Adds a configurable initial delay to the audio clicky feature (#4286)

* Adding an AUDIO_CLICKY_DELAY_DURATION configurable value to the AUDIO_CLICKY feature.

* Tweaking my community keymap to work better with my rev 4 planck.

Vagrantfile

@@ -7,6 +7,8 @@ Vagrant.configure(2) do |config|
 
   # VMware/Virtualbox ( and also Hyperv/Parallels) 64 bit
   config.vm.box = "generic/debian9"
+  
+  config.vm.synced_folder '.', '/vagrant'
 
   # This section allows you to customize the Virtualbox VM
   # settings, ie showing the GUI or upping the memory
@@ -64,7 +66,7 @@ Vagrant.configure(2) do |config|
   # If this causes issues you can run a 'vagrant destroy' and then
   # add a # before ,run: (or change "always" to "once") and run 'vagrant up' to get a working
   # non-updated box and then attempt to troubleshoot or open a Github issue
-  config.vm.provision "shell", inline: "/bin/sh -c 'yes | /vagrant/util/qmk_install.sh'", run: "always"
+  config.vm.provision "shell", inline: "/vagrant/util/qmk_install.sh", run: "always"
 
   config.vm.post_up_message = <<-EOT
 

docs/config_options.md

@@ -171,6 +171,8 @@ If you define these options you will enable the associated feature, which may in
   * how long for the Combo keys to be detected. Defaults to `TAPPING_TERM` if not defined.
 * `#define TAP_CODE_DELAY 100`
   * Sets the delay between `register_code` and `unregister_code`, if you're having issues with it registering properly (common on VUSB boards). The value is in milliseconds.
+* `#define TAP_HOLD_CAPS_DELAY 200`
+  * Sets the delay for Tap Hold keys (`LT`, `MT`) when using `KC_CAPSLOCK` keycode, as this has some special handling on MacOS.  The value is in milliseconds, and defaults to 200ms if not defined. 
 
 ## RGB Light Configuration
 

docs/feature_audio.md

@@ -175,8 +175,9 @@ You can configure the default, min and max frequencies, the stepping and built i
 | `AUDIO_CLICKY_FREQ_DEFAULT` | 440.0f | Sets the default/starting audio frequency for the clicky sounds. |
 | `AUDIO_CLICKY_FREQ_MIN` | 65.0f | Sets the lowest frequency (under 60f are a bit buggy). |
 | `AUDIO_CLICKY_FREQ_MAX` | 1500.0f | Sets the the highest frequency. Too high may result in coworkers attacking you. |
-| `AUDIO_CLICKY_FREQ_FACTOR` | 1.18921f| Sets the stepping of UP/DOWN key codes. |
+| `AUDIO_CLICKY_FREQ_FACTOR` | 1.18921f| Sets the stepping of UP/DOWN key codes.  This is a multiplicative factor.  The default steps the frequency up/down by a musical minor third.  |
 | `AUDIO_CLICKY_FREQ_RANDOMNESS`     |  0.05f |  Sets a factor of randomness for the clicks, Setting this to `0f` will make each click identical, and `1.0f` will make this sound much like the 90's computer screen scrolling/typing effect. | 
+| `AUDIO_CLICKY_DELAY_DURATION` | 1 | An integer note duration where 1 is 1/16th of the tempo, or a sixty-fourth note (see `quantum/audio/musical_notes.h` for implementation details). The main clicky effect will be delayed by this duration.  Adjusting this to values around 6-12 will help compensate for loud switches. |
 
 
 

docs/feature_rgb_matrix.md

@@ -197,6 +197,8 @@ enum rgb_matrix_effects {
     RGB_MATRIX_CYCLE_ALL,           // Full keyboard solid hue cycling through full gradient
     RGB_MATRIX_CYCLE_LEFT_RIGHT,    // Full gradient scrolling left to right
     RGB_MATRIX_CYCLE_UP_DOWN,       // Full gradient scrolling top to bottom
+    RGB_MATRIX_CYCLE_OUT_IN,        // Full gradient scrolling out to in
+    RGB_MATRIX_CYCLE_OUT_IN_DUAL,   // Full dual gradients scrolling out to in
     RGB_MATRIX_RAINBOW_MOVING_CHEVRON,  // Full gradent Chevron shapped scrolling left to right
     RGB_MATRIX_DUAL_BEACON,         // Full gradient spinning around center of keyboard
     RGB_MATRIX_RAINBOW_BEACON,      // Full tighter gradient spinning around center of keyboard
@@ -236,6 +238,8 @@ You can disable a single effect by defining `DISABLE_[EFFECT_NAME]` in your `con
 |`#define DISABLE_RGB_MATRIX_CYCLE_ALL`                 |Disables `RGB_MATRIX_CYCLE_ALL`                |
 |`#define DISABLE_RGB_MATRIX_CYCLE_LEFT_RIGHT`          |Disables `RGB_MATRIX_CYCLE_LEFT_RIGHT`         |
 |`#define DISABLE_RGB_MATRIX_CYCLE_UP_DOWN`             |Disables `RGB_MATRIX_CYCLE_UP_DOWN`            |
+|`#define DISABLE_RGB_MATRIX_CYCLE_OUT_IN`              |Disables `RGB_MATRIX_CYCLE_OUT_IN`             |
+|`#define DISABLE_RGB_MATRIX_CYCLE_OUT_IN_DUAL`         |Disables `RGB_MATRIX_CYCLE_OUT_IN_DUAL`        |
 |`#define DISABLE_RGB_MATRIX_RAINBOW_MOVING_CHEVRON`    |Disables `RGB_MATRIX_RAINBOW_MOVING_CHEVRON`   |
 |`#define DISABLE_RGB_MATRIX_DUAL_BEACON`               |Disables `RGB_MATRIX_DUAL_BEACON`              |
 |`#define DISABLE_RGB_MATRIX_RAINBOW_BEACON`            |Disables `RGB_MATRIX_RAINBOW_BEACON`           |

docs/feature_rgblight.md

@@ -129,7 +129,7 @@ The following options are used to tweak the various animations:
 |`RGBLIGHT_EFFECT_KNIGHT_LED_NUM`    |`RGBLED_NUM` |The number of LEDs to have the "Knight" animation travel                             |
 |`RGBLIGHT_EFFECT_KNIGHT_LENGTH`     |`3`          |The number of LEDs to light up for the "Knight" animation                            |
 |`RGBLIGHT_EFFECT_KNIGHT_OFFSET`     |`0`          |The number of LEDs to start the "Knight" animation from the start of the strip by    |
-|`RGBLIGHT_RAINBOW_SWIRL_RANGE`      |`360`        |Range adjustment for the rainbow swirl effect to get different swirls                |
+|`RGBLIGHT_RAINBOW_SWIRL_RANGE`      |`255`        |Range adjustment for the rainbow swirl effect to get different swirls                |
 |`RGBLIGHT_EFFECT_SNAKE_LENGTH`      |`4`          |The number of LEDs to light up for the "Snake" animation                             |
 
 ### Example Usage to Reduce Memory Footprint
@@ -176,44 +176,100 @@ const uint8_t RGBLED_GRADIENT_RANGES[] PROGMEM = {255, 170, 127, 85, 64};
 
 If you need to change your RGB lighting in code, for example in a macro to change the color whenever you switch layers, QMK provides a set of functions to assist you. See [`rgblight.h`](https://github.com/qmk/qmk_firmware/blob/master/quantum/rgblight.h) for the full list, but the most commonly used functions include:
 
-|Function                                    |Description                                                                                                                                                   |
-|--------------------------------------------|--------------------------------------------------------------------------------------------------------------------------------------------------------------|
-|`rgblight_enable()`                         |Turn LEDs on, based on their previous state                                                                                                                   |
-|`rgblight_enable_noeeprom()`                |Turn LEDs on, based on their previous state (not written to EEPROM)                                                                                           |
-|`rgblight_disable()`                        |Turn LEDs off                                                                                                                                                 |
-|`rgblight_disable_noeeprom()`               |Turn LEDs off (not written to EEPROM)                                                                                                                         |
-|`rgblight_mode(x)`                          |Set the mode, if RGB animations are enabled                                                                                                                   |
-|`rgblight_mode_noeeprom(x)`                 |Set the mode, if RGB animations are enabled (not written to EEPROM)                                                                                           |
-|`rgblight_setrgb(r, g, b)`                  |Set all LEDs to the given RGB value where `r`/`g`/`b` are between 0 and 255 (not written to EEPROM)                                                           |
-|`rgblight_setrgb_at(r, g, b, led)`          |Set a single LED to the given RGB value, where `r`/`g`/`b` are between 0 and 255 and `led` is between 0 and `RGBLED_NUM` (not written to EEPROM)              |
+### Utility Functions
+|Function                                    |Description                                                        |
+|--------------------------------------------|-------------------------------------------------------------------|
+|`sethsv(hue, sat, val, ledbuf)`             |Set ledbuf to the given HSV value                                  |
+|`sethsv_raw(hue, sat, val, ledbuf)`         |Set ledbuf to the given HSV value without RGBLIGHT_LIMIT_VAL check |
+|`setrgb(r, g, b, ledbuf)`                   |Set ledbuf to the given RGB value where `r`/`g`/`b`                |
+
+### Low level Functions
+|Function                                    |Description                                |
+|--------------------------------------------|-------------------------------------------|
+|`rgblight_set()`                            |Flash out led buffers to LEDs              |
+|`rgblight_set_clipping_range(pos, num)`     |Set clipping Range. see [Clipping Range](#clipping-range) |
+
+Example:
+```c
+sethsv(HSV_WHITE, (LED_TYPE *)&led[0]); // led 0
+sethsv(HSV_RED,   (LED_TYPE *)&led[1]); // led 1
+sethsv(HSV_GREEN, (LED_TYPE *)&led[2]); // led 2
+rgblight_set(); // Utility functions do not call rgblight_set() automatically, so they need to be called explicitly.
+```
+
+### Effects and Animations Functions
+#### effect range setting
+|Function                                    |Description       |
+|--------------------------------------------|------------------|
+|`rgblight_set_effect_range(pos, num)`       |Set Effects Range |
+
+#### direct operation
+|Function                                    |Description  |
+|--------------------------------------------|-------------|
+|`rgblight_setrgb_at(r, g, b, index)`          |Set a single LED to the given RGB value, where `r`/`g`/`b` are between 0 and 255 and `index` is between 0 and `RGBLED_NUM` (not written to EEPROM) |
+|`rgblight_sethsv_at(h, s, v, index)`          |Set a single LED to the given HSV value, where `h`/`s`/`v` are between 0 and 255, and `index` is between 0 and `RGBLED_NUM` (not written to EEPROM) |
 |`rgblight_setrgb_range(r, g, b, start, end)`|Set a continuous range of LEDs to the given RGB value, where `r`/`g`/`b` are between 0 and 255 and `start`(included) and `stop`(excluded) are between 0 and `RGBLED_NUM` (not written to EEPROM)|
-|`rgblight_setrgb_master(r, g, b)`           |Set the LEDs on the master side  to the given RGB value, where `r`/`g`/`b` are between 0 and 255 (not written to EEPROM)                                      |
-|`rgblight_setrgb_slave(r, g, b)`            |Set the LEDs on the slave side  to the given RGB value, where `r`/`g`/`b` are between 0 and 255 (not written to EEPROM)                                       |
-|`rgblight_sethsv(h, s, v)`                  |Set all LEDs to the given HSV value where `h` is between 0 and 360 and `s`/`v` are between 0 and 255                                                          |
-|`rgblight_sethsv_noeeprom(h, s, v)`         |Set all LEDs to the given HSV value where `h` is between 0 and 360 and `s`/`v` are between 0 and 255 (not written to EEPROM)                                  |
-|`rgblight_sethsv_at(h, s, v, led)`          |Set a single LED to the given HSV value, where `h` is between 0 and 360, `s`/`v` are between 0 and 255, and `led` is between 0 and `RGBLED_NUM` (not written to EEPROM)|
-|`rgblight_sethsv_range(h, s, v, start, end)`|Set a continuous range of LEDs to the given HSV value, where `h` is between 0 and 360, `s`/`v` are between 0 and 255, and `start`(included) and `stop`(excluded) are between 0 and `RGBLED_NUM` (not written to EEPROM)|
-|`rgblight_sethsv_master(h, s, v)`           |Set the LEDs on the master side to the given HSV value, where `h` is between 0 and 360, `s`/`v` are between 0 and 255 (not written to EEPROM)                 |
-|`rgblight_sethsv_slave(h, s, v)`            |Set the LEDs on the slave side to the given HSV value, where `h` is between 0 and 360, `s`/`v` are between 0 and 255 (not written to EEPROM)                  |
-|`rgblight_toggle()`                         |Toggle all LEDs between on and off                                                                                                                            |
-|`rgblight_toggle_noeeprom()`                |Toggle all LEDs between on and off (not written to EEPROM)                                                                                                    |
-|`rgblight_step()`                           |Change the mode to the next RGB animation in the list of enabled RGB animations                                                                               |
-|`rgblight_step_noeeprom()`                  |Change the mode to the next RGB animation in the list of enabled RGB animations (not written to EEPROM)                                                       |
-|`rgblight_step_reverse()`                   |Change the mode to the previous RGB animation in the list of enabled RGB animations                                                                           |
-|`rgblight_step_reverse_noeeprom()`          |Change the mode to the previous RGB animation in the list of enabled RGB animations (not written to EEPROM)                                                   |
-|`rgblight_increase_hue()`                   |Increase the hue for all LEDs. This wraps around at maximum hue                                                                                               |
-|`rgblight_increase_hue_noeeprom()`          |Increase the hue for all LEDs. This wraps around at maximum hue (not written to EEPROM)                                                                       |
-|`rgblight_decrease_hue()`                   |Decrease the hue for all LEDs. This wraps around at minimum hue                                                                                               |
-|`rgblight_decrease_hue_noeeprom()`          |Decrease the hue for all LEDs. This wraps around at minimum hue (not written to EEPROM)                                                                       |
-|`rgblight_increase_sat()`                   |Increase the saturation for all LEDs. This wraps around at maximum saturation                                                                                 |
-|`rgblight_increase_sat_noeeprom()`          |Increase the saturation for all LEDs. This wraps around at maximum saturation (not written to EEPROM)                                                         |
-|`rgblight_decrease_sat()`                   |Decrease the saturation for all LEDs. This wraps around at minimum saturation                                                                                 |
-|`rgblight_decrease_sat_noeeprom()`          |Decrease the saturation for all LEDs. This wraps around at minimum saturation (not written to EEPROM)                                                         |
-|`rgblight_increase_val()`                   |Increase the value for all LEDs. This wraps around at maximum value                                                                                           |
-|`rgblight_increase_val_noeeprom()`          |Increase the value for all LEDs. This wraps around at maximum value (not written to EEPROM)                                                                   |
-|`rgblight_decrease_val()`                   |Decrease the value for all LEDs. This wraps around at minimum value                                                                                           |
-|`rgblight_decrease_val_noeeprom()`          |Decrease the value for all LEDs. This wraps around at minimum value (not written to EEPROM)                                                                   |
-|`rgblight_set_clipping_range(pos, num)`     |Set clipping Range                                                                                                                                            |
+|`rgblight_sethsv_range(h, s, v, start, end)`|Set a continuous range of LEDs to the given HSV value, where `h`/`s`/`v` are between 0 and 255, and `start`(included) and `stop`(excluded) are between 0 and `RGBLED_NUM` (not written to EEPROM)|
+|`rgblight_setrgb(r, g, b)`                  |Set effect range LEDs to the given RGB value where `r`/`g`/`b` are between 0 and 255 (not written to EEPROM) |
+|`rgblight_setrgb_master(r, g, b)`           |Set the LEDs on the master side  to the given RGB value, where `r`/`g`/`b` are between 0 and 255 (not written to EEPROM) |
+|`rgblight_setrgb_slave(r, g, b)`            |Set the LEDs on the slave side  to the given RGB value, where `r`/`g`/`b` are between 0 and 255 (not written to EEPROM) |
+|`rgblight_sethsv_master(h, s, v)`           |Set the LEDs on the master side to the given HSV value, where `h`/`s`/`v` are between 0 and 255 (not written to EEPROM) |
+|`rgblight_sethsv_slave(h, s, v)`            |Set the LEDs on the slave side to the given HSV value, where `h`/`s`/`v` are between 0 and 255 (not written to EEPROM) |
+
+Example:
+```c
+rgblight_sethsv(HSV_WHITE, 0); // led 0
+rgblight_sethsv(HSV_RED,   1); // led 1
+rgblight_sethsv(HSV_GREEN, 2); // led 2
+// The above functions automatically calls rgblight_set(), so there is no need to call it explicitly.
+// Note that it is inefficient to call repeatedly.
+```
+
+#### effect mode change
+|Function                                    |Description  |
+|--------------------------------------------|-------------|
+|`rgblight_mode(x)`                          |Set the mode, if RGB animations are enabled |
+|`rgblight_mode_noeeprom(x)`                 |Set the mode, if RGB animations are enabled (not written to EEPROM) |
+|`rgblight_step()`                           |Change the mode to the next RGB animation in the list of enabled RGB animations |
+|`rgblight_step_noeeprom()`                  |Change the mode to the next RGB animation in the list of enabled RGB animations (not written to EEPROM) |
+|`rgblight_step_reverse()`                   |Change the mode to the previous RGB animation in the list of enabled RGB animations |
+|`rgblight_step_reverse_noeeprom()`          |Change the mode to the previous RGB animation in the list of enabled RGB animations (not written to EEPROM) |
+
+#### effects mode disable/enable
+|Function                                    |Description  |
+|--------------------------------------------|-------------|
+|`rgblight_toggle()`                         |Toggle effect range LEDs between on and off |
+|`rgblight_toggle_noeeprom()`                |Toggle effect range LEDs between on and off (not written to EEPROM) |
+|`rgblight_enable()`                         |Turn effect range LEDs on, based on their previous state |
+|`rgblight_enable_noeeprom()`                |Turn effect range LEDs on, based on their previous state (not written to EEPROM) |
+|`rgblight_disable()`                        |Turn effect range LEDs off |
+|`rgblight_disable_noeeprom()`               |Turn effect range LEDs off (not written to EEPROM) |
+
+#### hue, sat, val change
+|Function                                    |Description  |
+|--------------------------------------------|-------------|
+|`rgblight_increase_hue()`                   |Increase the hue for effect range LEDs. This wraps around at maximum hue |
+|`rgblight_increase_hue_noeeprom()`          |Increase the hue for effect range LEDs. This wraps around at maximum hue (not written to EEPROM) |
+|`rgblight_decrease_hue()`                   |Decrease the hue for effect range LEDs. This wraps around at minimum hue |
+|`rgblight_decrease_hue_noeeprom()`          |Decrease the hue for effect range LEDs. This wraps around at minimum hue (not written to EEPROM) |
+|`rgblight_increase_sat()`                   |Increase the saturation for effect range LEDs. This wraps around at maximum saturation |
+|`rgblight_increase_sat_noeeprom()`          |Increase the saturation for effect range LEDs. This wraps around at maximum saturation (not written to EEPROM) |
+|`rgblight_decrease_sat()`                   |Decrease the saturation for effect range LEDs. This wraps around at minimum saturation |
+|`rgblight_decrease_sat_noeeprom()`          |Decrease the saturation for effect range LEDs. This wraps around at minimum saturation (not written to EEPROM) |
+|`rgblight_increase_val()`                   |Increase the value for effect range LEDs. This wraps around at maximum value |
+|`rgblight_increase_val_noeeprom()`          |Increase the value for effect range LEDs. This wraps around at maximum value (not written to EEPROM) |
+|`rgblight_decrease_val()`                   |Decrease the value for effect range LEDs. This wraps around at minimum value |
+|`rgblight_decrease_val_noeeprom()`          |Decrease the value for effect range LEDs. This wraps around at minimum value (not written to EEPROM) |
+|`rgblight_sethsv(h, s, v)`                  |Set effect range LEDs to the given HSV value where `h`/`s`/`v` are between 0 and 255 |
+|`rgblight_sethsv_noeeprom(h, s, v)`         |Set effect range LEDs to the given HSV value where `h`/`s`/`v` are between 0 and 255 (not written to EEPROM) |
+
+#### query
+|Function               |Description      |
+|-----------------------|-----------------|
+|`rgblight_get_mode()`  |Get current mode |
+|`rgblight_get_hue()`   |Get current hue  |
+|`rgblight_get_sat()`   |Get current sat  |
+|`rgblight_get_val()`   |Get current val  |
 
 ## Colors
 
@@ -324,4 +380,6 @@ In addition to setting the Clipping Range, you can use `RGBLIGHT_LED_MAP` togeth
 ```
 <img src="https://user-images.githubusercontent.com/2170248/55743747-119e4c00-5a6e-11e9-91e5-013203ffae8a.JPG" alt="clip mapped" width="70%"/>
 
+## Hardware Modification
+
 If your keyboard lacks onboard underglow LEDs, you may often be able to solder on an RGB LED strip yourself. You will need to find an unused pin to wire to the data pin of your LED strip. Some keyboards may break out unused pins from the MCU to make soldering easier. The other two pins, VCC and GND, must also be connected to the appropriate power pins.

docs/feature_space_cadet.md

@@ -20,7 +20,7 @@ Firstly, in your keymap, do one of the following:
 |`KC_RCPC`  |Right Control when held, `)` when tapped   |
 |`KC_LAPO`  |Left Alt when held, `(` when tapped        |
 |`KC_RAPC`  |Right Alt when held, `)` when tapped       |
-|`KC_SFTENT`|Right Shift when held, `Enter` when tapped |
+|`KC_SFTENT`|Right Shift when held, Enter when tapped   |
 
 ## Caveats
 
@@ -38,10 +38,10 @@ By default Space Cadet assumes a US ANSI layout, but if your layout uses differe
 |----------------|-------------------------------|---------------------------------------------------------------------------------|
 |`LSPO_KEYS`     |`KC_LSFT, LSPO_MOD, LSPO_KEY`  |Send `KC_LSFT` when held, the mod and  key defined by `LSPO_MOD` and `LSPO_KEY`. |
 |`RSPC_KEYS`     |`KC_RSFT, RSPC_MOD, RSPC_KEY`  |Send `KC_RSFT` when held, the mod and  key defined by `RSPC_MOD` and `RSPC_KEY`. |
-|`LCPO_KEYS`     |`KC_LCTL, KC_LCTL, KC_9`       |Send `KC_LCTL` when held, the mod `KC_LCTL` with the key `KC_9` when tapped.     |
-|`RCPC_KEYS`     |`KC_RCTL, KC_RCTL, KC_0`       |Send `KC_RCTL` when held, the mod `KC_RCTL` with the key `KC_0` when tapped.     |
-|`LAPO_KEYS`     |`KC_LALT, KC_LALT, KC_9`       |Send `KC_LALT` when held, the mod `KC_LALT` with the key `KC_9` when tapped.     |
-|`RAPC_KEYS`     |`KC_RALT, KC_RALT, KC_0`       |Send `KC_RALT` when held, the mod `KC_RALT` with the key `KC_0` when tapped.     |
+|`LCPO_KEYS`     |`KC_LCTL, KC_LSFT, KC_9`       |Send `KC_LCTL` when held, the mod `KC_LSFT` with the key `KC_9` when tapped.     |
+|`RCPC_KEYS`     |`KC_RCTL, KC_RSFT, KC_0`       |Send `KC_RCTL` when held, the mod `KC_RSFT` with the key `KC_0` when tapped.     |
+|`LAPO_KEYS`     |`KC_LALT, KC_LSFT, KC_9`       |Send `KC_LALT` when held, the mod `KC_LSFT` with the key `KC_9` when tapped.     |
+|`RAPC_KEYS`     |`KC_RALT, KC_RSFT, KC_0`       |Send `KC_RALT` when held, the mod `KC_RSFT` with the key `KC_0` when tapped.     |
 |`SFTENT_KEYS`   |`KC_RSFT, KC_TRNS, SFTENT_KEY` |Send `KC_RSFT` when held, no mod with the key `SFTENT_KEY` when tapped.          |
 
 

docs/feature_userspace.md

@@ -110,7 +110,7 @@ QMK has a bunch of [functions](custom_quantum_functions.md) that have [`_quantum
 However, you can actually add support for keymap version, so that you can use it in both your userspace and your keymap! 
 
 
-For instance, lets looks at the `layer_state_set_user` function.  Lets enable the [Tri Layer State](ref_functions.md#olkb-tri-layers) functionalitly to all of our boards, and then still have your `keymap.c` still able to use this functionality. 
+For instance, let's look at the `layer_state_set_user()` function.  You can enable the [Tri Layer State](ref_functions.md#olkb-tri-layers) functionality on all of your boards, while also retaining the Tri Layer functionality in your `keymap.c` files. 
 
 In your `<name.c>` file, you'd want to add this: 
 ```c

docs/keycodes.md

@@ -216,6 +216,11 @@ This is a reference only. Each group of keys links to the page documenting their
 |`KC_GESC`      |`GRAVE_ESC`|Escape when tapped, <code>&#96;</code> when pressed with Shift or GUI|
 |`KC_LSPO`      |           |Left Shift when held, `(` when tapped                                |
 |`KC_RSPC`      |           |Right Shift when held, `)` when tapped                               |
+|`KC_LCPO`      |           |Left Control when held, `(` when tapped                              |
+|`KC_RCPC`      |           |Right Control when held, `)` when tapped                             |
+|`KC_LAPO`      |           |Left Alt when held, `(` when tapped                                  |
+|`KC_RAPC`      |           |Right Alt when held, `)` when tapped                                 |
+|`KC_SFTENT`    |           |Right Shift when held, Enter when tapped                             |
 |`KC_LEAD`      |           |The [Leader key](feature_leader_key.md)                              |
 |`KC_LOCK`      |           |The [Lock key](feature_key_lock.md)                                  |
 |`FUNC(n)`      |`F(n)`     |Call `fn_action(n)` (deprecated)                                     |

docs/quantum_keycodes.md

@@ -1,6 +1,6 @@
 # Quantum Keycodes
 
-Quantum keycodes allow for easier customisation of your keymap than the basic ones provide, without having to define custom actions.
+Quantum keycodes allow for easier customization of your keymap than the basic ones provide, without having to define custom actions.
 
 All keycodes within quantum are numbers between `0x0000` and `0xFFFF`. Within your `keymap.c` it may look like you have functions and other special cases, but ultimately the C preprocessor will translate those into a single 4 byte integer. QMK has reserved `0x0000` through `0x00FF` for standard keycodes. These are keycodes such as `KC_A`, `KC_1`, and `KC_LCTL`, which are basic keys defined in the USB HID specification.
 
