Single Color Band scrolling left to right effects (#5867)

* Adding an AUDIO_CLICKY_DELAY_DURATION configurable value to the AUDIO_CLICKY feature.

* Tweaking my community keymap to work better with my rev 4 planck.

docs/config_options.md

@@ -171,6 +171,8 @@ If you define these options you will enable the associated feature, which may in
   * how long for the Combo keys to be detected. Defaults to `TAPPING_TERM` if not defined.
 * `#define TAP_CODE_DELAY 100`
   * Sets the delay between `register_code` and `unregister_code`, if you're having issues with it registering properly (common on VUSB boards). The value is in milliseconds.
+* `#define TAP_HOLD_CAPS_DELAY 200`
+  * Sets the delay for Tap Hold keys (`LT`, `MT`) when using `KC_CAPSLOCK` keycode, as this has some special handling on MacOS.  The value is in milliseconds, and defaults to 200ms if not defined. 
 
 ## RGB Light Configuration
 

docs/feature_audio.md

@@ -175,8 +175,9 @@ You can configure the default, min and max frequencies, the stepping and built i
 | `AUDIO_CLICKY_FREQ_DEFAULT` | 440.0f | Sets the default/starting audio frequency for the clicky sounds. |
 | `AUDIO_CLICKY_FREQ_MIN` | 65.0f | Sets the lowest frequency (under 60f are a bit buggy). |
 | `AUDIO_CLICKY_FREQ_MAX` | 1500.0f | Sets the the highest frequency. Too high may result in coworkers attacking you. |
-| `AUDIO_CLICKY_FREQ_FACTOR` | 1.18921f| Sets the stepping of UP/DOWN key codes. |
+| `AUDIO_CLICKY_FREQ_FACTOR` | 1.18921f| Sets the stepping of UP/DOWN key codes.  This is a multiplicative factor.  The default steps the frequency up/down by a musical minor third.  |
 | `AUDIO_CLICKY_FREQ_RANDOMNESS`     |  0.05f |  Sets a factor of randomness for the clicks, Setting this to `0f` will make each click identical, and `1.0f` will make this sound much like the 90's computer screen scrolling/typing effect. | 
+| `AUDIO_CLICKY_DELAY_DURATION` | 1 | An integer note duration where 1 is 1/16th of the tempo, or a sixty-fourth note (see `quantum/audio/musical_notes.h` for implementation details). The main clicky effect will be delayed by this duration.  Adjusting this to values around 6-12 will help compensate for loud switches. |
 
 
 

docs/feature_rgb_matrix.md

@@ -194,6 +194,8 @@ enum rgb_matrix_effects {
     RGB_MATRIX_ALPHAS_MODS,         // Static dual hue, speed is hue for secondary hue
     RGB_MATRIX_GRADIENT_UP_DOWN,    // Static gradient top to bottom, speed controls how much gradient changes
     RGB_MATRIX_BREATHING,           // Single hue brightness cycling animation
+    RGB_MATRIX_BAND_SAT,        // Single hue band fading saturation scrolling left to right
+    RGB_MATRIX_BAND_VAL,        // Single hue band fading brightness scrolling left to right
     RGB_MATRIX_CYCLE_ALL,           // Full keyboard solid hue cycling through full gradient
     RGB_MATRIX_CYCLE_LEFT_RIGHT,    // Full gradient scrolling left to right
     RGB_MATRIX_CYCLE_UP_DOWN,       // Full gradient scrolling top to bottom
@@ -235,6 +237,8 @@ You can disable a single effect by defining `DISABLE_[EFFECT_NAME]` in your `con
 |`#define DISABLE_RGB_MATRIX_ALPHAS_MODS`               |Disables `RGB_MATRIX_ALPHAS_MODS`              |
 |`#define DISABLE_RGB_MATRIX_GRADIENT_UP_DOWN`          |Disables `RGB_MATRIX_GRADIENT_UP_DOWN`         |
 |`#define DISABLE_RGB_MATRIX_BREATHING`                 |Disables `RGB_MATRIX_BREATHING`                |
+|`#define DISABLE_RGB_MATRIX_BAND_SAT`                  |Disables `RGB_MATRIX_BAND_SAT`                 |
+|`#define DISABLE_RGB_MATRIX_BAND_VAL`                  |Disables `RGB_MATRIX_BAND_VAL`                 |
 |`#define DISABLE_RGB_MATRIX_CYCLE_ALL`                 |Disables `RGB_MATRIX_CYCLE_ALL`                |
 |`#define DISABLE_RGB_MATRIX_CYCLE_LEFT_RIGHT`          |Disables `RGB_MATRIX_CYCLE_LEFT_RIGHT`         |
 |`#define DISABLE_RGB_MATRIX_CYCLE_UP_DOWN`             |Disables `RGB_MATRIX_CYCLE_UP_DOWN`            |

docs/feature_rgblight.md

@@ -129,7 +129,7 @@ The following options are used to tweak the various animations:
 |`RGBLIGHT_EFFECT_KNIGHT_LED_NUM`    |`RGBLED_NUM` |The number of LEDs to have the "Knight" animation travel                             |
 |`RGBLIGHT_EFFECT_KNIGHT_LENGTH`     |`3`          |The number of LEDs to light up for the "Knight" animation                            |
 |`RGBLIGHT_EFFECT_KNIGHT_OFFSET`     |`0`          |The number of LEDs to start the "Knight" animation from the start of the strip by    |
-|`RGBLIGHT_RAINBOW_SWIRL_RANGE`      |`360`        |Range adjustment for the rainbow swirl effect to get different swirls                |
+|`RGBLIGHT_RAINBOW_SWIRL_RANGE`      |`255`        |Range adjustment for the rainbow swirl effect to get different swirls                |
 |`RGBLIGHT_EFFECT_SNAKE_LENGTH`      |`4`          |The number of LEDs to light up for the "Snake" animation                             |
 
 ### Example Usage to Reduce Memory Footprint
@@ -176,44 +176,100 @@ const uint8_t RGBLED_GRADIENT_RANGES[] PROGMEM = {255, 170, 127, 85, 64};
 
 If you need to change your RGB lighting in code, for example in a macro to change the color whenever you switch layers, QMK provides a set of functions to assist you. See [`rgblight.h`](https://github.com/qmk/qmk_firmware/blob/master/quantum/rgblight.h) for the full list, but the most commonly used functions include:
 
-|Function                                    |Description                                                                                                                                                   |
-|--------------------------------------------|--------------------------------------------------------------------------------------------------------------------------------------------------------------|
-|`rgblight_enable()`                         |Turn LEDs on, based on their previous state                                                                                                                   |
-|`rgblight_enable_noeeprom()`                |Turn LEDs on, based on their previous state (not written to EEPROM)                                                                                           |
-|`rgblight_disable()`                        |Turn LEDs off                                                                                                                                                 |
-|`rgblight_disable_noeeprom()`               |Turn LEDs off (not written to EEPROM)                                                                                                                         |
-|`rgblight_mode(x)`                          |Set the mode, if RGB animations are enabled                                                                                                                   |
-|`rgblight_mode_noeeprom(x)`                 |Set the mode, if RGB animations are enabled (not written to EEPROM)                                                                                           |
-|`rgblight_setrgb(r, g, b)`                  |Set all LEDs to the given RGB value where `r`/`g`/`b` are between 0 and 255 (not written to EEPROM)                                                           |
-|`rgblight_setrgb_at(r, g, b, led)`          |Set a single LED to the given RGB value, where `r`/`g`/`b` are between 0 and 255 and `led` is between 0 and `RGBLED_NUM` (not written to EEPROM)              |
+### Utility Functions
+|Function                                    |Description                                                        |
+|--------------------------------------------|-------------------------------------------------------------------|
+|`sethsv(hue, sat, val, ledbuf)`             |Set ledbuf to the given HSV value                                  |
+|`sethsv_raw(hue, sat, val, ledbuf)`         |Set ledbuf to the given HSV value without RGBLIGHT_LIMIT_VAL check |
+|`setrgb(r, g, b, ledbuf)`                   |Set ledbuf to the given RGB value where `r`/`g`/`b`                |
+
+### Low level Functions
+|Function                                    |Description                                |
+|--------------------------------------------|-------------------------------------------|
+|`rgblight_set()`                            |Flash out led buffers to LEDs              |
+|`rgblight_set_clipping_range(pos, num)`     |Set clipping Range. see [Clipping Range](#clipping-range) |
+
+Example:
+```c
+sethsv(HSV_WHITE, (LED_TYPE *)&led[0]); // led 0
+sethsv(HSV_RED,   (LED_TYPE *)&led[1]); // led 1
+sethsv(HSV_GREEN, (LED_TYPE *)&led[2]); // led 2
+rgblight_set(); // Utility functions do not call rgblight_set() automatically, so they need to be called explicitly.
+```
+
+### Effects and Animations Functions
+#### effect range setting
+|Function                                    |Description       |
+|--------------------------------------------|------------------|
+|`rgblight_set_effect_range(pos, num)`       |Set Effects Range |
+
+#### direct operation
+|Function                                    |Description  |
+|--------------------------------------------|-------------|
+|`rgblight_setrgb_at(r, g, b, index)`          |Set a single LED to the given RGB value, where `r`/`g`/`b` are between 0 and 255 and `index` is between 0 and `RGBLED_NUM` (not written to EEPROM) |
+|`rgblight_sethsv_at(h, s, v, index)`          |Set a single LED to the given HSV value, where `h`/`s`/`v` are between 0 and 255, and `index` is between 0 and `RGBLED_NUM` (not written to EEPROM) |
 |`rgblight_setrgb_range(r, g, b, start, end)`|Set a continuous range of LEDs to the given RGB value, where `r`/`g`/`b` are between 0 and 255 and `start`(included) and `stop`(excluded) are between 0 and `RGBLED_NUM` (not written to EEPROM)|
-|`rgblight_setrgb_master(r, g, b)`           |Set the LEDs on the master side  to the given RGB value, where `r`/`g`/`b` are between 0 and 255 (not written to EEPROM)                                      |
-|`rgblight_setrgb_slave(r, g, b)`            |Set the LEDs on the slave side  to the given RGB value, where `r`/`g`/`b` are between 0 and 255 (not written to EEPROM)                                       |
-|`rgblight_sethsv(h, s, v)`                  |Set all LEDs to the given HSV value where `h` is between 0 and 360 and `s`/`v` are between 0 and 255                                                          |
-|`rgblight_sethsv_noeeprom(h, s, v)`         |Set all LEDs to the given HSV value where `h` is between 0 and 360 and `s`/`v` are between 0 and 255 (not written to EEPROM)                                  |
-|`rgblight_sethsv_at(h, s, v, led)`          |Set a single LED to the given HSV value, where `h` is between 0 and 360, `s`/`v` are between 0 and 255, and `led` is between 0 and `RGBLED_NUM` (not written to EEPROM)|
-|`rgblight_sethsv_range(h, s, v, start, end)`|Set a continuous range of LEDs to the given HSV value, where `h` is between 0 and 360, `s`/`v` are between 0 and 255, and `start`(included) and `stop`(excluded) are between 0 and `RGBLED_NUM` (not written to EEPROM)|
-|`rgblight_sethsv_master(h, s, v)`           |Set the LEDs on the master side to the given HSV value, where `h` is between 0 and 360, `s`/`v` are between 0 and 255 (not written to EEPROM)                 |
-|`rgblight_sethsv_slave(h, s, v)`            |Set the LEDs on the slave side to the given HSV value, where `h` is between 0 and 360, `s`/`v` are between 0 and 255 (not written to EEPROM)                  |
-|`rgblight_toggle()`                         |Toggle all LEDs between on and off                                                                                                                            |
-|`rgblight_toggle_noeeprom()`                |Toggle all LEDs between on and off (not written to EEPROM)                                                                                                    |
-|`rgblight_step()`                           |Change the mode to the next RGB animation in the list of enabled RGB animations                                                                               |
-|`rgblight_step_noeeprom()`                  |Change the mode to the next RGB animation in the list of enabled RGB animations (not written to EEPROM)                                                       |
-|`rgblight_step_reverse()`                   |Change the mode to the previous RGB animation in the list of enabled RGB animations                                                                           |
-|`rgblight_step_reverse_noeeprom()`          |Change the mode to the previous RGB animation in the list of enabled RGB animations (not written to EEPROM)                                                   |
-|`rgblight_increase_hue()`                   |Increase the hue for all LEDs. This wraps around at maximum hue                                                                                               |
-|`rgblight_increase_hue_noeeprom()`          |Increase the hue for all LEDs. This wraps around at maximum hue (not written to EEPROM)                                                                       |
-|`rgblight_decrease_hue()`                   |Decrease the hue for all LEDs. This wraps around at minimum hue                                                                                               |
-|`rgblight_decrease_hue_noeeprom()`          |Decrease the hue for all LEDs. This wraps around at minimum hue (not written to EEPROM)                                                                       |
-|`rgblight_increase_sat()`                   |Increase the saturation for all LEDs. This wraps around at maximum saturation                                                                                 |
-|`rgblight_increase_sat_noeeprom()`          |Increase the saturation for all LEDs. This wraps around at maximum saturation (not written to EEPROM)                                                         |
-|`rgblight_decrease_sat()`                   |Decrease the saturation for all LEDs. This wraps around at minimum saturation                                                                                 |
-|`rgblight_decrease_sat_noeeprom()`          |Decrease the saturation for all LEDs. This wraps around at minimum saturation (not written to EEPROM)                                                         |
-|`rgblight_increase_val()`                   |Increase the value for all LEDs. This wraps around at maximum value                                                                                           |
-|`rgblight_increase_val_noeeprom()`          |Increase the value for all LEDs. This wraps around at maximum value (not written to EEPROM)                                                                   |
-|`rgblight_decrease_val()`                   |Decrease the value for all LEDs. This wraps around at minimum value                                                                                           |
-|`rgblight_decrease_val_noeeprom()`          |Decrease the value for all LEDs. This wraps around at minimum value (not written to EEPROM)                                                                   |
-|`rgblight_set_clipping_range(pos, num)`     |Set clipping Range                                                                                                                                            |
+|`rgblight_sethsv_range(h, s, v, start, end)`|Set a continuous range of LEDs to the given HSV value, where `h`/`s`/`v` are between 0 and 255, and `start`(included) and `stop`(excluded) are between 0 and `RGBLED_NUM` (not written to EEPROM)|
+|`rgblight_setrgb(r, g, b)`                  |Set effect range LEDs to the given RGB value where `r`/`g`/`b` are between 0 and 255 (not written to EEPROM) |
+|`rgblight_setrgb_master(r, g, b)`           |Set the LEDs on the master side  to the given RGB value, where `r`/`g`/`b` are between 0 and 255 (not written to EEPROM) |
+|`rgblight_setrgb_slave(r, g, b)`            |Set the LEDs on the slave side  to the given RGB value, where `r`/`g`/`b` are between 0 and 255 (not written to EEPROM) |
+|`rgblight_sethsv_master(h, s, v)`           |Set the LEDs on the master side to the given HSV value, where `h`/`s`/`v` are between 0 and 255 (not written to EEPROM) |
+|`rgblight_sethsv_slave(h, s, v)`            |Set the LEDs on the slave side to the given HSV value, where `h`/`s`/`v` are between 0 and 255 (not written to EEPROM) |
+
+Example:
+```c
+rgblight_sethsv(HSV_WHITE, 0); // led 0
+rgblight_sethsv(HSV_RED,   1); // led 1
+rgblight_sethsv(HSV_GREEN, 2); // led 2
+// The above functions automatically calls rgblight_set(), so there is no need to call it explicitly.
+// Note that it is inefficient to call repeatedly.
+```
+
+#### effect mode change
+|Function                                    |Description  |
+|--------------------------------------------|-------------|
+|`rgblight_mode(x)`                          |Set the mode, if RGB animations are enabled |
+|`rgblight_mode_noeeprom(x)`                 |Set the mode, if RGB animations are enabled (not written to EEPROM) |
+|`rgblight_step()`                           |Change the mode to the next RGB animation in the list of enabled RGB animations |
+|`rgblight_step_noeeprom()`                  |Change the mode to the next RGB animation in the list of enabled RGB animations (not written to EEPROM) |
+|`rgblight_step_reverse()`                   |Change the mode to the previous RGB animation in the list of enabled RGB animations |
+|`rgblight_step_reverse_noeeprom()`          |Change the mode to the previous RGB animation in the list of enabled RGB animations (not written to EEPROM) |
+
+#### effects mode disable/enable
+|Function                                    |Description  |
+|--------------------------------------------|-------------|
+|`rgblight_toggle()`                         |Toggle effect range LEDs between on and off |
+|`rgblight_toggle_noeeprom()`                |Toggle effect range LEDs between on and off (not written to EEPROM) |
+|`rgblight_enable()`                         |Turn effect range LEDs on, based on their previous state |
+|`rgblight_enable_noeeprom()`                |Turn effect range LEDs on, based on their previous state (not written to EEPROM) |
+|`rgblight_disable()`                        |Turn effect range LEDs off |
+|`rgblight_disable_noeeprom()`               |Turn effect range LEDs off (not written to EEPROM) |
+
+#### hue, sat, val change
+|Function                                    |Description  |
+|--------------------------------------------|-------------|
+|`rgblight_increase_hue()`                   |Increase the hue for effect range LEDs. This wraps around at maximum hue |
+|`rgblight_increase_hue_noeeprom()`          |Increase the hue for effect range LEDs. This wraps around at maximum hue (not written to EEPROM) |
+|`rgblight_decrease_hue()`                   |Decrease the hue for effect range LEDs. This wraps around at minimum hue |
+|`rgblight_decrease_hue_noeeprom()`          |Decrease the hue for effect range LEDs. This wraps around at minimum hue (not written to EEPROM) |
+|`rgblight_increase_sat()`                   |Increase the saturation for effect range LEDs. This wraps around at maximum saturation |
+|`rgblight_increase_sat_noeeprom()`          |Increase the saturation for effect range LEDs. This wraps around at maximum saturation (not written to EEPROM) |
+|`rgblight_decrease_sat()`                   |Decrease the saturation for effect range LEDs. This wraps around at minimum saturation |
+|`rgblight_decrease_sat_noeeprom()`          |Decrease the saturation for effect range LEDs. This wraps around at minimum saturation (not written to EEPROM) |
+|`rgblight_increase_val()`                   |Increase the value for effect range LEDs. This wraps around at maximum value |
+|`rgblight_increase_val_noeeprom()`          |Increase the value for effect range LEDs. This wraps around at maximum value (not written to EEPROM) |
+|`rgblight_decrease_val()`                   |Decrease the value for effect range LEDs. This wraps around at minimum value |
+|`rgblight_decrease_val_noeeprom()`          |Decrease the value for effect range LEDs. This wraps around at minimum value (not written to EEPROM) |
+|`rgblight_sethsv(h, s, v)`                  |Set effect range LEDs to the given HSV value where `h`/`s`/`v` are between 0 and 255 |
+|`rgblight_sethsv_noeeprom(h, s, v)`         |Set effect range LEDs to the given HSV value where `h`/`s`/`v` are between 0 and 255 (not written to EEPROM) |
+
+#### query
+|Function               |Description      |
+|-----------------------|-----------------|
+|`rgblight_get_mode()`  |Get current mode |
+|`rgblight_get_hue()`   |Get current hue  |
+|`rgblight_get_sat()`   |Get current sat  |
+|`rgblight_get_val()`   |Get current val  |
 
