP           H
+//#define MAGIC_KEY_HELP_ALT       SLASH
+//#define MAGIC_KEY_DEBUG          D
+//#define MAGIC_KEY_DEBUG_MATRIX   X
+//#define MAGIC_KEY_DEBUG_KBD      K
+//#define MAGIC_KEY_DEBUG_MOUSE    M
+//#define MAGIC_KEY_VERSION        V
+//#define MAGIC_KEY_STATUS         S
+//#define MAGIC_KEY_CONSOLE        C
+//#define MAGIC_KEY_LAYER0         0
+//#define MAGIC_KEY_LAYER0_ALT     GRAVE
+//#define MAGIC_KEY_LAYER1         1
+//#define MAGIC_KEY_LAYER2         2
+//#define MAGIC_KEY_LAYER3         3
+//#define MAGIC_KEY_LAYER4         4
+//#define MAGIC_KEY_LAYER5         5
+//#define MAGIC_KEY_LAYER6         6
+//#define MAGIC_KEY_LAYER7         7
+//#define MAGIC_KEY_LAYER8         8
+//#define MAGIC_KEY_LAYER9         9
+//#define MAGIC_KEY_BOOTLOADER     B
+//#define MAGIC_KEY_BOOTLOADER_ALT ESC
+//#define MAGIC_KEY_LOCK           CAPS
+//#define MAGIC_KEY_EEPROM         E
+//#define MAGIC_KEY_EEPROM_CLEAR   BSPACE
+//#define MAGIC_KEY_NKRO           N
+//#define MAGIC_KEY_SLEEP_LED      Z
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+/*
+ * MIDI options
+ */
+
+/* Prevent use of disabled MIDI features in the keymap */
+//#define MIDI_ENABLE_STRICT 1
+
+/* enable basic MIDI features:
+   - MIDI notes can be sent when in Music mode is on
+*/
+//#define MIDI_BASIC
+
+/* enable advanced MIDI features:
+   - MIDI notes can be added to the keymap
+   - Octave shift and transpose
+   - Virtual sustain, portamento, and modulation wheel
+   - etc.
+*/
+//#define MIDI_ADVANCED
+
+/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
+//#define MIDI_TONE_KEYCODE_OCTAVES 1
+
+/*
+ * HD44780 LCD Display Configuration
+ */
+/*
+#define LCD_LINES           2     //< number of visible lines of the display
+#define LCD_DISP_LENGTH    16     //< visibles characters per line of the display
+
+#define LCD_IO_MODE      1            //< 0: memory mapped mode, 1: IO port mode
+
+#if LCD_IO_MODE
+#define LCD_PORT         PORTB        //< port for the LCD lines
+#define LCD_DATA0_PORT   LCD_PORT     //< port for 4bit data bit 0
+#define LCD_DATA1_PORT   LCD_PORT     //< port for 4bit data bit 1
+#define LCD_DATA2_PORT   LCD_PORT     //< port for 4bit data bit 2
+#define LCD_DATA3_PORT   LCD_PORT     //< port for 4bit data bit 3
+#define LCD_DATA0_PIN    4            //< pin for 4bit data bit 0
+#define LCD_DATA1_PIN    5            //< pin for 4bit data bit 1
+#define LCD_DATA2_PIN    6            //< pin for 4bit data bit 2
+#define LCD_DATA3_PIN    7            //< pin for 4bit data bit 3
+#define LCD_RS_PORT      LCD_PORT     //< port for RS line
+#define LCD_RS_PIN       3            //< pin  for RS line
+#define LCD_RW_PORT      LCD_PORT     //< port for RW line
+#define LCD_RW_PIN       2            //< pin  for RW line
+#define LCD_E_PORT       LCD_PORT     //< port for Enable line
+#define LCD_E_PIN        1            //< pin  for Enable line
+#endif
+*/
+
+/* Bootmagic Lite key configuration */
+// #define BOOTMAGIC_LITE_ROW 0
+// #define BOOTMAGIC_LITE_COLUMN 0