@@ -16,6 +16,11 @@ On this page we have documented keycodes between `0x00FF` and `0xFFFF` which are
 |`KC_GESC`      |`GRAVE_ESC`|Escape when tapped, <code>&#96;</code> when pressed with Shift or GUI|
 |`KC_LSPO`      |           |Left Shift when held, `(` when tapped                                |
 |`KC_RSPC`      |           |Right Shift when held, `)` when tapped                               |
+|`KC_LCPO`      |           |Left Control when held, `(` when tapped                              |
+|`KC_RCPC`      |           |Right Control when held, `)` when tapped                             |
+|`KC_LAPO`      |           |Left Alt when held, `(` when tapped                                  |
+|`KC_RAPC`      |           |Right Alt when held, `)` when tapped                                 |
+|`KC_SFTENT`    |           |Right Shift when held, Enter when tapped                             |
 |`KC_LEAD`      |           |The [Leader key](feature_leader_key.md)                              |
 |`KC_LOCK`      |           |The [Lock key](feature_key_lock.md)                                  |
 |`FUNC(n)`      |`F(n)`     |Call `fn_action(n)` (deprecated)                                     |

docs/zh-cn/contributing.md

@@ -0,0 +1,205 @@
+# 如何做贡献
+
+👍🎉 首先感谢各位百忙之中抽空阅读本文档，并为我们无私奉献。给您点赞啦！ 🎉👍
+
+第三方的帮助让Q酱成长了许多呢，Q酱也从你们那学到了不少新东西。Q酱希望每一个想帮助我的人都能很方便的做出有用的贡献。在这里我给摩拳擦掌的你们写了一点引导，让你们的代码在不对我做重大改动的情况下都能成功的被采纳哦。
+
+* [项目概况](#项目概况)
+* [代码规范](#代码规范)
+* [一般教程](#一般教程)
+* [行为守则对于我来说有何意义?](#行为守则对于我来说有何意义?)
+
+## 这文章巨长无比不想读啊! 我就想问个问题而已!
+
+您要是想问关于Q酱的问题的话可以在[OLKB Subreddit](https://reddit.com/r/olkb)或者是[Discord](https://discord.gg/Uq7gcHh)随意问。
+
+请记住:
+
+* 维护Q酱的小可爱有的时候可能会有点忙，不能及时回答您的问题，耐心等等，他们都是很nice的人呀。
+* 维护Q酱的人都是很无私的善良的人。无论是贡献代码还是回答问题，都是义务的。有时见到他们努力回答各种问题，解决各种BUG，Q酱也是很心疼的。
+* 您可以看看下面的教程，可以让您的问题浅显易懂，更容易回答：
+  * https://opensource.com/life/16/10/how-ask-technical-questions
+  * http://www.catb.org/esr/faqs/smart-questions.html
+
+# 项目概况
+
+Q酱很大一部分是用C语言组成的，不过有一小部分特性是C++的。怎么说呢，都是我的一部分，两个我都爱。Q酱一般是在键盘上的嵌入式处理器那里工作的，尤其与AVR([LUFA](http://www.fourwalledcubicle.com/LUFA.php))和ARM ([ChibiOS](http://www.chibios.com))两小哥哥搭配，干活不累，嘻嘻。如果您精通Arduino的话您会发现很多熟悉的概念，但也有点不爽，因为您以前的经验可能没法用来帮助Q酱。
+
+<!-- 需要修正: 这里放些学习C语言的资源。另外感谢修正的小可爱。谢谢您了。-->
+
+# Q酱，我在哪能帮助你嘞?
+
+您要是有问题的话可以 [提出一个issue](https://github.com/qmk/qmk_firmware/issues) 或 [在Discord上交流一下](https://discord.gg/Uq7gcHh).
+
+# Q酱，我如何帮助你?
+
+您以前是否没为开源贡献过代码，而又想知道帮助Q酱是怎么一回事? 稍安勿躁，咱给您总结一下！
+
+0. 先注册一个 [GitHub](https://github.com) 账户。
+1. 做好一个你要贡献的布局，那就要 [找一个你想解决的问题](https://github.com/qmk/qmk_firmware/issues)，或者 [找一个你想添加的特性](https://github.com/qmk/qmk_firmware/issues?q=is%3Aopen+is%3Aissue+label%3Afeature)。
+2. 把关联着问题的仓库分叉（fork）到你的仓库。这样你在`你的GitHub用户名/qmk_firmware`就有一个仓库备份啦。
+3. 使用 `git clone https://github.com/此处添GitHub用户名/此处添仓库名.git`这个命令把仓库同步到你的电脑中。
+4. 您要是想开发一个新特性的话可以先创建一个issue和Q酱的维护者讨论一下您要做什么。
+5. 使用`git checkout -b 此处写分支名字（别用汉字）`命令来创建一个分支（branch）用于开发。
+6. 对要解决的问题或要添加的特性进行适当的更改。
+7. 使用 `git add 把改变的文件的目录写这里` 可以添加改变的文件内容到git用于管理工程状态的索引（快照）里。
+8. 使用 `git commit -m "这里写修改的相关信息"` 来描述你做出了什么修改。
+9. 使用 `git push origin 此处写分支名字`来把你的更改同步到GitHub库里（反正不是打篮球那个库里）。
+10. 提交一个[QMK 固件的pull request](https://github.com/qmk/qmk_firmware/pull/new/master)。
+11. 给你的pull request拟一个标题，包括简短的描述和问题或错误代码。比如, 你可以起一个这样的"Added more log outputting to resolve #4352"（最好用英语，毕竟Q酱的中文也不是那么的溜，有可能会看不懂中文）。
+12. 在描述（description）里面写你做了哪些更改，你的代码里还存在什么问题, 或者你想问维护的小可爱们的问题。你的your pull request有点小问题无伤大雅(本来也没有完美的代码嘛), 维护的小可爱们会竭尽全力帮您改进的！
+13. 维护人员审查代码可能需要一些时间。
+14. 维护人员会通知您要更改什么地方，然后您就按照建议改一改。
+15. 预祝您合并成功！
+
+# 代码规范
+
+其实也没有什么特别严格的规范啦，但是俗话说的好：没有规矩，不成方圆。您可以看一下您的要改动的代码周围的画风，然后保持队形。如果你感觉周围都不知道是什么牛鬼蛇神的话就看看下面的建议：
+
+* 我们用肆(4)个空格来缩进(软件中也可以设置到Tab键)
+* 我们使用改良的1TBS(允许单行样式)
+  * 左大括号: 在开放性语句块那行的末尾
+  * 右大括号: 和开放性语句块第一个字母对齐
+  * Else If: 将右大括号放在行的开头，下一个左大括号放在同一行的结尾
+  * 可选大括号: 可选大括号是必选的
+    * 应该这样: if (condition) { return false; }
+    * 不应该这样: if (condition) return false;
+* 建议使用C语言风格的注释: `/* */`
+  * 把注释想象成一个描述特征的故事
+  * 充分使用注释来描述你为何这样修改
+  * 有些公认的东西就不要写到注释里面了
+  * 如果你不知道注释是否多余,看下面
+* 一般不要主动换行，主动换行的话每行不要超过76列
+* 要把 `#pragma once` 放到头文件的开始哦，抛弃老土的(`#ifndef THIS_FILE_H`, `#define THIS_FILE_H`, ..., `#endif`)吧
+* 下面两种预处理命令都可以用: `#ifdef DEFINED` 还有 `#if defined(DEFINED)`
+  * 以上那句对处女座不是很友好哈，处女座的朋友们就别纠结了，直接 `#if defined(DEFINED)` 。
+  * 还有就是选好一种风格就一直用，一直用一直爽，不要朝三暮四, 除非你要变化到多重条件的 `#if`。
+  * `#` 和 `if`要挨在一起哦，再让本空格在中间冒充电灯泡本空格会生气的。
+  * 以下是缩进规则:
+    * 首先考虑可读性，强迫症的朋友们总想要保持代码的高一致性，这样可不好。
+    * 保证文件已有风格不变。如果代码本来就是杂糅风格，那就见机行事，让你的修改更有意义些。
+    * 其实你也可以在缩进的时候看看周围其他代码，然后范水模山，预处理命令可以有自己的缩进风格。
+
+可以参照下面:
+
+```c
+/* foo 的 Enums*/
+enum foo_state {
+  FOO_BAR,
+  FOO_BAZ,
+};
+
+/* 有返回值的情况 */
+int foo(void) {
+  if (some_condition) {
+    return FOO_BAR;
+  } else {
+    return -1;
+  }
+}
+```
+
+# Clang-format的自动格式化
+[Clang-format](https://clang.llvm.org/docs/ClangFormat.html) 是LLVM的一部分，可以帮你自动格式化代码。我们给你准备好了一个适用于以上规范的配置文件，会帮你调整缩进和换行，你只需要写好括号就好。有了它，你再也不用担心调整代码格式太耗时，没有时间陪伴自己（虚构）的另一半了。
+
+使用[LLVM 完整安装](http://llvm.org/builds/)可以在Windows上安装clang-format, Ubuntu用户要用`sudo apt install clang-format`。
+
+命令行的朋友们, 加上 `-style=file`选项就会自动在QMK的根目录寻找.clang-format配置文件了。
+
+VSCode用户, 标准的 C/C++ 插件就支持clang-format, 或者可以用[独立扩展](https://marketplace.visualstudio.com/items?itemName=LLVMExtensions.ClangFormat)也行。
+
+有些东西(比如LAYOUT宏) 会被clang-format打乱，所以那些文件就别用clang-format了,这里就教您一个小窍门，在`// clang-format off` 和 `//clang-format on`之间装上会被搞乱的代码就好了。
+
+# 一般教程
+
+你可以给Q酱的不同部分添砖加瓦，但也要用不同的方法严谨检查。不论你修改哪里最好还是看看下边。
+
+* 将PR（pull request）分成一个个的逻辑单元。 比如，不要一次将两个新特性PR出去。要添加的特性排好队，一个一个来。
+* 提交之前看一眼，`git diff --check`的空格一定要写对了
+* 确定你的代码能通过编译
+  * 布局: 确定`make keyboard:your_new_keymap` 不返回错误
+  * 键盘: 确定 `make keyboard:all` 不返回错误
+  * 核心代码: 确定 `make all` 不返回错误
+* 提交的信息尽量明确。第一行写点简短介绍(每行不多于70个英文字母), 第二行空着,第三行和后面就要写些必要的细节了。最好用英文写，比如:
+
+```
+Adjust the fronzlebop for the kerpleplork
+
+The kerpleplork was intermittently failing with error code 23. The root cause was the fronzlebop setting, which causes the kerpleplork to activate every N iterations.
+
+Limited experimentation on the devices I have available shows that 7 is high enough to avoid confusing the kerpleplork, but I'd like to get some feedback from people with ARM devices to be sure.
+```
+
+## 文档
+
+想帮助Q酱当然是先看文档最简单了。找到这个文档哪里错了然后改正它对于你来说超级简单! 我们也对有写文档能力的人求贤若渴，如果你是对的人[点这个](#Q酱，我在哪能帮助你嘞?)!
+
+文档呢，都静静的放在`qmk_firmware/docs` 目录里, 也或者您想为网页做贡献的话也是可以的哦。
+
+在文档中附代码案例时, 先观察文档其他地方的命名规范。比如, 把enums的名字都改成像`my_layers`或者`my_keycodes`来防止名字不一致的enums被当作特务枪毙:
+
+```c
+enum my_layers {
+  _FIRST_LAYER,
+  _SECOND_LAYER
+};
+
+enum my_keycodes {
+  FIRST_LAYER = SAFE_RANGE,
+  SECOND_LAYER
+};
+```
+
+## 布局
+
+大多数QMK新手都从创建一个自己的布局开始。我们尽力保证布局规范宽松 (毕竟布局是个性的体现) 不过建议遵守以下准则，这样可以让别人更好理解你的代码
+
+* 用 [模板](documentation_templates.md)写个`readme.md`。
+* 所有的布局PR都会被squash, 如果你想知道你的提交是怎么被squash的那你就自己来吧
+* 不要把新特性和布局一起PR。可以分别PR他们
+* 布局文件夹就不要放`Makefile`了，这个操作都过时啦
+* 更新文件头部的copyrights(看`%YOUR_NAME%`那)
+
+## 键盘
+
+QMK的最终归宿是键盘。有些键盘是社区维护的，有一些是制作这些键盘的人维护的。`readme.md`会告诉你是谁维护了这个键盘，如果你对某个键盘有疑问，可以 [创建一个Issue](https://github.com/qmk/qmk_firmware/issues) 来问一问维护者。
+
+我们建议你按下面的来操作:
+
+* 用[模板](documentation_templates.md)写`readme.md`。
+* 提交数量尽量合理，不然我们可就要把你的PR给squash了。
+* 不要把新特性和新键盘一起PR。可以分别PR他们
+* 用父文件夹的名字命名 `.c`/`.h`文件, 比如`/keyboards/<kb1>/<kb2>/<kb2>.[ch]`
+* 键盘文件夹就不要放`Makefile`了，这个操作都过时啦
+* 更新文件头部的copyrights(看`%YOUR_NAME%`那)
+
+## Quantum/TMK 核心
+
+在您废寝忘食地开发Q酱新特性或者帮Q酱驱虫之前，一定要确保你的工作是有意义的。看看[了解QMK](understanding_qmk.md)你会对Q酱有更深的了解，这个文档将带你领略QMK的程序流程。现在你应该和维护团对谈谈来了解实现你想法的最佳方法了。一下渠道都可以：
+
+* [在Discord交流](https://discord.gg/Uq7gcHh)
+* [建立一个Issue](https://github.com/qmk/qmk_firmware/issues/new)
+
+新特性和BUG的修复影响所有键盘。开发组也在翻修QMK。所以，在实施重大返修之前一定要讨论一下。如果你在没有事先与维护团队沟通的情况下提交了一个PR，而且你的选择与维护团队的计划方向不符，那你可能要面临大改了。
+
+修复BUG或者开发新特性之前看看这个：
+
+* **默认不启用** - QMK运行的芯片多数内存有限，所以首要考虑的还应该是布局不要被破坏，于是特性默认是不启用的。你喜欢什么特性的话就打开它，如果你觉得有些特性应该默认开启或者你能帮助缩减代码，那就联系维护组吧。
+* **提交之前在本地编译** - 这个简直就是家喻户晓了，但是也确实需要编译啊！ 我们的Travis系统会发现一切问题，但是自己编译一下可要比在线等快多了。
+* **注意版本和芯片平台** - 有那么几个键盘有支持不同配置甚至是不同芯片的版本。试着写一个能AVR和ARM两个平台运行的特性，或者在不支持的平台自动禁用。
+* **解释你的新特性** - 在`docs/`写个文档, 你可以创建新文档或者写到现有文档中。如果你不把它记录下来，其他人就无法从你的努力中获益。
+
+也可以看看以下建议：
+
+* 提交数量尽量合理，不然我们可就要把你的PR给squash了。
+* 不要把新特性、布局和键盘一起PR。可以分别PR他们。
+* 给你的特性写[单元测试](unit_testing.md)。
+* 你编辑的文件风格要一致，如果风格不明确或者是混搭风的，你就要先看看[代码规范](#代码规范)确认情况。
+
+## 重构
+
+为了保持QMK脉络清晰，Q酱打算深入规划重构一下自己，然后让合作者进行修改。如果你有重构的思路或建议[创建一个issue](https://github.com/qmk/qmk_firmware/issues), Q酱很乐意讨论一下怎么改进一下。
+
+# 行为守则对于我来说有何意义?
+
+我们的[行为守则](https://github.com/qmk/qmk_firmware/blob/master/CODE_OF_CONDUCT.md) 是说明您有责任尊重和礼貌地对待项目中的每个人，无论他们的身份如何。 如果你是我们行为准则所描述的不当行为的受害者，我们将站在你这边，并按照行为准则对施暴者进行适当谴责。

docs/zh-cn/faq.md

@@ -0,0 +1,6 @@
+# 常见问题
+
+* [一般问题](faq_general.md)
+* [构建和编译QMK](faq_build.md)
+* [QMK调试和故障排除](faq_debug.md)
+* [布局问题](faq_keymap.md)

docs/zh-cn/getting_started_getting_help.md

@@ -0,0 +1,15 @@
+# 获得帮助
+
+有很多方法来获得关于QMK的帮助.
+
+## 实时聊天
+
+你可以在我们的主要[Discord服务器](https://discord.gg/Uq7gcHh)找到QMK的开发者和用户。有很多讨论固件的不同频道, 工具箱(Toolbox), 硬件,配置工具(configurator).
+
+## OLKB Subreddit
+
+QMK的官方论坛是[/r/olkb](https://reddit.com/r/olkb) 在[reddit.com](https://reddit.com)上.
+
+## Github的Issue
+
+你可以在GitHub上 [提出issue](https://github.com/qmk/qmk_firmware/issues).当您的问题需要长期讨论或调试时，这尤其方便。

docs/zh-cn/getting_started_github.md

@@ -0,0 +1,59 @@
+# 如何在QMK中使用Github
+
+Github can be a little tricky to those that aren't familiar with it - this guide will walk through each step of forking, cloning, and submitting a pull request with QMK.
+
+?> 本教程假设您已安装GitHub，并且您喜欢使用命令行工作。
+
+首先 [Github上的QMK页面](https://github.com/qmk/qmk_firmware), 您能看到右上方有个按钮写着"Fork":
+
+![从Github上分叉](http://i.imgur.com/8Toomz4.jpg)
+
+如果你是某组织成员，你将需要选择分叉到哪个账户。一般情况下, 你是想要分叉到你的私人账户下。当你完成分叉 (有时需要等一会), 点击"Clone or Download" 按钮:
+
+!从Github下载](http://i.imgur.com/N1NYcSz.jpg)
+
+你要选择 "HTTPS", 然后选择链接复制:
+
+![HTTPS链接](http://i.imgur.com/eGO0ohO.jpg)
+
+然后，在命令行输入`git clone `，然后粘贴你的链接:
+
+```
+user@computer:~$ git clone https://github.com/whoeveryouare/qmk_firmware.git
+Cloning into 'qmk_firmware'...
+remote: Counting objects: 46625, done.
+remote: Compressing objects: 100% (2/2), done.
+remote: Total 46625 (delta 0), reused 0 (delta 0), pack-reused 46623
+Receiving objects: 100% (46625/46625), 84.47 MiB | 3.14 MiB/s, done.
+Resolving deltas: 100% (29362/29362), done.
+Checking out files: 100% (2799/2799), done.
+```
+
+现在你本地计算机有QMK的分叉了,你可以添加你的布局了, 为你的键盘编译并刷新固件吧。如果你觉得你的修改很不错, 你可以添加,提交,然后想你的分叉推出（pull）你的改变，像这样:
+
+```
+user@computer:~$ git add .
+user@computer:~$ git commit -m "adding my keymap"
+[master cccb1608] adding my keymap
+ 1 file changed, 1 insertion(+)
+ create mode 100644 keyboards/planck/keymaps/mine/keymap.c
+user@computer:~$ git push
+Counting objects: 1, done.
+Delta compression using up to 4 threads.
+Compressing objects: 100% (1/1), done.
+Writing objects: 100% (1/1), 1.64 KiB | 0 bytes/s, done.
+Total 1 (delta 1), reused 0 (delta 0)
+remote: Resolving deltas: 100% (1/1), completed with 1 local objects.
+To https://github.com/whoeveryouare/qmk_firmware.git
+ + 20043e64...7da94ac5 master -> master
+```
+
+现在你的改动已经在你Github上的分支中了 - 如果你回到这 (`https://github.com/你的GitHub账户名/qmk_firmware`) ,你可以点击下方所示按钮创建 "New Pull Request":
+
+![新的 Pull Request](http://i.imgur.com/DxMHpJ8.jpg)
+
+现在你可以看到你所做的一切 - 如果看起来不错, 就可以点击 "Create Pull Request"定稿了:
+
+![创建Pull Request](http://i.imgur.com/Ojydlaj.jpg)
+
+提交后,我们会开跟你说你的改动,要求您进行更改, 并最终接受您的更改!感谢您为QMK做的贡献 :)

docs/zh-cn/newbs.md

@@ -0,0 +1,23 @@
+# QMK菜鸟教程
+
+QMK是为你机械硬盘设计的的一个强大的开源固件。使用QMK可以很简单的让你的定制键盘变得强大。看完这篇文章，无论你是菜鸟还是大佬，都可以顺利的使用QMK来定制键盘。
+
+你是否为不知道你的键盘能不能运行QMK而苦恼? 如果你的机械键盘是你自己做的，那么这把键盘一般可以运行QMK。我们提供了[一大堆自制键盘](http://qmk.fm/keyboards/), 所以即便你的键盘不能运行QMK你也很容易能找到满足你需求的键盘。
+
+## 概览
+
+这个教程有7个主要部分：
+
+* [新手上路](newbs_getting_started.md)
+* [用命令行构建你的第一个固件](newbs_building_firmware.md)
+* [用在线界面构建你的第一个固件](newbs_building_firmware_configurator.md)
+* [刷新固件](newbs_flashing.md)
+* [测试和调试](newbs_testing_debugging.md)
+* [Git最佳实践](newbs_best_practices.md)
+* [其他学习资源](newbs_learn_more_resources.md)
+
+这份教程旨在帮助没有固件构建经验的人，也是根据该目的做出选择和建议。这些程序有很多替代方法，大部分替代我们都支持。如果你对完成一个任务有疑问，可以[向我们寻求帮助](getting_started_getting_help.md).
+
+## 其他资源
+
+* [Thomas Baart的 QMK基础博客](https://thomasbaart.nl/category/mechanical-keyboards/firmware/qmk/qmk-basics/) – 这是一个用户创建的博客，涵盖了为新手准备的使用QMK的基础知识。

drivers/issi/is31fl3733.c

@@ -75,10 +75,10 @@ uint8_t g_twi_transfer_buffer[20];
 // buffers and the transfers in IS31FL3733_write_pwm_buffer() but it's
 // probably not worth the extra complexity.
 uint8_t g_pwm_buffer[DRIVER_COUNT][192];
-bool g_pwm_buffer_update_required = false;
+bool g_pwm_buffer_update_required[DRIVER_COUNT] = { false };
 
 uint8_t g_led_control_registers[DRIVER_COUNT][24] = { { 0 }, { 0 } };
-bool g_led_control_registers_update_required = false;
+bool g_led_control_registers_update_required[DRIVER_COUNT] = { false };
 
 void IS31FL3733_write_register( uint8_t addr, uint8_t reg, uint8_t data )
 {
@@ -123,12 +123,13 @@ void IS31FL3733_write_pwm_buffer( uint8_t addr, uint8_t *pwm_buffer )
     }
 }
 
-void IS31FL3733_init( uint8_t addr )
+void IS31FL3733_init( uint8_t addr, uint8_t sync)
 {
     // In order to avoid the LEDs being driven with garbage data
     // in the LED driver's PWM registers, shutdown is enabled last.
     // Set up the mode and other settings, clear the PWM registers,
     // then disable software shutdown.
+    // Sync is passed so set it according to the datasheet.
 
     // Unlock the command register.
     IS31FL3733_write_register( addr, ISSI_COMMANDREGISTER_WRITELOCK, 0xC5 );
@@ -161,7 +162,7 @@ void IS31FL3733_init( uint8_t addr )
     // Set global current to maximum.
     IS31FL3733_write_register( addr, ISSI_REG_GLOBALCURRENT, 0xFF );
     // Disable software shutdown.
-    IS31FL3733_write_register( addr, ISSI_REG_CONFIGURATION, 0x01 );
+    IS31FL3733_write_register( addr, ISSI_REG_CONFIGURATION, (sync << 6) | 0x01 );
 
     // Wait 10ms to ensure the device has woken up.
     #ifdef __AVR__
@@ -179,7 +180,7 @@ void IS31FL3733_set_color( int index, uint8_t red, uint8_t green, uint8_t blue )
         g_pwm_buffer[led.driver][led.r] = red;
         g_pwm_buffer[led.driver][led.g] = green;
         g_pwm_buffer[led.driver][led.b] = blue;
-        g_pwm_buffer_update_required = true;
+        g_pwm_buffer_update_required[led.driver] = true;
     }
 }
 
@@ -218,35 +219,34 @@ void IS31FL3733_set_led_control_register( uint8_t index, bool red, bool green, b
         g_led_control_registers[led.driver][control_register_b] &= ~(1 << bit_b);
     }
 
-    g_led_control_registers_update_required = true;
+    g_led_control_registers_update_required[led.driver] = true;
 
 }
 
-void IS31FL3733_update_pwm_buffers( uint8_t addr1, uint8_t addr2 )
+void IS31FL3733_update_pwm_buffers( uint8_t addr, uint8_t index )
 {
-    if ( g_pwm_buffer_update_required )
+    if ( g_pwm_buffer_update_required[index] )
     {
         // Firstly we need to unlock the command register and select PG1
-        IS31FL3733_write_register( addr1, ISSI_COMMANDREGISTER_WRITELOCK, 0xC5 );
-        IS31FL3733_write_register( addr1, ISSI_COMMANDREGISTER, ISSI_PAGE_PWM );
+        IS31FL3733_write_register( addr, ISSI_COMMANDREGISTER_WRITELOCK, 0xC5 );
+        IS31FL3733_write_register( addr, ISSI_COMMANDREGISTER, ISSI_PAGE_PWM );
 
-        IS31FL3733_write_pwm_buffer( addr1, g_pwm_buffer[0] );
-        //IS31FL3733_write_pwm_buffer( addr2, g_pwm_buffer[1] );
+        IS31FL3733_write_pwm_buffer( addr, g_pwm_buffer[index] );
     }
-    g_pwm_buffer_update_required = false;
+    g_pwm_buffer_update_required[index] = false;
 }
 
-void IS31FL3733_update_led_control_registers( uint8_t addr1, uint8_t addr2 )
+void IS31FL3733_update_led_control_registers( uint8_t addr, uint8_t index )
 {
-    if ( g_led_control_registers_update_required )
+    if ( g_led_control_registers_update_required[index] )
     {
         // Firstly we need to unlock the command register and select PG0
-        IS31FL3733_write_register( addr1, ISSI_COMMANDREGISTER_WRITELOCK, 0xC5 );
-        IS31FL3733_write_register( addr1, ISSI_COMMANDREGISTER, ISSI_PAGE_LEDCONTROL );
+        IS31FL3733_write_register( addr, ISSI_COMMANDREGISTER_WRITELOCK, 0xC5 );
+        IS31FL3733_write_register( addr, ISSI_COMMANDREGISTER, ISSI_PAGE_LEDCONTROL );
         for ( int i=0; i<24; i++ )
         {
-            IS31FL3733_write_register(addr1, i, g_led_control_registers[0][i] );
-            //IS31FL3733_write_register(addr2, i, g_led_control_registers[1][i] );
+            IS31FL3733_write_register(addr, i, g_led_control_registers[index][i] );
         }
     }
+    g_led_control_registers_update_required[index] = false;
 }

drivers/issi/is31fl3733.h

@@ -32,7 +32,7 @@ typedef struct is31_led {
 
 extern const is31_led g_is31_leds[DRIVER_LED_TOTAL];
 
-void IS31FL3733_init( uint8_t addr );
+void IS31FL3733_init( uint8_t addr, uint8_t sync );
 void IS31FL3733_write_register( uint8_t addr, uint8_t reg, uint8_t data );
 void IS31FL3733_write_pwm_buffer( uint8_t addr, uint8_t *pwm_buffer );
 
@@ -45,8 +45,8 @@ void IS31FL3733_set_led_control_register( uint8_t index, bool red, bool green, b
 // (eg. from a timer interrupt).
 // Call this while idle (in between matrix scans).
 // If the buffer is dirty, it will update the driver with the buffer.
-void IS31FL3733_update_pwm_buffers( uint8_t addr1, uint8_t addr2 );
-void IS31FL3733_update_led_control_registers( uint8_t addr1, uint8_t addr2 );
+void IS31FL3733_update_pwm_buffers( uint8_t addr, uint8_t index );
+void IS31FL3733_update_led_control_registers( uint8_t addr, uint8_t index );
 
 #define A_1  0x00
 #define A_2  0x01

keyboards/40percentclub/nein/config.h

@@ -0,0 +1,239 @@
+/* Copyright 2019
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0xFEED
+#define PRODUCT_ID      0x0A0C
+#define DEVICE_VER      0x9999
+#define MANUFACTURER    di0ib
+#define PRODUCT         The nein Keyboard
+#define DESCRIPTION     9 key macropad
+
+/* key matrix size */
+#define MATRIX_ROWS 3
+#define MATRIX_COLS 3
+
+/* Keyboard Matrix Assignments */
+#define DIRECT_PINS { \
+    { F4, F5, F6 }, \
+    { F7, B1, B3 }, \
+    { B2, B6, B5 }  \
+}
+#define UNUSED_PINS
+
+/*
+ * Split Keyboard specific options, make sure you have 'SPLIT_KEYBOARD = yes' in your rules.mk, and define SOFT_SERIAL_PIN.
+ */
+// #define SOFT_SERIAL_PIN D0 // or D1, D2, D3, E6
+
+// #define BACKLIGHT_PIN B7
+// #define BACKLIGHT_BREATHING
+// #define BACKLIGHT_LEVELS 3
+
+// #define RGB_DI_PIN E2
+// #ifdef RGB_DI_PIN
+//   #define RGBLED_NUM 16
+//   #define RGBLIGHT_HUE_STEP 8
+//   #define RGBLIGHT_SAT_STEP 8
+//   #define RGBLIGHT_VAL_STEP 8
+//   #define RGBLIGHT_LIMIT_VAL 255 /* The maximum brightness level */
+//   #define RGBLIGHT_SLEEP  /* If defined, the RGB lighting will be switched off when the host goes to sleep */
+// /*== all animations enable ==*/
+//   #define RGBLIGHT_ANIMATIONS
+// /*== or choose animations ==*/
+//   #define RGBLIGHT_EFFECT_BREATHING
+//   #define RGBLIGHT_EFFECT_RAINBOW_MOOD
+//   #define RGBLIGHT_EFFECT_RAINBOW_SWIRL
+//   #define RGBLIGHT_EFFECT_SNAKE
+//   #define RGBLIGHT_EFFECT_KNIGHT
+//   #define RGBLIGHT_EFFECT_CHRISTMAS
+//   #define RGBLIGHT_EFFECT_STATIC_GRADIENT
+//   #define RGBLIGHT_EFFECT_RGB_TEST
+//   #define RGBLIGHT_EFFECT_ALTERNATING
+// /*== customize breathing effect ==*/
+//   /*==== (DEFAULT) use fixed table instead of exp() and sin() ====*/
+//   #define RGBLIGHT_BREATHE_TABLE_SIZE 256      // 256(default) or 128 or 64
+//   /*==== use exp() and sin() ====*/
+//   #define RGBLIGHT_EFFECT_BREATHE_CENTER 1.85  // 1 to 2.7
+//   #define RGBLIGHT_EFFECT_BREATHE_MAX    255   // 0 to 255
+// #endif
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCING_DELAY 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/* If defined, GRAVE_ESC will always act as ESC when CTRL is held.
+ * This is userful for the Windows task manager shortcut (ctrl+shift+esc).
+ */
+// #define GRAVE_ESC_CTRL_OVERRIDE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/* key combination for magic key command */
+/* defined by default; to change, uncomment and set to the combination you want */
+// #define IS_COMMAND() (get_mods() == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)))
+
+/* control how magic key switches layers */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
+
+/* override magic key keymap */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
+//#define MAGIC_KEY_HELP           H
+//#define MAGIC_KEY_HELP_ALT       SLASH
+//#define MAGIC_KEY_DEBUG          D
+//#define MAGIC_KEY_DEBUG_MATRIX   X
+//#define MAGIC_KEY_DEBUG_KBD      K
+//#define MAGIC_KEY_DEBUG_MOUSE    M
+//#define MAGIC_KEY_VERSION        V
+//#define MAGIC_KEY_STATUS         S
+//#define MAGIC_KEY_CONSOLE        C
+//#define MAGIC_KEY_LAYER0         0
+//#define MAGIC_KEY_LAYER0_ALT     GRAVE
+//#define MAGIC_KEY_LAYER1         1
+//#define MAGIC_KEY_LAYER2         2
+//#define MAGIC_KEY_LAYER3         3
+//#define MAGIC_KEY_LAYER4         4
+//#define MAGIC_KEY_LAYER5         5
+//#define MAGIC_KEY_LAYER6         6
+//#define MAGIC_KEY_LAYER7         7
+//#define MAGIC_KEY_LAYER8         8
+//#define MAGIC_KEY_LAYER9         9
+//#define MAGIC_KEY_BOOTLOADER     B
+//#define MAGIC_KEY_BOOTLOADER_ALT ESC
+//#define MAGIC_KEY_LOCK           CAPS
+//#define MAGIC_KEY_EEPROM         E
+//#define MAGIC_KEY_EEPROM_CLEAR   BSPACE
+//#define MAGIC_KEY_NKRO           N
+//#define MAGIC_KEY_SLEEP_LED      Z
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+/*
+ * MIDI options
+ */
+
+/* Prevent use of disabled MIDI features in the keymap */
+//#define MIDI_ENABLE_STRICT 1
+
+/* enable basic MIDI features:
+   - MIDI notes can be sent when in Music mode is on
+*/
+//#define MIDI_BASIC
+
+/* enable advanced MIDI features:
+   - MIDI notes can be added to the keymap
+   - Octave shift and transpose
+   - Virtual sustain, portamento, and modulation wheel
+   - etc.
+*/
+//#define MIDI_ADVANCED
+
+/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
+//#define MIDI_TONE_KEYCODE_OCTAVES 1
+
+/*
+ * HD44780 LCD Display Configuration
+ */
+/*
+#define LCD_LINES           2     //< number of visible lines of the display
+#define LCD_DISP_LENGTH    16     //< visibles characters per line of the display
+#define LCD_IO_MODE      1            //< 0: memory mapped mode, 1: IO port mode
+#if LCD_IO_MODE
+#define LCD_PORT         PORTB        //< port for the LCD lines
+#define LCD_DATA0_PORT   LCD_PORT     //< port for 4bit data bit 0
+#define LCD_DATA1_PORT   LCD_PORT     //< port for 4bit data bit 1
+#define LCD_DATA2_PORT   LCD_PORT     //< port for 4bit data bit 2
+#define LCD_DATA3_PORT   LCD_PORT     //< port for 4bit data bit 3
+#define LCD_DATA0_PIN    4            //< pin for 4bit data bit 0
+#define LCD_DATA1_PIN    5            //< pin for 4bit data bit 1
+#define LCD_DATA2_PIN    6            //< pin for 4bit data bit 2
+#define LCD_DATA3_PIN    7            //< pin for 4bit data bit 3
+#define LCD_RS_PORT      LCD_PORT     //< port for RS line
+#define LCD_RS_PIN       3            //< pin  for RS line
+#define LCD_RW_PORT      LCD_PORT     //< port for RW line
+#define LCD_RW_PIN       2            //< pin  for RW line
+#define LCD_E_PORT       LCD_PORT     //< port for Enable line
+#define LCD_E_PIN        1            //< pin  for Enable line
+#endif
+*/
+
+/* Bootmagic Lite key configuration */
+// #define BOOTMAGIC_LITE_ROW 0
+// #define BOOTMAGIC_LITE_COLUMN 0

keyboards/40percentclub/nein/info.json

@@ -0,0 +1,22 @@
+{
+  "keyboard_name": "nein",
+  "url": "",
+  "maintainer": "qmk",
+  "width": 3,
+  "height": 3,
+  "layouts": {
+    "LAYOUT": {
+      "layout": [
+        {"x":0, "y":0},
+        {"x":1, "y":0},
+        {"x":2, "y":0},
+        {"x":0, "y":1},
+        {"x":1, "y":1},
+        {"x":2, "y":1},
+        {"x":0, "y":2},
+        {"x":1, "y":2},
+        {"x":2, "y":2}
+      ]
+    }
+  }
+}

keyboards/40percentclub/nein/keymaps/default/keymap.c

@@ -0,0 +1,29 @@
+/* Copyright 2019
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include QMK_KEYBOARD_H
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+    [0] = LAYOUT_ortho_3x3(
+        KC_MUTE, KC_HOME, KC_MPLY, \
+        MO(1),   KC_UP,   KC_END, \
+        KC_LEFT, KC_DOWN, KC_RGHT \
+    ),
+    [1] = LAYOUT_ortho_3x3(
+        RESET,   _______, KC_STOP, \
+        _______, _______, RGB_MOD, \
+        KC_MPRV, _______, KC_MNXT \
+    ),
+};

keyboards/40percentclub/nein/nein.c

@@ -0,0 +1,16 @@
+/* Copyright 2019
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include "nein.h"

keyboards/40percentclub/nein/nein.h

@@ -0,0 +1,37 @@
+/* Copyright 2019
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#pragma once
+
+#include "quantum.h"
+
+/* This a shortcut to help you visually see your layout.
+ *
+ * The first section contains all of the arguments representing the physical
+ * layout of the board and position of the keys.
+ *
+ * The second converts the arguments into a two-dimensional array which
+ * represents the switch matrix.
+ */
+#define LAYOUT_ortho_3x3( \
+    k00, k01, k02, \
+    k10, k11, k12, \
+    k20, k21, k22  \
+) \
+{ \
+    { k00, k01, k02 }, \
+    { k10, k11, k12 }, \
+    { k20, k21, k22 }  \
+}

keyboards/40percentclub/nein/readme.md

@@ -0,0 +1,18 @@
+# nein
+
+![nein](https://2.bp.blogspot.com/-avYV4grcAPQ/XL9a67SxgKI/AAAAAAACVCE/GSGVYRThaEEDd14M3LG34gQTv5ZabRI0QCEwYBhgL/s640/a.jpg)
+===
+
+A 9 key macropad.
+
+Powered by a Pro Micro and can fit any of the various different sized variations of Pro Micro.
+
+Keyboard Maintainer: QMK Community  
+Hardware Supported: nein PCB  
+Hardware Availability: [nein project on 40% Keyboards](https://www.40percent.club/2019/04/nein.html)
+
+Make example for this keyboard (after setting up your build environment):
+
+    make 40percentclub/nein:default
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/40percentclub/nein/rules.mk