 ## Colors
 
@@ -324,4 +380,6 @@ In addition to setting the Clipping Range, you can use `RGBLIGHT_LED_MAP` togeth
 ```
 <img src="https://user-images.githubusercontent.com/2170248/55743747-119e4c00-5a6e-11e9-91e5-013203ffae8a.JPG" alt="clip mapped" width="70%"/>
 
+## Hardware Modification
+
 If your keyboard lacks onboard underglow LEDs, you may often be able to solder on an RGB LED strip yourself. You will need to find an unused pin to wire to the data pin of your LED strip. Some keyboards may break out unused pins from the MCU to make soldering easier. The other two pins, VCC and GND, must also be connected to the appropriate power pins.

docs/feature_userspace.md

@@ -110,7 +110,7 @@ QMK has a bunch of [functions](custom_quantum_functions.md) that have [`_quantum
 However, you can actually add support for keymap version, so that you can use it in both your userspace and your keymap! 
 
 
-For instance, lets looks at the `layer_state_set_user` function.  Lets enable the [Tri Layer State](ref_functions.md#olkb-tri-layers) functionalitly to all of our boards, and then still have your `keymap.c` still able to use this functionality. 
+For instance, let's look at the `layer_state_set_user()` function.  You can enable the [Tri Layer State](ref_functions.md#olkb-tri-layers) functionality on all of your boards, while also retaining the Tri Layer functionality in your `keymap.c` files. 
 
 In your `<name.c>` file, you'd want to add this: 
 ```c

drivers/issi/is31fl3733.c

@@ -75,10 +75,10 @@ uint8_t g_twi_transfer_buffer[20];
 // buffers and the transfers in IS31FL3733_write_pwm_buffer() but it's
 // probably not worth the extra complexity.
 uint8_t g_pwm_buffer[DRIVER_COUNT][192];
-bool g_pwm_buffer_update_required = false;
+bool g_pwm_buffer_update_required[DRIVER_COUNT] = { false };
 
 uint8_t g_led_control_registers[DRIVER_COUNT][24] = { { 0 }, { 0 } };
-bool g_led_control_registers_update_required = false;
+bool g_led_control_registers_update_required[DRIVER_COUNT] = { false };
 
 void IS31FL3733_write_register( uint8_t addr, uint8_t reg, uint8_t data )
 {
@@ -123,12 +123,13 @@ void IS31FL3733_write_pwm_buffer( uint8_t addr, uint8_t *pwm_buffer )
     }
 }
 
-void IS31FL3733_init( uint8_t addr )
+void IS31FL3733_init( uint8_t addr, uint8_t sync)
 {
     // In order to avoid the LEDs being driven with garbage data
     // in the LED driver's PWM registers, shutdown is enabled last.
     // Set up the mode and other settings, clear the PWM registers,
     // then disable software shutdown.
+    // Sync is passed so set it according to the datasheet.
 
     // Unlock the command register.
     IS31FL3733_write_register( addr, ISSI_COMMANDREGISTER_WRITELOCK, 0xC5 );
@@ -161,7 +162,7 @@ void IS31FL3733_init( uint8_t addr )
     // Set global current to maximum.
     IS31FL3733_write_register( addr, ISSI_REG_GLOBALCURRENT, 0xFF );
     // Disable software shutdown.
-    IS31FL3733_write_register( addr, ISSI_REG_CONFIGURATION, 0x01 );
+    IS31FL3733_write_register( addr, ISSI_REG_CONFIGURATION, (sync << 6) | 0x01 );
 
     // Wait 10ms to ensure the device has woken up.
     #ifdef __AVR__
@@ -179,7 +180,7 @@ void IS31FL3733_set_color( int index, uint8_t red, uint8_t green, uint8_t blue )
         g_pwm_buffer[led.driver][led.r] = red;
         g_pwm_buffer[led.driver][led.g] = green;
         g_pwm_buffer[led.driver][led.b] = blue;
-        g_pwm_buffer_update_required = true;
+        g_pwm_buffer_update_required[led.driver] = true;
     }
 }
 
@@ -218,35 +219,34 @@ void IS31FL3733_set_led_control_register( uint8_t index, bool red, bool green, b
         g_led_control_registers[led.driver][control_register_b] &= ~(1 << bit_b);
     }
 
-    g_led_control_registers_update_required = true;
+    g_led_control_registers_update_required[led.driver] = true;
 
 }
 
-void IS31FL3733_update_pwm_buffers( uint8_t addr1, uint8_t addr2 )
+void IS31FL3733_update_pwm_buffers( uint8_t addr, uint8_t index )
 {
-    if ( g_pwm_buffer_update_required )
+    if ( g_pwm_buffer_update_required[index] )
     {
         // Firstly we need to unlock the command register and select PG1
-        IS31FL3733_write_register( addr1, ISSI_COMMANDREGISTER_WRITELOCK, 0xC5 );
-        IS31FL3733_write_register( addr1, ISSI_COMMANDREGISTER, ISSI_PAGE_PWM );
+        IS31FL3733_write_register( addr, ISSI_COMMANDREGISTER_WRITELOCK, 0xC5 );
+        IS31FL3733_write_register( addr, ISSI_COMMANDREGISTER, ISSI_PAGE_PWM );
 
-        IS31FL3733_write_pwm_buffer( addr1, g_pwm_buffer[0] );
-        //IS31FL3733_write_pwm_buffer( addr2, g_pwm_buffer[1] );
+        IS31FL3733_write_pwm_buffer( addr, g_pwm_buffer[index] );
     }
-    g_pwm_buffer_update_required = false;
+    g_pwm_buffer_update_required[index] = false;
 }
 
-void IS31FL3733_update_led_control_registers( uint8_t addr1, uint8_t addr2 )
+void IS31FL3733_update_led_control_registers( uint8_t addr, uint8_t index )
 {
-    if ( g_led_control_registers_update_required )
+    if ( g_led_control_registers_update_required[index] )
     {
         // Firstly we need to unlock the command register and select PG0
-        IS31FL3733_write_register( addr1, ISSI_COMMANDREGISTER_WRITELOCK, 0xC5 );
-        IS31FL3733_write_register( addr1, ISSI_COMMANDREGISTER, ISSI_PAGE_LEDCONTROL );
+        IS31FL3733_write_register( addr, ISSI_COMMANDREGISTER_WRITELOCK, 0xC5 );
+        IS31FL3733_write_register( addr, ISSI_COMMANDREGISTER, ISSI_PAGE_LEDCONTROL );
         for ( int i=0; i<24; i++ )
         {
-            IS31FL3733_write_register(addr1, i, g_led_control_registers[0][i] );
-            //IS31FL3733_write_register(addr2, i, g_led_control_registers[1][i] );
+            IS31FL3733_write_register(addr, i, g_led_control_registers[index][i] );
         }
     }
+    g_led_control_registers_update_required[index] = false;
 }

drivers/issi/is31fl3733.h

@@ -32,7 +32,7 @@ typedef struct is31_led {
 
 extern const is31_led g_is31_leds[DRIVER_LED_TOTAL];
 
-void IS31FL3733_init( uint8_t addr );
+void IS31FL3733_init( uint8_t addr, uint8_t sync );
 void IS31FL3733_write_register( uint8_t addr, uint8_t reg, uint8_t data );
 void IS31FL3733_write_pwm_buffer( uint8_t addr, uint8_t *pwm_buffer );
 
@@ -45,8 +45,8 @@ void IS31FL3733_set_led_control_register( uint8_t index, bool red, bool green, b
 // (eg. from a timer interrupt).
 // Call this while idle (in between matrix scans).
 // If the buffer is dirty, it will update the driver with the buffer.
-void IS31FL3733_update_pwm_buffers( uint8_t addr1, uint8_t addr2 );
-void IS31FL3733_update_led_control_registers( uint8_t addr1, uint8_t addr2 );
+void IS31FL3733_update_pwm_buffers( uint8_t addr, uint8_t index );
+void IS31FL3733_update_led_control_registers( uint8_t addr, uint8_t index );
 
 #define A_1  0x00
 #define A_2  0x01

keyboards/40percentclub/nein/config.h

@@ -0,0 +1,239 @@
+/* Copyright 2019
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0xFEED
+#define PRODUCT_ID      0x0A0C
+#define DEVICE_VER      0x9999
+#define MANUFACTURER    di0ib
+#define PRODUCT         The nein Keyboard
+#define DESCRIPTION     9 key macropad
+
+/* key matrix size */
+#define MATRIX_ROWS 3
+#define MATRIX_COLS 3
+
+/* Keyboard Matrix Assignments */
+#define DIRECT_PINS { \
+    { F4, F5, F6 }, \
+    { F7, B1, B3 }, \
+    { B2, B6, B5 }  \
+}
+#define UNUSED_PINS
+
+/*
+ * Split Keyboard specific options, make sure you have 'SPLIT_KEYBOARD = yes' in your rules.mk, and define SOFT_SERIAL_PIN.
+ */
+// #define SOFT_SERIAL_PIN D0 // or D1, D2, D3, E6
+
+// #define BACKLIGHT_PIN B7
+// #define BACKLIGHT_BREATHING
+// #define BACKLIGHT_LEVELS 3
+
+// #define RGB_DI_PIN E2
+// #ifdef RGB_DI_PIN
+//   #define RGBLED_NUM 16
+//   #define RGBLIGHT_HUE_STEP 8
+//   #define RGBLIGHT_SAT_STEP 8
+//   #define RGBLIGHT_VAL_STEP 8
+//   #define RGBLIGHT_LIMIT_VAL 255 /* The maximum brightness level */
+//   #define RGBLIGHT_SLEEP  /* If defined, the RGB lighting will be switched off when the host goes to sleep */
+// /*== all animations enable ==*/
+//   #define RGBLIGHT_ANIMATIONS
+// /*== or choose animations ==*/
+//   #define RGBLIGHT_EFFECT_BREATHING
+//   #define RGBLIGHT_EFFECT_RAINBOW_MOOD
+//   #define RGBLIGHT_EFFECT_RAINBOW_SWIRL
+//   #define RGBLIGHT_EFFECT_SNAKE
+//   #define RGBLIGHT_EFFECT_KNIGHT
+//   #define RGBLIGHT_EFFECT_CHRISTMAS
+//   #define RGBLIGHT_EFFECT_STATIC_GRADIENT
+//   #define RGBLIGHT_EFFECT_RGB_TEST
+//   #define RGBLIGHT_EFFECT_ALTERNATING
+// /*== customize breathing effect ==*/
+//   /*==== (DEFAULT) use fixed table instead of exp() and sin() ====*/
+//   #define RGBLIGHT_BREATHE_TABLE_SIZE 256      // 256(default) or 128 or 64
+//   /*==== use exp() and sin() ====*/
+//   #define RGBLIGHT_EFFECT_BREATHE_CENTER 1.85  // 1 to 2.7
+//   #define RGBLIGHT_EFFECT_BREATHE_MAX    255   // 0 to 255
+// #endif
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCING_DELAY 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/* If defined, GRAVE_ESC will always act as ESC when CTRL is held.
+ * This is userful for the Windows task manager shortcut (ctrl+shift+esc).
+ */
+// #define GRAVE_ESC_CTRL_OVERRIDE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/* key combination for magic key command */
+/* defined by default; to change, uncomment and set to the combination you want */
+// #define IS_COMMAND() (get_mods() == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)))
+
+/* control how magic key switches layers */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
+
+/* override magic key keymap */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
+//#define MAGIC_KEY_HELP           H
+//#define MAGIC_KEY_HELP_ALT       SLASH
+//#define MAGIC_KEY_DEBUG          D
+//#define MAGIC_KEY_DEBUG_MATRIX   X
+//#define MAGIC_KEY_DEBUG_KBD      K
+//#define MAGIC_KEY_DEBUG_MOUSE    M
+//#define MAGIC_KEY_VERSION        V
+//#define MAGIC_KEY_STATUS         S
+//#define MAGIC_KEY_CONSOLE        C
+//#define MAGIC_KEY_LAYER0         0
+//#define MAGIC_KEY_LAYER0_ALT     GRAVE
+//#define MAGIC_KEY_LAYER1         1
+//#define MAGIC_KEY_LAYER2         2
+//#define MAGIC_KEY_LAYER3         3
+//#define MAGIC_KEY_LAYER4         4
+//#define MAGIC_KEY_LAYER5         5
+//#define MAGIC_KEY_LAYER6         6
+//#define MAGIC_KEY_LAYER7         7
+//#define MAGIC_KEY_LAYER8         8
+//#define MAGIC_KEY_LAYER9         9
+//#define MAGIC_KEY_BOOTLOADER     B
+//#define MAGIC_KEY_BOOTLOADER_ALT ESC
+//#define MAGIC_KEY_LOCK           CAPS
+//#define MAGIC_KEY_EEPROM         E
+//#define MAGIC_KEY_EEPROM_CLEAR   BSPACE
+//#define MAGIC_KEY_NKRO           N
+//#define MAGIC_KEY_SLEEP_LED      Z
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+/*
+ * MIDI options
+ */
+
+/* Prevent use of disabled MIDI features in the keymap */
+//#define MIDI_ENABLE_STRICT 1
+
+/* enable basic MIDI features:
+   - MIDI notes can be sent when in Music mode is on
+*/
+//#define MIDI_BASIC
+
+/* enable advanced MIDI features:
+   - MIDI notes can be added to the keymap
+   - Octave shift and transpose
+   - Virtual sustain, portamento, and modulation wheel
+   - etc.
+*/
+//#define MIDI_ADVANCED
+
+/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
+//#define MIDI_TONE_KEYCODE_OCTAVES 1
+
+/*
+ * HD44780 LCD Display Configuration
+ */
+/*
+#define LCD_LINES           2     //< number of visible lines of the display
+#define LCD_DISP_LENGTH    16     //< visibles characters per line of the display
+#define LCD_IO_MODE      1            //< 0: memory mapped mode, 1: IO port mode
+#if LCD_IO_MODE
+#define LCD_PORT         PORTB        //< port for the LCD lines
+#define LCD_DATA0_PORT   LCD_PORT     //< port for 4bit data bit 0
+#define LCD_DATA1_PORT   LCD_PORT     //< port for 4bit data bit 1
+#define LCD_DATA2_PORT   LCD_PORT     //< port for 4bit data bit 2
+#define LCD_DATA3_PORT   LCD_PORT     //< port for 4bit data bit 3
+#define LCD_DATA0_PIN    4            //< pin for 4bit data bit 0
+#define LCD_DATA1_PIN    5            //< pin for 4bit data bit 1
+#define LCD_DATA2_PIN    6            //< pin for 4bit data bit 2
+#define LCD_DATA3_PIN    7            //< pin for 4bit data bit 3
+#define LCD_RS_PORT      LCD_PORT     //< port for RS line
+#define LCD_RS_PIN       3            //< pin  for RS line
+#define LCD_RW_PORT      LCD_PORT     //< port for RW line
+#define LCD_RW_PIN       2            //< pin  for RW line
+#define LCD_E_PORT       LCD_PORT     //< port for Enable line
+#define LCD_E_PIN        1            //< pin  for Enable line
+#endif
+*/
+
+/* Bootmagic Lite key configuration */
+// #define BOOTMAGIC_LITE_ROW 0
+// #define BOOTMAGIC_LITE_COLUMN 0

keyboards/40percentclub/nein/info.json

@@ -0,0 +1,22 @@
+{
+  "keyboard_name": "nein",
+  "url": "",
+  "maintainer": "qmk",
+  "width": 3,
+  "height": 3,
+  "layouts": {
+    "LAYOUT": {
+      "layout": [
+        {"x":0, "y":0},
+        {"x":1, "y":0},
+        {"x":2, "y":0},
+        {"x":0, "y":1},
+        {"x":1, "y":1},
+        {"x":2, "y":1},
+        {"x":0, "y":2},
+        {"x":1, "y":2},
+        {"x":2, "y":2}
+      ]
+    }
+  }
+}

keyboards/40percentclub/nein/keymaps/default/keymap.c

@@ -0,0 +1,29 @@
+/* Copyright 2019
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include QMK_KEYBOARD_H
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+    [0] = LAYOUT_ortho_3x3(
+        KC_MUTE, KC_HOME, KC_MPLY, \
+        MO(1),   KC_UP,   KC_END, \
+        KC_LEFT, KC_DOWN, KC_RGHT \
+    ),
+    [1] = LAYOUT_ortho_3x3(
+        RESET,   _______, KC_STOP, \
+        _______, _______, RGB_MOD, \
+        KC_MPRV, _______, KC_MNXT \
+    ),
+};

keyboards/40percentclub/nein/nein.c

@@ -0,0 +1,16 @@
+/* Copyright 2019
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include "nein.h"

keyboards/40percentclub/nein/nein.h

@@ -0,0 +1,37 @@
+/* Copyright 2019
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#pragma once
+
+#include "quantum.h"
+
+/* This a shortcut to help you visually see your layout.
+ *
+ * The first section contains all of the arguments representing the physical
+ * layout of the board and position of the keys.
+ *
+ * The second converts the arguments into a two-dimensional array which
+ * represents the switch matrix.
+ */
+#define LAYOUT_ortho_3x3( \
+    k00, k01, k02, \
+    k10, k11, k12, \
+    k20, k21, k22  \
+) \
+{ \
+    { k00, k01, k02 }, \
+    { k10, k11, k12 }, \
+    { k20, k21, k22 }  \
+}

keyboards/40percentclub/nein/readme.md

@@ -0,0 +1,18 @@
+# nein
+
+![nein](https://2.bp.blogspot.com/-avYV4grcAPQ/XL9a67SxgKI/AAAAAAACVCE/GSGVYRThaEEDd14M3LG34gQTv5ZabRI0QCEwYBhgL/s640/a.jpg)
+===
+
+A 9 key macropad.
+
+Powered by a Pro Micro and can fit any of the various different sized variations of Pro Micro.
+
+Keyboard Maintainer: QMK Community  
+Hardware Supported: nein PCB  
+Hardware Availability: [nein project on 40% Keyboards](https://www.40percent.club/2019/04/nein.html)
+
+Make example for this keyboard (after setting up your build environment):
+
+    make 40percentclub/nein:default
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/40percentclub/nein/rules.mk