keyboards/noxary/260/info.json

@@ -0,0 +1,12 @@
+{
+    "keyboard_name": "Noxary 260", 
+    "url": "", 
+    "maintainer": "qmk", 
+    "width": 15, 
+    "height": 5, 
+    "layouts": {
+        "LAYOUT": {
+            "layout": [{"x":0, "y":0}, {"x":1, "y":0}, {"x":2, "y":0}, {"x":3, "y":0}, {"x":4, "y":0}, {"x":5, "y":0}, {"x":6, "y":0}, {"x":7, "y":0}, {"x":8, "y":0}, {"x":9, "y":0}, {"x":10, "y":0}, {"x":11, "y":0}, {"x":12, "y":0}, {"x":13, "y":0}, {"x":14, "y":0}, {"x":0, "y":1, "w":1.5}, {"x":1.5, "y":1}, {"x":2.5, "y":1}, {"x":3.5, "y":1}, {"x":4.5, "y":1}, {"x":5.5, "y":1}, {"x":6.5, "y":1}, {"x":7.5, "y":1}, {"x":8.5, "y":1}, {"x":9.5, "y":1}, {"x":10.5, "y":1}, {"x":11.5, "y":1}, {"x":12.5, "y":1}, {"x":13.5, "y":1, "w":1.5}, {"x":0, "y":2, "w":1.75}, {"x":1.75, "y":2}, {"x":2.75, "y":2}, {"x":3.75, "y":2}, {"x":4.75, "y":2}, {"x":5.75, "y":2}, {"x":6.75, "y":2}, {"x":7.75, "y":2}, {"x":8.75, "y":2}, {"x":9.75, "y":2}, {"x":10.75, "y":2}, {"x":11.75, "y":2}, {"x":12.75, "y":2}, {"x":13.75, "y":2, "w":1.25}, {"x":0, "y":3, "w":1.25}, {"x":1.25, "y":3}, {"x":2.25, "y":3}, {"x":3.25, "y":3}, {"x":4.25, "y":3}, {"x":5.25, "y":3}, {"x":6.25, "y":3}, {"x":7.25, "y":3}, {"x":8.25, "y":3}, {"x":9.25, "y":3}, {"x":10.25, "y":3}, {"x":11.25, "y":3}, {"x":12.25, "y":3, "w":1.75}, {"x":14, "y":3}, {"x":0, "y":4, "w":1.25}, {"x":1.25, "y":4, "w":1.25}, {"x":2.5, "y":4, "w":1.25}, {"x":3.75, "y":4, "w":6.25}, {"x":10, "y":4, "w":1.25}, {"x":11.25, "y":4, "w":1.25}, {"x":12.5, "y":4, "w":1.25}, {"x":13.75, "y":4, "w":1.25}]
+        }
+    }
+}

keyboards/noxary/260/keymaps/default/config.h

@@ -0,0 +1,19 @@
+/* Copyright 2019 MechMerlin
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+
+// place overrides here