@@ -0,0 +1,80 @@
+# MCU name
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   atmega32a    bootloadHID
+BOOTLOADER = caterina
+
+
+# If you don't know the bootloader type, then you can specify the
+# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
+#   Teensy halfKay      512
+#   Teensy++ halfKay    1024
+#   Atmel DFU loader    4096
+#   LUFA bootloader     4096
+#   USBaspLoader        2048
+# OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE = lite     # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = no         # Console for debug(+400)
+COMMAND_ENABLE = no         # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE = yes           # USB Nkey Rollover
+BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality on B7 by default
+RGBLIGHT_ENABLE = no        # Enable keyboard RGB underglow
+MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no           # Audio output on port C6
+FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
+HD44780_ENABLE = no 	    # Enable support for HD44780 based LCDs (+400)

keyboards/ai03/lunar/info.json

@@ -7,7 +7,78 @@
     "height": 5, 
     "layouts": {
         "LAYOUT": {
-            "layout": [{"label":"Esc", "x":0, "y":0}, {"label":"!", "x":1, "y":0}, {"label":"@", "x":2, "y":0}, {"label":"#", "x":3, "y":0}, {"label":"$", "x":4, "y":0}, {"label":"%", "x":5, "y":0}, {"label":"^", "x":6, "y":0}, {"label":"&", "x":7, "y":0}, {"label":"*", "x":8, "y":0}, {"label":"(", "x":9, "y":0}, {"label":")", "x":10, "y":0}, {"label":"_", "x":11, "y":0}, {"label":"+", "x":12, "y":0}, {"label":"Backspace", "x":13, "y":0, "w":2}, {"label":"Insert", "x":15, "y":0}, {"label":"Tab", "x":0, "y":1, "w":1.5}, {"label":"Q", "x":1.5, "y":1}, {"label":"W", "x":2.5, "y":1}, {"label":"E", "x":3.5, "y":1}, {"label":"R", "x":4.5, "y":1}, {"label":"T", "x":5.5, "y":1}, {"label":"Y", "x":6.5, "y":1}, {"label":"U", "x":7.5, "y":1}, {"label":"I", "x":8.5, "y":1}, {"label":"O", "x":9.5, "y":1}, {"label":"P", "x":10.5, "y":1}, {"label":"{", "x":11.5, "y":1}, {"label":"}", "x":12.5, "y":1}, {"label":"|", "x":13.5, "y":1, "w":1.5}, {"label":"Delete", "x":15, "y":1}, {"label":"Caps Lock", "x":0, "y":2, "w":1.75}, {"label":"A", "x":1.75, "y":2}, {"label":"S", "x":2.75, "y":2}, {"label":"D", "x":3.75, "y":2}, {"label":"F", "x":4.75, "y":2}, {"label":"G", "x":5.75, "y":2}, {"label":"H", "x":6.75, "y":2}, {"label":"J", "x":7.75, "y":2}, {"label":"K", "x":8.75, "y":2}, {"label":"L", "x":9.75, "y":2}, {"label":":", "x":10.75, "y":2}, {"label":"\"", "x":11.75, "y":2}, {"label":"Enter", "x":12.75, "y":2, "w":2.25}, {"label":"Home", "x":15, "y":2}, {"label":"Shift", "x":0, "y":3, "w":2.25}, {"label":"Z", "x":2.25, "y":3}, {"label":"X", "x":3.25, "y":3}, {"label":"C", "x":4.25, "y":3}, {"label":"V", "x":5.25, "y":3}, {"label":"B", "x":6.25, "y":3}, {"label":"N", "x":7.25, "y":3}, {"label":"M", "x":8.25, "y":3}, {"label":"<", "x":9.25, "y":3}, {"label":">", "x":10.25, "y":3}, {"label":"?", "x":11.25, "y":3}, {"label":"Shift", "x":12.25, "y":3, "w":1.75}, {"label":"\u2191", "x":14, "y":3}, {"label":"End", "x":15, "y":3}, {"label":"Ctrl", "x":0, "y":4, "w":1.5}, {"label":"Win", "x":1.5, "y":4, "w":1.25}, {"label":"Alt", "x":2.75, "y":4, "w":1.5}, {"x":4.25, "y":4, "w":2.25}, {"x":6.5, "y":4, "w":1.5}, {"x":8, "y":4, "w":2.75}, {"label":"Alt", "x":10.75, "y":4, "w":1.25}, {"label":"Win", "x":12, "y":4}, {"label":"\u2190", "x":13, "y":4}, {"label":"\u2193", "x":14, "y":4}, {"label":"\u2192", "x":15, "y":4}]
+            "layout": [
+                {"label":"Esc", "x":0, "y":0},
+                {"label":"!", "x":1, "y":0},
+                {"label":"@", "x":2, "y":0},
+                {"label":"#", "x":3, "y":0},
+                {"label":"$", "x":4, "y":0},
+                {"label":"%", "x":5, "y":0},
+                {"label":"^", "x":6, "y":0},
+                {"label":"&", "x":7, "y":0},
+                {"label":"*", "x":8, "y":0},
+                {"label":"(", "x":9, "y":0},
+                {"label":")", "x":10, "y":0},
+                {"label":"_", "x":11, "y":0},
+                {"label":"+", "x":12, "y":0},
+                {"label":"BackspaceL", "x":13, "y":0},
+                {"label":"BackspaceR", "x":14, "y":0},
+                {"label":"Insert", "x":15, "y":0},
+                {"label":"Tab", "x":0, "y":1, "w":1.5},
+                {"label":"Q", "x":1.5, "y":1},
+                {"label":"W", "x":2.5, "y":1},
+                {"label":"E", "x":3.5, "y":1},
+                {"label":"R", "x":4.5, "y":1},
+                {"label":"T", "x":5.5, "y":1},
+                {"label":"Y", "x":6.5, "y":1},
+                {"label":"U", "x":7.5, "y":1},
+                {"label":"I", "x":8.5, "y":1},
+                {"label":"O", "x":9.5, "y":1},
+                {"label":"P", "x":10.5, "y":1},
+                {"label":"{", "x":11.5, "y":1},
+                {"label":"}", "x":12.5, "y":1},
+                {"label":"|", "x":13.5, "y":1, "w":1.5},
+                {"label":"Delete", "x":15, "y":1},
+                {"label":"Caps Lock", "x":0, "y":2, "w":1.75},
+                {"label":"A", "x":1.75, "y":2},
+                {"label":"S", "x":2.75, "y":2},
+                {"label":"D", "x":3.75, "y":2},
+                {"label":"F", "x":4.75, "y":2},
+                {"label":"G", "x":5.75, "y":2},
+                {"label":"H", "x":6.75, "y":2},
+                {"label":"J", "x":7.75, "y":2},
+                {"label":"K", "x":8.75, "y":2},
+                {"label":"L", "x":9.75, "y":2},
+                {"label":":", "x":10.75, "y":2},
+                {"label":"\"", "x":11.75, "y":2},
+                {"label":"Enter", "x":12.75, "y":2, "w":2.25},
+                {"label":"Home", "x":15, "y":2},
+                {"label":"Shift", "x":0, "y":3, "w":2.25},
+                {"label":"Z", "x":2.25, "y":3},
+                {"label":"X", "x":3.25, "y":3},
+                {"label":"C", "x":4.25, "y":3},
+                {"label":"V", "x":5.25, "y":3},
+                {"label":"B", "x":6.25, "y":3},
+                {"label":"N", "x":7.25, "y":3},
+                {"label":"M", "x":8.25, "y":3},
+                {"label":"<", "x":9.25, "y":3},
+                {"label":">", "x":10.25, "y":3},
+                {"label":"?", "x":11.25, "y":3},
+                {"label":"Shift", "x":12.25, "y":3, "w":1.75},
+                {"label":"\u2191", "x":14, "y":3},
+                {"label":"End", "x":15, "y":3},
+                {"label":"Ctrl", "x":0, "y":4, "w":1.5},
+                {"label":"Win", "x":1.5, "y":4, "w":1.25},
+                {"label":"Alt", "x":2.75, "y":4, "w":1.5},
+                {"x":4.25, "y":4, "w":2.25},
+                {"x":6.5, "y":4, "w":1.5},
+                {"x":8, "y":4, "w":2.75},
+                {"label":"Alt", "x":10.75, "y":4, "w":1.25},
+                {"label":"Win", "x":12, "y":4},
+                {"label":"\u2190", "x":13, "y":4},
+                {"label":"\u2193", "x":14, "y":4},
+                {"label":"\u2192", "x":15, "y":4}
+            ]
         }
     }
 }

keyboards/ai03/orbit/info.json

@@ -0,0 +1,88 @@
+{
+    "keyboard_name": "orbit", 
+    "url": "https://github.com/ai03-2725/Orbit", 
+    "maintainer": "ai03", 
+    "width": 16, 
+    "height": 6, 
+    "layouts": {
+        "LAYOUT": {
+            "layout": [
+                {"x":0,  "y":0.63},
+                {"x":1,  "y":0.38},
+                {"x":2,  "y":0.38},
+                {"x":3,  "y":0.13},
+                {"x":4,  "y":0},
+                {"x":5,  "y":0.13},
+                {"x":6,  "y":0.25},
+                {"x":9,  "y":0.25},
+                {"x":10, "y":0.13},
+                {"x":11, "y":0},
+                {"x":12, "y":0.13},
+                {"x":13, "y":0.38},
+                {"x":14, "y":0.38},
+                {"x":15, "y":0.63},
+
+                {"x":0,  "y":1.63},
+                {"x":1,  "y":1.38},
+                {"x":2,  "y":1.38},
+                {"x":3,  "y":1.13},
+                {"x":4,  "y":1},
+                {"x":5,  "y":1.13},
+                {"x":6,  "y":1.25},
+                {"x":9,  "y":1.25},
+                {"x":10, "y":1.13},
+                {"x":11, "y":1},
+                {"x":12, "y":1.13},
+                {"x":13, "y":1.38},
+                {"x":14, "y":1.38},
+                {"x":15, "y":1.63},
+
+                {"x":0,  "y":2.63},
+                {"x":1,  "y":2.38},
+                {"x":2,  "y":2.38},
+                {"x":3,  "y":2.13},
+                {"x":4,  "y":2},
+                {"x":5,  "y":2.13},
+                {"x":6,  "y":2.25},
+                {"x":9,  "y":2.25},
+                {"x":10, "y":2.13},
+                {"x":11, "y":2},
+                {"x":12, "y":2.13},
+                {"x":13, "y":2.38},
+                {"x":14, "y":2.38},
+                {"x":15, "y":2.63},
+
+                {"x":0,  "y":3.63},
+                {"x":1,  "y":3.38},
+                {"x":2,  "y":3.38},
+                {"x":3,  "y":3.13},
+                {"x":4,  "y":3},
+                {"x":5,  "y":3.13},
+                {"x":6,  "y":3.25},
+                {"x":9,  "y":3.25},
+                {"x":10, "y":3.13},
+                {"x":11, "y":3},
+                {"x":12, "y":3.13},
+                {"x":13, "y":3.38},
+                {"x":14, "y":3.38},
+                {"x":15, "y":3.63},
+
+                {"x":1,  "y":4.38},
+                {"x":2,  "y":4.38},
+                {"x":3,  "y":4.13},
+                {"x":4,  "y":4},
+
+                {"x":5.5, "y":4.25},
+                {"x":6.5, "y":4.5, "h":1.5},
+
+                {"x":8.5, "y":4.5, "h":1.5},
+                {"x":9.5, "y":4.25},
+
+                {"x":11, "y":4},
+                {"x":12, "y":4.13},
+                {"x":13, "y":4.38},
+                {"x":14, "y":4.38}
+            ]
+        }
+    }
+}

keyboards/butterstick/keymaps/default/keymap.c

@@ -45,6 +45,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
 uint32_t processQwerty(bool lookup) {
     // SECRET AGENT CHORDS
     P( LSU | LK | RS | RD,    	SEND_STRING(VERSION); SEND_STRING(__DATE__));
+	P( LR  | ST2| RR | RB, 		SEND(KC_BSPC));
     P( LSD | RZ,   			 	SEND(KC_SPC));
 
     // Dual chords

keyboards/claw44/ssd1306.c

@@ -13,7 +13,7 @@
 #include "sendchar.h"
 #include "timer.h"
 
-static const unsigned char font[] PROGMEM;
+extern const unsigned char font[] PROGMEM;
 
 // Set this to 1 to help diagnose early startup problems
 // when testing power-on with ble.  Turn it off otherwise,

keyboards/comet46/ssd1306.c

@@ -13,7 +13,7 @@
 #include "sendchar.h"
 #include "timer.h"
 
-static const unsigned char font[] PROGMEM;
+extern const unsigned char font[] PROGMEM;
 
 // Set this to 1 to help diagnose early startup problems
 // when testing power-on with ble.  Turn it off otherwise,

keyboards/converter/modelm101/keymaps/default/keymap.c

@@ -21,7 +21,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
     KC_GRV,  KC_1,    KC_2,   KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    KC_MINS, KC_EQL,  KC_BSPC,   KC_INS,  KC_HOME, KC_PGUP,   KC_NLCK, KC_PSLS, KC_PAST, KC_PMNS,
     KC_TAB,  KC_Q,    KC_W,   KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_LBRC, KC_RBRC, KC_BSLS,   KC_DEL,  KC_END,  KC_PGDN,   KC_P7,   KC_P8,   KC_P9,   KC_PPLS,
     KC_CAPS, KC_A,    KC_S,   KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN, KC_QUOT, KC_NUHS, KC_ENT,                                 KC_P4,   KC_P5,   KC_P6,
-    KC_LSFT, KC_NUBS, KC_Z,   KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH,          KC_RSFT,            KC_UP,              KC_P1,   KC_P2,   KC_P3,   KC_LGUI,
+    KC_LSFT, KC_NUBS, KC_Z,   KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH,          KC_RSFT,            KC_UP,              KC_P1,   KC_P2,   KC_P3,   KC_PENT,
     KC_LCTL,          KC_LALT,                           KC_SPC,                                      KC_RALT,          KC_RCTL,   KC_LEFT, KC_DOWN, KC_RGHT,   KC_P0,            KC_PDOT
   ),
 };

keyboards/crkbd/ssd1306.c

@@ -13,7 +13,7 @@
 #include "sendchar.h"
 #include "timer.h"
 
-static const unsigned char font[] PROGMEM;
+extern const unsigned char font[] PROGMEM;
 
 // Set this to 1 to help diagnose early startup problems
 // when testing power-on with ble.  Turn it off otherwise,

keyboards/doro67/multi/multi.c

@@ -19,6 +19,7 @@ void matrix_init_kb(void) {
 	// put your keyboard start-up code here
 	// runs once when the firmware starts up
 
+    setPinOutput(E6);
 	matrix_init_user();
 }
 
@@ -39,5 +40,11 @@ bool process_record_kb(uint16_t keycode, keyrecord_t *record) {
 void led_set_kb(uint8_t usb_led) {
 	// put your keyboard LED indicator (ex: Caps Lock LED) toggling code here
 
+	if (IS_LED_ON(usb_led, USB_LED_CAPS_LOCK)) {
+		writePinLow(E6);
+	} else {
+		writePinHigh(E6);
+	}
+
 	led_set_user(usb_led);
 }

keyboards/dz60/dz60.h

@@ -404,13 +404,13 @@
     k10,      k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b, k1c, k1d,      \
     k20,      k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b, k2c, k1e, k2d, \
     k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3a, k3b,      k3d, k3e, \
-    k40, k41,      k43, k44,      k46,      k48,      k4a, k4b, k4c, k4d, k4e  \
+    k40, k41,      k43, k44,      k46,      k48,      k4a, k4b,      k4d, k4e  \
 ) { \
     { k00,  k01,   k02,   k03,  k04,  k05,   k06,  k07,   k08,  k09,   k0a,  k0b,   k0c,  k0d,  k0e   }, \
     { k10,  KC_NO, k12,   k13,  k14,  k15,   k16,  k17,   k18,  k19,   k1a,  k1b,   k1c,  k1d,  k1e   }, \
     { k20,  KC_NO, k22,   k23,  k24,  k25,   k26,  k27,   k28,  k29,   k2a,  k2b,   k2c,  k2d,  KC_NO }, \
     { k30,  k31,   k32,   k33,  k34,  k35,   k36,  k37,   k38,  k39,   k3a,  k3b,   KC_NO,k3d,  k3e   }, \
-    { k40,  k41,   KC_NO, k43,  k44,  KC_NO, k46,  KC_NO, k48,  KC_NO, k4a,  k4b,   k4c,  k4d,  k4e   }  \
+    { k40,  k41,   KC_NO, k43,  k44,  KC_NO, k46,  KC_NO, k48,  KC_NO, k4a,  k4b,   KC_NO,k4d,  k4e   }  \
 }
 
 #endif

keyboards/dz60/keymaps/billiams/keymap.c

@@ -28,9 +28,9 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
    * ,-----------------------------------------------------------------------------------------.
    * |     |  F1 |  F2 |  F3 |  F4 |  F5 |  F6 |  F7 |  F8 |  F9 | F10 | F11 | F12 |    DEL    |
    * |-----------------------------------------------------------------------------------------+
-   * |        |RBB T|RGB M| Hue-| Hue+| Sat-| Sat+| Val-| Val+|     |     | Mute | Prev | Next |
+   * |        |RBB T|RGB M| Hue-| Hue+| Sat-| Sat+| Val-| Val+| Mute | Vol-| Vol+| Prev | Next |
    * |-----------------------------------------------------------------------------------------+
-   * |         |     |     |     |     |     |     |     |    |     | Vol- | Vol+ | Play/Pause |
+   * |         |     |     |     |     |     | Left| Down| Up |Right|      |      | Play/Pause |
    * |-----------------------------------------------------------------------------------------+
    * |           |     |     |     |     |     |     |     |Scr- |Scr+ |           |PG_UP|RESET|
    * |-----------------------------------------------------------------------------------------+
@@ -40,8 +40,8 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
 
   LAYOUT_directional(
       _______, KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,  KC_F10, KC_F11, KC_F12, _______, KC_DEL,
-      _______, RGB_TOG, RGB_MOD, RGB_HUD, RGB_HUI, RGB_SAD, RGB_SAI, RGB_VAD, RGB_VAI, _______, _______, _______, KC_MRWD, KC_MFFD,
-      _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_MUTE, KC__VOLDOWN, KC__VOLUP,
+      _______, RGB_TOG, RGB_MOD, RGB_HUD, RGB_HUI, RGB_SAD, RGB_SAI, RGB_VAD, RGB_VAI, KC_MUTE, KC__VOLDOWN, KC__VOLUP, KC_MRWD, KC_MFFD,
+      _______, _______, _______, _______, _______, _______, KC_LEFT, KC_DOWN, KC_UP, KC_RIGHT, _______, _______,
       KC_MPLY, _______, _______, _______, _______, _______, _______, _______, _______, KC_BRID, KC_BRIU, _______, _______, KC_PGUP, RESET,
       _______, _______, _______, _______, _______, _______, _______, _______, KC_HOME, KC_PGDOWN, KC_END
       ),

keyboards/dz60/keymaps/billiams/readme.md

@@ -11,6 +11,7 @@ Settings:
 * `/ ?` are available when you tap the right shift. Otherwise RShift is shift when held down
 * RESET is available as `Fn`+ ` ESC`
 * Underglow toggle is available as `Fn` + `Q`. Yes your keyboard has lights even if you didn't get the LEDs. Bonus!
+* vim-style arrow key bindings H J K L in layer 1
 
 ### Initial Installation
 
@@ -59,9 +60,9 @@ FN Layer
 ,-----------------------------------------------------------------------------------------.
 |  `  |  F1 |  F2 |  F3 |  F4 |  F5 |  F6 |  F7 |  F8 |  F9 | F10 | F11 | F12 |    DEL    |
 |-----------------------------------------------------------------------------------------+
-|        |RBB T|RGB M| Hue-| Hue+| Sat-| Sat+| Val-| Val+|     |     | MUTE | Prev | Next |
+|        |RBB T|RGB M| Hue-| Hue+| Sat-| Sat+| Val-| Val+| Mute | Vol-| Vol+| Prev | Next |
 |-----------------------------------------------------------------------------------------+
-|         |     |     |     |     |     |     |     |     |    | Vol- | Vol+ | Play/Pause |
+|         |     |     |     |     |     | Left| Down| Up |Right|      |      | Play/Pause |
 |-----------------------------------------------------------------------------------------+
 |           |     |     |     |     |     |     |     |Scr- |Scr+ |         | PG_UP |RESET|
 |-----------------------------------------------------------------------------------------+

keyboards/dz60/keymaps/olligranlund_iso/keymap.c

@@ -26,13 +26,13 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
 		KC_TAB,  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,     KC_I,    KC_O,    KC_P,    KC_LBRC, KC_RBRC,
 		MO(1),   KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,    KC_J,     KC_K,    KC_L,    KC_SCLN, KC_QUOT, KC_BSLS, KC_ENT,
 		KC_LSFT, KC_NUBS, KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,     KC_M,    KC_COMM, KC_DOT,  KC_SLSH, KC_RSFT, KC_PSCR,
-		KC_LCTL, KC_LGUI, KC_LALT, KC_SPC,  KC_SPC,  KC_SPC,  KC_RALT, MO(1),    KC_NO,   KC_APP,   KC_RCTL),
+		KC_LCTL, KC_LGUI, KC_LALT, KC_SPC,  KC_SPC,  KC_SPC,  KC_RALT, MO(1),    KC_APP,  KC_RCTL),
 
 	LAYOUT_60_iso_split_space_bs_rshift(
 		KC_GRV,  KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,    KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,  KC_DEL,  KC_DEL,
 		KC_NO,   KC_MPRV, KC_MPLY, KC_MNXT, KC_NO,   KC_NO,   KC_NO,   KC_PGDOWN,KC_UP,   KC_PGUP, KC_NO,   KC_NO,   KC_NO,
 		KC_NO,   KC_VOLD, KC_MUTE, KC_VOLU, KC_NO,   KC_NO,   KC_HOME,  KC_LEFT, KC_DOWN, KC_RGHT, KC_NO,   KC_NO,   KC_NO,   KC_NO,
 		KC_LSFT, KC_NO,   KC_NO,   KC_NO,   KC_NO,   KC_NO,   KC_NO,   KC_END,   KC_NO,   KC_NO,   KC_NO,   KC_NO,   KC_RSFT, KC_CAPS,
-		KC_LCTL, KC_LGUI, KC_LALT, KC_SPC,  KC_SPC,  KC_SPC,  KC_RALT, MO(1),    KC_NO,   KC_APP,  KC_RCTL),
+		KC_LCTL, KC_LGUI, KC_LALT, KC_SPC,  KC_SPC,  KC_SPC,  KC_RALT, MO(1),    KC_APP,  KC_RCTL),
 
 };

keyboards/ergodox_ez/info.json

@@ -1,7 +1,7 @@
 {
     "keyboard_name": "ErgoDox EZ",
     "url": "ergodox-ez.com",
-    "maintainer": "erez",
+    "maintainer": "ZSA",
     "width": 17,
     "height": 8,
 