@@ -0,0 +1,80 @@
+# MCU name
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   atmega32a    bootloadHID
+BOOTLOADER = caterina
+
+
+# If you don't know the bootloader type, then you can specify the
+# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
+#   Teensy halfKay      512
+#   Teensy++ halfKay    1024
+#   Atmel DFU loader    4096
+#   LUFA bootloader     4096
+#   USBaspLoader        2048
+# OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE = lite     # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = no         # Console for debug(+400)
+COMMAND_ENABLE = no         # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE = yes           # USB Nkey Rollover
+BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality on B7 by default
+RGBLIGHT_ENABLE = no        # Enable keyboard RGB underglow
+MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no           # Audio output on port C6
+FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
+HD44780_ENABLE = no 	    # Enable support for HD44780 based LCDs (+400)

keyboards/ai03/lunar/info.json

@@ -7,7 +7,78 @@
     "height": 5, 
     "layouts": {
         "LAYOUT": {
-            "layout": [{"label":"Esc", "x":0, "y":0}, {"label":"!", "x":1, "y":0}, {"label":"@", "x":2, "y":0}, {"label":"#", "x":3, "y":0}, {"label":"$", "x":4, "y":0}, {"label":"%", "x":5, "y":0}, {"label":"^", "x":6, "y":0}, {"label":"&", "x":7, "y":0}, {"label":"*", "x":8, "y":0}, {"label":"(", "x":9, "y":0}, {"label":")", "x":10, "y":0}, {"label":"_", "x":11, "y":0}, {"label":"+", "x":12, "y":0}, {"label":"Backspace", "x":13, "y":0, "w":2}, {"label":"Insert", "x":15, "y":0}, {"label":"Tab", "x":0, "y":1, "w":1.5}, {"label":"Q", "x":1.5, "y":1}, {"label":"W", "x":2.5, "y":1}, {"label":"E", "x":3.5, "y":1}, {"label":"R", "x":4.5, "y":1}, {"label":"T", "x":5.5, "y":1}, {"label":"Y", "x":6.5, "y":1}, {"label":"U", "x":7.5, "y":1}, {"label":"I", "x":8.5, "y":1}, {"label":"O", "x":9.5, "y":1}, {"label":"P", "x":10.5, "y":1}, {"label":"{", "x":11.5, "y":1}, {"label":"}", "x":12.5, "y":1}, {"label":"|", "x":13.5, "y":1, "w":1.5}, {"label":"Delete", "x":15, "y":1}, {"label":"Caps Lock", "x":0, "y":2, "w":1.75}, {"label":"A", "x":1.75, "y":2}, {"label":"S", "x":2.75, "y":2}, {"label":"D", "x":3.75, "y":2}, {"label":"F", "x":4.75, "y":2}, {"label":"G", "x":5.75, "y":2}, {"label":"H", "x":6.75, "y":2}, {"label":"J", "x":7.75, "y":2}, {"label":"K", "x":8.75, "y":2}, {"label":"L", "x":9.75, "y":2}, {"label":":", "x":10.75, "y":2}, {"label":"\"", "x":11.75, "y":2}, {"label":"Enter", "x":12.75, "y":2, "w":2.25}, {"label":"Home", "x":15, "y":2}, {"label":"Shift", "x":0, "y":3, "w":2.25}, {"label":"Z", "x":2.25, "y":3}, {"label":"X", "x":3.25, "y":3}, {"label":"C", "x":4.25, "y":3}, {"label":"V", "x":5.25, "y":3}, {"label":"B", "x":6.25, "y":3}, {"label":"N", "x":7.25, "y":3}, {"label":"M", "x":8.25, "y":3}, {"label":"<", "x":9.25, "y":3}, {"label":">", "x":10.25, "y":3}, {"label":"?", "x":11.25, "y":3}, {"label":"Shift", "x":12.25, "y":3, "w":1.75}, {"label":"\u2191", "x":14, "y":3}, {"label":"End", "x":15, "y":3}, {"label":"Ctrl", "x":0, "y":4, "w":1.5}, {"label":"Win", "x":1.5, "y":4, "w":1.25}, {"label":"Alt", "x":2.75, "y":4, "w":1.5}, {"x":4.25, "y":4, "w":2.25}, {"x":6.5, "y":4, "w":1.5}, {"x":8, "y":4, "w":2.75}, {"label":"Alt", "x":10.75, "y":4, "w":1.25}, {"label":"Win", "x":12, "y":4}, {"label":"\u2190", "x":13, "y":4}, {"label":"\u2193", "x":14, "y":4}, {"label":"\u2192", "x":15, "y":4}]
+            "layout": [
+                {"label":"Esc", "x":0, "y":0},
+                {"label":"!", "x":1, "y":0},
+                {"label":"@", "x":2, "y":0},
+                {"label":"#", "x":3, "y":0},
+                {"label":"$", "x":4, "y":0},
+                {"label":"%", "x":5, "y":0},
+                {"label":"^", "x":6, "y":0},
+                {"label":"&", "x":7, "y":0},
+                {"label":"*", "x":8, "y":0},
+                {"label":"(", "x":9, "y":0},
+                {"label":")", "x":10, "y":0},
+                {"label":"_", "x":11, "y":0},
+                {"label":"+", "x":12, "y":0},
+                {"label":"BackspaceL", "x":13, "y":0},
+                {"label":"BackspaceR", "x":14, "y":0},
+                {"label":"Insert", "x":15, "y":0},
+                {"label":"Tab", "x":0, "y":1, "w":1.5},
+                {"label":"Q", "x":1.5, "y":1},
+                {"label":"W", "x":2.5, "y":1},
+                {"label":"E", "x":3.5, "y":1},
+                {"label":"R", "x":4.5, "y":1},
+                {"label":"T", "x":5.5, "y":1},
+                {"label":"Y", "x":6.5, "y":1},
+                {"label":"U", "x":7.5, "y":1},
+                {"label":"I", "x":8.5, "y":1},
+                {"label":"O", "x":9.5, "y":1},
+                {"label":"P", "x":10.5, "y":1},
+                {"label":"{", "x":11.5, "y":1},
+                {"label":"}", "x":12.5, "y":1},
+                {"label":"|", "x":13.5, "y":1, "w":1.5},
+                {"label":"Delete", "x":15, "y":1},
+                {"label":"Caps Lock", "x":0, "y":2, "w":1.75},
+                {"label":"A", "x":1.75, "y":2},
+                {"label":"S", "x":2.75, "y":2},
+                {"label":"D", "x":3.75, "y":2},
+                {"label":"F", "x":4.75, "y":2},
+                {"label":"G", "x":5.75, "y":2},
+                {"label":"H", "x":6.75, "y":2},
+                {"label":"J", "x":7.75, "y":2},
+                {"label":"K", "x":8.75, "y":2},
+                {"label":"L", "x":9.75, "y":2},
+                {"label":":", "x":10.75, "y":2},
+                {"label":"\"", "x":11.75, "y":2},
+                {"label":"Enter", "x":12.75, "y":2, "w":2.25},
+                {"label":"Home", "x":15, "y":2},
+                {"label":"Shift", "x":0, "y":3, "w":2.25},
+                {"label":"Z", "x":2.25, "y":3},
+                {"label":"X", "x":3.25, "y":3},
+                {"label":"C", "x":4.25, "y":3},
+                {"label":"V", "x":5.25, "y":3},
+                {"label":"B", "x":6.25, "y":3},
+                {"label":"N", "x":7.25, "y":3},
+                {"label":"M", "x":8.25, "y":3},
+                {"label":"<", "x":9.25, "y":3},
+                {"label":">", "x":10.25, "y":3},
+                {"label":"?", "x":11.25, "y":3},
+                {"label":"Shift", "x":12.25, "y":3, "w":1.75},
+                {"label":"\u2191", "x":14, "y":3},
+                {"label":"End", "x":15, "y":3},
+                {"label":"Ctrl", "x":0, "y":4, "w":1.5},
+                {"label":"Win", "x":1.5, "y":4, "w":1.25},
+                {"label":"Alt", "x":2.75, "y":4, "w":1.5},
+                {"x":4.25, "y":4, "w":2.25},
+                {"x":6.5, "y":4, "w":1.5},
+                {"x":8, "y":4, "w":2.75},
+                {"label":"Alt", "x":10.75, "y":4, "w":1.25},
+                {"label":"Win", "x":12, "y":4},
+                {"label":"\u2190", "x":13, "y":4},
+                {"label":"\u2193", "x":14, "y":4},
+                {"label":"\u2192", "x":15, "y":4}
+            ]
         }
     }
 }

keyboards/ai03/orbit/info.json

@@ -0,0 +1,88 @@
+{
+    "keyboard_name": "orbit", 
+    "url": "https://github.com/ai03-2725/Orbit", 
+    "maintainer": "ai03", 
+    "width": 16, 
+    "height": 6, 
+    "layouts": {
+        "LAYOUT": {
+            "layout": [
+                {"x":0,  "y":0.63},
+                {"x":1,  "y":0.38},
+                {"x":2,  "y":0.38},
+                {"x":3,  "y":0.13},
+                {"x":4,  "y":0},
+                {"x":5,  "y":0.13},
+                {"x":6,  "y":0.25},
+                {"x":9,  "y":0.25},
+                {"x":10, "y":0.13},
+                {"x":11, "y":0},
+                {"x":12, "y":0.13},
+                {"x":13, "y":0.38},
+                {"x":14, "y":0.38},
+                {"x":15, "y":0.63},
+
+                {"x":0,  "y":1.63},
+                {"x":1,  "y":1.38},
+                {"x":2,  "y":1.38},
+                {"x":3,  "y":1.13},
+                {"x":4,  "y":1},
+                {"x":5,  "y":1.13},
+                {"x":6,  "y":1.25},
+                {"x":9,  "y":1.25},
+                {"x":10, "y":1.13},
+                {"x":11, "y":1},
+                {"x":12, "y":1.13},
+                {"x":13, "y":1.38},
+                {"x":14, "y":1.38},
+                {"x":15, "y":1.63},
+
+                {"x":0,  "y":2.63},
+                {"x":1,  "y":2.38},
+                {"x":2,  "y":2.38},
+                {"x":3,  "y":2.13},
+                {"x":4,  "y":2},
+                {"x":5,  "y":2.13},
+                {"x":6,  "y":2.25},
+                {"x":9,  "y":2.25},
+                {"x":10, "y":2.13},
+                {"x":11, "y":2},
+                {"x":12, "y":2.13},
+                {"x":13, "y":2.38},
+                {"x":14, "y":2.38},
+                {"x":15, "y":2.63},
+
+                {"x":0,  "y":3.63},
+                {"x":1,  "y":3.38},
+                {"x":2,  "y":3.38},
+                {"x":3,  "y":3.13},
+                {"x":4,  "y":3},
+                {"x":5,  "y":3.13},
+                {"x":6,  "y":3.25},
+                {"x":9,  "y":3.25},
+                {"x":10, "y":3.13},
+                {"x":11, "y":3},
+                {"x":12, "y":3.13},
+                {"x":13, "y":3.38},
+                {"x":14, "y":3.38},
+                {"x":15, "y":3.63},
+
+                {"x":1,  "y":4.38},
+                {"x":2,  "y":4.38},
+                {"x":3,  "y":4.13},
+                {"x":4,  "y":4},
+
+                {"x":5.5, "y":4.25},
+                {"x":6.5, "y":4.5, "h":1.5},
+
+                {"x":8.5, "y":4.5, "h":1.5},
+                {"x":9.5, "y":4.25},
+
+                {"x":11, "y":4},
+                {"x":12, "y":4.13},
+                {"x":13, "y":4.38},
+                {"x":14, "y":4.38}
+            ]
+        }
+    }
+}

keyboards/butterstick/keymaps/default/keymap.c

@@ -45,6 +45,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
 uint32_t processQwerty(bool lookup) {
     // SECRET AGENT CHORDS
     P( LSU | LK | RS | RD,    	SEND_STRING(VERSION); SEND_STRING(__DATE__));
+	P( LR  | ST2| RR | RB, 		SEND(KC_BSPC));
     P( LSD | RZ,   			 	SEND(KC_SPC));
 
     // Dual chords

keyboards/claw44/ssd1306.c

@@ -13,7 +13,7 @@
 #include "sendchar.h"
 #include "timer.h"
 
-static const unsigned char font[] PROGMEM;
+extern const unsigned char font[] PROGMEM;
 
 // Set this to 1 to help diagnose early startup problems
 // when testing power-on with ble.  Turn it off otherwise,

keyboards/comet46/ssd1306.c

@@ -13,7 +13,7 @@
 #include "sendchar.h"
 #include "timer.h"
 
-static const unsigned char font[] PROGMEM;
+extern const unsigned char font[] PROGMEM;
 
 // Set this to 1 to help diagnose early startup problems
 // when testing power-on with ble.  Turn it off otherwise,

keyboards/converter/modelm101/keymaps/default/keymap.c

@@ -21,7 +21,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
     KC_GRV,  KC_1,    KC_2,   KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    KC_MINS, KC_EQL,  KC_BSPC,   KC_INS,  KC_HOME, KC_PGUP,   KC_NLCK, KC_PSLS, KC_PAST, KC_PMNS,
     KC_TAB,  KC_Q,    KC_W,   KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_LBRC, KC_RBRC, KC_BSLS,   KC_DEL,  KC_END,  KC_PGDN,   KC_P7,   KC_P8,   KC_P9,   KC_PPLS,
     KC_CAPS, KC_A,    KC_S,   KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN, KC_QUOT, KC_NUHS, KC_ENT,                                 KC_P4,   KC_P5,   KC_P6,
-    KC_LSFT, KC_NUBS, KC_Z,   KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH,          KC_RSFT,            KC_UP,              KC_P1,   KC_P2,   KC_P3,   KC_LGUI,
+    KC_LSFT, KC_NUBS, KC_Z,   KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH,          KC_RSFT,            KC_UP,              KC_P1,   KC_P2,   KC_P3,   KC_PENT,
     KC_LCTL,          KC_LALT,                           KC_SPC,                                      KC_RALT,          KC_RCTL,   KC_LEFT, KC_DOWN, KC_RGHT,   KC_P0,            KC_PDOT
   ),
 };

keyboards/crkbd/ssd1306.c

@@ -13,7 +13,7 @@
 #include "sendchar.h"
 #include "timer.h"
 
-static const unsigned char font[] PROGMEM;
+extern const unsigned char font[] PROGMEM;
 
 // Set this to 1 to help diagnose early startup problems
 // when testing power-on with ble.  Turn it off otherwise,

keyboards/doro67/multi/multi.c

@@ -19,6 +19,7 @@ void matrix_init_kb(void) {
 	// put your keyboard start-up code here
 	// runs once when the firmware starts up
 
+    setPinOutput(E6);
 	matrix_init_user();
 }
 
@@ -39,5 +40,11 @@ bool process_record_kb(uint16_t keycode, keyrecord_t *record) {
 void led_set_kb(uint8_t usb_led) {
 	// put your keyboard LED indicator (ex: Caps Lock LED) toggling code here
 
+	if (IS_LED_ON(usb_led, USB_LED_CAPS_LOCK)) {
+		writePinLow(E6);
+	} else {
+		writePinHigh(E6);
+	}
+
 	led_set_user(usb_led);
 }

keyboards/ergodox_ez/info.json

@@ -1,7 +1,7 @@
 {
     "keyboard_name": "ErgoDox EZ",
     "url": "ergodox-ez.com",
-    "maintainer": "erez",
+    "maintainer": "ZSA",
     "width": 17,
     "height": 8,
 

keyboards/ergodox_ez/matrix.c

@@ -1,9 +1,5 @@
 /*
 
-Note for ErgoDox EZ customizers: Here be dragons!
-This is not a file you want to be messing with.
-All of the interesting stuff for you is under keymaps/ :)
-Love, Erez
 
 Copyright 2013 Oleg Kostyuk <cub.uanic@gmail.com>
 
@@ -95,7 +91,7 @@ void matrix_init(void) {
   // initialize matrix state: all keys off
   for (uint8_t i = 0; i < MATRIX_ROWS; i++) {
     matrix[i]     = 0;
-    raw_matrix[i] = 0;    
+    raw_matrix[i] = 0;
   }
 
 #ifdef DEBUG_MATRIX_SCAN_RATE
@@ -168,7 +164,7 @@ uint8_t matrix_scan(void) {
 #ifdef LEFT_LEDS
   mcp23018_status = ergodox_left_leds_update();
 #endif  // LEFT_LEDS
-  bool changed = false;  
+  bool changed = false;
   for (uint8_t i = 0; i < MATRIX_ROWS_PER_SIDE; i++) {
     // select rows from left and right hands
     uint8_t left_index = i;
@@ -178,13 +174,13 @@ uint8_t matrix_scan(void) {
 
     // we don't need a 30us delay anymore, because selecting a
     // left-hand row requires more than 30us for i2c.
-    
+
     changed |= store_raw_matrix_row(left_index);
     changed |= store_raw_matrix_row(right_index);
 
     unselect_rows();
   }
-  
+
   debounce(raw_matrix, matrix, MATRIX_ROWS, changed);
   matrix_scan_quantum();
 

keyboards/ergotaco/matrix.c

@@ -1,8 +1,4 @@
 /*
-Note for ErgoDox EZ customizers: Here be dragons!
-This is not a file you want to be messing with.
-All of the interesting stuff for you is under keymaps/ :)
-Love, Erez
 
 Copyright 2013 Oleg Kostyuk <cub.uanic@gmail.com>
 
@@ -226,8 +222,8 @@ uint8_t matrix_scan(void)
     matrix_scan_quantum();
 
 #ifdef DEBUG_MATRIX
-    for (uint8_t c = 0; c < MATRIX_COLS; c++) 
-		for (uint8_t r = 0; r < MATRIX_ROWS; r++) 
+    for (uint8_t c = 0; c < MATRIX_COLS; c++)
+		for (uint8_t r = 0; r < MATRIX_ROWS; r++)
 		  if (matrix_is_on(r, c)) xprintf("r:%d c:%d \n", r, c);
 #endif
 