keyboards/noxary/260/keymaps/default/keymap.c

@@ -0,0 +1,87 @@
+/* Copyright 2019 Rozakiin
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include QMK_KEYBOARD_H
+
+// Each layer gets a name for readability, which is then used in the keymap matrix below.
+// The underscores don't mean anything - you can have a layer called STUFF or any other name.
+// Layer names don't all need to be of the same length, obviously, and you can also skip them
+// entirely and just use numbers.
+#define _BL 0
+#define _FL1 1
+#define _FL2 2
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+    /* _BL: Base Layer(Default) - For ISO enter use ANSI enter
+    * ,-----------------------------------------------------------.
+    * |Esc | 1|  2|  3|  4|  5|  6|  7|  8|  9|  0|  -|  =| \|BSpc|
+    * |-----------------------------------------------------------|
+    * |Tab  |  Q|  W|  E|  R|  T|  Y|  U|  I|  O|  P|  [|  ]|  \  |
+    * |-----------------------------------------------------------|
+    * |CAPS   |  A|  S|  D|  F|  G|  H|  J|  K|  L|  ;|  '| #| Ent|
+    * |-----------------------------------------------------------|
+    * |Shift| \|  Z|  X|  C|  V|  B|  N|  M|  ,|  .|  /|Shift |Del|
+    * |-----------------------------------------------------------|
+    * |Ctrl|Win |Alt |        Space        |Alt |Win |Mo(1) |Ctrl |
+    * `-----------------------------------------------------------'
+    */
+    [_BL] = LAYOUT(
+        KC_ESC,  KC_1,    KC_2,    KC_3,   KC_4,    KC_5,  KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    KC_MINS, KC_EQL,   KC_BSLS, KC_BSPC,
+        KC_TAB,  KC_Q,    KC_W,    KC_E,   KC_R,    KC_T,  KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_LBRC, KC_RBRC,           KC_BSLS,
+        KC_CAPS, KC_A,    KC_S,    KC_D,   KC_F,    KC_G,  KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN, KC_QUOT, KC_NUHS,           KC_ENT,
+        KC_LSFT, KC_NUBS, KC_Z,    KC_X,   KC_C,    KC_V,  KC_B,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH, KC_RSFT,           KC_DEL, 
+        KC_LCTL, KC_LGUI, KC_LALT,                         KC_SPC,                             KC_LALT, KC_RGUI, MO(_FL1),          KC_RCTL),
+    /* _FL1: Function Layer 1 - For ISO enter use ANSI enter
+    * ,----------------------------------------------------------------.
+    * |  `|F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12|   |PScr|    |
+    * |----------------------------------------------------------------|
+    * |     |   |   |   |RST|   |   |   |   |   |   |   |   |     | Ins|
+    * |----------------------------------------------------------------|
+    * |       |   |   |   |   |   |   |   |   |   |   |   |  |    |Home|
+    * |----------------------------------------------------------------|
+    * |     |   |   |   |   |   |   |   |   |Bl-|Bl+|   |Mute|Vol+| End|
+    * |----------------------------------------------------------------|
+    * |    |    |    |      BL_Toggle       |   |   |   |    |Vol-|    |
+    * `----------------------------------------------------------------'
+    */
+    [_FL1] = LAYOUT(
+        KC_GRV,  KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,  _______, KC_PSCR,
+        _______, KC_VOLU, _______, _______, RESET,   _______, _______, _______, _______, _______, _______, _______, _______,          _______,
+        _______, KC_VOLD, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,          _______,
+        _______, _______, _______, _______, _______, _______, _______, _______, _______, BL_DEC,  BL_INC,  _______, KC_MUTE,          _______,
+        _______, _______, _______,                            BL_TOGG,                            _______, _______, _______,          _______),
+    /* _FL2: Function Layer 2 - For ISO enter use ANSI enter
+    * ,----------------------------------------------------------------.
+    * |   |  |   |   |   |   |   |   |   |   |   |   |   |    |   |    |
+    * |----------------------------------------------------------------|
+    * |     |   |   |   |   |   |   |   |   |   |   |   |   |     |    |
+    * |----------------------------------------------------------------|
+    * |       |   |   |   |   |   |   |   |   |   |   |   |  |    |    |
+    * |----------------------------------------------------------------|
+    * |     |   |   |   |   |   |   |   |   |   |   |   |    |    |    |
+    * |----------------------------------------------------------------|
+    * |    |    |    |                      |   |   |   |    |    |    |
+    * `----------------------------------------------------------------'
+    */
+    [_FL2] = LAYOUT(
+        _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,
+        _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,          _______,
+        _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,          _______,
+        _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,          _______,
+        _______, _______, _______,                            _______,                            _______, _______, _______,          _______),
+
+
+};
+

keyboards/noxary/260/keymaps/default/readme.md

@@ -0,0 +1 @@
+# The default keymap for Noxary 260

keyboards/noxary/260/readme.md

@@ -0,0 +1,15 @@
+Noxary 260
+
+![260](https://cdn.discordapp.com/attachments/438429095303315456/489188948749451276/image0.jpg)
+
+A fully customizable 60% keyboard.
+
+Keyboard Maintainer: [MechMerlin](https://github.com/mechmerlin), [Rozakiin](https://github.com/rozakiin)  
+Hardware Supported: Noxary 260 PCB   
+Hardware Availability: [Geekhack Group Buy](https://geekhack.org/index.php?topic=93572.0)  
+
+Make example for this keyboard (after setting up your build environment):
+
+    make noxary/260:default
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/noxary/260/rules.mk