keyboards/ergodox_ez/keymaps/pvinis/keymap.c

@@ -0,0 +1,330 @@
+// pvinis ergodox ez
+// ,------------------------------------.          ,------------------------------------.
+// |      |    |    |    |    |    |    |          |    |    |    |    |    |    |      |
+// |------+----+----+----+----+---------|          |----+----+----+----+----+----+------|
+// |      |    |    |    |    |    |    |          |    |    |    |    |    |    |      |
+// |------+----+----+----x----x----|    |          |    |----x----x----+----+----+------|
+// |      |    |    |    |    |    |----|          |----|    |    |    |    |    |      |
+// |------+----+----+----x----x----|    |          |    |----x----x----+----+----+------|
+// |      |    |    |    |    |    |    |          |    |    |    |    |    |    |      |
+// `------+----+----+----+----+---------'          `---------+----+----+----+----+------'
+//   |    |    |    |    |    |                              |    |    |    |    |    |
+//   `------------------------'                              `------------------------'
+//                              ,---------.      ,---------.
+//                              |    |    |      |    |    |
+//                         ,----+----+----|      |----+----+----.
+//                         |    |    |    |      |    |    |    |
+//                         |    |    |----|      |----|    |    |
+//                         |    |    |    |      |    |    |    |
+//                         `--------------'      `--------------'
+
+
+#include QMK_KEYBOARD_H
+#include "pvinis.h"
+#include "mousekey.h"
+
+
+// layers
+enum {
+  MOUSE = 8,
+};
+
+// extra keys
+enum {
+  NONE = 30,
+  TD_LAYR, // SYSCTL and MOUSE layer switch
+};
+
+// application selection
+// this is sending ctrl-alt-gui-<key>, and this is picked up by hammerspoon
+#define AP_SLCK ALLM(KC_S)
+#define AP_XCOD ALLM(KC_X)
+#define AP_MSGR ALLM(KC_M)
+
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+  // ,------------------------------------.          ,------------------------------------.
+  // |4xFLSH|    |    |    |    |    |Opt |          |    |    |    |    |    |    |      |
+  // |------+----+----+----+----+---------|          |----+----+----+----+----+----+------|
+  // | Tab  |    |    |    |    |    |    |          |    |    |    |    |    |    |      |
+  // |------+----+----+----x----x----|    |          |    |----x----x----+----+----+------|
+  // |EscCtl|    |    |    |    |    |----|          |----|    |    |    |    |    | Ent  |
+  // |------+----+----+----x----x----|    |          |    |----x----x----+----+----+------|
+  // |LShift|    |    |    |    |    |    |          |    |    |    |    |    |    |RShift|
+  // `------+----+----+----+----+---------'          `---------+----+----+----+----+------'
+  //   |    |    |    |    |Cmd |                              |    |    |    |    |    |
+  //   `------------------------'                              `------------------------'
+  //                              ,---------.      ,---------.
+  //                              |QWER|    |      |    |    |
+  //                         ,----+----+----|      |----+----+----.
+  //                         | Ba | L  |    |      |    |    |    |
+  //                         | ck |Shi |----|      |----|    |Spc |
+  //                         | spc| ft |    |      |    |    |    |
+  //                         `--------------'      `--------------'
+  [LR_BASE] = LAYOUT_ergodox_pretty_wrapper(
+    TD_3FLS, _______, _______, _______, _______, _______, KC_LALT,      _______, _______, _______, _______, _______, _______, _______,
+    KC_TAB , _______, _______, _______, _______, _______, _______,      _______, _______, _______, _______, _______, _______, _______,
+    PV_ESCC, _______, _______, _______, _______, _______,                        _______, _______, _______, _______, _______, KC_ENT ,
+    KC_LSFT, _______, _______, _______, _______, _______, _______,      _______, _______, _______, _______, _______, _______, KC_RSFT,
+    _______, _______, _______, KC_LGUI, SYMBOL ,                                          SYSCTL , KC_RALT, _______, _______, _______,
+                                                 QWERTY , CARPALX,      _______, _______,
+                                                          _______,      _______,
+                                        KC_BSPC, _______, _______,      _______, _______, KC_SPC
+  ),
+
+  // ,------------------------------------.          ,------------------------------------.
+  // |      |        NUMBERS_L       |    |          |  - |        NUMBERS_R       |  =   |
+  // |------+----+----+----+----+---------|          |----+----+----+----+----+----+------|
+  // |      |                        |  [ |          | ]  |                        |      |
+  // |------+                        |    |          |    |                        +------|
+  // |      |         QWERTY_L       |----|          |----|         QWERTY_R       |      |
+  // |------+                        |  ( |          | )  |                        +------|
+  // |      |                        |    |          |    |                        |      |
+  // `------+----+----+----+----+---------'          `---------+----+----+----+----+------'
+  //   |    | `  |    |    |    |                              |    |    |    |  ' |    |
+  //   `------------------------'                              `------------------------'
+  //                              ,---------.      ,---------.
+  //                              |    |    |      |    |    |
+  //                         ,----+----+----|      |----+----+----.
+  //                         |    |    |    |      |    |    |    |
+  //                         |    |    |----|      |----|    |    |
+  //                         |    |    |    |      |    |    |    |
+  //                         `--------------'      `--------------'
+  // See `users/pvinis/pvinis.h`
+  [LR_QWERTY] = LAYOUT_ergodox_pretty_wrapper(
+    _______, ________________NUMBERS_L__________________, _______,      KC_MINS, ________________NUMBERS_R__________________, KC_EQL ,
+    _______, _________________QWERTY_L1_________________, KC_LBRC,      KC_RBRC, _________________QWERTY_R1_________________, _______,
+    _______, _________________QWERTY_L2_________________,                        _________________QWERTY_R2_________________, _______,
+    _______, _________________QWERTY_L3_________________, KC_LPRN,      KC_RPRN, _________________QWERTY_R3_________________, _______,
+    _______, KC_GRV, _______, _______, _______,                                          _______, _______, _______, KC_QUOT , _______,
+                                                 _______, _______,      _______, _______,
+                                                          _______,      _______,
+                                        _______, _______, _______,      _______, _______, _______
+  ),
+
+  // ,------------------------------------.          ,------------------------------------.
+  // |      |        NUMBERS_L       |    |          |    |        NUMBERS_R       |      |
+  // |------+----+----+----+----+---------|          |----+----+----+----+----+----+------|
+  // |      |                        |    |          |    |                        |      |
+  // |------+                        |    |          |    |                        +------|
+  // |      |        CARPALX_L       |----|          |----|        CARPALX_R       |      |
+  // |------+                        |    |          |    |                        +------|
+  // |      |                        |    |          |    |                        |      |
+  // `------+----+----+----+----+---------'          `---------+----+----+----+----+------'
+  //   |    |    |    |    |    |                              |    |    |    |    |    |
+  //   `------------------------'                              `------------------------'
+  //                              ,---------.      ,---------.
+  //                              |    |    |      |    |    |
+  //                         ,----+----+----|      |----+----+----.
+  //                         |    |    |    |      |    |    |    |
+  //                         |    |    |----|      |----|    |    |
+  //                         |    |    |    |      |    |    |    |
+  //                         `--------------'      `--------------'
+  // See `users/pvinis/pvinis.h`
+  [LR_CARPALX] = LAYOUT_ergodox_pretty_wrapper(
+    _______, ________________NUMBERS_L__________________, _______,      _______, ________________NUMBERS_R__________________, _______,
+    _______, ________________CARPALX_L1_________________, _______,      _______, ________________CARPALX_R1_________________, _______,
+    _______, ________________CARPALX_L2_________________,                        ________________CARPALX_R2_________________, _______,
+    _______, ________________CARPALX_L3_________________, _______,      _______, ________________CARPALX_R3_________________, _______,
+    _______, _______, _______, _______, _______,                                          _______, _______, _______, _______, _______,
+                                                 _______, _______,      _______, _______,
+                                                          _______,      _______,
+                                        _______, _______, _______,      _______, _______, _______
+  ),
+
+  // See `users/pvinis/pvinis.h`
+  [LR_SYMBOL] = LAYOUT_ergodox_pretty_wrapper(
+    _______, ______________________F_L__________________, KC_F11 ,      KC_F12 , ______________________F_R__________________, _______,
+    _______, _________________SYMBOL_L1_________________, _______,      _______, _________________SYMBOL_R1_________________, _______,
+    _______, _________________SYMBOL_L2_________________,                        _________________SYMBOL_R2_________________, _______,
+    _______, _________________SYMBOL_L3_________________, _______,      _______, _________________SYMBOL_R3_________________, _______,
+    _______, _______, _______, _______, _______,                                          _______, _______, _______, _______, _______,
+                                                 _______, _______,      _______, _______,
+                                                          _______,      _______,
+                                        _______, _______, _______,      _______, _______, _______
+  ),
+
+  // See `users/pvinis/pvinis.h`
+  [LR_SYSCTL] = LAYOUT_ergodox_pretty_wrapper(
+    _______, _______, _______, _______, _______, _______, _______,      _______, _______, _______, _______, _______, _______, _______,
+    _______, _______, _______, _______, _______, _______, _______,      _______, _________________SYSCTL_R1_________________, _______,
+    _______, _______, _______, _______, _______, _______,                        _________________SYSCTL_R2_________________, _______,
+    _______, _______, _______, _______, _______, _______, _______,      _______, _________________SYSCTL_R3_________________, _______,
+    _______, _______, _______, _______, _______,                                          _______, _______, _______, _______, _______,
+
+                                                 _______, _______,      _______, _______,
+                                                          _______,      _______,
+                                        _______, _______, _______,      _______, _______, _______
+  ),
+
+  // See `users/pvinis/pvinis.h`
+  [LR_KBCTL] = LAYOUT_ergodox_pretty_wrapper(
+    XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX,      XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX,
+    XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX,      XXXXXXX, __________________KBCTL_R1_________________, XXXXXXX,
+    XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX,                        __________________KBCTL_R2_________________, XXXXXXX,
+    XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX,      XXXXXXX, __________________KBCTL_R3_________________, XXXXXXX,
+    XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, _______,                                          _______, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX,
+
+                                                 XXXXXXX, XXXXXXX,      XXXXXXX, XXXXXXX,
+                                                          XXXXXXX,      XXXXXXX,
+                                        XXXXXXX, XXXXXXX, XXXXXXX,      XXXXXXX, XXXXXXX, XXXXXXX
+  ),
+
+/* MOUSE
+ * a keymap to control my system.
+ *
+ * ,--------------------------------------------------.           ,--------------------------------------------------.
+ * |   ^    |      |      |      |      |      |      |           |      |      |      |      |      |      |        |
+ * |--------+------+------+------+------+-------------|           |------+------+------+------+------+------+--------|
+ * |        |      |      |      |      |      |      |           |      |      |      | MsUp |      |      |        |
+ * |--------+------+------+------+------+------|      |           |      |------+------+------+------+------+--------|
+ * |        |      |      |      |      |      |------|           |------|      |MsLeft| MsDn |MsRght|      |        |
+ * |--------+------+------+------+------+------|      |           |      |------+------+------+------+------+--------|
+ * |        |      |      |      |      |      |      |           |      |      |      |      |      |      |        |
+ * `--------+------+------+------+------+-------------'           `-------------+------+------+------+------+--------'
+ *   |      |      |      |      |      |                                       |      |      |      |      |      |
+ *   `----------------------------------'                                       `----------------------------------'
+ *                                        ,-------------.       ,-------------.
+ *                                        |      |      |       |      |MidClk|
+ *                                 ,------|------|------|       |------+------+------.
+ *                                 |      |      |      |       |      |Left  |Right |
+ *                                 |      |      |------|       |------| Click| Click|
+ *                                 |      |      |  ^   |       |      |      |      |
+ *                                 `--------------------'       `--------------------'
+ */
+  [MOUSE] = LAYOUT_ergodox_pretty(
+   KC_TRNS    ,KC_NO  ,KC_NO  ,KC_NO  ,KC_NO  ,KC_NO    ,KC_NO
+  ,KC_NO      ,KC_NO  ,KC_NO  ,KC_NO  ,KC_NO  ,KC_NO    ,KC_NO
+  ,KC_NO      ,KC_NO  ,KC_NO  ,KC_NO  ,KC_NO  ,KC_NO
+  ,KC_NO      ,KC_NO  ,KC_NO  ,KC_NO  ,KC_NO  ,KC_NO    ,KC_NO
+  ,KC_NO      ,KC_NO  ,KC_NO  ,KC_NO  ,KC_NO
+
+                                                        ,KC_NO  ,KC_NO
+                                                                ,KC_NO
+                                                ,KC_NO  ,KC_NO  ,KC_TRNS
+
+                    ,KC_NO    ,KC_NO  ,KC_NO    ,KC_NO    ,KC_NO    ,KC_NO    ,KC_NO
+                    ,KC_NO    ,KC_NO  ,KC_NO    ,KC_MS_U  ,KC_NO    ,KC_NO    ,KC_NO
+                              ,KC_NO  ,KC_MS_L  ,KC_MS_D  ,KC_MS_R  ,KC_NO    ,KC_NO
+                    ,KC_NO    ,KC_NO  ,KC_NO    ,KC_NO    ,KC_NO    ,KC_NO    ,KC_NO
+                                      ,KC_NO    ,KC_NO    ,KC_NO    ,KC_NO    ,KC_NO
+
+            ,KC_NO  ,KC_NO
+            ,KC_NO
+            ,KC_NO  ,KC_NO  ,KC_NO
+  ),
+};
+
+
+// keyboard initialization
+void keyboard_post_init_user_local(void) {
+  ergodox_led_all_on();
+  for (int i = LED_BRIGHTNESS_HI; i > LED_BRIGHTNESS_LO; i--) {
+    ergodox_led_all_set(i);
+    wait_ms(5);
+  }
+  wait_ms(1000);
+  for (int i = LED_BRIGHTNESS_LO; i > 0; i--) {
+    ergodox_led_all_set(i);
+    wait_ms(10);
+  }
+  ergodox_led_all_off();
+
+  // restore default brightness for future use
+  ergodox_led_all_set(LED_BRIGHTNESS_HI);
+}
+
+// light up leds based on the layer
+uint32_t layer_state_set_user_local(uint32_t state) {
+  ergodox_right_led_1_off();
+  ergodox_right_led_2_off();
+  ergodox_right_led_3_off();
+  switch (biton32(state)) {
+  case LR_SYSCTL:
+    ergodox_right_led_3_on(); // blue
+    break;
+  case LR_KBCTL:
+    ergodox_right_led_1_on(); // red
+    break;
+  case LR_SYMBOL:
+    ergodox_right_led_2_on(); // green
+    break;
+  default: break;
+  }
+  return state;
+}
+
+// extra keys
+// const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) {
+  // switch (id) {
+  // }
+  // return MACRO_NONE;
+// }
+
+// tap dances
+
+// flash keyboard on 4x tap, with leds
+// void flash_each_tap(qk_tap_dance_state_t *state, void *user_data) {
+//   switch (state->count) {
+//   case 1:
+//     ergodox_right_led_3_on();
+//     break;
+//   case 2:
+//     ergodox_right_led_2_on();
+//     break;
+//   case 3:
+//     ergodox_right_led_1_on();
+//     break;
+//   case 4:
+//     ergodox_right_led_3_off();
+//     wait_ms(50);
+//     ergodox_right_led_2_off();
+//     wait_ms(50);
+//     ergodox_right_led_1_off();
+//     break;
+//   }
+// }
+
+// void flash_dance_finished(qk_tap_dance_state_t *state, void *user_data) {
+//   if (state->count >= 4) {
+//     reset_keyboard();
+//     reset_tap_dance(state);
+//   }
+// }
+
+// void flash_dance_reset(qk_tap_dance_state_t *state, void *user_data) {
+//   ergodox_right_led_1_off();
+//   wait_ms(50);
+//   ergodox_right_led_2_off();
+//   wait_ms(50);
+//   ergodox_right_led_3_off();
+// }
+
+// SYSCTL on first tap, MOUSE ON second tap
+// void layers_dance_finished(qk_tap_dance_state_t *state, void *user_data) {
+//   uint8_t layer = biton32(layer_state);
+
+//   switch(state->count) {
+//   case 1:
+//     switch(layer) {
+//     case LR_SYSCTL:
+//       layer_off(LR_SYSCTL);
+//       break;
+//     case MOUSE:
+//       layer_off(MOUSE);
+//       break;
+//     default:
+//       layer_on(LR_SYSCTL);
+//       break;
+//     }
+//     break;
+//   case 2:
+//     layer_on(MOUSE);
+//     break;
+//   }
+// }
+
+// qk_tap_dance_action_t tap_dance_actions[] = {
+  // [TD_FLSH] = ACTION_TAP_DANCE_FN_ADVANCED( flash_each_tap, flash_dance_finished, flash_dance_reset ),
+  // [TD_LAYR] = ACTION_TAP_DANCE_FN_ADVANCED( NULL, layers_dance_finished, NULL ),
+// };

keyboards/ergodox_ez/keymaps/pvinis/rules.mk

@@ -0,0 +1 @@
+TAP_DANCE_ENABLE = yes

keyboards/ergodox_ez/matrix.c

@@ -1,9 +1,5 @@
 /*
 
-Note for ErgoDox EZ customizers: Here be dragons!
-This is not a file you want to be messing with.
-All of the interesting stuff for you is under keymaps/ :)
-Love, Erez
 
 Copyright 2013 Oleg Kostyuk <cub.uanic@gmail.com>
 
@@ -95,7 +91,7 @@ void matrix_init(void) {
   // initialize matrix state: all keys off
   for (uint8_t i = 0; i < MATRIX_ROWS; i++) {
     matrix[i]     = 0;
-    raw_matrix[i] = 0;    
+    raw_matrix[i] = 0;
   }
 
 #ifdef DEBUG_MATRIX_SCAN_RATE
@@ -168,7 +164,7 @@ uint8_t matrix_scan(void) {
 #ifdef LEFT_LEDS
   mcp23018_status = ergodox_left_leds_update();
 #endif  // LEFT_LEDS
-  bool changed = false;  
+  bool changed = false;
   for (uint8_t i = 0; i < MATRIX_ROWS_PER_SIDE; i++) {
     // select rows from left and right hands
     uint8_t left_index = i;
@@ -178,13 +174,13 @@ uint8_t matrix_scan(void) {
 
     // we don't need a 30us delay anymore, because selecting a
     // left-hand row requires more than 30us for i2c.
-    
+
     changed |= store_raw_matrix_row(left_index);
     changed |= store_raw_matrix_row(right_index);
 
     unselect_rows();
   }
-  
+
   debounce(raw_matrix, matrix, MATRIX_ROWS, changed);
   matrix_scan_quantum();
 

keyboards/ergotaco/matrix.c

@@ -1,8 +1,4 @@
 /*
-Note for ErgoDox EZ customizers: Here be dragons!
-This is not a file you want to be messing with.
-All of the interesting stuff for you is under keymaps/ :)
-Love, Erez
 
 Copyright 2013 Oleg Kostyuk <cub.uanic@gmail.com>
 
@@ -226,8 +222,8 @@ uint8_t matrix_scan(void)
     matrix_scan_quantum();
 
 #ifdef DEBUG_MATRIX
-    for (uint8_t c = 0; c < MATRIX_COLS; c++) 
-		for (uint8_t r = 0; r < MATRIX_ROWS; r++) 
+    for (uint8_t c = 0; c < MATRIX_COLS; c++)
+		for (uint8_t r = 0; r < MATRIX_ROWS; r++)
 		  if (matrix_is_on(r, c)) xprintf("r:%d c:%d \n", r, c);
 #endif
 
@@ -324,10 +320,10 @@ static void unselect_rows(void)
 static void select_row(uint8_t row)
 {
     if (row < 6) {
-        // select on mcp23018 
+        // select on mcp23018
         if (mcp23018_status) { // do nothing on error
 			// Read using bitmask
-        } else { // set active row low  : 0 // set other rows hi-Z : 1 
+        } else { // set active row low  : 0 // set other rows hi-Z : 1
             mcp23018_status = i2c_start(I2C_ADDR_WRITE, ERGODOX_EZ_I2C_TIMEOUT);        if (mcp23018_status) goto out;
             mcp23018_status = i2c_write(GPIOA, ERGODOX_EZ_I2C_TIMEOUT);                 if (mcp23018_status) goto out;
             mcp23018_status = i2c_write(~(1<<row), ERGODOX_EZ_I2C_TIMEOUT);      		if (mcp23018_status) goto out;

keyboards/foxlab/leaf60/hotswap/config.h

@@ -0,0 +1,229 @@
+/*
+Copyright 2019 Fox Lab
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0xFEED
+#define PRODUCT_ID      0x0000
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    Fox Lab
+#define PRODUCT         Leaf60 Hotswap
+#define DESCRIPTION     A custom hotswap 60% keyboard
+
+/* key matrix size */
+#define MATRIX_ROWS 5
+#define MATRIX_COLS 15
+
+/*
+ * Keyboard Matrix Assignments
+ *
+ * Change this to how you wired your keyboard
+ * COLS: AVR pins used for columns, left to right
+ * ROWS: AVR pins used for rows, top to bottom
+ * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
+ *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
+ *
+*/
+#define MATRIX_ROW_PINS { D2, D1, D0, D3, D5 }
+#define MATRIX_COL_PINS { F5, F4, F1, F0, B0, F6, F7, C7, C6, B6, B5, B4, D7, D6, D4 }
+#define UNUSED_PINS
+
+/* COL2ROW, ROW2COL*/
+#define DIODE_DIRECTION COL2ROW
+
+#define BACKLIGHT_PIN B7
+#define BACKLIGHT_BREATHING
+#define BACKLIGHT_LEVELS 4
+
+#define RGB_DI_PIN E2
+#ifdef RGB_DI_PIN
+  #define RGBLED_NUM 8
+  #define RGBLIGHT_HUE_STEP 8
+  #define RGBLIGHT_SAT_STEP 8
+  #define RGBLIGHT_VAL_STEP 8
+  #define RGBLIGHT_SLEEP  /* If defined, the RGB lighting will be switched off when the host goes to sleep */
+/*== all animations enable ==*/
+  #define RGBLIGHT_ANIMATIONS
+#endif
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCING_DELAY 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/* If defined, GRAVE_ESC will always act as ESC when CTRL is held.
+ * This is userful for the Windows task manager shortcut (ctrl+shift+esc).
+ */
+// #define GRAVE_ESC_CTRL_OVERRIDE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/* key combination for magic key command */
+/* defined by default; to change, uncomment and set to the combination you want */
+// #define IS_COMMAND() (get_mods() == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)))
+
+/* control how magic key switches layers */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
+
+/* override magic key keymap */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
+//#define MAGIC_KEY_HELP           H
+//#define MAGIC_KEY_HELP_ALT       SLASH
+//#define MAGIC_KEY_DEBUG          D
+//#define MAGIC_KEY_DEBUG_MATRIX   X
+//#define MAGIC_KEY_DEBUG_KBD      K
+//#define MAGIC_KEY_DEBUG_MOUSE    M
+//#define MAGIC_KEY_VERSION        V
+//#define MAGIC_KEY_STATUS         S
+//#define MAGIC_KEY_CONSOLE        C
+//#define MAGIC_KEY_LAYER0         0
+//#define MAGIC_KEY_LAYER0_ALT     GRAVE
+//#define MAGIC_KEY_LAYER1         1
+//#define MAGIC_KEY_LAYER2         2
+//#define MAGIC_KEY_LAYER3         3
+//#define MAGIC_KEY_LAYER4         4
+//#define MAGIC_KEY_LAYER5         5
+//#define MAGIC_KEY_LAYER6         6
+//#define MAGIC_KEY_LAYER7         7
+//#define MAGIC_KEY_LAYER8         8
+//#define MAGIC_KEY_LAYER9         9
+//#define MAGIC_KEY_BOOTLOADER     B
+//#define MAGIC_KEY_BOOTLOADER_ALT ESC
+//#define MAGIC_KEY_LOCK           CAPS
+//#define MAGIC_KEY_EEPROM         E
+//#define MAGIC_KEY_EEPROM_CLEAR   BSPACE
+//#define MAGIC_KEY_NKRO           N
+//#define MAGIC_KEY_SLEEP_LED      Z
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+/*
+ * MIDI options
+ */
+
+/* Prevent use of disabled MIDI features in the keymap */
+//#define MIDI_ENABLE_STRICT 1
+
+/* enable basic MIDI features:
+   - MIDI notes can be sent when in Music mode is on
+*/
+//#define MIDI_BASIC
+
+/* enable advanced MIDI features:
+   - MIDI notes can be added to the keymap
+   - Octave shift and transpose
+   - Virtual sustain, portamento, and modulation wheel
+   - etc.
+*/
+//#define MIDI_ADVANCED
+
+/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
+//#define MIDI_TONE_KEYCODE_OCTAVES 1
+
+/*
+ * HD44780 LCD Display Configuration
+ */
+/*
+#define LCD_LINES           2     //< number of visible lines of the display
+#define LCD_DISP_LENGTH    16     //< visibles characters per line of the display
+
+#define LCD_IO_MODE      1            //< 0: memory mapped mode, 1: IO port mode
+
+#if LCD_IO_MODE
+#define LCD_PORT         PORTB        //< port for the LCD lines
+#define LCD_DATA0_PORT   LCD_PORT     //< port for 4bit data bit 0
+#define LCD_DATA1_PORT   LCD_PORT     //< port for 4bit data bit 1
+#define LCD_DATA2_PORT   LCD_PORT     //< port for 4bit data bit 2
+#define LCD_DATA3_PORT   LCD_PORT     //< port for 4bit data bit 3
+#define LCD_DATA0_PIN    4            //< pin for 4bit data bit 0
+#define LCD_DATA1_PIN    5            //< pin for 4bit data bit 1
+#define LCD_DATA2_PIN    6            //< pin for 4bit data bit 2
+#define LCD_DATA3_PIN    7            //< pin for 4bit data bit 3
+#define LCD_RS_PORT      LCD_PORT     //< port for RS line
+#define LCD_RS_PIN       3            //< pin  for RS line
+#define LCD_RW_PORT      LCD_PORT     //< port for RW line
+#define LCD_RW_PIN       2            //< pin  for RW line
+#define LCD_E_PORT       LCD_PORT     //< port for Enable line
+#define LCD_E_PIN        1            //< pin  for Enable line
+#endif
+*/
+
+/* Bootmagic Lite key configuration */
+// #define BOOTMAGIC_LITE_ROW 0
+// #define BOOTMAGIC_LITE_COLUMN 0

keyboards/foxlab/leaf60/hotswap/hotswap.c

@@ -0,0 +1,59 @@
+/* Copyright 2019 Fox Lab
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include "hotswap.h"
+
+// Optional override functions below.
+// You can leave any or all of these undefined.
+// These are only required if you want to perform custom actions.
+
+void matrix_init_kb(void) {
+  // put your keyboard start-up code here
+  // runs once when the firmware starts up
+  setPinOutput(E6);
+  matrix_init_user();
+}
+/*
+
+void matrix_scan_kb(void) {
+  // put your looping keyboard code here
+  // runs every cycle (a lot)
+
+  matrix_scan_user();
+}
+
+bool process_record_kb(uint16_t keycode, keyrecord_t *record) {
+  // put your per-action keyboard code here
+  // runs for every action, just before processing by the firmware
+
+  return process_record_user(keycode, record);
+}
+
+void led_set_kb(uint8_t usb_led) {
+  // put your keyboard LED indicator (ex: Caps Lock LED) toggling code here
+
+  led_set_user(usb_led);
+}
+
+*/
+
+void led_set_kb(uint8_t usb_led) {
+  if (IS_LED_ON(usb_led, USB_LED_CAPS_LOCK)) {
+    writePinLow(E6);
+  } else {
+    writePinHigh(E6);
+  }
+	led_set_user(usb_led);
+}

keyboards/foxlab/leaf60/hotswap/hotswap.h

@@ -0,0 +1,40 @@
+/* Copyright 2019 Fox Lab
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#pragma once
+
+#include "quantum.h"
+
+/* This a shortcut to help you visually see your layout.
+ *
+ * The first section contains all of the arguments representing the physical
+ * layout of the board and position of the keys.
+ *
+ * The second converts the arguments into a two-dimensional array which
+ * represents the switch matrix.
+ */
+#define LAYOUT_60_tsangan_hhkb( \
+	K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014, \
+	K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113,       \
+	K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212,             \
+	K300,       K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312, K313,       \
+	K400, K401, K402,                         K407,                   K411, K412, K413  \
+) { \
+	{ K000,  K001,  K002,  K003,  K004,  K005,  K006,  K007,  K008,  K009,  K010,  K011,  K012,  K013,  K014 }, \
+	{ K100,  K101,  K102,  K103,  K104,  K105,  K106,  K107,  K108,  K109,  K110,  K111,  K112,  K113,  KC_NO }, \
+	{ K200,  K201,  K202,  K203,  K204,  K205,  K206,  K207,  K208,  K209,  K210,  K211,  K212,  KC_NO, KC_NO }, \
+	{ K300,  KC_NO, K302,  K303,  K304,  K305,  K306,  K307,  K308,  K309,  K310,  K311,  K312,  K313,  KC_NO }, \
+	{ K400,  K401,  K402,  KC_NO, KC_NO, KC_NO, KC_NO, K407,  KC_NO, KC_NO, KC_NO, K411,  K412,  K413,  KC_NO }  \
+}

keyboards/foxlab/leaf60/hotswap/info.json

@@ -0,0 +1,12 @@
+{
+    "keyboard_name": "Fox Lab Hotswap Leaf60", 
+    "url": "", 
+    "maintainer": "qmk", 
+    "width": 15, 
+    "height": 5, 
+    "layouts": {
+        "LAYOUT_60_tsangan_hhkb": {
+            "layout": [{"x":0, "y":0}, {"x":1, "y":0}, {"x":2, "y":0}, {"x":3, "y":0}, {"x":4, "y":0}, {"x":5, "y":0}, {"x":6, "y":0}, {"x":7, "y":0}, {"x":8, "y":0}, {"x":9, "y":0}, {"x":10, "y":0}, {"x":11, "y":0}, {"x":12, "y":0}, {"x":13, "y":0}, {"x":14, "y":0}, {"x":0, "y":1, "w":1.5}, {"x":1.5, "y":1}, {"x":2.5, "y":1}, {"x":3.5, "y":1}, {"x":4.5, "y":1}, {"x":5.5, "y":1}, {"x":6.5, "y":1}, {"x":7.5, "y":1}, {"x":8.5, "y":1}, {"x":9.5, "y":1}, {"x":10.5, "y":1}, {"x":11.5, "y":1}, {"x":12.5, "y":1}, {"x":13.5, "y":1, "w":1.5}, {"x":0, "y":2, "w":1.75}, {"x":1.75, "y":2}, {"x":2.75, "y":2}, {"x":3.75, "y":2}, {"x":4.75, "y":2}, {"x":5.75, "y":2}, {"x":6.75, "y":2}, {"x":7.75, "y":2}, {"x":8.75, "y":2}, {"x":9.75, "y":2}, {"x":10.75, "y":2}, {"x":11.75, "y":2}, {"x":12.75, "y":2, "w":2.25}, {"x":0, "y":3, "w":2.25}, {"x":2.25, "y":3}, {"x":3.25, "y":3}, {"x":4.25, "y":3}, {"x":5.25, "y":3}, {"x":6.25, "y":3}, {"x":7.25, "y":3}, {"x":8.25, "y":3}, {"x":9.25, "y":3}, {"x":10.25, "y":3}, {"x":11.25, "y":3}, {"x":12.25, "y":3, "w":1.75}, {"x":14, "y":3}, {"x":0, "y":4, "w":1.5}, {"x":1.5, "y":4}, {"x":2.5, "y":4, "w":1.5}, {"x":4, "y":4, "w":7}, {"x":11, "y":4, "w":1.5}, {"x":12.5, "y":4}, {"x":13.5, "y":4, "w":1.5}]
+        }
+    }
+}

keyboards/foxlab/leaf60/hotswap/keymaps/default/config.h

@@ -0,0 +1,19 @@
+/* Copyright 2019 MechMerlin
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+
+// place overrides here

keyboards/foxlab/leaf60/hotswap/keymaps/default/keymap.c

@@ -0,0 +1,46 @@
+/* Copyright 2019 Fox Lab
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include QMK_KEYBOARD_H
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+	LAYOUT_60_tsangan_hhkb(
+		KC_ESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL,  KC_GRV, KC_BSLS,
+		KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSPC, 
+		KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_ENT, 
+		KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT, KC_DEL, 
+		KC_LCTL, KC_LGUI, KC_LALT, KC_SPC, MO(1), KC_RALT, KC_RCTL),
+
+	LAYOUT_60_tsangan_hhkb(
+		RESET, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_TRNS, KC_TRNS, 
+		KC_TRNS, BL_TOGG, BL_DEC, BL_INC, BL_STEP, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, 
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, 
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, 
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS)
+
+};
+
+void matrix_init_user(void) {
+
+}
+
+void matrix_scan_user(void) {
+
+}
+
+void led_set_user(uint8_t usb_led) {
+
+}

keyboards/foxlab/leaf60/hotswap/keymaps/default/readme.md

@@ -0,0 +1 @@
+# The default keymap for Fox Lab Hotswap Leaf60

keyboards/foxlab/leaf60/hotswap/readme.md

@@ -0,0 +1,13 @@
+# Fox Lab Hotswap Leaf60 
+
+A hotswap, Tsangan-layout, gasket-mount 60% keyboard.
+
+Keyboard Maintainer: [Fox Lab](https://github.com/fox-lab), [MechMerlin](https://github.com/mechmerlin)  
+Hardware Supported: Leaf60 powered by the ATmega32U4  
+Hardware Availability: [Geekhack Group Buy](https://geekhack.org/index.php?topic=99002.0)  
+
+Make example for this keyboard (after setting up your build environment):
+
+    make foxlab/leaf60/hotswap:default
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/foxlab/leaf60/hotswap/rules.mk