@@ -324,10 +320,10 @@ static void unselect_rows(void)
 static void select_row(uint8_t row)
 {
     if (row < 6) {
-        // select on mcp23018 
+        // select on mcp23018
         if (mcp23018_status) { // do nothing on error
 			// Read using bitmask
-        } else { // set active row low  : 0 // set other rows hi-Z : 1 
+        } else { // set active row low  : 0 // set other rows hi-Z : 1
             mcp23018_status = i2c_start(I2C_ADDR_WRITE, ERGODOX_EZ_I2C_TIMEOUT);        if (mcp23018_status) goto out;
             mcp23018_status = i2c_write(GPIOA, ERGODOX_EZ_I2C_TIMEOUT);                 if (mcp23018_status) goto out;
             mcp23018_status = i2c_write(~(1<<row), ERGODOX_EZ_I2C_TIMEOUT);      		if (mcp23018_status) goto out;

keyboards/foxlab/leaf60/hotswap/config.h

@@ -0,0 +1,229 @@
+/*
+Copyright 2019 Fox Lab
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0xFEED
+#define PRODUCT_ID      0x0000
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    Fox Lab
+#define PRODUCT         Leaf60 Hotswap
+#define DESCRIPTION     A custom hotswap 60% keyboard
+
+/* key matrix size */
+#define MATRIX_ROWS 5
+#define MATRIX_COLS 15
+
+/*
+ * Keyboard Matrix Assignments
+ *
+ * Change this to how you wired your keyboard
+ * COLS: AVR pins used for columns, left to right
+ * ROWS: AVR pins used for rows, top to bottom
+ * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
+ *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
+ *
+*/
+#define MATRIX_ROW_PINS { D2, D1, D0, D3, D5 }
+#define MATRIX_COL_PINS { F5, F4, F1, F0, B0, F6, F7, C7, C6, B6, B5, B4, D7, D6, D4 }
+#define UNUSED_PINS
+
+/* COL2ROW, ROW2COL*/
+#define DIODE_DIRECTION COL2ROW
+
+#define BACKLIGHT_PIN B7
+#define BACKLIGHT_BREATHING
+#define BACKLIGHT_LEVELS 4
+
+#define RGB_DI_PIN E2
+#ifdef RGB_DI_PIN
+  #define RGBLED_NUM 8
+  #define RGBLIGHT_HUE_STEP 8
+  #define RGBLIGHT_SAT_STEP 8
+  #define RGBLIGHT_VAL_STEP 8
+  #define RGBLIGHT_SLEEP  /* If defined, the RGB lighting will be switched off when the host goes to sleep */
+/*== all animations enable ==*/
+  #define RGBLIGHT_ANIMATIONS
+#endif
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCING_DELAY 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/* If defined, GRAVE_ESC will always act as ESC when CTRL is held.
+ * This is userful for the Windows task manager shortcut (ctrl+shift+esc).
+ */
+// #define GRAVE_ESC_CTRL_OVERRIDE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/* key combination for magic key command */
+/* defined by default; to change, uncomment and set to the combination you want */
+// #define IS_COMMAND() (get_mods() == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)))
+
+/* control how magic key switches layers */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
+
+/* override magic key keymap */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
+//#define MAGIC_KEY_HELP           H
+//#define MAGIC_KEY_HELP_ALT       SLASH
+//#define MAGIC_KEY_DEBUG          D
+//#define MAGIC_KEY_DEBUG_MATRIX   X
+//#define MAGIC_KEY_DEBUG_KBD      K
+//#define MAGIC_KEY_DEBUG_MOUSE    M
+//#define MAGIC_KEY_VERSION        V
+//#define MAGIC_KEY_STATUS         S
+//#define MAGIC_KEY_CONSOLE        C
+//#define MAGIC_KEY_LAYER0         0
+//#define MAGIC_KEY_LAYER0_ALT     GRAVE
+//#define MAGIC_KEY_LAYER1         1
+//#define MAGIC_KEY_LAYER2         2
+//#define MAGIC_KEY_LAYER3         3
+//#define MAGIC_KEY_LAYER4         4
+//#define MAGIC_KEY_LAYER5         5
+//#define MAGIC_KEY_LAYER6         6
+//#define MAGIC_KEY_LAYER7         7
+//#define MAGIC_KEY_LAYER8         8
+//#define MAGIC_KEY_LAYER9         9
+//#define MAGIC_KEY_BOOTLOADER     B
+//#define MAGIC_KEY_BOOTLOADER_ALT ESC
+//#define MAGIC_KEY_LOCK           CAPS
+//#define MAGIC_KEY_EEPROM         E
+//#define MAGIC_KEY_EEPROM_CLEAR   BSPACE
+//#define MAGIC_KEY_NKRO           N
+//#define MAGIC_KEY_SLEEP_LED      Z
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+/*
+ * MIDI options
+ */
+
+/* Prevent use of disabled MIDI features in the keymap */
+//#define MIDI_ENABLE_STRICT 1
+
+/* enable basic MIDI features:
+   - MIDI notes can be sent when in Music mode is on
+*/
+//#define MIDI_BASIC
+
+/* enable advanced MIDI features:
+   - MIDI notes can be added to the keymap
+   - Octave shift and transpose
+   - Virtual sustain, portamento, and modulation wheel
+   - etc.
+*/
+//#define MIDI_ADVANCED
+
+/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
+//#define MIDI_TONE_KEYCODE_OCTAVES 1
+
+/*
+ * HD44780 LCD Display Configuration
+ */
+/*
+#define LCD_LINES           2     //< number of visible lines of the display
+#define LCD_DISP_LENGTH    16     //< visibles characters per line of the display
+
+#define LCD_IO_MODE      1            //< 0: memory mapped mode, 1: IO port mode
+
+#if LCD_IO_MODE
+#define LCD_PORT         PORTB        //< port for the LCD lines
+#define LCD_DATA0_PORT   LCD_PORT     //< port for 4bit data bit 0
+#define LCD_DATA1_PORT   LCD_PORT     //< port for 4bit data bit 1
+#define LCD_DATA2_PORT   LCD_PORT     //< port for 4bit data bit 2
+#define LCD_DATA3_PORT   LCD_PORT     //< port for 4bit data bit 3
+#define LCD_DATA0_PIN    4            //< pin for 4bit data bit 0
+#define LCD_DATA1_PIN    5            //< pin for 4bit data bit 1
+#define LCD_DATA2_PIN    6            //< pin for 4bit data bit 2
+#define LCD_DATA3_PIN    7            //< pin for 4bit data bit 3
+#define LCD_RS_PORT      LCD_PORT     //< port for RS line
+#define LCD_RS_PIN       3            //< pin  for RS line
+#define LCD_RW_PORT      LCD_PORT     //< port for RW line
+#define LCD_RW_PIN       2            //< pin  for RW line
+#define LCD_E_PORT       LCD_PORT     //< port for Enable line
+#define LCD_E_PIN        1            //< pin  for Enable line
+#endif
+*/
+
+/* Bootmagic Lite key configuration */
+// #define BOOTMAGIC_LITE_ROW 0
+// #define BOOTMAGIC_LITE_COLUMN 0

keyboards/foxlab/leaf60/hotswap/hotswap.c

@@ -0,0 +1,59 @@
+/* Copyright 2019 Fox Lab
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include "hotswap.h"
+
+// Optional override functions below.
+// You can leave any or all of these undefined.
+// These are only required if you want to perform custom actions.
+
+void matrix_init_kb(void) {
+  // put your keyboard start-up code here
+  // runs once when the firmware starts up
+  setPinOutput(E6);
+  matrix_init_user();
+}
+/*
+
+void matrix_scan_kb(void) {
+  // put your looping keyboard code here
+  // runs every cycle (a lot)
+
+  matrix_scan_user();
+}
+
+bool process_record_kb(uint16_t keycode, keyrecord_t *record) {
+  // put your per-action keyboard code here
+  // runs for every action, just before processing by the firmware
+
+  return process_record_user(keycode, record);
+}
+
+void led_set_kb(uint8_t usb_led) {
+  // put your keyboard LED indicator (ex: Caps Lock LED) toggling code here
+
+  led_set_user(usb_led);
+}
+
+*/
+
+void led_set_kb(uint8_t usb_led) {
+  if (IS_LED_ON(usb_led, USB_LED_CAPS_LOCK)) {
+    writePinLow(E6);
+  } else {
+    writePinHigh(E6);
+  }
+	led_set_user(usb_led);
+}

keyboards/foxlab/leaf60/hotswap/hotswap.h

@@ -0,0 +1,40 @@
+/* Copyright 2019 Fox Lab
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#pragma once
+
+#include "quantum.h"
+
+/* This a shortcut to help you visually see your layout.
+ *
+ * The first section contains all of the arguments representing the physical
+ * layout of the board and position of the keys.
+ *
+ * The second converts the arguments into a two-dimensional array which
+ * represents the switch matrix.
+ */
+#define LAYOUT_60_tsangan_hhkb( \
+	K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014, \
+	K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113,       \
+	K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212,             \
+	K300,       K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312, K313,       \
+	K400, K401, K402,                         K407,                   K411, K412, K413  \
+) { \
+	{ K000,  K001,  K002,  K003,  K004,  K005,  K006,  K007,  K008,  K009,  K010,  K011,  K012,  K013,  K014 }, \
+	{ K100,  K101,  K102,  K103,  K104,  K105,  K106,  K107,  K108,  K109,  K110,  K111,  K112,  K113,  KC_NO }, \
+	{ K200,  K201,  K202,  K203,  K204,  K205,  K206,  K207,  K208,  K209,  K210,  K211,  K212,  KC_NO, KC_NO }, \
+	{ K300,  KC_NO, K302,  K303,  K304,  K305,  K306,  K307,  K308,  K309,  K310,  K311,  K312,  K313,  KC_NO }, \
+	{ K400,  K401,  K402,  KC_NO, KC_NO, KC_NO, KC_NO, K407,  KC_NO, KC_NO, KC_NO, K411,  K412,  K413,  KC_NO }  \
+}

keyboards/foxlab/leaf60/hotswap/info.json

@@ -0,0 +1,12 @@
+{
+    "keyboard_name": "Fox Lab Hotswap Leaf60", 
+    "url": "", 
+    "maintainer": "qmk", 
+    "width": 15, 
+    "height": 5, 
+    "layouts": {
+        "LAYOUT_60_tsangan_hhkb": {
+            "layout": [{"x":0, "y":0}, {"x":1, "y":0}, {"x":2, "y":0}, {"x":3, "y":0}, {"x":4, "y":0}, {"x":5, "y":0}, {"x":6, "y":0}, {"x":7, "y":0}, {"x":8, "y":0}, {"x":9, "y":0}, {"x":10, "y":0}, {"x":11, "y":0}, {"x":12, "y":0}, {"x":13, "y":0}, {"x":14, "y":0}, {"x":0, "y":1, "w":1.5}, {"x":1.5, "y":1}, {"x":2.5, "y":1}, {"x":3.5, "y":1}, {"x":4.5, "y":1}, {"x":5.5, "y":1}, {"x":6.5, "y":1}, {"x":7.5, "y":1}, {"x":8.5, "y":1}, {"x":9.5, "y":1}, {"x":10.5, "y":1}, {"x":11.5, "y":1}, {"x":12.5, "y":1}, {"x":13.5, "y":1, "w":1.5}, {"x":0, "y":2, "w":1.75}, {"x":1.75, "y":2}, {"x":2.75, "y":2}, {"x":3.75, "y":2}, {"x":4.75, "y":2}, {"x":5.75, "y":2}, {"x":6.75, "y":2}, {"x":7.75, "y":2}, {"x":8.75, "y":2}, {"x":9.75, "y":2}, {"x":10.75, "y":2}, {"x":11.75, "y":2}, {"x":12.75, "y":2, "w":2.25}, {"x":0, "y":3, "w":2.25}, {"x":2.25, "y":3}, {"x":3.25, "y":3}, {"x":4.25, "y":3}, {"x":5.25, "y":3}, {"x":6.25, "y":3}, {"x":7.25, "y":3}, {"x":8.25, "y":3}, {"x":9.25, "y":3}, {"x":10.25, "y":3}, {"x":11.25, "y":3}, {"x":12.25, "y":3, "w":1.75}, {"x":14, "y":3}, {"x":0, "y":4, "w":1.5}, {"x":1.5, "y":4}, {"x":2.5, "y":4, "w":1.5}, {"x":4, "y":4, "w":7}, {"x":11, "y":4, "w":1.5}, {"x":12.5, "y":4}, {"x":13.5, "y":4, "w":1.5}]
+        }
+    }
+}

keyboards/foxlab/leaf60/hotswap/keymaps/default/config.h

@@ -0,0 +1,19 @@
+/* Copyright 2019 MechMerlin
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+
+// place overrides here

keyboards/foxlab/leaf60/hotswap/keymaps/default/keymap.c

@@ -0,0 +1,46 @@
+/* Copyright 2019 Fox Lab
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include QMK_KEYBOARD_H
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+	LAYOUT_60_tsangan_hhkb(
+		KC_ESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL,  KC_GRV, KC_BSLS,
+		KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSPC, 
+		KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_ENT, 
+		KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT, KC_DEL, 
+		KC_LCTL, KC_LGUI, KC_LALT, KC_SPC, MO(1), KC_RALT, KC_RCTL),
+
+	LAYOUT_60_tsangan_hhkb(
+		RESET, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_TRNS, KC_TRNS, 
+		KC_TRNS, BL_TOGG, BL_DEC, BL_INC, BL_STEP, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, 
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, 
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, 
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS)
+
+};
+
+void matrix_init_user(void) {
+
+}
+
+void matrix_scan_user(void) {
+
+}
+
+void led_set_user(uint8_t usb_led) {
+
+}

keyboards/foxlab/leaf60/hotswap/keymaps/default/readme.md

@@ -0,0 +1 @@
+# The default keymap for Fox Lab Hotswap Leaf60

keyboards/foxlab/leaf60/hotswap/readme.md

@@ -0,0 +1,13 @@
+# Fox Lab Hotswap Leaf60 
+
+A hotswap, Tsangan-layout, gasket-mount 60% keyboard.
+
+Keyboard Maintainer: [Fox Lab](https://github.com/fox-lab), [MechMerlin](https://github.com/mechmerlin)  
+Hardware Supported: Leaf60 powered by the ATmega32U4  
+Hardware Availability: [Geekhack Group Buy](https://geekhack.org/index.php?topic=99002.0)  
+
+Make example for this keyboard (after setting up your build environment):
+
+    make foxlab/leaf60/hotswap:default
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/foxlab/leaf60/hotswap/rules.mk

@@ -0,0 +1,80 @@
+# MCU name
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   atmega32a    bootloadHID
+BOOTLOADER = atmel-dfu
+
+
+# If you don't know the bootloader type, then you can specify the
+# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
+#   Teensy halfKay      512
+#   Teensy++ halfKay    1024
+#   Atmel DFU loader    4096
+#   LUFA bootloader     4096
+#   USBaspLoader        2048
+# OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE = yes      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = no        # Console for debug(+400)
+COMMAND_ENABLE = no        # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE = no            # USB Nkey Rollover
+BACKLIGHT_ENABLE = yes       # Enable keyboard backlight functionality on B7 by default
+RGBLIGHT_ENABLE = yes        # Enable keyboard RGB underglow
+MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no           # Audio output on port C6
+FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
+HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)

keyboards/foxlab/leaf60/readme.md

@@ -0,0 +1,7 @@
+# Fox Lab Leaf60
+
+The Leaf60 is a 60% gasket mount board sold via [Geekhack Group Buy](https://geekhack.org/index.php?topic=99002.0).
+
+It was available with a universal layout PCB and a hotswap tsangan PCB. 
+
+**Firmware generated for one PCB will not work on the other.**

keyboards/foxlab/leaf60/universal/config.h

@@ -0,0 +1,229 @@
+/*
+Copyright 2019 Fox Lab
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0xFEED
+#define PRODUCT_ID      0x0000
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    Fox Lab
+#define PRODUCT         Leaf60 Universal
+#define DESCRIPTION     A custom 60% keyboard
+
+/* key matrix size */
+#define MATRIX_ROWS 5
+#define MATRIX_COLS 15
+
+/*
+ * Keyboard Matrix Assignments
+ *
+ * Change this to how you wired your keyboard
+ * COLS: AVR pins used for columns, left to right
+ * ROWS: AVR pins used for rows, top to bottom
+ * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
+ *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
+ *
+*/
+#define MATRIX_ROW_PINS { D0, D1, F0, F4, F1 }
+#define MATRIX_COL_PINS { B0, F5, F6, F7, C7, C6, B6, B5, B4, D7, D6, D4, D5, D3, D2 }
+#define UNUSED_PINS
+
+/* COL2ROW, ROW2COL*/
+#define DIODE_DIRECTION COL2ROW
+
+#define BACKLIGHT_PIN B7
+#define BACKLIGHT_BREATHING
+#define BACKLIGHT_LEVELS 3
+
+#define RGB_DI_PIN E2
+#ifdef RGB_DI_PIN
+  #define RGBLED_NUM 8
+  #define RGBLIGHT_HUE_STEP 8
+  #define RGBLIGHT_SAT_STEP 8
+  #define RGBLIGHT_VAL_STEP 8
+  #define RGBLIGHT_SLEEP  /* If defined, the RGB lighting will be switched off when the host goes to sleep */
+/*== all animations enable ==*/
+  #define RGBLIGHT_ANIMATIONS
+#endif
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCING_DELAY 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/* If defined, GRAVE_ESC will always act as ESC when CTRL is held.
+ * This is userful for the Windows task manager shortcut (ctrl+shift+esc).
+ */
+// #define GRAVE_ESC_CTRL_OVERRIDE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/* key combination for magic key command */
+/* defined by default; to change, uncomment and set to the combination you want */
+// #define IS_COMMAND() (get_mods() == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)))
+
+/* control how magic key switches layers */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
+
+/* override magic key keymap */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
+//#define MAGIC_KEY_HELP           H
+//#define MAGIC_KEY_HELP_ALT       SLASH
+//#define MAGIC_KEY_DEBUG          D
+//#define MAGIC_KEY_DEBUG_MATRIX   X
+//#define MAGIC_KEY_DEBUG_KBD      K
+//#define MAGIC_KEY_DEBUG_MOUSE    M
+//#define MAGIC_KEY_VERSION        V
+//#define MAGIC_KEY_STATUS         S
+//#define MAGIC_KEY_CONSOLE        C
+//#define MAGIC_KEY_LAYER0         0
+//#define MAGIC_KEY_LAYER0_ALT     GRAVE
+//#define MAGIC_KEY_LAYER1         1
+//#define MAGIC_KEY_LAYER2         2
+//#define MAGIC_KEY_LAYER3         3
+//#define MAGIC_KEY_LAYER4         4
+//#define MAGIC_KEY_LAYER5         5
+//#define MAGIC_KEY_LAYER6         6
+//#define MAGIC_KEY_LAYER7         7
+//#define MAGIC_KEY_LAYER8         8
+//#define MAGIC_KEY_LAYER9         9
+//#define MAGIC_KEY_BOOTLOADER     B
+//#define MAGIC_KEY_BOOTLOADER_ALT ESC
+//#define MAGIC_KEY_LOCK           CAPS
+//#define MAGIC_KEY_EEPROM         E
+//#define MAGIC_KEY_EEPROM_CLEAR   BSPACE
+//#define MAGIC_KEY_NKRO           N
+//#define MAGIC_KEY_SLEEP_LED      Z
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+/*
+ * MIDI options
+ */
+
+/* Prevent use of disabled MIDI features in the keymap */
+//#define MIDI_ENABLE_STRICT 1
+
+/* enable basic MIDI features:
+   - MIDI notes can be sent when in Music mode is on
+*/
+//#define MIDI_BASIC
+
+/* enable advanced MIDI features:
+   - MIDI notes can be added to the keymap
+   - Octave shift and transpose
+   - Virtual sustain, portamento, and modulation wheel
+   - etc.
+*/
+//#define MIDI_ADVANCED
+
+/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
+//#define MIDI_TONE_KEYCODE_OCTAVES 1
+
+/*
+ * HD44780 LCD Display Configuration
+ */
+/*
+#define LCD_LINES           2     //< number of visible lines of the display
+#define LCD_DISP_LENGTH    16     //< visibles characters per line of the display
+
+#define LCD_IO_MODE      1            //< 0: memory mapped mode, 1: IO port mode
+
+#if LCD_IO_MODE
+#define LCD_PORT         PORTB        //< port for the LCD lines
+#define LCD_DATA0_PORT   LCD_PORT     //< port for 4bit data bit 0
+#define LCD_DATA1_PORT   LCD_PORT     //< port for 4bit data bit 1
+#define LCD_DATA2_PORT   LCD_PORT     //< port for 4bit data bit 2
+#define LCD_DATA3_PORT   LCD_PORT     //< port for 4bit data bit 3
+#define LCD_DATA0_PIN    4            //< pin for 4bit data bit 0
+#define LCD_DATA1_PIN    5            //< pin for 4bit data bit 1
+#define LCD_DATA2_PIN    6            //< pin for 4bit data bit 2
+#define LCD_DATA3_PIN    7            //< pin for 4bit data bit 3
+#define LCD_RS_PORT      LCD_PORT     //< port for RS line
+#define LCD_RS_PIN       3            //< pin  for RS line
+#define LCD_RW_PORT      LCD_PORT     //< port for RW line
+#define LCD_RW_PIN       2            //< pin  for RW line
+#define LCD_E_PORT       LCD_PORT     //< port for Enable line
+#define LCD_E_PIN        1            //< pin  for Enable line
+#endif
+*/
+
+/* Bootmagic Lite key configuration */
+// #define BOOTMAGIC_LITE_ROW 0
+// #define BOOTMAGIC_LITE_COLUMN 0