@@ -0,0 +1,81 @@
+# MCU name
+#MCU = at90usb1286
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   atmega32a    bootloadHID
+BOOTLOADER = atmel-dfu
+
+
+# If you don't know the bootloader type, then you can specify the
+# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
+#   Teensy halfKay      512
+#   Teensy++ halfKay    1024
+#   Atmel DFU loader    4096
+#   LUFA bootloader     4096
+#   USBaspLoader        2048
+# OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE = lite      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = yes        # Console for debug(+400)
+COMMAND_ENABLE = yes        # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE = no            # USB Nkey Rollover
+BACKLIGHT_ENABLE = yes       # Enable keyboard backlight functionality on B7 by default
+RGBLIGHT_ENABLE = no        # Enable keyboard RGB underglow
+MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no           # Audio output on port C6
+FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
+HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)

keyboards/noxary/280/280.c

@@ -0,0 +1,70 @@
+/* Copyright 2019 %YOUR_NAME%
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include "280.h"
+
+// Optional override functions below.
+// You can leave any or all of these undefined.
+// These are only required if you want to perform custom actions.
+
+
+void matrix_init_kb(void) {
+	// put your keyboard start-up code here
+	// runs once when the firmware starts up
+  setPinOutput(D5);
+  setPinOutput(D0);
+	matrix_init_user();
+}
+
+/*
+void matrix_scan_kb(void) {
+  // put your looping keyboard code here
+  // runs every cycle (a lot)
+
+  matrix_scan_user();
+}
+
+bool process_record_kb(uint16_t keycode, keyrecord_t *record) {
+  // put your per-action keyboard code here
+  // runs for every action, just before processing by the firmware
+
+  return process_record_user(keycode, record);
+}
+
+void led_set_kb(uint8_t usb_led) {
+  // put your keyboard LED indicator (ex: Caps Lock LED) toggling code here
+
+  led_set_user(usb_led);
+}
+
+*/
+
+
+void led_set_kb(uint8_t usb_led) {
+
+    if (IS_LED_ON(usb_led, USB_LED_CAPS_LOCK)) {
+      writePinLow(D5);
+    } else {
+      writePinHigh(D5);
+    }
+
+    if (IS_LED_ON(usb_led, USB_LED_SCROLL_LOCK)) {
+      writePinLow(D0);
+    } else {
+      writePinHigh(D0);
+    }
+     
+    led_set_user(usb_led);
+}

keyboards/noxary/280/280.h

@@ -0,0 +1,49 @@
+/* Copyright 2019 MechMerlin
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#pragma once
+
+#include "quantum.h"
+
+/* This a shortcut to help you visually see your layout.
+ *
+ * The first section contains all of the arguments representing the physical
+ * layout of the board and position of the keys.
+ *
+ * The second converts the arguments into a two-dimensional array which
+ * represents the switch matrix.
+ */
+
+#define LAYOUT( \
+	K000,       K002, K103, K004, K105, K006, K107, K008, K109,       K111, K012, K113, K014, K115, K016, K117, \
+	K200, K301, K202, K303, K204, K305, K206, K307, K208, K309, K210, K311, K212, K313, K214, K315, K216, K317, \
+	K400, K501, K402, K503, K404, K505, K406, K507, K408, K509, K410, K511, K412,       K414, K515, K416, K517, \
+	K600, K701, K602, K703, K604, K705, K606, K707, K608, K709, K610, K711, K612,       K614,                   \
+	K800, K901, K802, K903, K804, K905, K806, K907, K808, K909, K810, K911, K812,       K814,       K816,       \
+    K1000,K1101,K1002,                  K1006,                  K1010,K1111,K1012,      K1014,K1115,K1016,K1117\
+) { \
+	{ K000,   K002,   K004,   K006,   K008,   KC_NO,  K012,   K014,   K016  },\
+    { KC_NO,  K103,   K105,   K107,   K109,   K111,   K113,   K115,   K117  },\
+	{ K200,   K202,   K204,   K206,   K208,   K210,   K212,   K214,   K216  },\
+    { K301,   K303,   K305,   K307,   K309,   K311,   K313,   K315,   K317  },\
+	{ K400,   K402,   K404,   K406,   K408,   K410,   K412,   K414,   K416  },\
+    { K501,   K503,   K505,   K507,   K509,   K511,   KC_NO,  K515,   K517  },\
+	{ K600,   K602,   K604,   K606,   K608,   K610,   K612,   K614,   KC_NO },\
+    { K701,   K703,   K705,   K707,   K709,   K711,   KC_NO,  KC_NO,  KC_NO },\
+	{ K800,   K802,   K804,   K806,   K808,   K810,   K812,   K814,   K816  },\
+    { K901,   K903,   K905,   K907,   K909,   K911,   KC_NO,  KC_NO,  KC_NO },\
+    { K1000,  K1002,  KC_NO,  K1006,  KC_NO,  K1010,  K1012,  K1014,  K1016 },\
+    { K1101,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  K1111,  KC_NO,  K1115,  K1117 }\
+}