@@ -0,0 +1,80 @@
+# MCU name
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   atmega32a    bootloadHID
+BOOTLOADER = atmel-dfu
+
+
+# If you don't know the bootloader type, then you can specify the
+# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
+#   Teensy halfKay      512
+#   Teensy++ halfKay    1024
+#   Atmel DFU loader    4096
+#   LUFA bootloader     4096
+#   USBaspLoader        2048
+# OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE = yes      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = no        # Console for debug(+400)
+COMMAND_ENABLE = no        # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE = no            # USB Nkey Rollover
+BACKLIGHT_ENABLE = yes       # Enable keyboard backlight functionality on B7 by default
+RGBLIGHT_ENABLE = yes        # Enable keyboard RGB underglow
+MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no           # Audio output on port C6
+FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
+HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)

keyboards/foxlab/leaf60/readme.md

@@ -0,0 +1,7 @@
+# Fox Lab Leaf60
+
+The Leaf60 is a 60% gasket mount board sold via [Geekhack Group Buy](https://geekhack.org/index.php?topic=99002.0).
+
+It was available with a universal layout PCB and a hotswap tsangan PCB. 
+
+**Firmware generated for one PCB will not work on the other.**

keyboards/foxlab/leaf60/universal/config.h

@@ -0,0 +1,229 @@
+/*
+Copyright 2019 Fox Lab
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0xFEED
+#define PRODUCT_ID      0x0000
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    Fox Lab
+#define PRODUCT         Leaf60 Universal
+#define DESCRIPTION     A custom 60% keyboard
+
+/* key matrix size */
+#define MATRIX_ROWS 5
+#define MATRIX_COLS 15
+
+/*
+ * Keyboard Matrix Assignments
+ *
+ * Change this to how you wired your keyboard
+ * COLS: AVR pins used for columns, left to right
+ * ROWS: AVR pins used for rows, top to bottom
+ * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
+ *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
+ *
+*/
+#define MATRIX_ROW_PINS { D0, D1, F0, F4, F1 }
+#define MATRIX_COL_PINS { B0, F5, F6, F7, C7, C6, B6, B5, B4, D7, D6, D4, D5, D3, D2 }
+#define UNUSED_PINS
+
+/* COL2ROW, ROW2COL*/
+#define DIODE_DIRECTION COL2ROW
+
+#define BACKLIGHT_PIN B7
+#define BACKLIGHT_BREATHING
+#define BACKLIGHT_LEVELS 3
+
+#define RGB_DI_PIN E2
+#ifdef RGB_DI_PIN
+  #define RGBLED_NUM 8
+  #define RGBLIGHT_HUE_STEP 8
+  #define RGBLIGHT_SAT_STEP 8
+  #define RGBLIGHT_VAL_STEP 8
+  #define RGBLIGHT_SLEEP  /* If defined, the RGB lighting will be switched off when the host goes to sleep */
+/*== all animations enable ==*/
+  #define RGBLIGHT_ANIMATIONS
+#endif
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCING_DELAY 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/* If defined, GRAVE_ESC will always act as ESC when CTRL is held.
+ * This is userful for the Windows task manager shortcut (ctrl+shift+esc).
+ */
+// #define GRAVE_ESC_CTRL_OVERRIDE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/* key combination for magic key command */
+/* defined by default; to change, uncomment and set to the combination you want */
+// #define IS_COMMAND() (get_mods() == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)))
+
+/* control how magic key switches layers */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
+
+/* override magic key keymap */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
+//#define MAGIC_KEY_HELP           H
+//#define MAGIC_KEY_HELP_ALT       SLASH
+//#define MAGIC_KEY_DEBUG          D
+//#define MAGIC_KEY_DEBUG_MATRIX   X
+//#define MAGIC_KEY_DEBUG_KBD      K
+//#define MAGIC_KEY_DEBUG_MOUSE    M
+//#define MAGIC_KEY_VERSION        V
+//#define MAGIC_KEY_STATUS         S
+//#define MAGIC_KEY_CONSOLE        C
+//#define MAGIC_KEY_LAYER0         0
+//#define MAGIC_KEY_LAYER0_ALT     GRAVE
+//#define MAGIC_KEY_LAYER1         1
+//#define MAGIC_KEY_LAYER2         2
+//#define MAGIC_KEY_LAYER3         3
+//#define MAGIC_KEY_LAYER4         4
+//#define MAGIC_KEY_LAYER5         5
+//#define MAGIC_KEY_LAYER6         6
+//#define MAGIC_KEY_LAYER7         7
+//#define MAGIC_KEY_LAYER8         8
+//#define MAGIC_KEY_LAYER9         9
+//#define MAGIC_KEY_BOOTLOADER     B
+//#define MAGIC_KEY_BOOTLOADER_ALT ESC
+//#define MAGIC_KEY_LOCK           CAPS
+//#define MAGIC_KEY_EEPROM         E
+//#define MAGIC_KEY_EEPROM_CLEAR   BSPACE
+//#define MAGIC_KEY_NKRO           N
+//#define MAGIC_KEY_SLEEP_LED      Z
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+/*
+ * MIDI options
+ */
+
+/* Prevent use of disabled MIDI features in the keymap */
+//#define MIDI_ENABLE_STRICT 1
+
+/* enable basic MIDI features:
+   - MIDI notes can be sent when in Music mode is on
+*/
+//#define MIDI_BASIC
+
+/* enable advanced MIDI features:
+   - MIDI notes can be added to the keymap
+   - Octave shift and transpose
+   - Virtual sustain, portamento, and modulation wheel
+   - etc.
+*/
+//#define MIDI_ADVANCED
+
+/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
+//#define MIDI_TONE_KEYCODE_OCTAVES 1
+
+/*
+ * HD44780 LCD Display Configuration
+ */
+/*
+#define LCD_LINES           2     //< number of visible lines of the display
+#define LCD_DISP_LENGTH    16     //< visibles characters per line of the display
+
+#define LCD_IO_MODE      1            //< 0: memory mapped mode, 1: IO port mode
+
+#if LCD_IO_MODE
+#define LCD_PORT         PORTB        //< port for the LCD lines
+#define LCD_DATA0_PORT   LCD_PORT     //< port for 4bit data bit 0
+#define LCD_DATA1_PORT   LCD_PORT     //< port for 4bit data bit 1
+#define LCD_DATA2_PORT   LCD_PORT     //< port for 4bit data bit 2
+#define LCD_DATA3_PORT   LCD_PORT     //< port for 4bit data bit 3
+#define LCD_DATA0_PIN    4            //< pin for 4bit data bit 0
+#define LCD_DATA1_PIN    5            //< pin for 4bit data bit 1
+#define LCD_DATA2_PIN    6            //< pin for 4bit data bit 2
+#define LCD_DATA3_PIN    7            //< pin for 4bit data bit 3
+#define LCD_RS_PORT      LCD_PORT     //< port for RS line
+#define LCD_RS_PIN       3            //< pin  for RS line
+#define LCD_RW_PORT      LCD_PORT     //< port for RW line
+#define LCD_RW_PIN       2            //< pin  for RW line
+#define LCD_E_PORT       LCD_PORT     //< port for Enable line
+#define LCD_E_PIN        1            //< pin  for Enable line
+#endif
+*/
+
+/* Bootmagic Lite key configuration */
+// #define BOOTMAGIC_LITE_ROW 0
+// #define BOOTMAGIC_LITE_COLUMN 0

keyboards/foxlab/leaf60/universal/info.json

@@ -0,0 +1,20 @@
+{
+    "keyboard_name": "Fox Lab Leaf60", 
+    "url": "", 
+    "maintainer": "qmk", 
+    "width": 15, 
+    "height": 5, 
+    "layouts": {
+        "LAYOUT_all": {
+            "layout": [{"x":0, "y":0}, {"x":1, "y":0}, {"x":2, "y":0}, {"x":3, "y":0}, {"x":4, "y":0}, {"x":5, "y":0}, {"x":6, "y":0}, {"x":7, "y":0}, {"x":8, "y":0}, {"x":9, "y":0}, {"x":10, "y":0}, {"x":11, "y":0}, {"x":12, "y":0}, {"x":13, "y":0}, {"x":14, "y":0}, {"x":0, "y":1, "w":1.5}, {"x":1.5, "y":1}, {"x":2.5, "y":1}, {"x":3.5, "y":1}, {"x":4.5, "y":1}, {"x":5.5, "y":1}, {"x":6.5, "y":1}, {"x":7.5, "y":1}, {"x":8.5, "y":1}, {"x":9.5, "y":1}, {"x":10.5, "y":1}, {"x":11.5, "y":1}, {"x":12.5, "y":1}, {"x":13.5, "y":1, "w":1.5}, {"x":0, "y":2, "w":1.75}, {"x":1.75, "y":2}, {"x":2.75, "y":2}, {"x":3.75, "y":2}, {"x":4.75, "y":2}, {"x":5.75, "y":2}, {"x":6.75, "y":2}, {"x":7.75, "y":2}, {"x":8.75, "y":2}, {"x":9.75, "y":2}, {"x":10.75, "y":2}, {"x":11.75, "y":2}, {"x":12.75, "y":2, "w":2.25}, {"x":0, "y":3, "w":1.25}, {"x":1.25, "y":3}, {"x":2.25, "y":3}, {"x":3.25, "y":3}, {"x":4.25, "y":3}, {"x":5.25, "y":3}, {"x":6.25, "y":3}, {"x":7.25, "y":3}, {"x":8.25, "y":3}, {"x":9.25, "y":3}, {"x":10.25, "y":3}, {"x":11.25, "y":3}, {"x":12.25, "y":3, "w":1.75}, {"x":14, "y":3}, {"x":0, "y":4, "w":1.25}, {"x":1.25, "y":4, "w":1.25}, {"x":2.5, "y":4, "w":1.25}, {"x":3.75, "y":4, "w":2.25}, {"x":6, "y":4, "w":1.25}, {"x":7.25, "y":4, "w":2.75}, {"x":10, "y":4, "w":1.25}, {"x":11.25, "y":4, "w":1.25}, {"x":12.5, "y":4, "w":1.25}, {"x":13.75, "y":4, "w":1.25}]
+        },
+        
+        "LAYOUT_60_ansi": {
+            "layout": [{"x":0, "y":0}, {"x":1, "y":0}, {"x":2, "y":0}, {"x":3, "y":0}, {"x":4, "y":0}, {"x":5, "y":0}, {"x":6, "y":0}, {"x":7, "y":0}, {"x":8, "y":0}, {"x":9, "y":0}, {"x":10, "y":0}, {"x":11, "y":0}, {"x":12, "y":0}, {"x":13, "y":0, "w":2}, {"x":0, "y":1, "w":1.5}, {"x":1.5, "y":1}, {"x":2.5, "y":1}, {"x":3.5, "y":1}, {"x":4.5, "y":1}, {"x":5.5, "y":1}, {"x":6.5, "y":1}, {"x":7.5, "y":1}, {"x":8.5, "y":1}, {"x":9.5, "y":1}, {"x":10.5, "y":1}, {"x":11.5, "y":1}, {"x":12.5, "y":1}, {"x":13.5, "y":1, "w":1.5}, {"x":0, "y":2, "w":1.75}, {"x":1.75, "y":2}, {"x":2.75, "y":2}, {"x":3.75, "y":2}, {"x":4.75, "y":2}, {"x":5.75, "y":2}, {"x":6.75, "y":2}, {"x":7.75, "y":2}, {"x":8.75, "y":2}, {"x":9.75, "y":2}, {"x":10.75, "y":2}, {"x":11.75, "y":2}, {"x":12.75, "y":2, "w":2.25}, {"x":0, "y":3, "w":2.25}, {"x":2.25, "y":3}, {"x":3.25, "y":3}, {"x":4.25, "y":3}, {"x":5.25, "y":3}, {"x":6.25, "y":3}, {"x":7.25, "y":3}, {"x":8.25, "y":3}, {"x":9.25, "y":3}, {"x":10.25, "y":3}, {"x":11.25, "y":3}, {"x":12.25, "y":3, "w":2.75}, {"x":0, "y":4, "w":1.25}, {"x":1.25, "y":4, "w":1.25}, {"x":2.5, "y":4, "w":1.25}, {"x":3.75, "y":4, "w":6.25}, {"x":10, "y":4, "w":1.25}, {"x":11.25, "y":4, "w":1.25}, {"x":12.5, "y":4, "w":1.25}, {"x":13.75, "y":4, "w":1.25}]
+        },
+
+        "LAYOUT_60_hhkb": {
+            "layout": [{"x":0, "y":0}, {"x":1, "y":0}, {"x":2, "y":0}, {"x":3, "y":0}, {"x":4, "y":0}, {"x":5, "y":0}, {"x":6, "y":0}, {"x":7, "y":0}, {"x":8, "y":0}, {"x":9, "y":0}, {"x":10, "y":0}, {"x":11, "y":0}, {"x":12, "y":0}, {"x":13, "y":0}, {"x":14, "y":0}, {"x":0, "y":1, "w":1.5}, {"x":1.5, "y":1}, {"x":2.5, "y":1}, {"x":3.5, "y":1}, {"x":4.5, "y":1}, {"x":5.5, "y":1}, {"x":6.5, "y":1}, {"x":7.5, "y":1}, {"x":8.5, "y":1}, {"x":9.5, "y":1}, {"x":10.5, "y":1}, {"x":11.5, "y":1}, {"x":12.5, "y":1}, {"x":13.5, "y":1, "w":1.5}, {"x":0, "y":2, "w":1.75}, {"x":1.75, "y":2}, {"x":2.75, "y":2}, {"x":3.75, "y":2}, {"x":4.75, "y":2}, {"x":5.75, "y":2}, {"x":6.75, "y":2}, {"x":7.75, "y":2}, {"x":8.75, "y":2}, {"x":9.75, "y":2}, {"x":10.75, "y":2}, {"x":11.75, "y":2}, {"x":12.75, "y":2, "w":2.25}, {"x":0, "y":3, "w":2.25}, {"x":2.25, "y":3}, {"x":3.25, "y":3}, {"x":4.25, "y":3}, {"x":5.25, "y":3}, {"x":6.25, "y":3}, {"x":7.25, "y":3}, {"x":8.25, "y":3}, {"x":9.25, "y":3}, {"x":10.25, "y":3}, {"x":11.25, "y":3}, {"x":12.25, "y":3, "w":1.75}, {"x":14, "y":3}, {"x":1.5, "y":4}, {"x":2.5, "y":4, "w":1.5}, {"x":4, "y":4, "w":7}, {"x":11, "y":4, "w":1.5}, {"x":12.5, "y":4}]
+        }
+    }
+}

keyboards/foxlab/leaf60/universal/keymaps/default/config.h

@@ -0,0 +1,19 @@
+/* Copyright 2019 Fox Lab
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+
+// place overrides here

keyboards/foxlab/leaf60/universal/keymaps/default/keymap.c

@@ -0,0 +1,46 @@
+/* Copyright 2019 Fox Lab
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include QMK_KEYBOARD_H
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+	LAYOUT_all(
+		KC_ESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_GRV, KC_BSPC,
+		KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS, 
+		KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_ENT, 
+		KC_LSFT, KC_NO, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT, KC_DEL, 
+		KC_LCTL, KC_LGUI, KC_LALT, KC_SPC, KC_SPC, KC_SPC, KC_RALT, MO(1), KC_RGUI, KC_RCTL),
+
+	LAYOUT_all(
+		RESET, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_TRNS, KC_TRNS, 
+		KC_TRNS, BL_TOGG, BL_DEC, BL_INC, BL_STEP, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, 
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, 
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, 
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS)
+
+};
+
+void matrix_init_user(void) {
+
+}
+
+void matrix_scan_user(void) {
+
+}
+
+void led_set_user(uint8_t usb_led) {
+
+}

keyboards/foxlab/leaf60/universal/keymaps/default/readme.md

@@ -0,0 +1 @@
+# The default keymap for Universal Leaf60

keyboards/foxlab/leaf60/universal/readme.md

@@ -0,0 +1,13 @@
+# Fox Lab Leaf60
+
+A 60% gasket sandwich made by Fox Lab.
+
+Keyboard Maintainer: [Fox Lab](https://github.com/fox-lab), [MechMerlin](https://github.com/mechmerlin)  
+Hardware Supported: Leaf60 powered by the ATmega32U4  
+Hardware Availability: [Geekhack Group Buy](https://geekhack.org/index.php?topic=99002.0)  
+
+Make example for this keyboard (after setting up your build environment):
+
+    make foxlab/leaf60/universal:default
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/foxlab/leaf60/universal/rules.mk

@@ -0,0 +1,82 @@
+# MCU name
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   atmega32a    bootloadHID
+BOOTLOADER = atmel-dfu
+
+
+# If you don't know the bootloader type, then you can specify the
+# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
+#   Teensy halfKay      512
+#   Teensy++ halfKay    1024
+#   Atmel DFU loader    4096
+#   LUFA bootloader     4096
+#   USBaspLoader        2048
+# OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE = lite      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = no        # Console for debug(+400)
+COMMAND_ENABLE = no        # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE = no            # USB Nkey Rollover
+BACKLIGHT_ENABLE = yes       # Enable keyboard backlight functionality on B7 by default
+RGBLIGHT_ENABLE = yes        # Enable keyboard RGB underglow
+MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no           # Audio output on port C6
+FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
+HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)
+
+LAYOUTS = 60_ansi 60_hhkb

keyboards/foxlab/leaf60/universal/universal.c

@@ -0,0 +1,61 @@
+/* Copyright 2019 Fox Lab
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include "universal.h"
+
+// Optional override functions below.
+// You can leave any or all of these undefined.
+// These are only required if you want to perform custom actions.
+
+void matrix_init_kb(void) {
+  // put your keyboard start-up code here
+  // runs once when the firmware starts up
+  setPinOutput(E6);
+  matrix_init_user();
+}
+
+/*
+
+void matrix_scan_kb(void) {
+  // put your looping keyboard code here
+  // runs every cycle (a lot)
+
+  matrix_scan_user();
+}
+
+bool process_record_kb(uint16_t keycode, keyrecord_t *record) {
+  // put your per-action keyboard code here
+  // runs for every action, just before processing by the firmware
+
+  return process_record_user(keycode, record);
+}
+
+void led_set_kb(uint8_t usb_led) {
+  // put your keyboard LED indicator (ex: Caps Lock LED) toggling code here
+
+  led_set_user(usb_led);
+}
+
+*/
+
+
+void led_set_kb(uint8_t usb_led) {
+  if (IS_LED_ON(usb_led, USB_LED_CAPS_LOCK)) {
+    writePinLow(E6);
+  } else {
+    writePinHigh(E6);
+  }
+	led_set_user(usb_led);
+}

keyboards/foxlab/leaf60/universal/universal.h

@@ -0,0 +1,68 @@
+/* Copyright 2019 Fox Lab
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#pragma once
+
+#include "quantum.h"
+
+/* This a shortcut to help you visually see your layout.
+ *
+ * The first section contains all of the arguments representing the physical
+ * layout of the board and position of the keys.
+ *
+ * The second converts the arguments into a two-dimensional array which
+ * represents the switch matrix.
+ */
+#define LAYOUT_all( \
+	K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014, \
+	K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113,       \
+	K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211,       K213,       \
+	K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312, K313,       \
+	K400, K401, K402,       K404,       K406,       K408,       K410, K411, K412, K413        \
+) { \
+	{ K000,  K001,  K002,  K003,  K004,  K005,  K006,  K007,  K008,  K009,  K010,  K011,  K012,  K013,  K014 },  \
+	{ K100,  K101,  K102,  K103,  K104,  K105,  K106,  K107,  K108,  K109,  K110,  K111,  K112,  K113,  KC_NO }, \
+	{ K200,  K201,  K202,  K203,  K204,  K205,  K206,  K207,  K208,  K209,  K210,  K211,  KC_NO, K213,  KC_NO }, \
+	{ K300,  K301,  K302,  K303,  K304,  K305,  K306,  K307,  K308,  K309,  K310,  K311,  K312,  K313,  KC_NO }, \
+	{ K400,  K401,  K402,  KC_NO, K404,  KC_NO, K406,  KC_NO, K408,  KC_NO, K410,  K411,  K412,  K413,  KC_NO }  \
+}
+
+#define LAYOUT_60_ansi( \
+	K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K014, \
+	K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, \
+	K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211,       K213, \
+	K300, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312,             \
+	K400, K401, K402,             K406,                   K410, K411, K412, K413        \
+) { \
+	{ K000,  K001,  K002,  K003,  K004,  K005,  K006,  K007,  K008,  K009,  K010,  K011,  K012,  KC_NO, K014 },  \
+	{ K100,  K101,  K102,  K103,  K104,  K105,  K106,  K107,  K108,  K109,  K110,  K111,  K112,  K113,  KC_NO }, \
+	{ K200,  K201,  K202,  K203,  K204,  K205,  K206,  K207,  K208,  K209,  K210,  K211,  KC_NO, K213,  KC_NO }, \
+	{ K300,  KC_NO, K302,  K303,  K304,  K305,  K306,  K307,  K308,  K309,  K310,  K311,  K312,  KC_NO, KC_NO }, \
+	{ K400,  K401,  K402,  KC_NO, KC_NO, KC_NO, K406,  KC_NO, KC_NO, KC_NO, K410,  K411,  K412,  K413,  KC_NO }  \
+}
+
+#define LAYOUT_60_hhkb( \
+	K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014, \
+	K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113,       \
+	K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211,       K213,       \
+	K300,       K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312, K313,       \
+	K401, K402,                         K406,                   K410, K411                    \
+) { \
+	{ K000,  K001,  K002,  K003,  K004,  K005,  K006,  K007,  K008,  K009,  K010,  K011,  K012,  K013,  K014 },  \
+	{ K100,  K101,  K102,  K103,  K104,  K105,  K106,  K107,  K108,  K109,  K110,  K111,  K112,  K113,  KC_NO }, \
+	{ K200,  K201,  K202,  K203,  K204,  K205,  K206,  K207,  K208,  K209,  K210,  K211,  KC_NO, K213,  KC_NO }, \
+	{ K300,  KC_NO, K302,  K303,  K304,  K305,  K306,  K307,  K308,  K309,  K310,  K311,  K312,  K313,  KC_NO }, \
+	{ KC_NO, K401,  K402,  KC_NO, KC_NO, KC_NO, K406,  KC_NO, KC_NO, KC_NO, K410,  K411,  KC_NO, KC_NO, KC_NO }  \
+}

keyboards/ft/mars80/config.h

@@ -0,0 +1,50 @@
+/*
+Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+#include "config_common.h"
+
+#define VENDOR_ID       0x20A0
+#define PRODUCT_ID      0x422D
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    FT
+#define PRODUCT         Mars 8.0
+#define DESCRIPTION     A custom TKL Keyboard
+
+#define RGBLED_NUM 20
+
+#define MATRIX_ROWS 7
+#define MATRIX_COLS 14
+//                        0   1   2   3   4   5   6   7   8   9   A   B   C   D
+#define MATRIX_ROW_PINS { B0, B1, B2, B3, B5, B6, B7 }
+#define MATRIX_COL_PINS { A0, A1, A2, A3, A4, A5, A6, A7, C7, C6, C5, C4, C3, C2 }
+#define UNUSED_PINS     {}
+
+#define DIODE_DIRECTION COL2ROW
+#define DEBOUNCING_DELAY 5
+
+#define NO_BACKLIGHT_CLOCK
+#define BACKLIGHT_LEVELS 1
+#define RGBLIGHT_ANIMATIONS
+
+#define NO_UART 1
+
+/* key combination for magic key command */
+/* defined by default; to change, uncomment and set to the combination you want */
+// #define IS_COMMAND() (get_mods() == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)))
+

keyboards/ft/mars80/info.json

@@ -0,0 +1,16 @@
+{
+    "keyboard_name": "Mars 8.0", 
+    "url": "", 
+    "maintainer": "qmk", 
+    "width": 18.25, 
+    "height": 6.5, 
+    "layouts": {
+        "LAYOUT_tkl_ansi": {
+            "layout": [{"x":0, "y":0}, {"x":2, "y":0}, {"x":3, "y":0}, {"x":4, "y":0}, {"x":5, "y":0}, {"x":6.5, "y":0}, {"x":7.5, "y":0}, {"x":8.5, "y":0}, {"x":9.5, "y":0}, {"x":11, "y":0}, {"x":12, "y":0}, {"x":13, "y":0}, {"x":14, "y":0}, {"x":15.25, "y":0}, {"x":16.25, "y":0}, {"x":17.25, "y":0}, {"x":0, "y":1.5}, {"x":1, "y":1.5}, {"x":2, "y":1.5}, {"x":3, "y":1.5}, {"x":4, "y":1.5}, {"x":5, "y":1.5}, {"x":6, "y":1.5}, {"x":7, "y":1.5}, {"x":8, "y":1.5}, {"x":9, "y":1.5}, {"x":10, "y":1.5}, {"x":11, "y":1.5}, {"x":12, "y":1.5}, {"x":13, "y":1.5, "w":2}, {"x":15.25, "y":1.5}, {"x":16.25, "y":1.5}, {"x":17.25, "y":1.5}, {"x":0, "y":2.5, "w":1.5}, {"x":1.5, "y":2.5}, {"x":2.5, "y":2.5}, {"x":3.5, "y":2.5}, {"x":4.5, "y":2.5}, {"x":5.5, "y":2.5}, {"x":6.5, "y":2.5}, {"x":7.5, "y":2.5}, {"x":8.5, "y":2.5}, {"x":9.5, "y":2.5}, {"x":10.5, "y":2.5}, {"x":11.5, "y":2.5}, {"x":12.5, "y":2.5}, {"x":13.5, "y":2.5, "w":1.5}, {"x":15.25, "y":2.5}, {"x":16.25, "y":2.5}, {"x":17.25, "y":2.5}, {"x":0, "y":3.5, "w":1.75}, {"x":1.75, "y":3.5}, {"x":2.75, "y":3.5}, {"x":3.75, "y":3.5}, {"x":4.75, "y":3.5}, {"x":5.75, "y":3.5}, {"x":6.75, "y":3.5}, {"x":7.75, "y":3.5}, {"x":8.75, "y":3.5}, {"x":9.75, "y":3.5}, {"x":10.75, "y":3.5}, {"x":11.75, "y":3.5}, {"x":12.75, "y":3.5, "w":2.25}, {"x":0, "y":4.5, "w":2.25}, {"x":2.25, "y":4.5}, {"x":3.25, "y":4.5}, {"x":4.25, "y":4.5}, {"x":5.25, "y":4.5}, {"x":6.25, "y":4.5}, {"x":7.25, "y":4.5}, {"x":8.25, "y":4.5}, {"x":9.25, "y":4.5}, {"x":10.25, "y":4.5}, {"x":11.25, "y":4.5}, {"x":12.25, "y":4.5, "w":2.75}, {"x":16.25, "y":4.5}, {"x":0, "y":5.5, "w":1.25}, {"x":1.25, "y":5.5, "w":1.25}, {"x":2.5, "y":5.5, "w":1.25}, {"x":3.75, "y":5.5, "w":6.25}, {"x":10, "y":5.5, "w":1.25}, {"x":11.25, "y":5.5, "w":1.25}, {"x":12.5, "y":5.5, "w":1.25}, {"x":13.75, "y":5.5, "w":1.25}, {"x":15.25, "y":5.5}, {"x":16.25, "y":5.5}, {"x":17.25, "y":5.5}]
+        },
+
+        "LAYOUT_tkl_iso": {
+            "layout": [{"x":0, "y":0}, {"x":2, "y":0}, {"x":3, "y":0}, {"x":4, "y":0}, {"x":5, "y":0}, {"x":6.5, "y":0}, {"x":7.5, "y":0}, {"x":8.5, "y":0}, {"x":9.5, "y":0}, {"x":11, "y":0}, {"x":12, "y":0}, {"x":13, "y":0}, {"x":14, "y":0}, {"x":15.25, "y":0}, {"x":16.25, "y":0}, {"x":17.25, "y":0}, {"x":0, "y":1.5}, {"x":1, "y":1.5}, {"x":2, "y":1.5}, {"x":3, "y":1.5}, {"x":4, "y":1.5}, {"x":5, "y":1.5}, {"x":6, "y":1.5}, {"x":7, "y":1.5}, {"x":8, "y":1.5}, {"x":9, "y":1.5}, {"x":10, "y":1.5}, {"x":11, "y":1.5}, {"x":12, "y":1.5}, {"x":13, "y":1.5, "w":2}, {"x":15.25, "y":1.5}, {"x":16.25, "y":1.5}, {"x":17.25, "y":1.5}, {"x":0, "y":2.5, "w":1.5}, {"x":1.5, "y":2.5}, {"x":2.5, "y":2.5}, {"x":3.5, "y":2.5}, {"x":4.5, "y":2.5}, {"x":5.5, "y":2.5}, {"x":6.5, "y":2.5}, {"x":7.5, "y":2.5}, {"x":8.5, "y":2.5}, {"x":9.5, "y":2.5}, {"x":10.5, "y":2.5}, {"x":11.5, "y":2.5}, {"x":12.5, "y":2.5}, {"x":13.75, "y":2.5, "w":1.25, "h":2}, {"x":15.25, "y":2.5}, {"x":16.25, "y":2.5}, {"x":17.25, "y":2.5}, {"x":0, "y":3.5, "w":1.75}, {"x":1.75, "y":3.5}, {"x":2.75, "y":3.5}, {"x":3.75, "y":3.5}, {"x":4.75, "y":3.5}, {"x":5.75, "y":3.5}, {"x":6.75, "y":3.5}, {"x":7.75, "y":3.5}, {"x":8.75, "y":3.5}, {"x":9.75, "y":3.5}, {"x":10.75, "y":3.5}, {"x":11.75, "y":3.5}, {"x":12.75, "y":3.5}, {"x":0, "y":4.5, "w":1.25}, {"x":1.25, "y":4.5}, {"x":2.25, "y":4.5}, {"x":3.25, "y":4.5}, {"x":4.25, "y":4.5}, {"x":5.25, "y":4.5}, {"x":6.25, "y":4.5}, {"x":7.25, "y":4.5}, {"x":8.25, "y":4.5}, {"x":9.25, "y":4.5}, {"x":10.25, "y":4.5}, {"x":11.25, "y":4.5}, {"x":12.25, "y":4.5, "w":2.75}, {"x":16.25, "y":4.5}, {"x":0, "y":5.5, "w":1.25}, {"x":1.25, "y":5.5, "w":1.25}, {"x":2.5, "y":5.5, "w":1.25}, {"x":3.75, "y":5.5, "w":6.25}, {"x":10, "y":5.5, "w":1.25}, {"x":11.25, "y":5.5, "w":1.25}, {"x":12.5, "y":5.5, "w":1.25}, {"x":13.75, "y":5.5, "w":1.25}, {"x":15.25, "y":5.5}, {"x":16.25, "y":5.5}, {"x":17.25, "y":5.5}]
+        }
+    }
+}

keyboards/ft/mars80/keymaps/default/config.h

@@ -0,0 +1,19 @@
+/* Copyright 2019 MechMerlin
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+
+// place overrides here

keyboards/ft/mars80/keymaps/default/keymap.c

@@ -0,0 +1,75 @@
+/* Copyright 2019 MechMerlin
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include QMK_KEYBOARD_H
+
+// Defines the keycodes used by our macros in process_record_user
+enum custom_keycodes {
+  QMKBEST = SAFE_RANGE,
+  QMKURL
+};
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+    [0] = LAYOUT_tkl_ansi(
+        KC_ESC,           KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,       KC_PSCR, KC_SLCK, KC_BRK,  \
+        KC_GRV,  KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    KC_MINS, KC_EQL,  KC_BSPC,      KC_INS,  KC_HOME, KC_PGUP, \
+        KC_TAB,  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_LBRC, KC_RBRC, KC_BSLS,      KC_DEL,  KC_END,  KC_PGDN, \
+        KC_CAPS, KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN, KC_QUOT,          KC_ENT,                                  \
+        KC_LSFT,          KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH,          KC_RSFT,               KC_UP,            \
+        KC_LCTL, KC_LGUI, KC_LALT,                            KC_SPC,                             KC_RALT, KC_RGUI, MO(1), KC_RCTL,      KC_LEFT, KC_DOWN, KC_RGHT  \
+    ),
+    [1] = LAYOUT_tkl_ansi(
+        _______,          _______, _______, _______, _______, _______, _______, _______, _______, KC_MSTP, KC_MPLY, KC_MPRV, KC_MNXT,      KC_MUTE, KC_VOLD, KC_VOLU, \
+        _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,      _______, _______, _______, \
+        _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,      _______, _______, _______, \
+        _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,          KC_MSEL,                                 \
+        _______,          _______, _______, KC_CALC, _______, _______, _______, _______, _______, _______, _______,          _______,               _______,          \
+        _______, _______, _______,                            _______,                            _______, _______, _______, _______,      _______, _______, _______  \
+    ),
+};
+
+bool process_record_user(uint16_t keycode, keyrecord_t *record) {
+  switch (keycode) {
+    case QMKBEST:
+      if (record->event.pressed) {
+        // when keycode QMKBEST is pressed
+        SEND_STRING("QMK is the best thing ever!");
+      } else {
+        // when keycode QMKBEST is released
+      }
+      break;
+    case QMKURL:
+      if (record->event.pressed) {
+        // when keycode QMKURL is pressed
+        SEND_STRING("https://qmk.fm/" SS_TAP(X_ENTER));
+      } else {
+        // when keycode QMKURL is released
+      }
+      break;
+  }
+  return true;
+}
+
+void matrix_init_user(void) {
+
+}
+
+void matrix_scan_user(void) {
+
+}
+
+void led_set_user(uint8_t usb_led) {
+
+}