keyboards/foxlab/leaf60/universal/info.json

@@ -0,0 +1,20 @@
+{
+    "keyboard_name": "Fox Lab Leaf60", 
+    "url": "", 
+    "maintainer": "qmk", 
+    "width": 15, 
+    "height": 5, 
+    "layouts": {
+        "LAYOUT_all": {
+            "layout": [{"x":0, "y":0}, {"x":1, "y":0}, {"x":2, "y":0}, {"x":3, "y":0}, {"x":4, "y":0}, {"x":5, "y":0}, {"x":6, "y":0}, {"x":7, "y":0}, {"x":8, "y":0}, {"x":9, "y":0}, {"x":10, "y":0}, {"x":11, "y":0}, {"x":12, "y":0}, {"x":13, "y":0}, {"x":14, "y":0}, {"x":0, "y":1, "w":1.5}, {"x":1.5, "y":1}, {"x":2.5, "y":1}, {"x":3.5, "y":1}, {"x":4.5, "y":1}, {"x":5.5, "y":1}, {"x":6.5, "y":1}, {"x":7.5, "y":1}, {"x":8.5, "y":1}, {"x":9.5, "y":1}, {"x":10.5, "y":1}, {"x":11.5, "y":1}, {"x":12.5, "y":1}, {"x":13.5, "y":1, "w":1.5}, {"x":0, "y":2, "w":1.75}, {"x":1.75, "y":2}, {"x":2.75, "y":2}, {"x":3.75, "y":2}, {"x":4.75, "y":2}, {"x":5.75, "y":2}, {"x":6.75, "y":2}, {"x":7.75, "y":2}, {"x":8.75, "y":2}, {"x":9.75, "y":2}, {"x":10.75, "y":2}, {"x":11.75, "y":2}, {"x":12.75, "y":2, "w":2.25}, {"x":0, "y":3, "w":1.25}, {"x":1.25, "y":3}, {"x":2.25, "y":3}, {"x":3.25, "y":3}, {"x":4.25, "y":3}, {"x":5.25, "y":3}, {"x":6.25, "y":3}, {"x":7.25, "y":3}, {"x":8.25, "y":3}, {"x":9.25, "y":3}, {"x":10.25, "y":3}, {"x":11.25, "y":3}, {"x":12.25, "y":3, "w":1.75}, {"x":14, "y":3}, {"x":0, "y":4, "w":1.25}, {"x":1.25, "y":4, "w":1.25}, {"x":2.5, "y":4, "w":1.25}, {"x":3.75, "y":4, "w":2.25}, {"x":6, "y":4, "w":1.25}, {"x":7.25, "y":4, "w":2.75}, {"x":10, "y":4, "w":1.25}, {"x":11.25, "y":4, "w":1.25}, {"x":12.5, "y":4, "w":1.25}, {"x":13.75, "y":4, "w":1.25}]
+        },
+        
+        "LAYOUT_60_ansi": {
+            "layout": [{"x":0, "y":0}, {"x":1, "y":0}, {"x":2, "y":0}, {"x":3, "y":0}, {"x":4, "y":0}, {"x":5, "y":0}, {"x":6, "y":0}, {"x":7, "y":0}, {"x":8, "y":0}, {"x":9, "y":0}, {"x":10, "y":0}, {"x":11, "y":0}, {"x":12, "y":0}, {"x":13, "y":0, "w":2}, {"x":0, "y":1, "w":1.5}, {"x":1.5, "y":1}, {"x":2.5, "y":1}, {"x":3.5, "y":1}, {"x":4.5, "y":1}, {"x":5.5, "y":1}, {"x":6.5, "y":1}, {"x":7.5, "y":1}, {"x":8.5, "y":1}, {"x":9.5, "y":1}, {"x":10.5, "y":1}, {"x":11.5, "y":1}, {"x":12.5, "y":1}, {"x":13.5, "y":1, "w":1.5}, {"x":0, "y":2, "w":1.75}, {"x":1.75, "y":2}, {"x":2.75, "y":2}, {"x":3.75, "y":2}, {"x":4.75, "y":2}, {"x":5.75, "y":2}, {"x":6.75, "y":2}, {"x":7.75, "y":2}, {"x":8.75, "y":2}, {"x":9.75, "y":2}, {"x":10.75, "y":2}, {"x":11.75, "y":2}, {"x":12.75, "y":2, "w":2.25}, {"x":0, "y":3, "w":2.25}, {"x":2.25, "y":3}, {"x":3.25, "y":3}, {"x":4.25, "y":3}, {"x":5.25, "y":3}, {"x":6.25, "y":3}, {"x":7.25, "y":3}, {"x":8.25, "y":3}, {"x":9.25, "y":3}, {"x":10.25, "y":3}, {"x":11.25, "y":3}, {"x":12.25, "y":3, "w":2.75}, {"x":0, "y":4, "w":1.25}, {"x":1.25, "y":4, "w":1.25}, {"x":2.5, "y":4, "w":1.25}, {"x":3.75, "y":4, "w":6.25}, {"x":10, "y":4, "w":1.25}, {"x":11.25, "y":4, "w":1.25}, {"x":12.5, "y":4, "w":1.25}, {"x":13.75, "y":4, "w":1.25}]
+        },
+
+        "LAYOUT_60_hhkb": {
+            "layout": [{"x":0, "y":0}, {"x":1, "y":0}, {"x":2, "y":0}, {"x":3, "y":0}, {"x":4, "y":0}, {"x":5, "y":0}, {"x":6, "y":0}, {"x":7, "y":0}, {"x":8, "y":0}, {"x":9, "y":0}, {"x":10, "y":0}, {"x":11, "y":0}, {"x":12, "y":0}, {"x":13, "y":0}, {"x":14, "y":0}, {"x":0, "y":1, "w":1.5}, {"x":1.5, "y":1}, {"x":2.5, "y":1}, {"x":3.5, "y":1}, {"x":4.5, "y":1}, {"x":5.5, "y":1}, {"x":6.5, "y":1}, {"x":7.5, "y":1}, {"x":8.5, "y":1}, {"x":9.5, "y":1}, {"x":10.5, "y":1}, {"x":11.5, "y":1}, {"x":12.5, "y":1}, {"x":13.5, "y":1, "w":1.5}, {"x":0, "y":2, "w":1.75}, {"x":1.75, "y":2}, {"x":2.75, "y":2}, {"x":3.75, "y":2}, {"x":4.75, "y":2}, {"x":5.75, "y":2}, {"x":6.75, "y":2}, {"x":7.75, "y":2}, {"x":8.75, "y":2}, {"x":9.75, "y":2}, {"x":10.75, "y":2}, {"x":11.75, "y":2}, {"x":12.75, "y":2, "w":2.25}, {"x":0, "y":3, "w":2.25}, {"x":2.25, "y":3}, {"x":3.25, "y":3}, {"x":4.25, "y":3}, {"x":5.25, "y":3}, {"x":6.25, "y":3}, {"x":7.25, "y":3}, {"x":8.25, "y":3}, {"x":9.25, "y":3}, {"x":10.25, "y":3}, {"x":11.25, "y":3}, {"x":12.25, "y":3, "w":1.75}, {"x":14, "y":3}, {"x":1.5, "y":4}, {"x":2.5, "y":4, "w":1.5}, {"x":4, "y":4, "w":7}, {"x":11, "y":4, "w":1.5}, {"x":12.5, "y":4}]
+        }
+    }
+}

keyboards/foxlab/leaf60/universal/keymaps/default/config.h

@@ -0,0 +1,19 @@
+/* Copyright 2019 Fox Lab
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+
+// place overrides here

keyboards/foxlab/leaf60/universal/keymaps/default/keymap.c

@@ -0,0 +1,46 @@
+/* Copyright 2019 Fox Lab
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include QMK_KEYBOARD_H
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+	LAYOUT_all(
+		KC_ESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_GRV, KC_BSPC,
+		KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS, 
+		KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_ENT, 
+		KC_LSFT, KC_NO, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT, KC_DEL, 
+		KC_LCTL, KC_LGUI, KC_LALT, KC_SPC, KC_SPC, KC_SPC, KC_RALT, MO(1), KC_RGUI, KC_RCTL),
+
+	LAYOUT_all(
+		RESET, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_TRNS, KC_TRNS, 
+		KC_TRNS, BL_TOGG, BL_DEC, BL_INC, BL_STEP, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, 
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, 
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, 
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS)
+
+};
+
+void matrix_init_user(void) {
+
+}
+
+void matrix_scan_user(void) {
+
+}
+
+void led_set_user(uint8_t usb_led) {
+
+}

keyboards/foxlab/leaf60/universal/keymaps/default/readme.md

@@ -0,0 +1 @@
+# The default keymap for Universal Leaf60

keyboards/foxlab/leaf60/universal/readme.md

@@ -0,0 +1,13 @@
+# Fox Lab Leaf60
+
+A 60% gasket sandwich made by Fox Lab.
+
+Keyboard Maintainer: [Fox Lab](https://github.com/fox-lab), [MechMerlin](https://github.com/mechmerlin)  
+Hardware Supported: Leaf60 powered by the ATmega32U4  
+Hardware Availability: [Geekhack Group Buy](https://geekhack.org/index.php?topic=99002.0)  
+
+Make example for this keyboard (after setting up your build environment):
+
+    make foxlab/leaf60/universal:default
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/foxlab/leaf60/universal/rules.mk

@@ -0,0 +1,82 @@
+# MCU name
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   atmega32a    bootloadHID
+BOOTLOADER = atmel-dfu
+
+
+# If you don't know the bootloader type, then you can specify the
+# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
+#   Teensy halfKay      512
+#   Teensy++ halfKay    1024
+#   Atmel DFU loader    4096
+#   LUFA bootloader     4096
+#   USBaspLoader        2048
+# OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE = lite      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = no        # Console for debug(+400)
+COMMAND_ENABLE = no        # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE = no            # USB Nkey Rollover
+BACKLIGHT_ENABLE = yes       # Enable keyboard backlight functionality on B7 by default
+RGBLIGHT_ENABLE = yes        # Enable keyboard RGB underglow
+MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no           # Audio output on port C6
+FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
+HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)
+
+LAYOUTS = 60_ansi 60_hhkb

keyboards/foxlab/leaf60/universal/universal.c

@@ -0,0 +1,61 @@
+/* Copyright 2019 Fox Lab
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include "universal.h"
+
+// Optional override functions below.
+// You can leave any or all of these undefined.
+// These are only required if you want to perform custom actions.
+
+void matrix_init_kb(void) {
+  // put your keyboard start-up code here
+  // runs once when the firmware starts up
+  setPinOutput(E6);
+  matrix_init_user();
+}
+
+/*
+
+void matrix_scan_kb(void) {
+  // put your looping keyboard code here
+  // runs every cycle (a lot)
+
+  matrix_scan_user();
+}
+
+bool process_record_kb(uint16_t keycode, keyrecord_t *record) {
+  // put your per-action keyboard code here
+  // runs for every action, just before processing by the firmware
+
+  return process_record_user(keycode, record);
+}
+
+void led_set_kb(uint8_t usb_led) {
+  // put your keyboard LED indicator (ex: Caps Lock LED) toggling code here
+
+  led_set_user(usb_led);
+}
+
+*/
+
+
+void led_set_kb(uint8_t usb_led) {
+  if (IS_LED_ON(usb_led, USB_LED_CAPS_LOCK)) {
+    writePinLow(E6);
+  } else {
+    writePinHigh(E6);
+  }
+	led_set_user(usb_led);
+}

keyboards/foxlab/leaf60/universal/universal.h

@@ -0,0 +1,68 @@
+/* Copyright 2019 Fox Lab
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#pragma once
+
+#include "quantum.h"
+
+/* This a shortcut to help you visually see your layout.
+ *
+ * The first section contains all of the arguments representing the physical
+ * layout of the board and position of the keys.
+ *
+ * The second converts the arguments into a two-dimensional array which
+ * represents the switch matrix.
+ */
+#define LAYOUT_all( \
+	K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014, \
+	K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113,       \
+	K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211,       K213,       \
+	K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312, K313,       \
+	K400, K401, K402,       K404,       K406,       K408,       K410, K411, K412, K413        \
+) { \
+	{ K000,  K001,  K002,  K003,  K004,  K005,  K006,  K007,  K008,  K009,  K010,  K011,  K012,  K013,  K014 },  \
+	{ K100,  K101,  K102,  K103,  K104,  K105,  K106,  K107,  K108,  K109,  K110,  K111,  K112,  K113,  KC_NO }, \
+	{ K200,  K201,  K202,  K203,  K204,  K205,  K206,  K207,  K208,  K209,  K210,  K211,  KC_NO, K213,  KC_NO }, \
+	{ K300,  K301,  K302,  K303,  K304,  K305,  K306,  K307,  K308,  K309,  K310,  K311,  K312,  K313,  KC_NO }, \
+	{ K400,  K401,  K402,  KC_NO, K404,  KC_NO, K406,  KC_NO, K408,  KC_NO, K410,  K411,  K412,  K413,  KC_NO }  \
+}
+
+#define LAYOUT_60_ansi( \
+	K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K014, \
+	K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, \
+	K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211,       K213, \
+	K300, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312,             \
+	K400, K401, K402,             K406,                   K410, K411, K412, K413        \
+) { \
+	{ K000,  K001,  K002,  K003,  K004,  K005,  K006,  K007,  K008,  K009,  K010,  K011,  K012,  KC_NO, K014 },  \
+	{ K100,  K101,  K102,  K103,  K104,  K105,  K106,  K107,  K108,  K109,  K110,  K111,  K112,  K113,  KC_NO }, \
+	{ K200,  K201,  K202,  K203,  K204,  K205,  K206,  K207,  K208,  K209,  K210,  K211,  KC_NO, K213,  KC_NO }, \
+	{ K300,  KC_NO, K302,  K303,  K304,  K305,  K306,  K307,  K308,  K309,  K310,  K311,  K312,  KC_NO, KC_NO }, \
+	{ K400,  K401,  K402,  KC_NO, KC_NO, KC_NO, K406,  KC_NO, KC_NO, KC_NO, K410,  K411,  K412,  K413,  KC_NO }  \
+}
+
+#define LAYOUT_60_hhkb( \
+	K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014, \
+	K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113,       \
+	K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211,       K213,       \
+	K300,       K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312, K313,       \
+	K401, K402,                         K406,                   K410, K411                    \
+) { \
+	{ K000,  K001,  K002,  K003,  K004,  K005,  K006,  K007,  K008,  K009,  K010,  K011,  K012,  K013,  K014 },  \
+	{ K100,  K101,  K102,  K103,  K104,  K105,  K106,  K107,  K108,  K109,  K110,  K111,  K112,  K113,  KC_NO }, \
+	{ K200,  K201,  K202,  K203,  K204,  K205,  K206,  K207,  K208,  K209,  K210,  K211,  KC_NO, K213,  KC_NO }, \
+	{ K300,  KC_NO, K302,  K303,  K304,  K305,  K306,  K307,  K308,  K309,  K310,  K311,  K312,  K313,  KC_NO }, \
+	{ KC_NO, K401,  K402,  KC_NO, KC_NO, KC_NO, K406,  KC_NO, KC_NO, KC_NO, K410,  K411,  KC_NO, KC_NO, KC_NO }  \
+}

keyboards/ft/mars80/config.h

@@ -0,0 +1,50 @@
+/*
+Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+#include "config_common.h"
+
+#define VENDOR_ID       0x20A0
+#define PRODUCT_ID      0x422D
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    FT
+#define PRODUCT         Mars 8.0
+#define DESCRIPTION     A custom TKL Keyboard
+
+#define RGBLED_NUM 20
+
+#define MATRIX_ROWS 7
+#define MATRIX_COLS 14
+//                        0   1   2   3   4   5   6   7   8   9   A   B   C   D
+#define MATRIX_ROW_PINS { B0, B1, B2, B3, B5, B6, B7 }
+#define MATRIX_COL_PINS { A0, A1, A2, A3, A4, A5, A6, A7, C7, C6, C5, C4, C3, C2 }
+#define UNUSED_PINS     {}
+
+#define DIODE_DIRECTION COL2ROW
+#define DEBOUNCING_DELAY 5
+
+#define NO_BACKLIGHT_CLOCK
+#define BACKLIGHT_LEVELS 1
+#define RGBLIGHT_ANIMATIONS
+
+#define NO_UART 1
+
+/* key combination for magic key command */
+/* defined by default; to change, uncomment and set to the combination you want */
+// #define IS_COMMAND() (get_mods() == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)))
+