keyboards/noxary/280/config.h

@@ -0,0 +1,251 @@
+/*
+Copyright 2019 MechMerlin
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0x4E58
+#define PRODUCT_ID      0x0050
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    Noxary
+#define PRODUCT         280
+#define DESCRIPTION     A custom TKL
+
+/* key matrix size */
+#define MATRIX_ROWS 12
+#define MATRIX_COLS 9
+
+/*
+ * Keyboard Matrix Assignments
+ *
+ * Change this to how you wired your keyboard
+ * COLS: AVR pins used for columns, left to right
+ * ROWS: AVR pins used for rows, top to bottom
+ * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
+ *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
+ *
+*/
+#define MATRIX_ROW_PINS { F0, E6, D6, D4, F6, F5, F4, F1, B2, D3, D2, D1}
+#define MATRIX_COL_PINS { F7, C7, C6, B6, B5, B4, D7, B0, B3}
+#define UNUSED_PINS
+
+/* COL2ROW, ROW2COL*/
+#define DIODE_DIRECTION COL2ROW
+
+/*
+ * Split Keyboard specific options, make sure you have 'SPLIT_KEYBOARD = yes' in your rules.mk, and define SOFT_SERIAL_PIN.
+ */
+#define SOFT_SERIAL_PIN D0 // or D1, D2, D3, E6
+
+#define BACKLIGHT_PIN B7
+#define BACKLIGHT_BREATHING
+#define BACKLIGHT_LEVELS 3
+
+// #define RGB_DI_PIN E2
+// #ifdef RGB_DI_PIN
+//   #define RGBLED_NUM 16
+//   #define RGBLIGHT_HUE_STEP 8
+//   #define RGBLIGHT_SAT_STEP 8
+//   #define RGBLIGHT_VAL_STEP 8
+//   #define RGBLIGHT_LIMIT_VAL 255 /* The maximum brightness level */
+//   #define RGBLIGHT_SLEEP  /* If defined, the RGB lighting will be switched off when the host goes to sleep */
+// /*== all animations enable ==*/
+//   #define RGBLIGHT_ANIMATIONS
+// /*== or choose animations ==*/
+//   #define RGBLIGHT_EFFECT_BREATHING
+//   #define RGBLIGHT_EFFECT_RAINBOW_MOOD
+//   #define RGBLIGHT_EFFECT_RAINBOW_SWIRL
+//   #define RGBLIGHT_EFFECT_SNAKE
+//   #define RGBLIGHT_EFFECT_KNIGHT
+//   #define RGBLIGHT_EFFECT_CHRISTMAS
+//   #define RGBLIGHT_EFFECT_STATIC_GRADIENT
+//   #define RGBLIGHT_EFFECT_RGB_TEST
+//   #define RGBLIGHT_EFFECT_ALTERNATING
+// /*== customize breathing effect ==*/
+//   /*==== (DEFAULT) use fixed table instead of exp() and sin() ====*/
+//   #define RGBLIGHT_BREATHE_TABLE_SIZE 256      // 256(default) or 128 or 64
+//   /*==== use exp() and sin() ====*/
+//   #define RGBLIGHT_EFFECT_BREATHE_CENTER 1.85  // 1 to 2.7
+//   #define RGBLIGHT_EFFECT_BREATHE_MAX    255   // 0 to 255
+// #endif
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCING_DELAY 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/* If defined, GRAVE_ESC will always act as ESC when CTRL is held.
+ * This is userful for the Windows task manager shortcut (ctrl+shift+esc).
+ */
+// #define GRAVE_ESC_CTRL_OVERRIDE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/* key combination for magic key command */
+/* defined by default; to change, uncomment and set to the combination you want */
+// #define IS_COMMAND() (get_mods() == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)))
+
+/* control how magic key switches layers */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
+