keyboards/ft/mars80/keymaps/default/readme.md

@@ -0,0 +1 @@
+# The default keymap for Mars 8.0

keyboards/ft/mars80/mars80.c

@@ -0,0 +1,91 @@
+/* Copyright 2019 MechMerlin
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include "mars80.h"
+
+#include "rgblight.h"
+#include "i2c_master.h"
+#include "quantum.h"
+
+#ifdef RGBLIGHT_ENABLE
+extern rgblight_config_t rgblight_config;
+
+void rgblight_set(void) {
+    if (!rgblight_config.enable) {
+        for (uint8_t i = 0; i < RGBLED_NUM; i++) {
+            led[i].r = 0;
+            led[i].g = 0;
+            led[i].b = 0;
+        }
+    }
+
+    i2c_init();
+    i2c_transmit(0xb0, (uint8_t*)led, 3 * RGBLED_NUM, 100);
+}
+#endif
+
+void matrix_init_kb(void) {
+#ifdef RGBLIGHT_ENABLE
+    if (rgblight_config.enable) {
+        i2c_init();
+        i2c_transmit(0xb0, (uint8_t*)led, 3 * RGBLED_NUM, 100);
+    }
+#endif
+    // call user level keymaps, if any
+    matrix_init_user();
+}
+
+void matrix_scan_kb(void) {
+#ifdef RGBLIGHT_ENABLE
+    rgblight_task();
+#endif
+    matrix_scan_user();
+    /* Nothing else for now. */
+}
+
+__attribute__ ((weak))
+void matrix_scan_user(void) {
+}
+
+void backlight_init_ports(void) {
+    // initialize pins D0, D1, D4 and D6 as output
+    setPinOutput(D0);
+    setPinOutput(D1);
+    setPinOutput(D4);
+    setPinOutput(D6);
+
+    // turn backlight LEDs on
+    writePinHigh(D0);
+    writePinHigh(D1);
+    writePinHigh(D4);
+    writePinHigh(D6);
+}
+
+void backlight_set(uint8_t level) {
+	if (level == 0) {
+        // turn backlight LEDs off
+        writePinLow(D0);
+        writePinLow(D1);
+        writePinLow(D4);
+        writePinLow(D6);
+	} else {
+        // turn backlight LEDs on
+        writePinHigh(D0);
+        writePinHigh(D1);
+        writePinHigh(D4);
+        writePinHigh(D6);
+	}
+}

keyboards/ft/mars80/mars80.h

@@ -0,0 +1,63 @@
+/* Copyright 2019 MechMerlin
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#pragma once
+
+#include "quantum.h"
+
+/* This a shortcut to help you visually see your layout.
+ *
+ * The first section contains all of the arguments representing the physical
+ * layout of the board and position of the keys.
+ *
+ * The second converts the arguments into a two-dimensional array which
+ * represents the switch matrix.
+ */
+
+#define LAYOUT_tkl_iso( \
+    k11, k13, k14, k15, k16, k18, k19, k1A, k1B, k1C, k10, k1D, k12, k02, k03, k00,      \
+    k21, k22, k23, k24, k25, k26, k27, k28, k29, k2A, k2B, k2C, k20, k2D, k07, k06, k05, \
+    k31, k32, k33, k34, k35, k36, k37, k38, k39, k3A, k3B, k3C, k30, k0D, k09, k08,      \
+    k41, k42, k43, k44, k45, k46, k47, k48, k49, k4A, k4B, k4C, k3D, k40,                \
+    k51, k4D, k52, k53, k54, k55, k56, k57, k58, k59, k5A, k5B, k5C, k5D,                \
+    k61, k62, k63, k65, k69, k6A, k6B, k6C, k60, k6D, k68                                \
+) \
+{ \
+   { k00,   KC_NO, k02, k03, KC_NO, k05, k06,   k07,   k08, k09, KC_NO, KC_NO, KC_NO, k0D   }, \
+   { k10,   k11,   k12, k13, k14,   k15, k16,   KC_NO, k18, k19, k1A,   k1B,   k1C,   k1D   }, \
+   { k20,   k21,   k22, k23, k24,   k25, k26,   k27,   k28, k29, k2A,   k2B,   KC_NO, k2D   }, \
+   { k30,   k31,   k32, k33, k34,   k35, k36,   k37,   k38, k39, k3A,   k3B,   k3C,   k3D   }, \
+   { k40,   k41,   k42, k43, k44,   k45, k46,   k47,   k48, k49, k4A,   k4B,   k4C,   k4D   }, \
+   { KC_NO, k51,   k52, k53, k54,   k55, k56,   k57,   k58, k59, k5A,   k5B,   k5C,   k5D   }, \
+   { k60,   k61,   k62, k63, KC_NO, k65, KC_NO, KC_NO, k68, k69, k6A,   k6B,   k6C,   k6D   }, \
+}
+
+#define LAYOUT_tkl_ansi( \
+    k11, k13, k14, k15, k16, k18, k19, k1A, k1B, k1C, k10, k1D, k12, k02, k03, k00,      \
+    k21, k22, k23, k24, k25, k26, k27, k28, k29, k2A, k2B, k2C, k20, k2D, k07, k06, k05, \
+    k31, k32, k33, k34, k35, k36, k37, k38, k39, k3A, k3B, k3C, k30, k3D, k0D, k09, k08, \
+    k41, k42, k43, k44, k45, k46, k47, k48, k49, k4A, k4B, k4C, k40,                     \
+    k51, k52, k53, k54, k55, k56, k57, k58, k59, k5A, k5B, k5C, k5D,                     \
+    k61, k62, k63, k65, k69, k6A, k6B, k6C, k60, k6D, k68                                \
+) \
+{ \
+   { k00,   KC_NO, k02, k03, KC_NO, k05, k06,   k07,   k08, k09, KC_NO, KC_NO, KC_NO, k0D   }, \
+   { k10,   k11,   k12, k13, k14,   k15, k16,   KC_NO, k18, k19, k1A,   k1B,   k1C,   k1D   }, \
+   { k20,   k21,   k22, k23, k24,   k25, k26,   k27,   k28, k29, k2A,   k2B,   KC_NO, k2D   }, \
+   { k30,   k31,   k32, k33, k34,   k35, k36,   k37,   k38, k39, k3A,   k3B,   k3C,   k3D   }, \
+   { k40,   k41,   k42, k43, k44,   k45, k46,   k47,   k48, k49, k4A,   k4B,   k4C,   KC_NO }, \
+   { KC_NO, k51,   k52, k53, k54,   k55, k56,   k57,   k58, k59, k5A,   k5B,   k5C,   k5D   }, \
+   { k60,   k61,   k62, k63, KC_NO, k65, KC_NO, KC_NO, k68, k69, k6A,   k6B,   k6C,   k6D   }, \
+}

keyboards/ft/mars80/readme.md

@@ -0,0 +1,44 @@
+# Mars 8.0
+
+TKL Keyboard with in switch backlight and RGB Underglow. 
+
+Keyboard Maintainer: [MechMerlin](https://github.com/mechmerlin)  
+Hardware Supported: Mars 8.0 PCB  
+Hardware Availability: [Geekhack Group Buy](https://geekhack.org/index.php?topic=93723.0)  
+
+Make example for this keyboard (after setting up your build environment):
+
+    make ft/mars80:default
+
+Flashing
+
+ps2avr(GB) boards use an atmega32a microcontroller and a different bootloader. It is not flashable using the regular QMK methods. 
+
+**Reset Key:** Hold down the key located at `K00`, commonly programmed as `Pause/Break` while plugging in the keyboard.
+
+Windows: 
+1. Download [HIDBootFlash](http://vusb.wikidot.com/project:hidbootflash).
+2. Place your keyboard into reset. 
+3. Press the `Find Device` button and ensure that your keyboard is found.
+4. Press the `Open .hex File` button and locate the `.hex` file you created.
+5. Press the `Flash Device` button and wait for the process to complete. 
+
+macOS:
+1. Install homebrew by typing the following:   
+    ```
+    /usr/bin/ruby -e "$(curl -fsSL https://raw.githubusercontent.com/Homebrew/install/master/install)"
+    ```
+2. Install `crosspack-avr`.  
+    ```
+    brew cask install crosspack-avr
+    ```
+3. Install the following packages:
+    ```
+    brew install python3
+    pip3 install pyusb
+    brew install --HEAD https://raw.githubusercontent.com/robertgzr/homebrew-tap/master/bootloadhid.rb
+    ```
+4. Place your keyboard into reset. 
+5. Flash the board by typing `bootloadHID -r` followed by the path to your `.hex` file. 
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/ft/mars80/rules.mk

@@ -0,0 +1,50 @@
+# Copyright 2019 Luiz Ribeiro <luizribeiro@gmail.com>
+#
+# This program is free software: you can redistribute it and/or modify
+# it under the terms of the GNU General Public License as published by
+# the Free Software Foundation, either version 2 of the License, or
+# (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program.  If not, see <http://www.gnu.org/licenses/>.
+
+# MCU name
+MCU = atmega32a
+PROTOCOL = VUSB
+
+# unsupported features for now
+NO_UART = yes
+NO_SUSPEND_POWER_DOWN = yes
+
+# processor frequency
+F_CPU = 12000000
+
+# Bootloader
+#     This definition is optional, and if your keyboard supports multiple bootloaders of
+#     different sizes, comment this out, and the correct address will be loaded
+#     automatically (+60). See bootloader.mk for all options.
+BOOTLOADER = bootloadHID
+
+# build options
+BOOTMAGIC_ENABLE = no
+MOUSEKEY_ENABLE = no
+EXTRAKEY_ENABLE = yes
+CONSOLE_ENABLE = yes
+COMMAND_ENABLE = yes
+BACKLIGHT_ENABLE = yes
+RGBLIGHT_ENABLE = yes
+RGBLIGHT_CUSTOM_DRIVER = yes
+
+OPT_DEFS = -DDEBUG_LEVEL=0
+
+SRC += i2c_master.c
+
+# programming options
+PROGRAM_CMD = ./util/atmega32a_program.py $(TARGET).hex
+
+LAYOUTS = tkl_ansi tkl_iso

keyboards/ft/mars80/usbconfig.h

@@ -0,0 +1,393 @@
+/* Name: usbconfig.h
+ * Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
+ * Author: Christian Starkjohann
+ * Creation Date: 2005-04-01
+ * Tabsize: 4
+ * Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
+ * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
+ * This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
+ */
+
+#pragma once
+
+#include "config.h"
+
+/*
+General Description:
+This file is an example configuration (with inline documentation) for the USB
+driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
+also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
+wire the lines to any other port, as long as D+ is also wired to INT0 (or any
+other hardware interrupt, as long as it is the highest level interrupt, see
+section at the end of this file).
+*/
+
+/* ---------------------------- Hardware Config ---------------------------- */
+
+#define USB_CFG_IOPORTNAME      D
+/* This is the port where the USB bus is connected. When you configure it to
+ * "B", the registers PORTB, PINB and DDRB will be used.
+ */
+#define USB_CFG_DMINUS_BIT      3
+/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
+ * This may be any bit in the port.
+ */
+#define USB_CFG_DPLUS_BIT       2
+/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
+ * This may be any bit in the port. Please note that D+ must also be connected
+ * to interrupt pin INT0! [You can also use other interrupts, see section
+ * "Optional MCU Description" below, or you can connect D- to the interrupt, as
+ * it is required if you use the USB_COUNT_SOF feature. If you use D- for the
+ * interrupt, the USB interrupt will also be triggered at Start-Of-Frame
+ * markers every millisecond.]
+ */
+#define USB_CFG_CLOCK_KHZ       (F_CPU/1000)
+/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
+ * 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
+ * require no crystal, they tolerate +/- 1% deviation from the nominal
+ * frequency. All other rates require a precision of 2000 ppm and thus a
+ * crystal!
+ * Since F_CPU should be defined to your actual clock rate anyway, you should
+ * not need to modify this setting.
+ */
+#define USB_CFG_CHECK_CRC       0
+/* Define this to 1 if you want that the driver checks integrity of incoming
+ * data packets (CRC checks). CRC checks cost quite a bit of code size and are
+ * currently only available for 18 MHz crystal clock. You must choose
+ * USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
+ */
+
+/* ----------------------- Optional Hardware Config ------------------------ */
+
+/* #define USB_CFG_PULLUP_IOPORTNAME   D */
+/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
+ * V+, you can connect and disconnect the device from firmware by calling
+ * the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
+ * This constant defines the port on which the pullup resistor is connected.
+ */
+/* #define USB_CFG_PULLUP_BIT          4 */
+/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
+ * above) where the 1.5k pullup resistor is connected. See description
+ * above for details.
+ */
+
+/* --------------------------- Functional Range ---------------------------- */
+
+#define USB_CFG_HAVE_INTRIN_ENDPOINT    1
+/* Define this to 1 if you want to compile a version with two endpoints: The
+ * default control endpoint 0 and an interrupt-in endpoint (any other endpoint
+ * number).
+ */
+#define USB_CFG_HAVE_INTRIN_ENDPOINT3   1
+/* Define this to 1 if you want to compile a version with three endpoints: The
+ * default control endpoint 0, an interrupt-in endpoint 3 (or the number
+ * configured below) and a catch-all default interrupt-in endpoint as above.
+ * You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
+ */
+#define USB_CFG_EP3_NUMBER              3
+/* If the so-called endpoint 3 is used, it can now be configured to any other
+ * endpoint number (except 0) with this macro. Default if undefined is 3.
+ */
+/* #define USB_INITIAL_DATATOKEN           USBPID_DATA1 */
+/* The above macro defines the startup condition for data toggling on the
+ * interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
+ * Since the token is toggled BEFORE sending any data, the first packet is
+ * sent with the oposite value of this configuration!
+ */
+#define USB_CFG_IMPLEMENT_HALT          0
+/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
+ * for endpoint 1 (interrupt endpoint). Although you may not need this feature,
+ * it is required by the standard. We have made it a config option because it
+ * bloats the code considerably.
+ */
+#define USB_CFG_SUPPRESS_INTR_CODE      0
+/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
+ * want to send any data over them. If this macro is defined to 1, functions
+ * usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
+ * you need the interrupt-in endpoints in order to comply to an interface
+ * (e.g. HID), but never want to send any data. This option saves a couple
+ * of bytes in flash memory and the transmit buffers in RAM.
+ */
+#define USB_CFG_INTR_POLL_INTERVAL      1
+/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
+ * interval. The value is in milliseconds and must not be less than 10 ms for
+ * low speed devices.
+ */
+#define USB_CFG_IS_SELF_POWERED         0
+/* Define this to 1 if the device has its own power supply. Set it to 0 if the
+ * device is powered from the USB bus.
+ */
+#define USB_CFG_MAX_BUS_POWER           500
+/* Set this variable to the maximum USB bus power consumption of your device.
+ * The value is in milliamperes. [It will be divided by two since USB
+ * communicates power requirements in units of 2 mA.]
+ */
+#define USB_CFG_IMPLEMENT_FN_WRITE      1
+/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
+ * transfers. Set it to 0 if you don't need it and want to save a couple of
+ * bytes.
+ */
+#define USB_CFG_IMPLEMENT_FN_READ       0
+/* Set this to 1 if you need to send control replies which are generated
+ * "on the fly" when usbFunctionRead() is called. If you only want to send
+ * data from a static buffer, set it to 0 and return the data from
+ * usbFunctionSetup(). This saves a couple of bytes.
+ */
+#define USB_CFG_IMPLEMENT_FN_WRITEOUT   0
+/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
+ * You must implement the function usbFunctionWriteOut() which receives all
+ * interrupt/bulk data sent to any endpoint other than 0. The endpoint number
+ * can be found in 'usbRxToken'.
+ */
+#define USB_CFG_HAVE_FLOWCONTROL        0
+/* Define this to 1 if you want flowcontrol over USB data. See the definition
+ * of the macros usbDisableAllRequests() and usbEnableAllRequests() in
+ * usbdrv.h.
+ */
+#define USB_CFG_DRIVER_FLASH_PAGE       0
+/* If the device has more than 64 kBytes of flash, define this to the 64 k page
+ * where the driver's constants (descriptors) are located. Or in other words:
+ * Define this to 1 for boot loaders on the ATMega128.
+ */
+#define USB_CFG_LONG_TRANSFERS          0
+/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
+ * in a single control-in or control-out transfer. Note that the capability
+ * for long transfers increases the driver size.
+ */
+/* #define USB_RX_USER_HOOK(data, len)     if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
+/* This macro is a hook if you want to do unconventional things. If it is
+ * defined, it's inserted at the beginning of received message processing.
+ * If you eat the received message and don't want default processing to
+ * proceed, do a return after doing your things. One possible application
+ * (besides debugging) is to flash a status LED on each packet.
+ */
+/* #define USB_RESET_HOOK(resetStarts)     if(!resetStarts){hadUsbReset();} */
+/* This macro is a hook if you need to know when an USB RESET occurs. It has
+ * one parameter which distinguishes between the start of RESET state and its
+ * end.
+ */
+/* #define USB_SET_ADDRESS_HOOK()              hadAddressAssigned(); */
+/* This macro (if defined) is executed when a USB SET_ADDRESS request was
+ * received.
+ */
+#define USB_COUNT_SOF                   1
+/* define this macro to 1 if you need the global variable "usbSofCount" which
+ * counts SOF packets. This feature requires that the hardware interrupt is
+ * connected to D- instead of D+.
+ */
+/* #ifdef __ASSEMBLER__
+ * macro myAssemblerMacro
+ *     in      YL, TCNT0
+ *     sts     timer0Snapshot, YL
+ *     endm
+ * #endif
+ * #define USB_SOF_HOOK                    myAssemblerMacro
+ * This macro (if defined) is executed in the assembler module when a
+ * Start Of Frame condition is detected. It is recommended to define it to
+ * the name of an assembler macro which is defined here as well so that more
+ * than one assembler instruction can be used. The macro may use the register
+ * YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
+ * immediately after an SOF pulse may be lost and must be retried by the host.
+ * What can you do with this hook? Since the SOF signal occurs exactly every
+ * 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
+ * designs running on the internal RC oscillator.
+ * Please note that Start Of Frame detection works only if D- is wired to the
+ * interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
+ */
+#define USB_CFG_CHECK_DATA_TOGGLING     0
+/* define this macro to 1 if you want to filter out duplicate data packets
+ * sent by the host. Duplicates occur only as a consequence of communication
+ * errors, when the host does not receive an ACK. Please note that you need to
+ * implement the filtering yourself in usbFunctionWriteOut() and
+ * usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
+ * for each control- and out-endpoint to check for duplicate packets.
+ */
+#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH   0
+/* define this macro to 1 if you want the function usbMeasureFrameLength()
+ * compiled in. This function can be used to calibrate the AVR's RC oscillator.
+ */
+#define USB_USE_FAST_CRC                0
+/* The assembler module has two implementations for the CRC algorithm. One is
+ * faster, the other is smaller. This CRC routine is only used for transmitted
+ * messages where timing is not critical. The faster routine needs 31 cycles
+ * per byte while the smaller one needs 61 to 69 cycles. The faster routine
+ * may be worth the 32 bytes bigger code size if you transmit lots of data and
+ * run the AVR close to its limit.
+ */
+
+/* -------------------------- Device Description --------------------------- */
+
+#define USB_CFG_VENDOR_ID       (VENDOR_ID & 0xFF), ((VENDOR_ID >> 8) & 0xFF)
+/* USB vendor ID for the device, low byte first. If you have registered your
+ * own Vendor ID, define it here. Otherwise you may use one of obdev's free
+ * shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
+ * *** IMPORTANT NOTE ***
+ * This template uses obdev's shared VID/PID pair for Vendor Class devices
+ * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
+ * the implications!
+ */
+#define USB_CFG_DEVICE_ID       (PRODUCT_ID & 0xFF), ((PRODUCT_ID >> 8) & 0xFF)
+/* This is the ID of the product, low byte first. It is interpreted in the
+ * scope of the vendor ID. If you have registered your own VID with usb.org
+ * or if you have licensed a PID from somebody else, define it here. Otherwise
+ * you may use one of obdev's free shared VID/PID pairs. See the file
+ * USB-IDs-for-free.txt for details!
+ * *** IMPORTANT NOTE ***
+ * This template uses obdev's shared VID/PID pair for Vendor Class devices
+ * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
+ * the implications!
+ */
+#define USB_CFG_DEVICE_VERSION  0x00, 0x02
+/* Version number of the device: Minor number first, then major number.
+ */
+#define USB_CFG_VENDOR_NAME     'f', 't'
+#define USB_CFG_VENDOR_NAME_LEN 2
+/* These two values define the vendor name returned by the USB device. The name
+ * must be given as a list of characters under single quotes. The characters
+ * are interpreted as Unicode (UTF-16) entities.
+ * If you don't want a vendor name string, undefine these macros.
+ * ALWAYS define a vendor name containing your Internet domain name if you use
+ * obdev's free shared VID/PID pair. See the file USB-IDs-for-free.txt for
+ * details.
+ */
+#define USB_CFG_DEVICE_NAME     'm', 'a', 'r', 's', '8', '0'
+#define USB_CFG_DEVICE_NAME_LEN 6
+/* Same as above for the device name. If you don't want a device name, undefine
+ * the macros. See the file USB-IDs-for-free.txt before you assign a name if
+ * you use a shared VID/PID.
+ */
+/*#define USB_CFG_SERIAL_NUMBER   'N', 'o', 'n', 'e' */
+/*#define USB_CFG_SERIAL_NUMBER_LEN   0 */
+/* Same as above for the serial number. If you don't want a serial number,
+ * undefine the macros.
+ * It may be useful to provide the serial number through other means than at
+ * compile time. See the section about descriptor properties below for how
+ * to fine tune control over USB descriptors such as the string descriptor
+ * for the serial number.
+ */
+#define USB_CFG_DEVICE_CLASS        0
+#define USB_CFG_DEVICE_SUBCLASS     0
+/* See USB specification if you want to conform to an existing device class.
+ * Class 0xff is "vendor specific".
+ */
+#define USB_CFG_INTERFACE_CLASS     3   /* HID */
+#define USB_CFG_INTERFACE_SUBCLASS  1   /* Boot */
+#define USB_CFG_INTERFACE_PROTOCOL  1   /* Keyboard */
+/* See USB specification if you want to conform to an existing device class or
+ * protocol. The following classes must be set at interface level:
+ * HID class is 3, no subclass and protocol required (but may be useful!)
+ * CDC class is 2, use subclass 2 and protocol 1 for ACM
+ */
+#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH    0
+/* Define this to the length of the HID report descriptor, if you implement
+ * an HID device. Otherwise don't define it or define it to 0.
+ * If you use this define, you must add a PROGMEM character array named
+ * "usbHidReportDescriptor" to your code which contains the report descriptor.
+ * Don't forget to keep the array and this define in sync!
+ */
+
+/* #define USB_PUBLIC static */
+/* Use the define above if you #include usbdrv.c instead of linking against it.
+ * This technique saves a couple of bytes in flash memory.
+ */
+
+/* ------------------- Fine Control over USB Descriptors ------------------- */
+/* If you don't want to use the driver's default USB descriptors, you can
+ * provide our own. These can be provided as (1) fixed length static data in
+ * flash memory, (2) fixed length static data in RAM or (3) dynamically at
+ * runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
+ * information about this function.
+ * Descriptor handling is configured through the descriptor's properties. If
+ * no properties are defined or if they are 0, the default descriptor is used.
+ * Possible properties are:
+ *   + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
+ *     at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
+ *     used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
+ *     you want RAM pointers.
+ *   + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
+ *     in static memory is in RAM, not in flash memory.
+ *   + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
+ *     the driver must know the descriptor's length. The descriptor itself is
+ *     found at the address of a well known identifier (see below).
+ * List of static descriptor names (must be declared PROGMEM if in flash):
+ *   char usbDescriptorDevice[];
+ *   char usbDescriptorConfiguration[];
+ *   char usbDescriptorHidReport[];
+ *   char usbDescriptorString0[];
+ *   int usbDescriptorStringVendor[];
+ *   int usbDescriptorStringDevice[];
+ *   int usbDescriptorStringSerialNumber[];
+ * Other descriptors can't be provided statically, they must be provided
+ * dynamically at runtime.
+ *
+ * Descriptor properties are or-ed or added together, e.g.:
+ * #define USB_CFG_DESCR_PROPS_DEVICE   (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
+ *
+ * The following descriptors are defined:
+ *   USB_CFG_DESCR_PROPS_DEVICE
+ *   USB_CFG_DESCR_PROPS_CONFIGURATION
+ *   USB_CFG_DESCR_PROPS_STRINGS
+ *   USB_CFG_DESCR_PROPS_STRING_0
+ *   USB_CFG_DESCR_PROPS_STRING_VENDOR
+ *   USB_CFG_DESCR_PROPS_STRING_PRODUCT
+ *   USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
+ *   USB_CFG_DESCR_PROPS_HID
+ *   USB_CFG_DESCR_PROPS_HID_REPORT
+ *   USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
+ *
+ * Note about string descriptors: String descriptors are not just strings, they
+ * are Unicode strings prefixed with a 2 byte header. Example:
+ * int  serialNumberDescriptor[] = {
+ *     USB_STRING_DESCRIPTOR_HEADER(6),
+ *     'S', 'e', 'r', 'i', 'a', 'l'
+ * };
+ */
+
+#define USB_CFG_DESCR_PROPS_DEVICE                  0
+#define USB_CFG_DESCR_PROPS_CONFIGURATION           USB_PROP_IS_DYNAMIC
+//#define USB_CFG_DESCR_PROPS_CONFIGURATION           0
+#define USB_CFG_DESCR_PROPS_STRINGS                 0
+#define USB_CFG_DESCR_PROPS_STRING_0                0
+#define USB_CFG_DESCR_PROPS_STRING_VENDOR           0
+#define USB_CFG_DESCR_PROPS_STRING_PRODUCT          0
+#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER    0
+#define USB_CFG_DESCR_PROPS_HID                     USB_PROP_IS_DYNAMIC
+//#define USB_CFG_DESCR_PROPS_HID                     0
+#define USB_CFG_DESCR_PROPS_HID_REPORT              USB_PROP_IS_DYNAMIC
+//#define USB_CFG_DESCR_PROPS_HID_REPORT              0
+#define USB_CFG_DESCR_PROPS_UNKNOWN                 0
+
+#define usbMsgPtr_t unsigned short
+/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
+ * a scalar type here because gcc generates slightly shorter code for scalar
+ * arithmetics than for pointer arithmetics. Remove this define for backward
+ * type compatibility or define it to an 8 bit type if you use data in RAM only
+ * and all RAM is below 256 bytes (tiny memory model in IAR CC).
+ */
+
+/* ----------------------- Optional MCU Description ------------------------ */
+
+/* The following configurations have working defaults in usbdrv.h. You
+ * usually don't need to set them explicitly. Only if you want to run
+ * the driver on a device which is not yet supported or with a compiler
+ * which is not fully supported (such as IAR C) or if you use a differnt
+ * interrupt than INT0, you may have to define some of these.
+ */
+/* #define USB_INTR_CFG            MCUCR */
+/* #define USB_INTR_CFG_SET        ((1 << ISC00) | (1 << ISC01)) */
+/* #define USB_INTR_CFG_CLR        0 */
+/* #define USB_INTR_ENABLE         GIMSK */
+/* #define USB_INTR_ENABLE_BIT     INT0 */
+/* #define USB_INTR_PENDING        GIFR */
+/* #define USB_INTR_PENDING_BIT    INTF0 */
+/* #define USB_INTR_VECTOR         INT0_vect */
+
+/* Set INT1 for D- falling edge to count SOF */
+/* #define USB_INTR_CFG            EICRA */
+#define USB_INTR_CFG_SET        ((1 << ISC11) | (0 << ISC10))
+/* #define USB_INTR_CFG_CLR        0 */
+/* #define USB_INTR_ENABLE         EIMSK */
+#define USB_INTR_ENABLE_BIT     INT1
+/* #define USB_INTR_PENDING        EIFR */
+#define USB_INTR_PENDING_BIT    INTF1
+#define USB_INTR_VECTOR         INT1_vect

keyboards/georgi/config.h

@@ -23,7 +23,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 /* Defaults */
 
-#define VERSION "v1.0: Stenoknight"
+#define VERSION "v1.1: ClayM"
 #define VERBOSE
 