keyboards/ft/mars80/info.json

@@ -0,0 +1,16 @@
+{
+    "keyboard_name": "Mars 8.0", 
+    "url": "", 
+    "maintainer": "qmk", 
+    "width": 18.25, 
+    "height": 6.5, 
+    "layouts": {
+        "LAYOUT_tkl_ansi": {
+            "layout": [{"x":0, "y":0}, {"x":2, "y":0}, {"x":3, "y":0}, {"x":4, "y":0}, {"x":5, "y":0}, {"x":6.5, "y":0}, {"x":7.5, "y":0}, {"x":8.5, "y":0}, {"x":9.5, "y":0}, {"x":11, "y":0}, {"x":12, "y":0}, {"x":13, "y":0}, {"x":14, "y":0}, {"x":15.25, "y":0}, {"x":16.25, "y":0}, {"x":17.25, "y":0}, {"x":0, "y":1.5}, {"x":1, "y":1.5}, {"x":2, "y":1.5}, {"x":3, "y":1.5}, {"x":4, "y":1.5}, {"x":5, "y":1.5}, {"x":6, "y":1.5}, {"x":7, "y":1.5}, {"x":8, "y":1.5}, {"x":9, "y":1.5}, {"x":10, "y":1.5}, {"x":11, "y":1.5}, {"x":12, "y":1.5}, {"x":13, "y":1.5, "w":2}, {"x":15.25, "y":1.5}, {"x":16.25, "y":1.5}, {"x":17.25, "y":1.5}, {"x":0, "y":2.5, "w":1.5}, {"x":1.5, "y":2.5}, {"x":2.5, "y":2.5}, {"x":3.5, "y":2.5}, {"x":4.5, "y":2.5}, {"x":5.5, "y":2.5}, {"x":6.5, "y":2.5}, {"x":7.5, "y":2.5}, {"x":8.5, "y":2.5}, {"x":9.5, "y":2.5}, {"x":10.5, "y":2.5}, {"x":11.5, "y":2.5}, {"x":12.5, "y":2.5}, {"x":13.5, "y":2.5, "w":1.5}, {"x":15.25, "y":2.5}, {"x":16.25, "y":2.5}, {"x":17.25, "y":2.5}, {"x":0, "y":3.5, "w":1.75}, {"x":1.75, "y":3.5}, {"x":2.75, "y":3.5}, {"x":3.75, "y":3.5}, {"x":4.75, "y":3.5}, {"x":5.75, "y":3.5}, {"x":6.75, "y":3.5}, {"x":7.75, "y":3.5}, {"x":8.75, "y":3.5}, {"x":9.75, "y":3.5}, {"x":10.75, "y":3.5}, {"x":11.75, "y":3.5}, {"x":12.75, "y":3.5, "w":2.25}, {"x":0, "y":4.5, "w":2.25}, {"x":2.25, "y":4.5}, {"x":3.25, "y":4.5}, {"x":4.25, "y":4.5}, {"x":5.25, "y":4.5}, {"x":6.25, "y":4.5}, {"x":7.25, "y":4.5}, {"x":8.25, "y":4.5}, {"x":9.25, "y":4.5}, {"x":10.25, "y":4.5}, {"x":11.25, "y":4.5}, {"x":12.25, "y":4.5, "w":2.75}, {"x":16.25, "y":4.5}, {"x":0, "y":5.5, "w":1.25}, {"x":1.25, "y":5.5, "w":1.25}, {"x":2.5, "y":5.5, "w":1.25}, {"x":3.75, "y":5.5, "w":6.25}, {"x":10, "y":5.5, "w":1.25}, {"x":11.25, "y":5.5, "w":1.25}, {"x":12.5, "y":5.5, "w":1.25}, {"x":13.75, "y":5.5, "w":1.25}, {"x":15.25, "y":5.5}, {"x":16.25, "y":5.5}, {"x":17.25, "y":5.5}]
+        },
+
+        "LAYOUT_tkl_iso": {
+            "layout": [{"x":0, "y":0}, {"x":2, "y":0}, {"x":3, "y":0}, {"x":4, "y":0}, {"x":5, "y":0}, {"x":6.5, "y":0}, {"x":7.5, "y":0}, {"x":8.5, "y":0}, {"x":9.5, "y":0}, {"x":11, "y":0}, {"x":12, "y":0}, {"x":13, "y":0}, {"x":14, "y":0}, {"x":15.25, "y":0}, {"x":16.25, "y":0}, {"x":17.25, "y":0}, {"x":0, "y":1.5}, {"x":1, "y":1.5}, {"x":2, "y":1.5}, {"x":3, "y":1.5}, {"x":4, "y":1.5}, {"x":5, "y":1.5}, {"x":6, "y":1.5}, {"x":7, "y":1.5}, {"x":8, "y":1.5}, {"x":9, "y":1.5}, {"x":10, "y":1.5}, {"x":11, "y":1.5}, {"x":12, "y":1.5}, {"x":13, "y":1.5, "w":2}, {"x":15.25, "y":1.5}, {"x":16.25, "y":1.5}, {"x":17.25, "y":1.5}, {"x":0, "y":2.5, "w":1.5}, {"x":1.5, "y":2.5}, {"x":2.5, "y":2.5}, {"x":3.5, "y":2.5}, {"x":4.5, "y":2.5}, {"x":5.5, "y":2.5}, {"x":6.5, "y":2.5}, {"x":7.5, "y":2.5}, {"x":8.5, "y":2.5}, {"x":9.5, "y":2.5}, {"x":10.5, "y":2.5}, {"x":11.5, "y":2.5}, {"x":12.5, "y":2.5}, {"x":13.75, "y":2.5, "w":1.25, "h":2}, {"x":15.25, "y":2.5}, {"x":16.25, "y":2.5}, {"x":17.25, "y":2.5}, {"x":0, "y":3.5, "w":1.75}, {"x":1.75, "y":3.5}, {"x":2.75, "y":3.5}, {"x":3.75, "y":3.5}, {"x":4.75, "y":3.5}, {"x":5.75, "y":3.5}, {"x":6.75, "y":3.5}, {"x":7.75, "y":3.5}, {"x":8.75, "y":3.5}, {"x":9.75, "y":3.5}, {"x":10.75, "y":3.5}, {"x":11.75, "y":3.5}, {"x":12.75, "y":3.5}, {"x":0, "y":4.5, "w":1.25}, {"x":1.25, "y":4.5}, {"x":2.25, "y":4.5}, {"x":3.25, "y":4.5}, {"x":4.25, "y":4.5}, {"x":5.25, "y":4.5}, {"x":6.25, "y":4.5}, {"x":7.25, "y":4.5}, {"x":8.25, "y":4.5}, {"x":9.25, "y":4.5}, {"x":10.25, "y":4.5}, {"x":11.25, "y":4.5}, {"x":12.25, "y":4.5, "w":2.75}, {"x":16.25, "y":4.5}, {"x":0, "y":5.5, "w":1.25}, {"x":1.25, "y":5.5, "w":1.25}, {"x":2.5, "y":5.5, "w":1.25}, {"x":3.75, "y":5.5, "w":6.25}, {"x":10, "y":5.5, "w":1.25}, {"x":11.25, "y":5.5, "w":1.25}, {"x":12.5, "y":5.5, "w":1.25}, {"x":13.75, "y":5.5, "w":1.25}, {"x":15.25, "y":5.5}, {"x":16.25, "y":5.5}, {"x":17.25, "y":5.5}]
+        }
+    }
+}

keyboards/ft/mars80/keymaps/default/config.h

@@ -0,0 +1,19 @@
+/* Copyright 2019 MechMerlin
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+
+// place overrides here

keyboards/ft/mars80/keymaps/default/keymap.c

@@ -0,0 +1,75 @@
+/* Copyright 2019 MechMerlin
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include QMK_KEYBOARD_H
+
+// Defines the keycodes used by our macros in process_record_user
+enum custom_keycodes {
+  QMKBEST = SAFE_RANGE,
+  QMKURL
+};
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+    [0] = LAYOUT_tkl_ansi(
+        KC_ESC,           KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,       KC_PSCR, KC_SLCK, KC_BRK,  \
+        KC_GRV,  KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    KC_MINS, KC_EQL,  KC_BSPC,      KC_INS,  KC_HOME, KC_PGUP, \
+        KC_TAB,  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_LBRC, KC_RBRC, KC_BSLS,      KC_DEL,  KC_END,  KC_PGDN, \
+        KC_CAPS, KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN, KC_QUOT,          KC_ENT,                                  \
+        KC_LSFT,          KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH,          KC_RSFT,               KC_UP,            \
+        KC_LCTL, KC_LGUI, KC_LALT,                            KC_SPC,                             KC_RALT, KC_RGUI, MO(1), KC_RCTL,      KC_LEFT, KC_DOWN, KC_RGHT  \
+    ),
+    [1] = LAYOUT_tkl_ansi(
+        _______,          _______, _______, _______, _______, _______, _______, _______, _______, KC_MSTP, KC_MPLY, KC_MPRV, KC_MNXT,      KC_MUTE, KC_VOLD, KC_VOLU, \
+        _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,      _______, _______, _______, \
+        _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,      _______, _______, _______, \
+        _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,          KC_MSEL,                                 \
+        _______,          _______, _______, KC_CALC, _______, _______, _______, _______, _______, _______, _______,          _______,               _______,          \
+        _______, _______, _______,                            _______,                            _______, _______, _______, _______,      _______, _______, _______  \
+    ),
+};
+
+bool process_record_user(uint16_t keycode, keyrecord_t *record) {
+  switch (keycode) {
+    case QMKBEST:
+      if (record->event.pressed) {
+        // when keycode QMKBEST is pressed
+        SEND_STRING("QMK is the best thing ever!");
+      } else {
+        // when keycode QMKBEST is released
+      }
+      break;
+    case QMKURL:
+      if (record->event.pressed) {
+        // when keycode QMKURL is pressed
+        SEND_STRING("https://qmk.fm/" SS_TAP(X_ENTER));
+      } else {
+        // when keycode QMKURL is released
+      }
+      break;
+  }
+  return true;
+}
+
+void matrix_init_user(void) {
+
+}
+
+void matrix_scan_user(void) {
+
+}
+
+void led_set_user(uint8_t usb_led) {
+
+}

keyboards/ft/mars80/keymaps/default/readme.md

@@ -0,0 +1 @@
+# The default keymap for Mars 8.0

keyboards/ft/mars80/mars80.c

@@ -0,0 +1,91 @@
+/* Copyright 2019 MechMerlin
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include "mars80.h"
+
+#include "rgblight.h"
+#include "i2c_master.h"
+#include "quantum.h"
+
+#ifdef RGBLIGHT_ENABLE
+extern rgblight_config_t rgblight_config;
+
+void rgblight_set(void) {
+    if (!rgblight_config.enable) {
+        for (uint8_t i = 0; i < RGBLED_NUM; i++) {
+            led[i].r = 0;
+            led[i].g = 0;
+            led[i].b = 0;
+        }
+    }
+
+    i2c_init();
+    i2c_transmit(0xb0, (uint8_t*)led, 3 * RGBLED_NUM, 100);
+}
+#endif
+
+void matrix_init_kb(void) {
+#ifdef RGBLIGHT_ENABLE
+    if (rgblight_config.enable) {
+        i2c_init();
+        i2c_transmit(0xb0, (uint8_t*)led, 3 * RGBLED_NUM, 100);
+    }
+#endif
+    // call user level keymaps, if any
+    matrix_init_user();
+}
+
+void matrix_scan_kb(void) {
+#ifdef RGBLIGHT_ENABLE
+    rgblight_task();
+#endif
+    matrix_scan_user();
+    /* Nothing else for now. */
+}
+
+__attribute__ ((weak))
+void matrix_scan_user(void) {
+}
+
+void backlight_init_ports(void) {
+    // initialize pins D0, D1, D4 and D6 as output
+    setPinOutput(D0);
+    setPinOutput(D1);
+    setPinOutput(D4);
+    setPinOutput(D6);
+
+    // turn backlight LEDs on
+    writePinHigh(D0);
+    writePinHigh(D1);
+    writePinHigh(D4);
+    writePinHigh(D6);
+}
+
+void backlight_set(uint8_t level) {
+	if (level == 0) {
+        // turn backlight LEDs off
+        writePinLow(D0);
+        writePinLow(D1);
+        writePinLow(D4);
+        writePinLow(D6);
+	} else {
+        // turn backlight LEDs on
+        writePinHigh(D0);
+        writePinHigh(D1);
+        writePinHigh(D4);
+        writePinHigh(D6);
+	}
+}

keyboards/ft/mars80/mars80.h

@@ -0,0 +1,63 @@
+/* Copyright 2019 MechMerlin
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#pragma once
+
+#include "quantum.h"
+
+/* This a shortcut to help you visually see your layout.
+ *
+ * The first section contains all of the arguments representing the physical
+ * layout of the board and position of the keys.
+ *
+ * The second converts the arguments into a two-dimensional array which
+ * represents the switch matrix.
+ */
+
+#define LAYOUT_tkl_iso( \
+    k11, k13, k14, k15, k16, k18, k19, k1A, k1B, k1C, k10, k1D, k12, k02, k03, k00,      \
+    k21, k22, k23, k24, k25, k26, k27, k28, k29, k2A, k2B, k2C, k20, k2D, k07, k06, k05, \
+    k31, k32, k33, k34, k35, k36, k37, k38, k39, k3A, k3B, k3C, k30, k0D, k09, k08,      \
+    k41, k42, k43, k44, k45, k46, k47, k48, k49, k4A, k4B, k4C, k3D, k40,                \
+    k51, k4D, k52, k53, k54, k55, k56, k57, k58, k59, k5A, k5B, k5C, k5D,                \
+    k61, k62, k63, k65, k69, k6A, k6B, k6C, k60, k6D, k68                                \
+) \
+{ \
+   { k00,   KC_NO, k02, k03, KC_NO, k05, k06,   k07,   k08, k09, KC_NO, KC_NO, KC_NO, k0D   }, \
+   { k10,   k11,   k12, k13, k14,   k15, k16,   KC_NO, k18, k19, k1A,   k1B,   k1C,   k1D   }, \
+   { k20,   k21,   k22, k23, k24,   k25, k26,   k27,   k28, k29, k2A,   k2B,   KC_NO, k2D   }, \
+   { k30,   k31,   k32, k33, k34,   k35, k36,   k37,   k38, k39, k3A,   k3B,   k3C,   k3D   }, \
+   { k40,   k41,   k42, k43, k44,   k45, k46,   k47,   k48, k49, k4A,   k4B,   k4C,   k4D   }, \
+   { KC_NO, k51,   k52, k53, k54,   k55, k56,   k57,   k58, k59, k5A,   k5B,   k5C,   k5D   }, \
+   { k60,   k61,   k62, k63, KC_NO, k65, KC_NO, KC_NO, k68, k69, k6A,   k6B,   k6C,   k6D   }, \
+}
+
+#define LAYOUT_tkl_ansi( \
+    k11, k13, k14, k15, k16, k18, k19, k1A, k1B, k1C, k10, k1D, k12, k02, k03, k00,      \
+    k21, k22, k23, k24, k25, k26, k27, k28, k29, k2A, k2B, k2C, k20, k2D, k07, k06, k05, \
+    k31, k32, k33, k34, k35, k36, k37, k38, k39, k3A, k3B, k3C, k30, k3D, k0D, k09, k08, \
+    k41, k42, k43, k44, k45, k46, k47, k48, k49, k4A, k4B, k4C, k40,                     \
+    k51, k52, k53, k54, k55, k56, k57, k58, k59, k5A, k5B, k5C, k5D,                     \
+    k61, k62, k63, k65, k69, k6A, k6B, k6C, k60, k6D, k68                                \
+) \
+{ \
+   { k00,   KC_NO, k02, k03, KC_NO, k05, k06,   k07,   k08, k09, KC_NO, KC_NO, KC_NO, k0D   }, \
+   { k10,   k11,   k12, k13, k14,   k15, k16,   KC_NO, k18, k19, k1A,   k1B,   k1C,   k1D   }, \
+   { k20,   k21,   k22, k23, k24,   k25, k26,   k27,   k28, k29, k2A,   k2B,   KC_NO, k2D   }, \
+   { k30,   k31,   k32, k33, k34,   k35, k36,   k37,   k38, k39, k3A,   k3B,   k3C,   k3D   }, \
+   { k40,   k41,   k42, k43, k44,   k45, k46,   k47,   k48, k49, k4A,   k4B,   k4C,   KC_NO }, \
+   { KC_NO, k51,   k52, k53, k54,   k55, k56,   k57,   k58, k59, k5A,   k5B,   k5C,   k5D   }, \
+   { k60,   k61,   k62, k63, KC_NO, k65, KC_NO, KC_NO, k68, k69, k6A,   k6B,   k6C,   k6D   }, \
+}

keyboards/ft/mars80/readme.md

@@ -0,0 +1,44 @@
+# Mars 8.0
+
+TKL Keyboard with in switch backlight and RGB Underglow. 
+
+Keyboard Maintainer: [MechMerlin](https://github.com/mechmerlin)  
+Hardware Supported: Mars 8.0 PCB  
+Hardware Availability: [Geekhack Group Buy](https://geekhack.org/index.php?topic=93723.0)  
+
+Make example for this keyboard (after setting up your build environment):
+
+    make ft/mars80:default
+
+Flashing
+
+ps2avr(GB) boards use an atmega32a microcontroller and a different bootloader. It is not flashable using the regular QMK methods. 
+
+**Reset Key:** Hold down the key located at `K00`, commonly programmed as `Pause/Break` while plugging in the keyboard.
+
+Windows: 
+1. Download [HIDBootFlash](http://vusb.wikidot.com/project:hidbootflash).
+2. Place your keyboard into reset. 
+3. Press the `Find Device` button and ensure that your keyboard is found.
+4. Press the `Open .hex File` button and locate the `.hex` file you created.
+5. Press the `Flash Device` button and wait for the process to complete. 
+
+macOS:
+1. Install homebrew by typing the following:   
+    ```
+    /usr/bin/ruby -e "$(curl -fsSL https://raw.githubusercontent.com/Homebrew/install/master/install)"
+    ```
+2. Install `crosspack-avr`.  
+    ```
+    brew cask install crosspack-avr
+    ```
+3. Install the following packages:
+    ```
+    brew install python3
+    pip3 install pyusb
+    brew install --HEAD https://raw.githubusercontent.com/robertgzr/homebrew-tap/master/bootloadhid.rb
+    ```
+4. Place your keyboard into reset. 
+5. Flash the board by typing `bootloadHID -r` followed by the path to your `.hex` file. 
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/ft/mars80/rules.mk