+/* override magic key keymap */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
+//#define MAGIC_KEY_HELP           H
+//#define MAGIC_KEY_HELP_ALT       SLASH
+//#define MAGIC_KEY_DEBUG          D
+//#define MAGIC_KEY_DEBUG_MATRIX   X
+//#define MAGIC_KEY_DEBUG_KBD      K
+//#define MAGIC_KEY_DEBUG_MOUSE    M
+//#define MAGIC_KEY_VERSION        V
+//#define MAGIC_KEY_STATUS         S
+//#define MAGIC_KEY_CONSOLE        C
+//#define MAGIC_KEY_LAYER0         0
+//#define MAGIC_KEY_LAYER0_ALT     GRAVE
+//#define MAGIC_KEY_LAYER1         1
+//#define MAGIC_KEY_LAYER2         2
+//#define MAGIC_KEY_LAYER3         3
+//#define MAGIC_KEY_LAYER4         4
+//#define MAGIC_KEY_LAYER5         5
+//#define MAGIC_KEY_LAYER6         6
+//#define MAGIC_KEY_LAYER7         7
+//#define MAGIC_KEY_LAYER8         8
+//#define MAGIC_KEY_LAYER9         9
+//#define MAGIC_KEY_BOOTLOADER     B
+//#define MAGIC_KEY_BOOTLOADER_ALT ESC
+//#define MAGIC_KEY_LOCK           CAPS
+//#define MAGIC_KEY_EEPROM         E
+//#define MAGIC_KEY_EEPROM_CLEAR   BSPACE
+//#define MAGIC_KEY_NKRO           N
+//#define MAGIC_KEY_SLEEP_LED      Z
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+/*
+ * MIDI options
+ */
+
+/* Prevent use of disabled MIDI features in the keymap */
+//#define MIDI_ENABLE_STRICT 1
+
+/* enable basic MIDI features:
+   - MIDI notes can be sent when in Music mode is on
+*/
+//#define MIDI_BASIC
+
+/* enable advanced MIDI features:
+   - MIDI notes can be added to the keymap
+   - Octave shift and transpose
+   - Virtual sustain, portamento, and modulation wheel
+   - etc.
+*/
+//#define MIDI_ADVANCED
+
+/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
+//#define MIDI_TONE_KEYCODE_OCTAVES 1
+
+/*
+ * HD44780 LCD Display Configuration
+ */
+/*
+#define LCD_LINES           2     //< number of visible lines of the display
+#define LCD_DISP_LENGTH    16     //< visibles characters per line of the display
+
+#define LCD_IO_MODE      1            //< 0: memory mapped mode, 1: IO port mode
+
+#if LCD_IO_MODE
+#define LCD_PORT         PORTB        //< port for the LCD lines
+#define LCD_DATA0_PORT   LCD_PORT     //< port for 4bit data bit 0
+#define LCD_DATA1_PORT   LCD_PORT     //< port for 4bit data bit 1
+#define LCD_DATA2_PORT   LCD_PORT     //< port for 4bit data bit 2
+#define LCD_DATA3_PORT   LCD_PORT     //< port for 4bit data bit 3
+#define LCD_DATA0_PIN    4            //< pin for 4bit data bit 0
+#define LCD_DATA1_PIN    5            //< pin for 4bit data bit 1
+#define LCD_DATA2_PIN    6            //< pin for 4bit data bit 2
+#define LCD_DATA3_PIN    7            //< pin for 4bit data bit 3
+#define LCD_RS_PORT      LCD_PORT     //< port for RS line
+#define LCD_RS_PIN       3            //< pin  for RS line
+#define LCD_RW_PORT      LCD_PORT     //< port for RW line
+#define LCD_RW_PIN       2            //< pin  for RW line
+#define LCD_E_PORT       LCD_PORT     //< port for Enable line
+#define LCD_E_PIN        1            //< pin  for Enable line
+#endif
+*/
+
+/* Bootmagic Lite key configuration */
+// #define BOOTMAGIC_LITE_ROW 0
+// #define BOOTMAGIC_LITE_COLUMN 0