 #define FORCE_NKRO

keyboards/georgi/keymaps/colemak-dh/keymap.c

@@ -0,0 +1,306 @@
+/*
+ * Good on you for modifying your layout, this is the most nonQMK layout you will come across
+ * There are three modes, Steno (the default), QWERTY (Toggleable) and a Momentary symbol layer
+ *
+ * Don't modify the steno layer directly, instead add chords using the keycodes and macros
+ * from sten.h to the layout you want to modify.
+ *
+ * Observe the comment above processQWERTY!
+ *
+ * http://docs.gboards.ca
+ */
+
+#include QMK_KEYBOARD_H
+#include "sten.h"
+#include "keymap_steno.h"
+#define IGNORE_MOD_TAP_INTERRUPT
+
+// Steno Layers
+#define FUNCT	( LSD | LK | LP | LH )
+#define MEDIA	( LSD | LK | LW | LR )
+#define MOVE	( LSD | LK )
+#define NUM		( PWR )
+#define SYM		( RZ )
+
+// Keys and chords that, once they appear, are added to every subsequent partial chord
+// until the whole thing is sent.
+uint32_t stenoLayers[] = {NUM, SYM, MOVE, MEDIA, FUNCT};
+
+// QMK Layers
+#define STENO_LAYER   0
+#define GAMING		  1
+#define GAMING_2	  2
+
+/* Keyboard Layout
+ * ,---------------------------------.	  ,------------------------------.
+ * | FN  | LSU | LFT | LP | LH | ST1 |	  | ST3 | RF | RP | RL | RT | RD |
+ * |-----+-----+-----+----+----|-----|	  |-----|----+----+----+----+----|
+ * | PWR | LSD | LK  | LW | LR | ST2 |	  | ST4 | RR | RB | RG | RS | RZ |
+ * `---------------------------------'	  `------------------------------'
+ *					 ,---------------,	  .---------------.
+ *					 | LNO | LA | LO |	  | RE | RU | RNO |
+ *					 `---------------'	  `---------------'
+ */
+
+// Note: You can only use basic keycodes here!
+//
+// P() is just a wrapper to make your life easier.
+// PC() applies the mapping to all of the StenoLayers. For overloading, define these last.
+//
+// FN is unavailable. That is reserved for system use.
+// Chords containing PWR are always available, even in steno mode.
+//
+// http://docs.gboards.ca
+uint32_t processQwerty(bool lookup) {
+	// Special keys
+	P( RT  | RS  | RD  | RZ | LNO,		SEND_STRING(VERSION); SEND_STRING(__DATE__));
+	P( LFT | LK  | LP  | LW,			REPEAT());
+
+	// Mouse Keys
+	/* P( LO  | LSD | LK,	CLICK_MOUSE(KC_MS_BTN2)); */
+	/* P( LO  | LR  | LW,	CLICK_MOUSE(KC_MS_BTN1)); */
+
+
+/* Function layer
+ * ,-----------------------------------,    ,-----------------------------------,
+ * |     |     |     | NCTFUNCTF |     |    |     | F1  | F2  | F3  | F4  |     |
+ * |     +     +     +     +     +     |    |     + F5  + F6  + F7  + F8  +     |
+ * |     | FUNCTFUNC |     |     |     |    |     | F9  | F10 | F11 | F12 |     |
+ * `-----+-----+-----+-----+-----+-----'    `-----+-----+-----+-----+-----+-----'
+*/
+	P( FUNCT | RF,			SEND(KC_F1));
+	P( FUNCT | RP,			SEND(KC_F2));
+	P( FUNCT | RL,			SEND(KC_F3));
+	P( FUNCT | RT,			SEND(KC_F4));
+
+	P( FUNCT | RF | RR,		SEND(KC_F5));
+	P( FUNCT | RP | RB,		SEND(KC_F6));
+	P( FUNCT | RL | RG,		SEND(KC_F7));
+	P( FUNCT | RT | RS,		SEND(KC_F8));
+
+	P( FUNCT | RR,			SEND(KC_F9));
+	P( FUNCT | RG,			SEND(KC_F10));
+	P( FUNCT | RB,			SEND(KC_F11));
+	P( FUNCT | RS,			SEND(KC_F12));
+
+
+/* Movement layer
+ * ,-----------------------------------,    ,-----------------------------------,
+ * |     |     |     |     |     |     |    |     | <-  |  ↓  |  ↑  | ->  |     |
+ * |     +     +     +     +     +     |    |     +     +     +     +     +     |
+ * |     | MOVEMOVEM |     |     |     |    |     | Hm  | PgD | PgU | End |     |
+ * `-----+-----+-----+-----+-----+-----'    `-----+-----+-----+-----+-----+-----'
+*/
+	P( MOVE | RF,			SEND(KC_LEFT));
+	P( MOVE | RP,			SEND(KC_DOWN));
+	P( MOVE | RL,			SEND(KC_UP));
+	P( MOVE | RT,			SEND(KC_RIGHT));
+
+	P( MOVE | RR,			SEND(KC_HOME));
+	P( MOVE | RB,			SEND(KC_PGDN));
+	P( MOVE | RG,			SEND(KC_PGUP));
+	P( MOVE | RS,			SEND(KC_END));
+
+
+/* Media Layer
+ * ,-----------------------------------,    ,-----------------------------------,
+ * |     |     |     |     |     |     |    |     |Prev |Play | PLY |Next | VolU|
+ * |     +     +     +     +     +     |    |     +     +     +     +     +     |
+ * |     | MEDIAMEDIAMEDIAMEDIAM |     |    |     |     |     |     |Mute | VolD|
+ * `-----+-----+-----+-----+-----+-----'    `-----+-----+-----+-----+-----+-----'
+*/
+	P( MEDIA | RF,			SEND(KC_MPRV));
+	P( MEDIA | RP,			SEND(KC_MPLY));
+	P( MEDIA | RL,			SEND(KC_MPLY));
+	P( MEDIA | RT,			SEND(KC_MNXT));
+	P( MEDIA | RD,			SEND(KC_VOLU));
+
+	P( MEDIA | RS,			SEND(KC_MUTE));
+	P( MEDIA | RZ,			SEND(KC_VOLD));
+
+
+/* Numbers
+ * ,-----------------------------------,    ,-----------------------------------,
+ * |     |     |  a  |  b  |  c  |     |    |  :  |  1  |  2  |  3  |  .  |     |
+ * |     +     +  d  +  e  +  f  +     |    |  0  +  4  +  5  +  6  +  -  +     |
+ * | NUM |     |     |     |     |     |    |     |  7  |  8  |  9  |  0  |     |
+ * `-----+-----+-----+-----+-----+-----'    `-----+-----+-----+-----+-----+-----'
+*/
+	P( NUM | LFT,			SEND(KC_A));
+	P( NUM | LP,			SEND(KC_B));
+	P( NUM | LH,			SEND(KC_C));
+	P( NUM | LK,			SEND(KC_D));
+	P( NUM | LW,			SEND(KC_E));
+	P( NUM | LR,			SEND(KC_F));
+
+	// Right hand
+	P( NUM | ST3,			SEND_STRING(":"));
+	P( NUM | RF,			SEND(KC_1));
+	P( NUM | RP,			SEND(KC_2));
+	P( NUM | RL,			SEND(KC_3));
+	P( NUM | RT,			SEND(KC_DOT));
+
+	P( NUM | ST3 | ST4,		SEND(KC_0));
+	P( NUM | RF  | RR,		SEND(KC_4));
+	P( NUM | RP  | RB,		SEND(KC_5));
+	P( NUM | RG  | RL,		SEND(KC_6));
+	P( NUM | RT  | RS,		SEND(KC_MINUS));
+
+	P( NUM | RR,			SEND(KC_7));
+	P( NUM | RB,			SEND(KC_8));
+	P( NUM | RG,			SEND(KC_9));
+	P( NUM | RS,			SEND(KC_0));
+
+
+/* Symbols
+ * ,-----------------------------------,    ,-----------------------------------,
+ * |     |  `  |  [  |  {  |  (  |  <  |    |  >  |  )  |  }  |  ]  |  ?  |     |
+ * |     +  ~  +  -  +  '  +  :  +  _  |    |  \  +  =  +  "  +  +  +  ?  +     |
+ * |     |  !  |  @  |  #  |  $  |  %  |    |  |  |  ^  |  &  |  *  |  ?  | SYM |
+ * `-----+-----+-----+-----+-----+-----'    `-----+-----+-----+-----+-----+-----'
+*/
+	// Left hand
+	P( SYM | LSU,			SEND(KC_GRV));
+	P( SYM | LFT,			SEND(KC_LBRC));
+	P( SYM | LP,			SEND_STRING("{"));
+	P( SYM | LH,			SEND_STRING("("));
+	P( SYM | ST1,			SEND_STRING("<"));
+
+	P( SYM | LSU | LSD,		SEND_STRING("~"));
+	P( SYM | LFT | LK,		SEND(KC_MINS));
+	P( SYM | LP  | LW,		SEND(KC_QUOTE));
+	P( SYM | LH  | LR,		SEND_STRING(":"));
+	P( SYM | ST1 | ST2,		SEND_STRING("_"));
+
+	P( SYM | LSD,			SEND_STRING("!"));
+	P( SYM | LK,			SEND_STRING("@"));
+	P( SYM | LW,			SEND_STRING("#"));
+	P( SYM | LR,			SEND_STRING("$"));
+	P( SYM | ST2,			SEND_STRING("%"));
+
+	// Right hand
+	P( SYM | ST3,			SEND_STRING(">"));
+	P( SYM | RF,			SEND_STRING(")"));
+	P( SYM | RP,			SEND_STRING("}"));
+	P( SYM | RL,			SEND_STRING("]"));
+	P( SYM | RT,			SEND_STRING("?"));
+
+	P( SYM | ST3 | ST4,		SEND(KC_BSLASH));
+	P( SYM | RF  | RR,		SEND(KC_EQUAL));
+	P( SYM | RP  | RB,		SEND_STRING("\""));
+	P( SYM | RG  | RL,		SEND_STRING("+"));
+	P( SYM | RT  | RS,		SEND_STRING("?"));
+
+	P( SYM | ST4,			SEND_STRING("|"));
+	P( SYM | RR,			SEND_STRING("^"));
+	P( SYM | RB,			SEND_STRING("&"));
+	P( SYM | RG,			SEND_STRING("*"));
+	P( SYM | RS,			SEND_STRING("?"));
+
+
+/* Letters
+ * ,-----------------------------------,    ,-----------------------------------,
+ * |     |  Q  |  W  |  F  |  P  |  B  |    |  J  |  L  |  U  |  Y  |  ;  | ctl |
+ * +-----+- A -+- R -+- S -+- T -+- G -|    |- M -+- N -+- E -+- I -+- O -+-----|
+ * | bsp |  Z  |  X  |  C  |  D  |  V  |    |  K  |  H  |  ,  |  .  |  /  | del |
+ * `-----+-----+-----+-----+-----+-----'    `-----+-----+-----+-----+-----+-----'
+ *					   ,---------------,    .---------------.
+ *					   | alt | ent|shfr|    | spc| gui| alt |
+ *					   `---------------'    `---------------'
+*/
+	// Left hand
+	P( LSU,					SEND(KC_Q));
+	P( LFT,					SEND(KC_W));
+	P( LP,					SEND(KC_F));
+	P( LH,					SEND(KC_P));
+	P( ST1,					SEND(KC_B));
+
+	P( LSU | LSD,			SEND(KC_A));
+	P( LFT | LK,			SEND(KC_R));
+	P( LP  | LW,			SEND(KC_S));
+	P( LH  | LR,			SEND(KC_T));
+	P( ST1 | ST2,			SEND(KC_G));
+
+	P( LSD,					SEND(KC_Z));
+	P( LK,					SEND(KC_X));
+	P( LW,					SEND(KC_C));
+	P( LR,					SEND(KC_D));
+	P( ST2,					SEND(KC_V));
+
+	// Right hand
+	P( ST3,					SEND(KC_J));
+	P( RF,					SEND(KC_L));
+	P( RP,					SEND(KC_U));
+	P( RL,					SEND(KC_Y));
+	P( RT,					SEND(KC_SCLN));
+
+	P( ST3 | ST4,			SEND(KC_M));
+	P( RF  | RR,			SEND(KC_N));
+	P( RP  | RB,			SEND(KC_E));
+	P( RG  | RL,			SEND(KC_I));
+	P( RT  | RS,			SEND(KC_O));
+
+	P( ST4,					SEND(KC_K));
+	P( RR,					SEND(KC_H));
+	P( RB,					SEND(KC_COMM));
+	P( RG,					SEND(KC_DOT));
+	P( RS,					SEND(KC_SLSH));
+
+	// Thumb Chords and modifiers
+	//
+	PC( LNO | RNO | LA | RU,		SEND(KC_LCTL); SEND(KC_LSFT));
+	PC( LNO | LA  | RE,				SEND(KC_LCTL); SEND(KC_LSFT); SEND(KC_LALT));
+
+	// overrides
+	P( PWR | LO,			SEND(KC_LSFT); SEND(KC_BSPC));
+	P( PWR | RD,			SEND(KC_LCTL); SEND(KC_BSPC));
+	P( RZ | RD,				SEND(KC_LCTL); SEND(KC_DEL));
+
+	PC( LNO | LA | LO,		SEND(KC_LSFT); SEND(KC_ESC));
+	PC( LA | LO,			SEND(KC_ESC));
+	PC( LNO,				SEND(KC_LALT));
+	PC( LA,					SEND(KC_ENT));
+	PC( LO,					SEND(KC_LSFT));
+
+	PC( RNO,				SEND(KC_RALT));
+	PC( RE | RU,			SEND(KC_TAB));
+	PC( RE,					SEND(KC_SPC));
+	PC( RU,					SEND(KC_LGUI));
+   
+	PC( PWR,				SEND(KC_BSPC));
+	PC( RD,					SEND(KC_LCTL));
+	P( RZ,					SEND(KC_DEL));
+
+	return 0;
+}
+
+// "Layers"
+// Steno layer should be first in your map.
+// When PWR | FN | ST3 | ST4 is pressed, the layer is increased to the next map. You must return to STENO_LAYER at the end.
+// If you need more space for chords, remove the two gaming layers.
+// Note: If using NO_ACTION_TAPPING, LT will not work!
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+	// Main layer, everything goes through here
+	[STENO_LAYER] = LAYOUT_georgi(
+			STN_FN,  STN_S1,  STN_TL,  STN_PL,	STN_HL,  STN_ST1,		STN_ST3, STN_FR,  STN_PR,  STN_LR,	STN_TR,  STN_DR,
+			STN_PWR, STN_S2,  STN_KL,  STN_WL,	STN_RL,  STN_ST2,		STN_ST4, STN_RR,  STN_BR,  STN_GR,	STN_SR,  STN_ZR,
+								   STN_N1,		STN_A,	 STN_O,			STN_E,	 STN_U,   STN_N7
+	),
+	// Gaming layer with Numpad, Very limited
+	[GAMING] = LAYOUT_georgi(
+		KC_LSFT, KC_Q,	  KC_W,    KC_E,	KC_R,	 KC_T,						 KC_Y,	  KC_U,    KC_I,	KC_O,	 KC_P,	  KC_ENT,
+		KC_LCTL, KC_A,	  KC_S,    KC_D,	KC_F,	 KC_G,						 KC_H,	  KC_J,    KC_K,	KC_L,	 KC_SCLN, KC_DQUO,
+								   KC_LALT, KC_SPC,  LT(GAMING_2, KC_ENT),		 KC_DEL,  KC_ASTR, TO(STENO_LAYER)
+	),
+
+	[GAMING_2] = LAYOUT_georgi(
+		KC_LSFT, KC_1,	  KC_2,    KC_3,	KC_4,	 KC_5,			KC_6,	 KC_7,	  KC_8,    KC_9,	KC_0,	 KC_MINS,
+		KC_LCTL, KC_Z,	  KC_X,    KC_C,	KC_V,	 KC_B,			KC_N,	 KC_M,	  KC_LT,   KC_GT,	KC_QUES, KC_RSFT,
+								   KC_LALT, KC_SPC,  KC_ENT,		KC_DEL,  KC_ASTR, TO(STENO_LAYER)
+	)
+};
+
+// Don't fuck with this, thanks.
+size_t keymapsCount  = sizeof(keymaps)/sizeof(keymaps[0]);
+size_t stenoLayerCount = sizeof(stenoLayers)/sizeof(stenoLayers[0]);

keyboards/georgi/keymaps/colemak-dh/readme.md

@@ -0,0 +1,11 @@
+# Georgi QWERTY/Steno firmware
+
+This is the default keymap for Georgi, it's based heavily off of the naps62 ErgoDox and the Gergo layout. 
+It is both a ergonomic and programmer friendly keymap.
+
+Ideally you should copy this directory and make your changes there. If you come up with a good layout submit a PR!
+
+## Space issues
+If you find yourself running out of space for dictionary entries, disabling mousekeys in rules.mk will save
+you about 4k for entries!
+Get a free 1k by deleting the Gaming layers from the keymap!

keyboards/georgi/keymaps/colemak-dh/rules.mk

@@ -0,0 +1,45 @@
+#----------------------------------------------------------------------------
+# make georgi:claymager:dfu
+# Make sure you have dfu-programmer installed!
+#----------------------------------------------------------------------------
+
+NO_REPEAT				 = yes
+VERBOSE					 = yes
+KEYBOARD_SHARED_EP       = yes
+CUSTOM_MATRIX			 = yes
+STENO_LAYERS			 = yes
+
+#Firmware reduction options
+MOUSEKEY_ENABLE			 = yes 		# 1500 bytes
+NO_TAPPING				 = no 	    # 2000 bytes
+NO_PRINT				 = yes
+
+#Debug options
+CONSOLE_ENABLE			 = no
+DEBUG_MATRIX_SCAN_RATE   = no
+DEBUG_MATRIX			 = no
+ONLY_QWERTY				 = no
+
+# A bunch of stuff that you shouldn't touch unless you
+# know what you're doing.
+#
+# No touchy, capiche?
+SRC += matrix.c i2c_master.c
+ifeq ($(strip $(DEBUG_MATRIX)), yes)
+    OPT_DEFS += -DDEBUG_MATRIX
+endif
+ifeq ($(strip $(NO_REPEAT)), yes)
+    OPT_DEFS += -DNO_REPEAT
+endif
+ifeq ($(strip $(NO_PRINT)), yes)
+    OPT_DEFS += -DNO_PRINT -DNO_DEBUG
+endif
+ifeq ($(strip $(ONLY_QWERTY)), yes)
+    OPT_DEFS += -DONLYQWERTY
+endif
+ifeq ($(strip $(NO_TAPPING)), yes)
+    OPT_DEFS += -DNO_ACTION_TAPPING
+endif
+ifeq ($(strip $(STENO_LAYERS)), yes)
+    OPT_DEFS += -DSTENOLAYERS
+endif

keyboards/georgi/keymaps/default/keymap.c

@@ -38,6 +38,12 @@
 
 // Note: You can only use basic keycodes here!
 // P() is just a wrapper to make your life easier.
+// PC() applies the mapping to all of the StenoLayers.
+//   To overload, declare it with P() first.
+//   Be sure to enable in rules.mk and see colemak-dh for usage 
+//
+// FN is unavailable. That is reserved for system use.
+// Chords containing PWR are always available, even in steno mode.
 //
 // http://docs.gboards.ca
 uint32_t processQwerty(bool lookup) {
@@ -135,7 +141,7 @@ uint32_t processQwerty(bool lookup) {
     P( RZ,          SEND(KC_ESC));
 
     // Symbols and Numbers
-    P( PWR | RE | RU,      SEND(KC_ENT));
+ 	P( PWR | RE | RU,      SEND(KC_ENT));
     P( PWR | LA | LO,      SEND(KC_SPC));
     P( PWR | LP | LW,      SEND(KC_LSFT); SEND(KC_9));       // (
     P( PWR | LH | LR,      SEND(KC_LSFT); SEND(KC_0));       // )
@@ -169,6 +175,10 @@ uint32_t processQwerty(bool lookup) {
     P( PWR | RE,           SEND(KC_SCLN));
     P( PWR | RU,           SEND(KC_BSLS));
     P( PWR | LNO,          SEND(KC_BSLS));
+    P( PWR | RF | RR,      SEND(KC_LEFT));
+    P( PWR | RP | RB,      SEND(KC_DOWN));
+    P( PWR | RL | RG,      SEND(KC_UP));
+    P( PWR | RT | RS,      SEND(KC_RIGHT));
 
     // Letters
     P( LSU | LSD,    SEND(KC_A));

keyboards/georgi/keymaps/default/rules.mk

@@ -7,6 +7,7 @@ NO_REPEAT				 = no
 VERBOSE					 = yes
 KEYBOARD_SHARED_EP       = yes
 CUSTOM_MATRIX			 = yes
+STENO_LAYERS			 = no
 
 #Firmware reduction options
 MOUSEKEY_ENABLE			 = yes 		# 1500 bytes

keyboards/georgi/matrix.c

@@ -1,8 +1,4 @@
 /*
-Note for ErgoDox EZ customizers: Here be dragons!
-This is not a file you want to be messing with.
-All of the interesting stuff for you is under keymaps/ :)
-Love, Erez
 
 Copyright 2013 Oleg Kostyuk <cub.uanic@gmail.com>
 
@@ -248,8 +244,8 @@ uint8_t matrix_scan(void)
     matrix_scan_quantum();
 
 #ifdef DEBUG_MATRIX
-    for (uint8_t c = 0; c < MATRIX_COLS; c++) 
-		for (uint8_t r = 0; r < MATRIX_ROWS; r++) 
+    for (uint8_t c = 0; c < MATRIX_COLS; c++)
+		for (uint8_t r = 0; r < MATRIX_ROWS; r++)
 		  if (matrix_is_on(r, c)) xprintf("r:%d c:%d \n", r, c);
 #endif
 
@@ -359,7 +355,7 @@ static void select_row(uint8_t row)
     if (row < 7) {
         // select on mcp23018
         if (mcp23018_status) { // do nothing on error
-        } else { // set active row low  : 0 // set other rows hi-Z : 1 
+        } else { // set active row low  : 0 // set other rows hi-Z : 1
             mcp23018_status = i2c_start(I2C_ADDR_WRITE, ERGODOX_EZ_I2C_TIMEOUT);        if (mcp23018_status) goto out;
             mcp23018_status = i2c_write(GPIOA, ERGODOX_EZ_I2C_TIMEOUT);                 if (mcp23018_status) goto out;
             mcp23018_status = i2c_write(0xFF & ~(1<<row), ERGODOX_EZ_I2C_TIMEOUT);      if (mcp23018_status) goto out;

keyboards/georgi/sten.c

@@ -11,6 +11,18 @@ uint32_t pChord 		= 0;		// Previous Chord
 int		 pChordIndex 	= 0;		// Keys in previousachord
 uint32_t pChordState[32];			// Previous chord sate 
 uint32_t stickyBits = 0;			// Or'd with every incoming press
+#ifndef NO_DEBUG
+char debugMsg[32];
+#endif
+
+// StenoLayer
+uint32_t releasedChord	= 0;		// Keys released from current chord
+uint32_t tChord			= 0;		// Protects state of cChord
+
+#ifndef STENOLAYERS
+uint32_t stenoLayers[] = { PWR };
+size_t 	 stenoLayerCount = sizeof(stenoLayers)/sizeof(stenoLayers[0]);
+#endif
 
 // Mode state
 enum MODE { STENO = 0, QWERTY, COMMAND };

keyboards/georgi/sten.h

@@ -13,6 +13,9 @@
 
 extern size_t keymapsCount;			// Total keymaps
 extern uint32_t cChord;				// Current Chord
+extern uint32_t stenoLayers[];		// Chords that simulate QMK layers
+extern size_t stenoLayerCount;		// Number of simulated layers
+uint32_t refChord;					// Reference chord for PC macro
 
 // Function defs
 void 			processChord(bool useFakeSteno);
@@ -30,6 +33,11 @@ void 			CLICK_MOUSE(uint8_t);
 
 // Keymap helper
 #define P(chord, act) if (cChord == (chord)) { if (!lookup) {act;} return chord;}
+#define PC(chord, act) if (cChord == (chord)) { if (!lookup) {act;} return chord;} \
+	for(int i = 0; i < stenoLayerCount; i++) { \
+		refChord = stenoLayers[i] | chord; \
+		if (cChord == (refChord)) { if (!lookup) {act;} return refChord;}; \
+}
 
 // Shift to internal representation
 // i.e) S(teno)R(ight)F

keyboards/gergo/matrix.c

@@ -1,8 +1,4 @@
 /*
-Note for ErgoDox EZ customizers: Here be dragons!
-This is not a file you want to be messing with.
-All of the interesting stuff for you is under keymaps/ :)
-Love, Erez
 
 Copyright 2013 Oleg Kostyuk <cub.uanic@gmail.com>
 

keyboards/halberd/config.h

@@ -1,5 +1,4 @@
-/*
-Copyright 2018 takashiski
+/* Copyright 2019 ENDO Katsuhiro <ka2hiro@kagizaraya.jp>
 
 This program is free software: you can redistribute it and/or modify
 it under the terms of the GNU General Public License as published by
@@ -23,14 +22,13 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 #define VENDOR_ID       0xFEED
 #define PRODUCT_ID      0x0000
 #define DEVICE_VER      0x0001
-#define MANUFACTURER    takashiski
-#define PRODUCT         hecomi_alpha
-#define DESCRIPTION     asymmetric split keyboard
+#define MANUFACTURER    Kagizaraya
+#define PRODUCT         Halberd
+#define DESCRIPTION     40% keyboard
 
 /* key matrix size */
-//#define MATRIX_ROWS 5
-#define MATRIX_ROWS 10
-#define MATRIX_COLS 8
+#define MATRIX_ROWS 4
+#define MATRIX_COLS 11
 
 /*
  * Keyboard Matrix Assignments
@@ -42,41 +40,25 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
  *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
  *
 */
-#define MATRIX_ROW_PINS { C6,D7,E6,B4,B5 }
-#define MATRIX_COL_PINS { F4,F5,F6,F7,B1,B3,B2,B6 }
+#define MATRIX_ROW_PINS { D6, D4, D5, E6 }
+#define MATRIX_COL_PINS { D7, B4, C7, C6, B6, B5, F7, F6, F5, F4, F1 }
 #define UNUSED_PINS
-#define SOFT_SERIAL_PIN D0 // or D1, D2, D3, E6
-//#define USE_I2C
 
 /* COL2ROW, ROW2COL, or CUSTOM_MATRIX */
 #define DIODE_DIRECTION COL2ROW
 
-/*
- * Split Keyboard specific options, make sure you have 'SPLIT_KEYBOARD = yes' in your rules.mk, an3 define SOFT_SERIAL_PIN.
- */
-//#define SOFT_SERIAL_PIN D0 // or D1, D2, D3, E6
-
 // #define BACKLIGHT_PIN B7
 // #define BACKLIGHT_BREATHING
 // #define BACKLIGHT_LEVELS 3
 
- #define RGB_DI_PIN D4
- #ifdef RGB_DI_PIN
-   #define RGBLED_NUM 8
-   #define RGBLIGHT_HUE_STEP 8
-   #define RGBLIGHT_SAT_STEP 8
-   #define RGBLIGHT_VAL_STEP 8
- /*== or choose animations ==*/
-   #define RGBLIGHT_EFFECT_BREATHING
-   #define RGBLIGHT_EFFECT_RAINBOW_MOOD
-   #define RGBLIGHT_EFFECT_RAINBOW_SWIRL
-   #define RGBLIGHT_EFFECT_SNAKE
-   #define RGBLIGHT_EFFECT_KNIGHT
-   #define RGBLIGHT_EFFECT_CHRISTMAS
-   #define RGBLIGHT_EFFECT_STATIC_GRADIENT
-   #define RGBLIGHT_EFFECT_RGB_TEST
-   #define RGBLIGHT_EFFECT_ALTERNATING
- #endif
+#define RGB_DI_PIN F0
+#ifdef RGB_DI_PIN
+#define RGBLIGHT_ANIMATIONS
+#define RGBLED_NUM 40
+#define RGBLIGHT_HUE_STEP 8
+#define RGBLIGHT_SAT_STEP 8
+#define RGBLIGHT_VAL_STEP 8
+#endif
 
 /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
 #define DEBOUNCING_DELAY 5
@@ -129,6 +111,12 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
  *
  */
 
+/* key combination for magic key command */
+/*
+#define IS_COMMAND() ( \
+    keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
+)
+*/
 