@@ -0,0 +1,50 @@
+# Copyright 2019 Luiz Ribeiro <luizribeiro@gmail.com>
+#
+# This program is free software: you can redistribute it and/or modify
+# it under the terms of the GNU General Public License as published by
+# the Free Software Foundation, either version 2 of the License, or
+# (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program.  If not, see <http://www.gnu.org/licenses/>.
+
+# MCU name
+MCU = atmega32a
+PROTOCOL = VUSB
+
+# unsupported features for now
+NO_UART = yes
+NO_SUSPEND_POWER_DOWN = yes
+
+# processor frequency
+F_CPU = 12000000
+
+# Bootloader
+#     This definition is optional, and if your keyboard supports multiple bootloaders of
+#     different sizes, comment this out, and the correct address will be loaded
+#     automatically (+60). See bootloader.mk for all options.
+BOOTLOADER = bootloadHID
+
+# build options
+BOOTMAGIC_ENABLE = no
+MOUSEKEY_ENABLE = no
+EXTRAKEY_ENABLE = yes
+CONSOLE_ENABLE = yes
+COMMAND_ENABLE = yes
+BACKLIGHT_ENABLE = yes
+RGBLIGHT_ENABLE = yes
+RGBLIGHT_CUSTOM_DRIVER = yes
+
+OPT_DEFS = -DDEBUG_LEVEL=0
+
+SRC += i2c_master.c
+
+# programming options
+PROGRAM_CMD = ./util/atmega32a_program.py $(TARGET).hex
+
+LAYOUTS = tkl_ansi tkl_iso

keyboards/ft/mars80/usbconfig.h

@@ -0,0 +1,393 @@
+/* Name: usbconfig.h
+ * Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
+ * Author: Christian Starkjohann
+ * Creation Date: 2005-04-01
+ * Tabsize: 4
+ * Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
+ * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
+ * This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
+ */
+
+#pragma once
+
+#include "config.h"
+
+/*
+General Description:
+This file is an example configuration (with inline documentation) for the USB
+driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
+also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
+wire the lines to any other port, as long as D+ is also wired to INT0 (or any
+other hardware interrupt, as long as it is the highest level interrupt, see
+section at the end of this file).
+*/
+
+/* ---------------------------- Hardware Config ---------------------------- */
+
+#define USB_CFG_IOPORTNAME      D
+/* This is the port where the USB bus is connected. When you configure it to
+ * "B", the registers PORTB, PINB and DDRB will be used.
+ */
+#define USB_CFG_DMINUS_BIT      3
+/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
+ * This may be any bit in the port.
+ */
+#define USB_CFG_DPLUS_BIT       2
+/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
+ * This may be any bit in the port. Please note that D+ must also be connected
+ * to interrupt pin INT0! [You can also use other interrupts, see section
+ * "Optional MCU Description" below, or you can connect D- to the interrupt, as
+ * it is required if you use the USB_COUNT_SOF feature. If you use D- for the
+ * interrupt, the USB interrupt will also be triggered at Start-Of-Frame
+ * markers every millisecond.]
+ */
+#define USB_CFG_CLOCK_KHZ       (F_CPU/1000)
+/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
+ * 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
+ * require no crystal, they tolerate +/- 1% deviation from the nominal
+ * frequency. All other rates require a precision of 2000 ppm and thus a
+ * crystal!
+ * Since F_CPU should be defined to your actual clock rate anyway, you should
+ * not need to modify this setting.
+ */
+#define USB_CFG_CHECK_CRC       0
+/* Define this to 1 if you want that the driver checks integrity of incoming
+ * data packets (CRC checks). CRC checks cost quite a bit of code size and are
+ * currently only available for 18 MHz crystal clock. You must choose
+ * USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
+ */
+
+/* ----------------------- Optional Hardware Config ------------------------ */
+
+/* #define USB_CFG_PULLUP_IOPORTNAME   D */
+/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
+ * V+, you can connect and disconnect the device from firmware by calling
+ * the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
+ * This constant defines the port on which the pullup resistor is connected.
+ */
+/* #define USB_CFG_PULLUP_BIT          4 */
+/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
+ * above) where the 1.5k pullup resistor is connected. See description
+ * above for details.
+ */
+
+/* --------------------------- Functional Range ---------------------------- */
+
+#define USB_CFG_HAVE_INTRIN_ENDPOINT    1
+/* Define this to 1 if you want to compile a version with two endpoints: The
+ * default control endpoint 0 and an interrupt-in endpoint (any other endpoint
+ * number).
+ */
+#define USB_CFG_HAVE_INTRIN_ENDPOINT3   1
+/* Define this to 1 if you want to compile a version with three endpoints: The
+ * default control endpoint 0, an interrupt-in endpoint 3 (or the number
+ * configured below) and a catch-all default interrupt-in endpoint as above.
+ * You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
+ */
+#define USB_CFG_EP3_NUMBER              3
+/* If the so-called endpoint 3 is used, it can now be configured to any other
+ * endpoint number (except 0) with this macro. Default if undefined is 3.
+ */
+/* #define USB_INITIAL_DATATOKEN           USBPID_DATA1 */
+/* The above macro defines the startup condition for data toggling on the
+ * interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
+ * Since the token is toggled BEFORE sending any data, the first packet is
+ * sent with the oposite value of this configuration!
+ */
+#define USB_CFG_IMPLEMENT_HALT          0
+/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
+ * for endpoint 1 (interrupt endpoint). Although you may not need this feature,
+ * it is required by the standard. We have made it a config option because it
+ * bloats the code considerably.
+ */
+#define USB_CFG_SUPPRESS_INTR_CODE      0
+/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
+ * want to send any data over them. If this macro is defined to 1, functions
+ * usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
+ * you need the interrupt-in endpoints in order to comply to an interface
+ * (e.g. HID), but never want to send any data. This option saves a couple
+ * of bytes in flash memory and the transmit buffers in RAM.
+ */
+#define USB_CFG_INTR_POLL_INTERVAL      1
+/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
+ * interval. The value is in milliseconds and must not be less than 10 ms for
+ * low speed devices.
+ */
+#define USB_CFG_IS_SELF_POWERED         0
+/* Define this to 1 if the device has its own power supply. Set it to 0 if the
+ * device is powered from the USB bus.
+ */
+#define USB_CFG_MAX_BUS_POWER           500
+/* Set this variable to the maximum USB bus power consumption of your device.
+ * The value is in milliamperes. [It will be divided by two since USB
+ * communicates power requirements in units of 2 mA.]
+ */
+#define USB_CFG_IMPLEMENT_FN_WRITE      1
+/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
+ * transfers. Set it to 0 if you don't need it and want to save a couple of
+ * bytes.
+ */
+#define USB_CFG_IMPLEMENT_FN_READ       0
+/* Set this to 1 if you need to send control replies which are generated
+ * "on the fly" when usbFunctionRead() is called. If you only want to send
+ * data from a static buffer, set it to 0 and return the data from
+ * usbFunctionSetup(). This saves a couple of bytes.
+ */
+#define USB_CFG_IMPLEMENT_FN_WRITEOUT   0
+/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
+ * You must implement the function usbFunctionWriteOut() which receives all
+ * interrupt/bulk data sent to any endpoint other than 0. The endpoint number
+ * can be found in 'usbRxToken'.
+ */
+#define USB_CFG_HAVE_FLOWCONTROL        0
+/* Define this to 1 if you want flowcontrol over USB data. See the definition
+ * of the macros usbDisableAllRequests() and usbEnableAllRequests() in
+ * usbdrv.h.
+ */
+#define USB_CFG_DRIVER_FLASH_PAGE       0
+/* If the device has more than 64 kBytes of flash, define this to the 64 k page
+ * where the driver's constants (descriptors) are located. Or in other words:
+ * Define this to 1 for boot loaders on the ATMega128.
+ */
+#define USB_CFG_LONG_TRANSFERS          0
+/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
+ * in a single control-in or control-out transfer. Note that the capability
+ * for long transfers increases the driver size.
+ */
+/* #define USB_RX_USER_HOOK(data, len)     if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
+/* This macro is a hook if you want to do unconventional things. If it is
+ * defined, it's inserted at the beginning of received message processing.
+ * If you eat the received message and don't want default processing to
+ * proceed, do a return after doing your things. One possible application
+ * (besides debugging) is to flash a status LED on each packet.
+ */
+/* #define USB_RESET_HOOK(resetStarts)     if(!resetStarts){hadUsbReset();} */
+/* This macro is a hook if you need to know when an USB RESET occurs. It has
+ * one parameter which distinguishes between the start of RESET state and its
+ * end.
+ */
+/* #define USB_SET_ADDRESS_HOOK()              hadAddressAssigned(); */
+/* This macro (if defined) is executed when a USB SET_ADDRESS request was
+ * received.
+ */
+#define USB_COUNT_SOF                   1
+/* define this macro to 1 if you need the global variable "usbSofCount" which
+ * counts SOF packets. This feature requires that the hardware interrupt is
+ * connected to D- instead of D+.
+ */
+/* #ifdef __ASSEMBLER__
+ * macro myAssemblerMacro
+ *     in      YL, TCNT0
+ *     sts     timer0Snapshot, YL
+ *     endm
+ * #endif
+ * #define USB_SOF_HOOK                    myAssemblerMacro
+ * This macro (if defined) is executed in the assembler module when a
+ * Start Of Frame condition is detected. It is recommended to define it to
+ * the name of an assembler macro which is defined here as well so that more
+ * than one assembler instruction can be used. The macro may use the register
+ * YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
+ * immediately after an SOF pulse may be lost and must be retried by the host.
+ * What can you do with this hook? Since the SOF signal occurs exactly every
+ * 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
+ * designs running on the internal RC oscillator.
+ * Please note that Start Of Frame detection works only if D- is wired to the
+ * interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
+ */
+#define USB_CFG_CHECK_DATA_TOGGLING     0
+/* define this macro to 1 if you want to filter out duplicate data packets
+ * sent by the host. Duplicates occur only as a consequence of communication
+ * errors, when the host does not receive an ACK. Please note that you need to
+ * implement the filtering yourself in usbFunctionWriteOut() and
+ * usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
+ * for each control- and out-endpoint to check for duplicate packets.
+ */
+#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH   0
+/* define this macro to 1 if you want the function usbMeasureFrameLength()
+ * compiled in. This function can be used to calibrate the AVR's RC oscillator.
+ */
+#define USB_USE_FAST_CRC                0
+/* The assembler module has two implementations for the CRC algorithm. One is
+ * faster, the other is smaller. This CRC routine is only used for transmitted
+ * messages where timing is not critical. The faster routine needs 31 cycles
+ * per byte while the smaller one needs 61 to 69 cycles. The faster routine
+ * may be worth the 32 bytes bigger code size if you transmit lots of data and
+ * run the AVR close to its limit.
+ */
+
+/* -------------------------- Device Description --------------------------- */
+
+#define USB_CFG_VENDOR_ID       (VENDOR_ID & 0xFF), ((VENDOR_ID >> 8) & 0xFF)
+/* USB vendor ID for the device, low byte first. If you have registered your
+ * own Vendor ID, define it here. Otherwise you may use one of obdev's free
+ * shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
+ * *** IMPORTANT NOTE ***
+ * This template uses obdev's shared VID/PID pair for Vendor Class devices
+ * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
+ * the implications!
+ */
+#define USB_CFG_DEVICE_ID       (PRODUCT_ID & 0xFF), ((PRODUCT_ID >> 8) & 0xFF)
+/* This is the ID of the product, low byte first. It is interpreted in the
+ * scope of the vendor ID. If you have registered your own VID with usb.org
+ * or if you have licensed a PID from somebody else, define it here. Otherwise
+ * you may use one of obdev's free shared VID/PID pairs. See the file
+ * USB-IDs-for-free.txt for details!
+ * *** IMPORTANT NOTE ***
+ * This template uses obdev's shared VID/PID pair for Vendor Class devices
+ * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
+ * the implications!
+ */
+#define USB_CFG_DEVICE_VERSION  0x00, 0x02
+/* Version number of the device: Minor number first, then major number.
+ */
+#define USB_CFG_VENDOR_NAME     'f', 't'
+#define USB_CFG_VENDOR_NAME_LEN 2
+/* These two values define the vendor name returned by the USB device. The name
+ * must be given as a list of characters under single quotes. The characters
+ * are interpreted as Unicode (UTF-16) entities.
+ * If you don't want a vendor name string, undefine these macros.
+ * ALWAYS define a vendor name containing your Internet domain name if you use
+ * obdev's free shared VID/PID pair. See the file USB-IDs-for-free.txt for
+ * details.
+ */
+#define USB_CFG_DEVICE_NAME     'm', 'a', 'r', 's', '8', '0'
+#define USB_CFG_DEVICE_NAME_LEN 6
+/* Same as above for the device name. If you don't want a device name, undefine
+ * the macros. See the file USB-IDs-for-free.txt before you assign a name if
+ * you use a shared VID/PID.
+ */
+/*#define USB_CFG_SERIAL_NUMBER   'N', 'o', 'n', 'e' */
+/*#define USB_CFG_SERIAL_NUMBER_LEN   0 */
+/* Same as above for the serial number. If you don't want a serial number,
+ * undefine the macros.
+ * It may be useful to provide the serial number through other means than at
+ * compile time. See the section about descriptor properties below for how
+ * to fine tune control over USB descriptors such as the string descriptor
+ * for the serial number.
+ */
+#define USB_CFG_DEVICE_CLASS        0
+#define USB_CFG_DEVICE_SUBCLASS     0
+/* See USB specification if you want to conform to an existing device class.
+ * Class 0xff is "vendor specific".
+ */
+#define USB_CFG_INTERFACE_CLASS     3   /* HID */
+#define USB_CFG_INTERFACE_SUBCLASS  1   /* Boot */
+#define USB_CFG_INTERFACE_PROTOCOL  1   /* Keyboard */
+/* See USB specification if you want to conform to an existing device class or
+ * protocol. The following classes must be set at interface level:
+ * HID class is 3, no subclass and protocol required (but may be useful!)
+ * CDC class is 2, use subclass 2 and protocol 1 for ACM
+ */
+#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH    0
+/* Define this to the length of the HID report descriptor, if you implement
+ * an HID device. Otherwise don't define it or define it to 0.
+ * If you use this define, you must add a PROGMEM character array named
+ * "usbHidReportDescriptor" to your code which contains the report descriptor.
+ * Don't forget to keep the array and this define in sync!
+ */
+
+/* #define USB_PUBLIC static */
+/* Use the define above if you #include usbdrv.c instead of linking against it.
+ * This technique saves a couple of bytes in flash memory.
+ */
+
+/* ------------------- Fine Control over USB Descriptors ------------------- */
+/* If you don't want to use the driver's default USB descriptors, you can
+ * provide our own. These can be provided as (1) fixed length static data in
+ * flash memory, (2) fixed length static data in RAM or (3) dynamically at
+ * runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
+ * information about this function.
+ * Descriptor handling is configured through the descriptor's properties. If
+ * no properties are defined or if they are 0, the default descriptor is used.
+ * Possible properties are:
+ *   + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
+ *     at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
+ *     used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
+ *     you want RAM pointers.
+ *   + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
+ *     in static memory is in RAM, not in flash memory.
+ *   + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
+ *     the driver must know the descriptor's length. The descriptor itself is
+ *     found at the address of a well known identifier (see below).
+ * List of static descriptor names (must be declared PROGMEM if in flash):
+ *   char usbDescriptorDevice[];
+ *   char usbDescriptorConfiguration[];
+ *   char usbDescriptorHidReport[];
+ *   char usbDescriptorString0[];
+ *   int usbDescriptorStringVendor[];
+ *   int usbDescriptorStringDevice[];
+ *   int usbDescriptorStringSerialNumber[];
+ * Other descriptors can't be provided statically, they must be provided
+ * dynamically at runtime.
+ *
+ * Descriptor properties are or-ed or added together, e.g.:
+ * #define USB_CFG_DESCR_PROPS_DEVICE   (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
+ *
+ * The following descriptors are defined:
+ *   USB_CFG_DESCR_PROPS_DEVICE
+ *   USB_CFG_DESCR_PROPS_CONFIGURATION
+ *   USB_CFG_DESCR_PROPS_STRINGS
+ *   USB_CFG_DESCR_PROPS_STRING_0
+ *   USB_CFG_DESCR_PROPS_STRING_VENDOR
+ *   USB_CFG_DESCR_PROPS_STRING_PRODUCT
+ *   USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
+ *   USB_CFG_DESCR_PROPS_HID
+ *   USB_CFG_DESCR_PROPS_HID_REPORT
+ *   USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
+ *
+ * Note about string descriptors: String descriptors are not just strings, they
+ * are Unicode strings prefixed with a 2 byte header. Example:
+ * int  serialNumberDescriptor[] = {
+ *     USB_STRING_DESCRIPTOR_HEADER(6),
+ *     'S', 'e', 'r', 'i', 'a', 'l'
+ * };
+ */
+
+#define USB_CFG_DESCR_PROPS_DEVICE                  0
+#define USB_CFG_DESCR_PROPS_CONFIGURATION           USB_PROP_IS_DYNAMIC
+//#define USB_CFG_DESCR_PROPS_CONFIGURATION           0
+#define USB_CFG_DESCR_PROPS_STRINGS                 0
+#define USB_CFG_DESCR_PROPS_STRING_0                0
+#define USB_CFG_DESCR_PROPS_STRING_VENDOR           0
+#define USB_CFG_DESCR_PROPS_STRING_PRODUCT          0
+#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER    0
+#define USB_CFG_DESCR_PROPS_HID                     USB_PROP_IS_DYNAMIC
+//#define USB_CFG_DESCR_PROPS_HID                     0
+#define USB_CFG_DESCR_PROPS_HID_REPORT              USB_PROP_IS_DYNAMIC
+//#define USB_CFG_DESCR_PROPS_HID_REPORT              0
+#define USB_CFG_DESCR_PROPS_UNKNOWN                 0
+
+#define usbMsgPtr_t unsigned short
+/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
+ * a scalar type here because gcc generates slightly shorter code for scalar
+ * arithmetics than for pointer arithmetics. Remove this define for backward
+ * type compatibility or define it to an 8 bit type if you use data in RAM only
+ * and all RAM is below 256 bytes (tiny memory model in IAR CC).
+ */
+
+/* ----------------------- Optional MCU Description ------------------------ */
+
+/* The following configurations have working defaults in usbdrv.h. You
+ * usually don't need to set them explicitly. Only if you want to run
+ * the driver on a device which is not yet supported or with a compiler
+ * which is not fully supported (such as IAR C) or if you use a differnt
+ * interrupt than INT0, you may have to define some of these.
+ */
+/* #define USB_INTR_CFG            MCUCR */
+/* #define USB_INTR_CFG_SET        ((1 << ISC00) | (1 << ISC01)) */
+/* #define USB_INTR_CFG_CLR        0 */
+/* #define USB_INTR_ENABLE         GIMSK */
+/* #define USB_INTR_ENABLE_BIT     INT0 */
+/* #define USB_INTR_PENDING        GIFR */
+/* #define USB_INTR_PENDING_BIT    INTF0 */
+/* #define USB_INTR_VECTOR         INT0_vect */
+
+/* Set INT1 for D- falling edge to count SOF */
+/* #define USB_INTR_CFG            EICRA */
+#define USB_INTR_CFG_SET        ((1 << ISC11) | (0 << ISC10))
+/* #define USB_INTR_CFG_CLR        0 */
+/* #define USB_INTR_ENABLE         EIMSK */
+#define USB_INTR_ENABLE_BIT     INT1
+/* #define USB_INTR_PENDING        EIFR */
+#define USB_INTR_PENDING_BIT    INTF1
+#define USB_INTR_VECTOR         INT1_vect

keyboards/georgi/config.h

@@ -23,7 +23,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 /* Defaults */
 