 /* control how magic key switches layers */
 //#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true
@@ -238,9 +226,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 /* Bootmagic Lite key configuration */
 // #define BOOTMAGIC_LITE_ROW 0
 // #define BOOTMAGIC_LITE_COLUMN 0
-//
-/*
-#define USE_I2C
-#define MASTER_LEFT
-#define EEHANDS
-*/
+
+#define TAPPING_TERM    100
+
+

keyboards/halberd/halberd.c

@@ -0,0 +1,43 @@
+/* Copyright 2019 ENDO Katsuhiro <ka2hiro@kagizaraya.jp>
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include "halberd.h"
+
+void matrix_init_kb(void) {
+	// put your keyboard start-up code here
+	// runs once when the firmware starts up
+
+	matrix_init_user();
+}
+
+void matrix_scan_kb(void) {
+	// put your looping keyboard code here
+	// runs every cycle (a lot)
+
+	matrix_scan_user();
+}
+
+bool process_record_kb(uint16_t keycode, keyrecord_t *record) {
+	// put your per-action keyboard code here
+	// runs for every action, just before processing by the firmware
+
+	return process_record_user(keycode, record);
+}
+
+void led_set_kb(uint8_t usb_led) {
+	// put your keyboard LED indicator (ex: Caps Lock LED) toggling code here
+
+	led_set_user(usb_led);
+}

keyboards/halberd/halberd.h

@@ -0,0 +1,40 @@
+/* Copyright 2019 ENDO Katsuhiro <ka2hiro@kagizaraya.jp>
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#pragma once
+
+#include "quantum.h"
+
+/* This a shortcut to help you visually see your layout.
+ *
+ * The first section contains all of the arguments representing the physical
+ * layout of the board and position of the keys.
+ *
+ * The second converts the arguments into a two-dimensional array which
+ * represents the switch matrix.
+ */
+#define LAYOUT( \
+    K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K10, \
+    K11, K12, K13, K14, K15, K16, K17, K18, K19, K20, K21, \
+    K22, K23, K24, K25, K26, K27, K28, K29, K30, K31, K32, \
+              K33, K34, K35, K36, K37, K38, K39   \
+) \
+{ \
+    { K00,   K01,   K02,   K03,   K04,   K05,   K06,   K07,   K08,   K09,   K10 }, \
+    { K11,   K12,   K13,   K14,   K15,   K16,   K17,   K18,   K19,   K20,   K21 }, \
+    { K22,   K23,   K24,   K25,   K26,   K27,   K28,   K29,   K30,   K31,   K32 }, \
+    { KC_NO, KC_NO, K33,   K34,   K35,   K36,   K37,   K38,   K39,   KC_NO, KC_NO } \
+}
+

keyboards/halberd/info.json

@@ -0,0 +1,13 @@
+{
+    "keyboard_name": "Halberd", 
+    "url": "", 
+    "maintainer": "ka2hiro", 
+    "width": 11, 
+    "height": 4, 
+    "layouts": {
+        "LAYOUT": {
+            "layout": [{"label":"!", "x":0, "y":0}, {"label":"@", "x":1, "y":0}, {"label":"#", "x":2, "y":0}, {"label":"$", "x":3, "y":0}, {"label":"%", "x":4, "y":0}, {"label":"Tab", "x":5, "y":0}, {"label":"^", "x":6, "y":0}, {"label":"&", "x":7, "y":0}, {"label":"*", "x":8, "y":0}, {"label":"(", "x":9, "y":0}, {"label":")", "x":10, "y":0}, {"label":"Tab", "x":0, "y":1}, {"label":"_", "x":1, "y":1}, {"label":"+", "x":2, "y":1}, {"label":"|", "x":3, "y":1}, {"label":"~", "x":4, "y":1}, {"label":"BkSp", "x":5, "y":1}, {"label":":", "x":6, "y":1}, {"label":"\"", "x":7, "y":1}, {"label":">", "x":8, "y":1}, {"label":"{", "x":9, "y":1}, {"label":"}", "x":10, "y":1}, {"label":"Caps", "x":0, "y":2}, {"label":"-", "x":1, "y":2}, {"label":"=", "x":2, "y":2}, {"label":"\\", "x":3, "y":2}, {"label":"`", "x":4, "y":2}, {"label":"Enter", "x":5, "y":2}, {"label":";", "x":6, "y":2}, {"label":"'", "x":7, "y":2}, {"label":"<", "x":8, "y":2}, {"label":"[", "x":9, "y":2}, {"label":"]", "x":10, "y":2}, {"label":"GUI", "x":2, "y":3}, {"label":"Lower", "x":3, "y":3}, {"label":"Esc", "x":4, "y":3}, {"x":5, "y":3}, {"label":"Shift", "x":6, "y":3}, {"label":"Raise", "x":7, "y":3}, {"label":"Alt", "x":8, "y":3}]
+        }
+    }
+}
+

keyboards/halberd/keymaps/default/config.h

@@ -0,0 +1,19 @@
+/* Copyright 2019 ENDO Katsuhiro <ka2hiro@kagizaraya.jp>
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+
+// place overrides here

keyboards/halberd/keymaps/default/keymap.c

@@ -0,0 +1,160 @@
+/* Copyright 2019 ENDO Katsuhiro <ka2hiro@kagizaraya.jp>
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include QMK_KEYBOARD_H
+
+// Defines the keycodes used by our macros in process_record_user
+enum layer_names {
+    _QWERTY,
+    _LOWER,
+    _RAISE,
+    _ADJUST,
+};
+
+// Defines the keycodes used by our macros in process_record_user
+enum custom_keycodes {
+  QWERTY = SAFE_RANGE,
+  LOWER,
+  RAISE,
+  ADJUST,
+};
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+/* Qwerty
+ *
+ * ,----------------------------------------------------------------------------.
+ * |   Q  |   W  |   E  |   R  |   T  |  Tab |   Y  |   U  |   I  |   O  |   P  |
+ * |------+------+------+------+------|------|------+------+------+------+------|
+ * |   A  |   S  |   D  |   F  |   G  | BkSp |   H  |   J  |   K  |   L  |   ;  |
+ * |------+------+------+------+------|------|------+------+------+------+------|
+ * |   Z  |   X  |   C  |   V  |   B  | Enter|   N  |   M  |   ,  |   .  |   /  |
+ * `-------------+------+------+------|------|------+------+------+------+------'
+ *               | GUI  | LOWER|Ctrl/Esc|Space|Shift| RAISE| Alt |
+ *               `------------------------------------------------'
+ */
+[_QWERTY] = LAYOUT(
+  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_TAB,     KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,
+  KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_BSPC,     KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN,
+  KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_ENT,     KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH,
+                    KC_LGUI, LOWER, MT(MOD_LCTL, KC_ESC),  KC_SPC, KC_LSFT, RAISE, KC_LALT
+),
+
+/* Raise
+ *
+ * ,----------------------------------------------------------------------------.
+ * |   !  |   @  |   #  |   $  |   %  |      |   ^  |   &  |   *  |   (  |   )  |
+ * |------+------+------+------+------|------|------+------+------+------+------|
+ * |  Tab |   _  |   +  |  |   |  ~   |      |   :  |   "  |   >  |   {  |   }  |
+ * |------+------+------+------+------|------|------+------+------+------+------|
+ * |  Caps|   -  |   =  |  \   |  `   |      |   ;  |   '  |   <  |   [  |   ]  |
+ * `-------------+------+------+------|------|------+------+------+------+------'
+ *               |      | LOWER|      |      |  Esc | RAISE|      |
+ *               `------------------------------------------------'
+ */
+[_RAISE] = LAYOUT(
+  KC_EXLM, KC_AT,   KC_HASH, KC_DLR,  KC_PERC, _______, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN,
+  KC_TAB,  KC_UNDS, KC_PLUS, KC_PIPE, KC_TILD, _______, KC_COLN, KC_DQUO, KC_GT,   KC_LCBR, KC_RCBR,
+  KC_CAPS, KC_MINS, KC_EQL,  KC_BSLS, KC_GRV,  _______, KC_SCLN, KC_QUOT, KC_LT,   KC_LBRC, KC_RBRC,
+                    _______, _______, _______, _______, _______,  _______, _______
+),
+
+/* Lower
+ *
+ * ,----------------------------------------------------------------------------.
+ * |   1  |   2  |   3  |   4  |   5  |      |   6  |   7  |   8  |   9  |   0  |
+ * |------+------+------+------+------|------|------+------+------+------+------|
+ * |  Tab |      |      |      |Enter |      | Left | Down |  Up  | Right| Enter|
+ * |------+------+------+------+------|------|------+------+------+------+------|
+ * |  Ctrl|      |  GUI |  Alt | Del  |      | BkSp | PgUp | PgDn |      |      |
+ * `-------------+------+------+------|------|------+------+------+------+------'
+ *               |      | LOWER|      |      |      | RAISE|      |
+ *               `------------------------------------------------'
+ */
+[_LOWER] = LAYOUT(
+  KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    _______, KC_6,    KC_7,    KC_8,    KC_9,    KC_0,
+  KC_TAB,  _______, _______, _______, KC_ENT,  _______, KC_LEFT, KC_DOWN, KC_UP,   KC_RGHT, KC_ENT,
+  KC_LCTL, _______, KC_LGUI, KC_LALT, KC_DEL,  _______, KC_BSPC, KC_PGUP, KC_PGDN, _______, _______,
+                    _______, _______, _______, _______, _______, _______, _______
+),
+
+
+/* Adjust (Lower + Raise)
+ *
+ * ,----------------------------------------------------------------------------.
+ * |  F1  |  F2  |  F3  |  F4  |  F5  |      |   F6 |  F7  |  F8  |  F9  |  F10 |
+ * |------+------+------+------+------|------|------+------+------+------+------|
+ * |  F11 |  F12 |      |RGBSAI|RGBSAD|      |RGBVAI|RGBVAD|      |      |      |
+ * |------+------+------+------+------|------|------+------+------+------+------|
+ * | Reset|RGBTOG|RGBMOD|RGBHUI|RGBHUD|      | Prev | Next | Vol- | Vol+ | Play |
+ * `-------------+------+------+------|------|------+------+------+------+------'
+ *               |      | LOWER|      |      |      | RAISE|      |
+ *               `------------------------------------------------'
+ */
+[_ADJUST] =  LAYOUT(
+  KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,    _______, KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,
+  KC_F11,  KC_F12,  RGB_RMOD, RGB_SAI, RGB_SAD, _______, RGB_VAI, RGB_VAD, _______, _______, _______,
+  RESET,   RGB_TOG, RGB_MOD, RGB_HUI, RGB_HUD,  _______, KC_MPRV, KC_MNXT, KC_VOLD, KC_VOLU, KC_MPLY,
+                    _______, _______, _______,  _______, _______,  _______, _______
+)
+};
+
+bool process_record_user(uint16_t keycode, keyrecord_t *record) {
+  switch (keycode) {
+    case QWERTY:
+      if (record->event.pressed) {
+        // persistant_default_layer_set(1UL<<_QWERTY);
+        set_single_persistent_default_layer(_QWERTY);
+      }
+      return false;
+    case LOWER:
+      if (record->event.pressed) {
+        layer_on(_LOWER);
+        update_tri_layer(_LOWER, _RAISE, _ADJUST);
+      } else {
+        layer_off(_LOWER);
+        update_tri_layer(_LOWER, _RAISE, _ADJUST);
+      }
+      return false;
+    case RAISE:
+      if (record->event.pressed) {
+        layer_on(_RAISE);
+        update_tri_layer(_LOWER, _RAISE, _ADJUST);
+      } else {
+        layer_off(_RAISE);
+        update_tri_layer(_LOWER, _RAISE, _ADJUST);
+      }
+      return false;
+    case ADJUST:
+      if (record->event.pressed) {
+        layer_on(_ADJUST);
+      } else {
+        layer_off(_ADJUST);
+      }
+      return false;
+  }
+  return true;
+}
+
+void matrix_init_user(void) {
+
+}
+
+void matrix_scan_user(void) {
+
+}
+
+void led_set_user(uint8_t usb_led) {
+
+}

keyboards/halberd/keymaps/default/readme.md

@@ -0,0 +1 @@
+# The default keymap for halberd

keyboards/halberd/keymaps/right_modifiers/config.h

@@ -0,0 +1,19 @@
+/* Copyright 2019 ENDO Katsuhiro <ka2hiro@kagizaraya.jp>
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+
+// place overrides here

keyboards/halberd/keymaps/right_modifiers/keymap.c

@@ -0,0 +1,160 @@
+/* Copyright 2019 ENDO Katsuhiro <ka2hiro@kagizaraya.jp>
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include QMK_KEYBOARD_H
+
+// Defines the keycodes used by our macros in process_record_user
+enum layer_names {
+    _QWERTY,
+    _LOWER,
+    _RAISE,
+    _ADJUST,
+};
+
+// Defines the keycodes used by our macros in process_record_user
+enum custom_keycodes {
+  QWERTY = SAFE_RANGE,
+  LOWER,
+  RAISE,
+  ADJUST,
+};
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+/* Qwerty
+ *
+ * ,----------------------------------------------------------------------------.
+ * |   Q  |   W  |   E  |   R  |   T  |   Y  |   U  |   I  |   O  |   P  | BkSp |
+ * |------+------+------+------+------|------+------+------+------+------|------|
+ * |   A  |   S  |   D  |   F  |   G  |   H  |   J  |   K  |   L  |   ;  | Enter|
+ * |------+------+------+------+------|------+------+------+------+------|------|
+ * |   Z  |   X  |   C  |   V  |   B  |   N  |   M  |   ,  |   .  |   /  | Shift|
+ * `-------------+------+------+------|------+------+------+------+------+------'
+ *               | GUI  | LOWER|Ctrl/Esc|Space| RAISE| Alt | Tab  |
+ *               `------------------------------------------------'
+ */
+[_QWERTY] = LAYOUT(
+  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_BSPC,
+  KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN, KC_ENT,
+  KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH, KC_LSFT,
+                    KC_LGUI, LOWER, MT(MOD_LCTL, KC_ESC),  KC_SPC, RAISE, KC_LALT, KC_TAB
+),
+
+/* Raise
+ *
+ * ,----------------------------------------------------------------------------.
+ * |   !  |   @  |   #  |   $  |   %  |   ^  |   &  |   *  |   (  |   )  |      |
+ * |------+------+------+------+------|------+------+------+------+------|------|
+ * |  Tab |   _  |   +  |  |   |  ~   |   :  |   "  |   >  |   {  |   }  |      |
+ * |------+------+------+------+------|------+------+------+------+------|------|
+ * |  Caps|   -  |   =  |  \   |  `   |   ;  |   '  |   <  |   [  |   ]  |      |
+ * `-------------+------+------+------|------+------+------+------+------+------'
+ *               |      |      |      |      |      |      |      |
+ *               `------------------------------------------------'
+ */
+[_RAISE] = LAYOUT( 
+  KC_EXLM, KC_AT,   KC_HASH, KC_DLR,  KC_PERC, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, _______,
+  KC_TAB,  KC_UNDS, KC_PLUS, KC_PIPE, KC_TILD, KC_COLN, KC_DQUO, KC_GT,   KC_LCBR, KC_RCBR, _______,
+  KC_CAPS, KC_MINS, KC_EQL,  KC_BSLS, KC_GRV,  KC_SCLN, KC_QUOT, KC_LT,   KC_LBRC, KC_RBRC, _______,
+                    _______, _______, _______, _______, _______,  _______, _______
+),
+
+/* Lower
+ *
+ * ,----------------------------------------------------------------------------.
+ * |   1  |   2  |   3  |   4  |   5  |   6  |   7  |   8  |   9  |   0  |      |
+ * |------+------+------+------+------|------+------+------+------+------|------|
+ * |  Tab |      |      |      |Enter | Left | Down |  Up  | Right| Enter|      |
+ * |------+------+------+------+------|------+------+------+------+------|------|
+ * |  Ctrl|      |  GUI |  Alt | Del  | BkSp | PgUp | PgDn |      |      |      |
+ * `-------------+------+------+------|------+------+------+------+------+------'
+ *               |      |      |      |      |      |      |      |
+ *               `------------------------------------------------'
+ */
+[_LOWER] = LAYOUT(
+  KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    _______,
+  KC_TAB,  _______, _______, _______, KC_ENT,  KC_LEFT, KC_DOWN, KC_UP,   KC_RGHT, KC_ENT,  _______,
+  KC_LCTL, _______, KC_LGUI, KC_LALT, KC_DEL,  KC_BSPC, KC_PGUP, KC_PGDN, _______, _______, _______,
+                    _______, _______, _______, _______, _______, _______, _______
+),
+
+
+/* Adjust (Lower + Raise)
+ *
+ * ,----------------------------------------------------------------------------.
+ * |  F1  |  F2  |  F3  |  F4  |  F5  |   F6 |  F7  |  F8  |  F9  |  F10 |      |
+ * |------+------+------+------+------|------+------+------+------+------|------|
+ * |  F11 |  F12 |      |RGBSAI|RGBSAD|RGBVAI|RGBVAD|      |      |      |      |
+ * |------+------+------+------+------|------+------+------+------+------|------|
+ * | Reset|RGBTOG|RGBMOD|RGBHUI|RGBHUD| Prev | Next | Vol- | Vol+ | Play |      |
+ * `-------------+------+------+------|------+------+------+------+------+------'
+ *               |      |      |      |      |      |      |      |
+ *               `------------------------------------------------'
+ */
+[_ADJUST] =  LAYOUT(
+  KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,    KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  _______,
+  KC_F11,  KC_F12,  RGB_RMOD, RGB_SAI, RGB_SAD, RGB_VAI, RGB_VAD, _______, _______, _______, _______,
+  RESET,   RGB_TOG, RGB_MOD, RGB_HUI, RGB_HUD,  KC_MPRV, KC_MNXT, KC_VOLD, KC_VOLU, KC_MPLY, _______,
+                    _______, _______, _______,  _______, _______,  _______, _______
+)
+};
+
+bool process_record_user(uint16_t keycode, keyrecord_t *record) {
+  switch (keycode) {
+    case QWERTY:
+      if (record->event.pressed) {
+        // persistant_default_layer_set(1UL<<_QWERTY);
+        set_single_persistent_default_layer(_QWERTY);
+      }
+      return false;
+    case LOWER:
+      if (record->event.pressed) {
+        layer_on(_LOWER);
+        update_tri_layer(_LOWER, _RAISE, _ADJUST);
+      } else {
+        layer_off(_LOWER);
+        update_tri_layer(_LOWER, _RAISE, _ADJUST);
+      }
+      return false;
+    case RAISE:
+      if (record->event.pressed) {
+        layer_on(_RAISE);
+        update_tri_layer(_LOWER, _RAISE, _ADJUST);
+      } else {
+        layer_off(_RAISE);
+        update_tri_layer(_LOWER, _RAISE, _ADJUST);
+      }
+      return false;
+    case ADJUST:
+      if (record->event.pressed) {
+        layer_on(_ADJUST);
+      } else {
+        layer_off(_ADJUST);
+      }
+      return false;
+  }
+  return true;
+}
+
+void matrix_init_user(void) {
+
+}
+
+void matrix_scan_user(void) {
+
+}
+
+void led_set_user(uint8_t usb_led) {
+
+}

keyboards/halberd/keymaps/right_modifiers/readme.md

@@ -0,0 +1,2 @@
+# Modifiers on the right side.
+

keyboards/halberd/readme.md

@@ -0,0 +1,15 @@
+# Halberd
+
+![Halberd](https://i.imgur.com/QabQNPQ.jpg)
+
+40% keyboard.
+
+Keyboard Maintainer: [ka2hiro](https://github.com/ka2hiro) [@ka2hiro](https://twitter.com/ka2hiro)  
+Hardware Supported: Halberd PCB, ATMEGA32U4  
+Hardware Availability: [@kagizaraya](https://twitter.com/kagizaraya)
+
+Make example for this keyboard (after setting up your build environment):
+
+    make halberd:default:dfu
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/halberd/rules.mk

@@ -0,0 +1,80 @@
+# MCU name
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   atmega32a    bootloadHID
+BOOTLOADER = atmel-dfu
+
+
+# If you don't know the bootloader type, then you can specify the
+# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
+#   Teensy halfKay      512
+#   Teensy++ halfKay    1024
+#   Atmel DFU loader    4096
+#   LUFA bootloader     4096
+#   USBaspLoader        2048
+# OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE = lite     # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = no       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = no         # Console for debug(+400)
+COMMAND_ENABLE = no         # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE = no            # USB Nkey Rollover
+BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality on B7 by default
+RGBLIGHT_ENABLE = yes        # Enable keyboard RGB underglow
+MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no           # Audio output on port C6
+FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
+HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)

keyboards/handwired/daishi/config.h

@@ -0,0 +1,61 @@
+/*
+Copyright 2019 Crokto
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0x6D6D
+#define PRODUCT_ID      0x0001
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    MetaMechs
+#define PRODUCT         Daishi
+#define DESCRIPTION     Compact Battlecruiser
+
+/* key matrix size */
+#define MATRIX_ROWS 7
+#define MATRIX_COLS 18
+
+/*
+ * Keyboard Matrix Assignments
+ *
+ * Change this to how you wired your keyboard
+ * COLS: AVR pins used for columns, left to right
+ * ROWS: AVR pins used for rows, top to bottom
+ * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
+ *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
+ *
+*/
+#define MATRIX_ROW_PINS { D6, D7, E0, E1, C0, C1, C2 }
+#define MATRIX_COL_PINS { E6, E7, E3, B0, B1, B2, A6, A5, A4, A3, A2, A1, A0, F7, F6, F5, F4, F3 }
+#define UNUSED_PINS
+
+/* COL2ROW, ROW2COL, or CUSTOM_MATRIX */
+#define DIODE_DIRECTION COL2ROW
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCING_DELAY 5
+
+/* Set up rotary encoder */
+#define NUMBER_OF_ENCODERS 1
+#define ENCODERS_PAD_A { F1 }
+#define ENCODERS_PAD_B { F0 }
+#define ENCODER_RESOLUTION 2
+
+/* Set delay for tap_code on rotary encoder */
+#define TAP_CODE_DELAY 10

keyboards/handwired/daishi/daishi.c

@@ -0,0 +1,22 @@
+#include "daishi.h"
+
+void matrix_init_kb(void) {	
+  // put your keyboard start-up code here
+  // runs once when the firmware starts up
+
+  matrix_init_user();
+}
+
+void matrix_scan_kb(void) {
+  // put your looping keyboard code here
+  // runs every cycle (a lot)
+
+  matrix_scan_user();
+}
+
+bool process_record_kb(uint16_t keycode, keyrecord_t *record) {
+  // put your per-action keyboard code here
+  // runs for every action, just before processing by the firmware
+
+  return process_record_user(keycode, record);
+}

keyboards/handwired/daishi/daishi.h

@@ -0,0 +1,25 @@
+#pragma once
+
+#include "quantum.h"
+
+#define encoder_update(clockwise) encoder_update_user(uint8_t index, clockwise)
+
+// The first section contains all of the arguments
+// The second converts the arguments into a two-dimensional array
+#define LAYOUT( \
+    K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, K0E, K0F, K0G, K0H, \
+    K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, K1E, K1F, K1G, K1H, \
+    K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, K2C, K2D, K2E, K2F, K2G, K2H, \
+    K30, K31, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, K3C, K3D, K3E, K3F, K3G, K3H, \
+    K40, K41, K42, K43, K44, K45, K46, K47, K48, K49, K4A, K4B, K4C,      K4E, K4F, K4G, K4H, \
+    K50, K51, K52, K53, K54, K55, K56, K57, K58, K59, K5A, K5B,      K5D, K5E, K5F, K5G, K5H, \
+    K60, K61, K62,           K65,                K69, K6A,      K6C, K6D, K6E, K6F, K6G       \
+){ \
+    { K00, K01, K02, K03,   K04,   K05, K06,   K07,   K08,   K09, K0A, K0B,   K0C,   K0D,   K0E, K0F, K0G, K0H   }, \
+    { K10, K11, K12, K13,   K14,   K15, K16,   K17,   K18,   K19, K1A, K1B,   K1C,   K1D,   K1E, K1F, K1G, K1H   }, \
+    { K20, K21, K22, K23,   K24,   K25, K26,   K27,   K28,   K29, K2A, K2B,   K2C,   K2D,   K2E, K2F, K2G, K2H   }, \
+    { K30, K31, K32, K33,   K34,   K35, K36,   K37,   K38,   K39, K3A, K3B,   K3C,   K3D,   K3E, K3F, K3G, K3H   }, \
+    { K40, K41, K42, K43,   K44,   K45, K46,   K47,   K48,   K49, K4A, K4B,   K4C,   KC_NO, K4E, K4F, K4G, K4H   }, \
+    { K50, K51, K52, K53,   K54,   K55, K56,   K57,   K58,   K59, K5A, K5B,   KC_NO, K5D,   K5E, K5F, K5G, K5H   }, \
+    { K60, K61, K62, KC_NO, KC_NO, K65, KC_NO, KC_NO, KC_NO, K69, K6A, KC_NO, K6C,   K6D,   K6E, K6F, K6G, KC_NO }  \
+}

keyboards/handwired/daishi/keymaps/default/keymap.c

@@ -0,0 +1,124 @@
+#include QMK_KEYBOARD_H
+
+// Layer shorthand
+#define _QW 0
+#define _FN 1
+
+enum custom_keycodes {
+    M_EXAMPLE1 = SAFE_RANGE,
+	M_EXAMPLE2,
+	DYNAMIC_MACRO_RANGE,
+};
+
+#include "dynamic_macro.h"
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+/* QWERTY
+ * .-----------------------------------------------------------------------------------------------------------------------------------------------------------------.
+ * | ESC    |        |        |        |        |        |        |        |        |        | DM1    | DM2    | DMSTOP | PRINT  | SCROLL | PAUSE  | FN     | VOL    |
+ * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------------------------------------------|
+ * | F1     | F2     | F3     | F4     | F5     | F6     | F7     | F8     | F9     | F10    | F11    | F12    | DEL    | HOME   | PGUP   | END    | INS    | NUM    |
+ * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------------------------------------------|
+ * | `      | 1      | 2      | 3      | 4      | 5      | 6      | 7      | 8      | 9      | 0      | -      | =      | BACK   | PGDN   | /      | *      | -      |
+ * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------------------------------------------|
+ * | TAB    | Q      | W      | E      | R      | T      | Y      | U      | I      | O      | P      | [      | ]      | \      | 7      | 8      | 9      | +      |
+ * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------------------------------------------|
+ * | CAPS   | A      | S      | D      | F      | G      | H      | J      | K      | L      | ;      | '      | ENTER  |        | 4      | 5      | 6      | =      |
+ * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------------------------------------------|
+ * | LSHIFT | Z      | X      | C      | V      | B      | N      | M      | ,      | .      | /      | SHIFT  |        | UP     | 1	  | 2      | 3      | ENTER  |
+ * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------------------------------------------|
+ * | LCTRL  | LGUI   | LALT   |        |        | SPACE  |        |        |        | RALT   | RCTRL  |        | LEFT   | DOWN   | RIGHT  | 0      | .      |        |
+ * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------------------------------------------'
+ */
+
+ [_QW] = LAYOUT( /* QWERTY */
+  KC_ESC , _______, _______, _______, _______, _______, _______, _______, _______, _______,DYN_MACRO_PLAY1,DYN_MACRO_PLAY2,DYN_REC_STOP, KC_PSCR, KC_SLCK, KC_PAUS, MO(_FN), KC_MUTE,
+  KC_F1  , KC_F2  , KC_F3  , KC_F4  , KC_F5  , KC_F6  , KC_F7  , KC_F8  , KC_F9  , KC_F10 , KC_F11 , KC_F12 , KC_DEL , KC_HOME, KC_PGUP, KC_END , KC_INS , KC_NLCK,
+  KC_GRV , KC_1   , KC_2   , KC_3   , KC_4   , KC_5   , KC_6   , KC_7   , KC_8   , KC_9   , KC_0   , KC_MINS, KC_EQL , KC_BSPC, KC_PGDN, KC_PSLS, KC_PAST, KC_PMNS,
+  KC_TAB , KC_Q   , KC_W   , KC_E   , KC_R   , KC_T   , KC_Y   , KC_U   , KC_I   , KC_O   , KC_P   , KC_LBRC, KC_RBRC, KC_BSLS, KC_P7  , KC_P8  , KC_P9  , KC_PPLS,
+  KC_CAPS, KC_A   , KC_S   , KC_D   , KC_F   , KC_G   , KC_H   , KC_J   , KC_K   , KC_L   , KC_SCLN, KC_QUOT, KC_ENT ,          KC_P4  , KC_P5  , KC_P6  , KC_EQL ,
+  KC_LSFT, KC_Z   , KC_X   , KC_C   , KC_V   , KC_B   , KC_N   , KC_M   , KC_COMM, KC_DOT , KC_SLSH, KC_RSFT,          KC_UP  , KC_P1  , KC_P2  , KC_P3  , KC_PENT,
+  KC_LCTL, KC_LGUI, KC_LALT,                   KC_SPC ,                            KC_RALT, KC_RCTL,          KC_LEFT, KC_DOWN, KC_RGHT, KC_P0  , KC_PDOT         
+ ),
+
+/* FN
+ * .-----------------------------------------------------------------------------------------------------------------------------------------------------------------.
+ * | RESET  | F13    | F14    | F15    | f16    | f17    | f18    | F19    | F20    | F21    | DM1 R  | DM2 R  | DMSTOP |        |        |        | FN     | DEBUG  |
+ * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------------------------------------------|
+ * |        |        |        |        |        |        |        |        |        |        |        |        |        |        |        |        |        |        |
+ * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------------------------------------------|
+ * |        |        |        |        |        |        |        |        |        |        |        |        |        |        |        |        |        |        |
+ * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------------------------------------------|
+ * |        |        |        |        |        |        |        |        |        |        |        |        |        |        |        |        |        |        |
+ * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------------------------------------------|
+ * |        |        |        |        |        |        |        |        |        |        |        |        |        |        |        |        |        |        |
+ * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------------------------------------------|
+ * |        |        |        |        |        |        |        |        |        |        |        |        |        |        |        |        |        |        |
+ * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------------------------------------------|
+ * |        |        |        |        |        |        |        |        |        |        |        |        |        |        |        |        |        |        |
+ * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------------------------------------------'
+ */
+ 
+ [_FN] = LAYOUT( /* Function */
+  RESET  , KC_F13 , KC_F14 , KC_F15 , KC_F16 , KC_F17 , KC_F18 , KC_F19 , KC_F20 , KC_F21 ,DYN_REC_START1,DYN_REC_START2,DYN_REC_STOP, _______, _______, _______, MO(_FN), DEBUG,
+  _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,
+  _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,
+  _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,
+  _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,          _______, _______, _______, _______,
+  _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,          _______, _______, _______, _______, _______,
+  _______, _______,  _______,                  _______,                            _______, _______,          _______, _______, _______, _______, _______         
+ )
+};
+
+bool process_record_user(uint16_t keycode, keyrecord_t *record) {
+	if (!process_record_dynamic_macro(keycode, record)) {
+        return false;
+    }
+    if (record->event.pressed) {
+        switch(keycode) {
+            case M_EXAMPLE1:
+                SEND_STRING("This is an example macro!"SS_TAP(X_ENTER)); //prints "This is an example macro!" and hits Enter
+                return false; 
+            case M_EXAMPLE2:
+                SEND_STRING("This is a another example!"SS_TAP(X_ENTER)); //prints "This is a another example!" and hits Enter
+                return false; 
+        }
+    }
+    return true;
+};
+
+void encoder_update(bool clockwise) {
+ if (clockwise) {
+  tap_code(KC_VOLU);
+ } else {
+  tap_code(KC_VOLD);
+ }
+}
+	
+void matrix_init_user(void) {
+  // Call the keymap level matrix init.
+
+  // Set our LED pins as output
+  setPinOutput(C4);
+  setPinOutput(C5);
+  setPinOutput(C6);
+}
+
+void led_set_kb(uint8_t usb_led) {
+    if (IS_LED_OFF(usb_led, USB_LED_NUM_LOCK)) {
+        writePinLow(C4);
+    } else {
+        writePinHigh(C4);
+    }
+    if (IS_LED_OFF(usb_led, USB_LED_CAPS_LOCK)) {
+        writePinLow(C5);
+    } else {
+        writePinHigh(C5);
+    }
+    if (IS_LED_OFF(usb_led, USB_LED_SCROLL_LOCK)) {
+        writePinLow(C6);
+    } else {
+        writePinHigh(C6);
+    }
+}

keyboards/handwired/daishi/keymaps/default/readme.md

@@ -0,0 +1,5 @@
+# Default Daishi Layout
+
+![Daishi Layout Image](https://i.imgur.com/fuJZGmw.png)
+
+This is the default layout that comes on the Daishi. For more information on the design of this layout, check out [kb.metamechs.com](http://kb.metamechs.com/daishi/).

keyboards/handwired/daishi/readme.md

@@ -0,0 +1,15 @@
+# Daishi
+
+![Daishi](http://kb.metamechs.com/wp-content/uploads/2019/03/IMG_20190325_113405-e1553610532162-1024x709.jpg)
+
+A compact battlecruiser using the CBC1 PCB. [More info on kb.metamechs.com](http://kb.metamechs.com/daishi/)
+
+Keyboard Maintainer: [Crokto](https://github.com/Croktopus/)  
+Hardware Supported: CBC1 PCB  
+Hardware Availability: [kb.metamechs.com](http://kb.metamechs.com/daishi/get-your-own-daishi/)
+
+Make example for this keyboard (after setting up your build environment):
+
+    make handwired/daishi:default
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/handwired/daishi/rules.mk

@@ -0,0 +1,66 @@
+# MCU name
+MCU = at90usb1286
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+BOOTLOADER = atmel-dfu
+
+# QMK Build Options
+#   change to "no" to disable the options, or define them in the Makefile in 
+#   the appropriate keymap folder that will get included automatically
+#
+BOOTMAGIC_ENABLE = no       # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = no        # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = yes        # Console for debug(+400)
+COMMAND_ENABLE = no         # Commands for debug and configuration
+NKRO_ENABLE = yes           # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality
+MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
+AUDIO_ENABLE = no           # Audio output on port C6
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+RGBLIGHT_ENABLE = no        # Enable WS2812 RGB underlight.  Do not enable this with audio at the same time.
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+ENCODER_ENABLE = yes		# Add rotary encoder support

keyboards/handwired/frenchdev/matrix.c

@@ -5,11 +5,6 @@ The "column" and "row" in here actually refers to the opposite on the keyboard
 see definition of KEYMAP in v1.h, the grid is transposed so that a "row" in here is actually a "column" on the physical keyboard
 Nicolas
 
-Note for ErgoDox EZ customizers: Here be dragons!
-This is not a file you want to be messing with.
-All of the interesting stuff for you is under keymaps/ :)
-Love, Erez
-
 Copyright 2013 Oleg Kostyuk <cub.uanic@gmail.com>
 Copyright 2013 Nicolas Poirey <nicolas.poirey@gmail.com>