-#define VERSION "v1.0: Stenoknight"
+#define VERSION "v1.1: ClayM"
 #define VERBOSE
 
 #define FORCE_NKRO

keyboards/georgi/keymaps/colemak-dh/keymap.c

@@ -0,0 +1,306 @@
+/*
+ * Good on you for modifying your layout, this is the most nonQMK layout you will come across
+ * There are three modes, Steno (the default), QWERTY (Toggleable) and a Momentary symbol layer
+ *
+ * Don't modify the steno layer directly, instead add chords using the keycodes and macros
+ * from sten.h to the layout you want to modify.
+ *
+ * Observe the comment above processQWERTY!
+ *
+ * http://docs.gboards.ca
+ */
+
+#include QMK_KEYBOARD_H
+#include "sten.h"
+#include "keymap_steno.h"
+#define IGNORE_MOD_TAP_INTERRUPT
+
+// Steno Layers
+#define FUNCT	( LSD | LK | LP | LH )
+#define MEDIA	( LSD | LK | LW | LR )
+#define MOVE	( LSD | LK )
+#define NUM		( PWR )
+#define SYM		( RZ )
+
+// Keys and chords that, once they appear, are added to every subsequent partial chord
+// until the whole thing is sent.
+uint32_t stenoLayers[] = {NUM, SYM, MOVE, MEDIA, FUNCT};
+
+// QMK Layers
+#define STENO_LAYER   0
+#define GAMING		  1
+#define GAMING_2	  2
+
+/* Keyboard Layout
+ * ,---------------------------------.	  ,------------------------------.
+ * | FN  | LSU | LFT | LP | LH | ST1 |	  | ST3 | RF | RP | RL | RT | RD |
+ * |-----+-----+-----+----+----|-----|	  |-----|----+----+----+----+----|
+ * | PWR | LSD | LK  | LW | LR | ST2 |	  | ST4 | RR | RB | RG | RS | RZ |
+ * `---------------------------------'	  `------------------------------'
+ *					 ,---------------,	  .---------------.
+ *					 | LNO | LA | LO |	  | RE | RU | RNO |
+ *					 `---------------'	  `---------------'
+ */
+
+// Note: You can only use basic keycodes here!
+//
+// P() is just a wrapper to make your life easier.
+// PC() applies the mapping to all of the StenoLayers. For overloading, define these last.
+//
+// FN is unavailable. That is reserved for system use.
+// Chords containing PWR are always available, even in steno mode.
+//
+// http://docs.gboards.ca
+uint32_t processQwerty(bool lookup) {
+	// Special keys
+	P( RT  | RS  | RD  | RZ | LNO,		SEND_STRING(VERSION); SEND_STRING(__DATE__));
+	P( LFT | LK  | LP  | LW,			REPEAT());
+
+	// Mouse Keys
+	/* P( LO  | LSD | LK,	CLICK_MOUSE(KC_MS_BTN2)); */
+	/* P( LO  | LR  | LW,	CLICK_MOUSE(KC_MS_BTN1)); */
+
+
+/* Function layer
+ * ,-----------------------------------,    ,-----------------------------------,
+ * |     |     |     | NCTFUNCTF |     |    |     | F1  | F2  | F3  | F4  |     |
+ * |     +     +     +     +     +     |    |     + F5  + F6  + F7  + F8  +     |
+ * |     | FUNCTFUNC |     |     |     |    |     | F9  | F10 | F11 | F12 |     |
+ * `-----+-----+-----+-----+-----+-----'    `-----+-----+-----+-----+-----+-----'
+*/
+	P( FUNCT | RF,			SEND(KC_F1));
+	P( FUNCT | RP,			SEND(KC_F2));
+	P( FUNCT | RL,			SEND(KC_F3));
+	P( FUNCT | RT,			SEND(KC_F4));
+
+	P( FUNCT | RF | RR,		SEND(KC_F5));
+	P( FUNCT | RP | RB,		SEND(KC_F6));
+	P( FUNCT | RL | RG,		SEND(KC_F7));
+	P( FUNCT | RT | RS,		SEND(KC_F8));
+
+	P( FUNCT | RR,			SEND(KC_F9));
+	P( FUNCT | RG,			SEND(KC_F10));
+	P( FUNCT | RB,			SEND(KC_F11));
+	P( FUNCT | RS,			SEND(KC_F12));
+
+
+/* Movement layer
+ * ,-----------------------------------,    ,-----------------------------------,
+ * |     |     |     |     |     |     |    |     | <-  |  ↓  |  ↑  | ->  |     |
+ * |     +     +     +     +     +     |    |     +     +     +     +     +     |
+ * |     | MOVEMOVEM |     |     |     |    |     | Hm  | PgD | PgU | End |     |
+ * `-----+-----+-----+-----+-----+-----'    `-----+-----+-----+-----+-----+-----'
+*/
+	P( MOVE | RF,			SEND(KC_LEFT));
+	P( MOVE | RP,			SEND(KC_DOWN));
+	P( MOVE | RL,			SEND(KC_UP));
+	P( MOVE | RT,			SEND(KC_RIGHT));
+
+	P( MOVE | RR,			SEND(KC_HOME));
+	P( MOVE | RB,			SEND(KC_PGDN));
+	P( MOVE | RG,			SEND(KC_PGUP));
+	P( MOVE | RS,			SEND(KC_END));
+
+
+/* Media Layer
+ * ,-----------------------------------,    ,-----------------------------------,
+ * |     |     |     |     |     |     |    |     |Prev |Play | PLY |Next | VolU|
+ * |     +     +     +     +     +     |    |     +     +     +     +     +     |
+ * |     | MEDIAMEDIAMEDIAMEDIAM |     |    |     |     |     |     |Mute | VolD|
+ * `-----+-----+-----+-----+-----+-----'    `-----+-----+-----+-----+-----+-----'
+*/
+	P( MEDIA | RF,			SEND(KC_MPRV));
+	P( MEDIA | RP,			SEND(KC_MPLY));
+	P( MEDIA | RL,			SEND(KC_MPLY));
+	P( MEDIA | RT,			SEND(KC_MNXT));
+	P( MEDIA | RD,			SEND(KC_VOLU));
+
+	P( MEDIA | RS,			SEND(KC_MUTE));
+	P( MEDIA | RZ,			SEND(KC_VOLD));
+
+
+/* Numbers
+ * ,-----------------------------------,    ,-----------------------------------,
+ * |     |     |  a  |  b  |  c  |     |    |  :  |  1  |  2  |  3  |  .  |     |
+ * |     +     +  d  +  e  +  f  +     |    |  0  +  4  +  5  +  6  +  -  +     |
+ * | NUM |     |     |     |     |     |    |     |  7  |  8  |  9  |  0  |     |
+ * `-----+-----+-----+-----+-----+-----'    `-----+-----+-----+-----+-----+-----'
+*/
+	P( NUM | LFT,			SEND(KC_A));
+	P( NUM | LP,			SEND(KC_B));
+	P( NUM | LH,			SEND(KC_C));
+	P( NUM | LK,			SEND(KC_D));
+	P( NUM | LW,			SEND(KC_E));
+	P( NUM | LR,			SEND(KC_F));
+
+	// Right hand
+	P( NUM | ST3,			SEND_STRING(":"));
+	P( NUM | RF,			SEND(KC_1));
+	P( NUM | RP,			SEND(KC_2));
+	P( NUM | RL,			SEND(KC_3));
+	P( NUM | RT,			SEND(KC_DOT));
+
+	P( NUM | ST3 | ST4,		SEND(KC_0));
+	P( NUM | RF  | RR,		SEND(KC_4));
+	P( NUM | RP  | RB,		SEND(KC_5));
+	P( NUM | RG  | RL,		SEND(KC_6));
+	P( NUM | RT  | RS,		SEND(KC_MINUS));
+
+	P( NUM | RR,			SEND(KC_7));
+	P( NUM | RB,			SEND(KC_8));
+	P( NUM | RG,			SEND(KC_9));
+	P( NUM | RS,			SEND(KC_0));
+
+
+/* Symbols
+ * ,-----------------------------------,    ,-----------------------------------,
+ * |     |  `  |  [  |  {  |  (  |  <  |    |  >  |  )  |  }  |  ]  |  ?  |     |
+ * |     +  ~  +  -  +  '  +  :  +  _  |    |  \  +  =  +  "  +  +  +  ?  +     |
+ * |     |  !  |  @  |  #  |  $  |  %  |    |  |  |  ^  |  &  |  *  |  ?  | SYM |
+ * `-----+-----+-----+-----+-----+-----'    `-----+-----+-----+-----+-----+-----'
+*/
+	// Left hand
+	P( SYM | LSU,			SEND(KC_GRV));
+	P( SYM | LFT,			SEND(KC_LBRC));
+	P( SYM | LP,			SEND_STRING("{"));
+	P( SYM | LH,			SEND_STRING("("));
+	P( SYM | ST1,			SEND_STRING("<"));
+
+	P( SYM | LSU | LSD,		SEND_STRING("~"));
+	P( SYM | LFT | LK,		SEND(KC_MINS));
+	P( SYM | LP  | LW,		SEND(KC_QUOTE));
+	P( SYM | LH  | LR,		SEND_STRING(":"));
+	P( SYM | ST1 | ST2,		SEND_STRING("_"));
+
+	P( SYM | LSD,			SEND_STRING("!"));
+	P( SYM | LK,			SEND_STRING("@"));
+	P( SYM | LW,			SEND_STRING("#"));
+	P( SYM | LR,			SEND_STRING("$"));
+	P( SYM | ST2,			SEND_STRING("%"));
+
+	// Right hand
+	P( SYM | ST3,			SEND_STRING(">"));
+	P( SYM | RF,			SEND_STRING(")"));
+	P( SYM | RP,			SEND_STRING("}"));
+	P( SYM | RL,			SEND_STRING("]"));
+	P( SYM | RT,			SEND_STRING("?"));
+
+	P( SYM | ST3 | ST4,		SEND(KC_BSLASH));
+	P( SYM | RF  | RR,		SEND(KC_EQUAL));
+	P( SYM | RP  | RB,		SEND_STRING("\""));
+	P( SYM | RG  | RL,		SEND_STRING("+"));
+	P( SYM | RT  | RS,		SEND_STRING("?"));
+
+	P( SYM | ST4,			SEND_STRING("|"));
+	P( SYM | RR,			SEND_STRING("^"));
+	P( SYM | RB,			SEND_STRING("&"));
+	P( SYM | RG,			SEND_STRING("*"));
+	P( SYM | RS,			SEND_STRING("?"));
+
+
+/* Letters
+ * ,-----------------------------------,    ,-----------------------------------,
+ * |     |  Q  |  W  |  F  |  P  |  B  |    |  J  |  L  |  U  |  Y  |  ;  | ctl |
+ * +-----+- A -+- R -+- S -+- T -+- G -|    |- M -+- N -+- E -+- I -+- O -+-----|
+ * | bsp |  Z  |  X  |  C  |  D  |  V  |    |  K  |  H  |  ,  |  .  |  /  | del |
+ * `-----+-----+-----+-----+-----+-----'    `-----+-----+-----+-----+-----+-----'
+ *					   ,---------------,    .---------------.
+ *					   | alt | ent|shfr|    | spc| gui| alt |
+ *					   `---------------'    `---------------'
+*/
+	// Left hand
+	P( LSU,					SEND(KC_Q));
+	P( LFT,					SEND(KC_W));
+	P( LP,					SEND(KC_F));
+	P( LH,					SEND(KC_P));
+	P( ST1,					SEND(KC_B));
+
+	P( LSU | LSD,			SEND(KC_A));
+	P( LFT | LK,			SEND(KC_R));
+	P( LP  | LW,			SEND(KC_S));
+	P( LH  | LR,			SEND(KC_T));
+	P( ST1 | ST2,			SEND(KC_G));
+
+	P( LSD,					SEND(KC_Z));
+	P( LK,					SEND(KC_X));
+	P( LW,					SEND(KC_C));
+	P( LR,					SEND(KC_D));
+	P( ST2,					SEND(KC_V));
+
+	// Right hand
+	P( ST3,					SEND(KC_J));
+	P( RF,					SEND(KC_L));
+	P( RP,					SEND(KC_U));
+	P( RL,					SEND(KC_Y));
+	P( RT,					SEND(KC_SCLN));
+
+	P( ST3 | ST4,			SEND(KC_M));
+	P( RF  | RR,			SEND(KC_N));
+	P( RP  | RB,			SEND(KC_E));
+	P( RG  | RL,			SEND(KC_I));
+	P( RT  | RS,			SEND(KC_O));
+
+	P( ST4,					SEND(KC_K));
+	P( RR,					SEND(KC_H));
+	P( RB,					SEND(KC_COMM));
+	P( RG,					SEND(KC_DOT));
+	P( RS,					SEND(KC_SLSH));
+
+	// Thumb Chords and modifiers
+	//
+	PC( LNO | RNO | LA | RU,		SEND(KC_LCTL); SEND(KC_LSFT));
+	PC( LNO | LA  | RE,				SEND(KC_LCTL); SEND(KC_LSFT); SEND(KC_LALT));
+
+	// overrides
+	P( PWR | LO,			SEND(KC_LSFT); SEND(KC_BSPC));
+	P( PWR | RD,			SEND(KC_LCTL); SEND(KC_BSPC));
+	P( RZ | RD,				SEND(KC_LCTL); SEND(KC_DEL));
+
+	PC( LNO | LA | LO,		SEND(KC_LSFT); SEND(KC_ESC));
+	PC( LA | LO,			SEND(KC_ESC));
+	PC( LNO,				SEND(KC_LALT));
+	PC( LA,					SEND(KC_ENT));
+	PC( LO,					SEND(KC_LSFT));
+
+	PC( RNO,				SEND(KC_RALT));
+	PC( RE | RU,			SEND(KC_TAB));
+	PC( RE,					SEND(KC_SPC));
+	PC( RU,					SEND(KC_LGUI));
+   
+	PC( PWR,				SEND(KC_BSPC));
+	PC( RD,					SEND(KC_LCTL));
+	P( RZ,					SEND(KC_DEL));
+
+	return 0;
+}
+
+// "Layers"
+// Steno layer should be first in your map.
+// When PWR | FN | ST3 | ST4 is pressed, the layer is increased to the next map. You must return to STENO_LAYER at the end.
+// If you need more space for chords, remove the two gaming layers.
+// Note: If using NO_ACTION_TAPPING, LT will not work!
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+	// Main layer, everything goes through here
+	[STENO_LAYER] = LAYOUT_georgi(
+			STN_FN,  STN_S1,  STN_TL,  STN_PL,	STN_HL,  STN_ST1,		STN_ST3, STN_FR,  STN_PR,  STN_LR,	STN_TR,  STN_DR,
+			STN_PWR, STN_S2,  STN_KL,  STN_WL,	STN_RL,  STN_ST2,		STN_ST4, STN_RR,  STN_BR,  STN_GR,	STN_SR,  STN_ZR,
+								   STN_N1,		STN_A,	 STN_O,			STN_E,	 STN_U,   STN_N7
+	),
+	// Gaming layer with Numpad, Very limited
+	[GAMING] = LAYOUT_georgi(
+		KC_LSFT, KC_Q,	  KC_W,    KC_E,	KC_R,	 KC_T,						 KC_Y,	  KC_U,    KC_I,	KC_O,	 KC_P,	  KC_ENT,
+		KC_LCTL, KC_A,	  KC_S,    KC_D,	KC_F,	 KC_G,						 KC_H,	  KC_J,    KC_K,	KC_L,	 KC_SCLN, KC_DQUO,
+								   KC_LALT, KC_SPC,  LT(GAMING_2, KC_ENT),		 KC_DEL,  KC_ASTR, TO(STENO_LAYER)
+	),
+
+	[GAMING_2] = LAYOUT_georgi(
+		KC_LSFT, KC_1,	  KC_2,    KC_3,	KC_4,	 KC_5,			KC_6,	 KC_7,	  KC_8,    KC_9,	KC_0,	 KC_MINS,
+		KC_LCTL, KC_Z,	  KC_X,    KC_C,	KC_V,	 KC_B,			KC_N,	 KC_M,	  KC_LT,   KC_GT,	KC_QUES, KC_RSFT,
+								   KC_LALT, KC_SPC,  KC_ENT,		KC_DEL,  KC_ASTR, TO(STENO_LAYER)
+	)
+};
+
+// Don't fuck with this, thanks.
+size_t keymapsCount  = sizeof(keymaps)/sizeof(keymaps[0]);
+size_t stenoLayerCount = sizeof(stenoLayers)/sizeof(stenoLayers[0]);

keyboards/georgi/keymaps/colemak-dh/readme.md

@@ -0,0 +1,11 @@
+# Georgi QWERTY/Steno firmware
+
+This is the default keymap for Georgi, it's based heavily off of the naps62 ErgoDox and the Gergo layout. 
+It is both a ergonomic and programmer friendly keymap.
+
+Ideally you should copy this directory and make your changes there. If you come up with a good layout submit a PR!
+
+## Space issues
+If you find yourself running out of space for dictionary entries, disabling mousekeys in rules.mk will save
+you about 4k for entries!
+Get a free 1k by deleting the Gaming layers from the keymap!

keyboards/georgi/keymaps/colemak-dh/rules.mk

@@ -0,0 +1,45 @@
+#----------------------------------------------------------------------------
+# make georgi:claymager:dfu
+# Make sure you have dfu-programmer installed!
+#----------------------------------------------------------------------------
+
+NO_REPEAT				 = yes
+VERBOSE					 = yes
+KEYBOARD_SHARED_EP       = yes
+CUSTOM_MATRIX			 = yes
+STENO_LAYERS			 = yes
+
+#Firmware reduction options
+MOUSEKEY_ENABLE			 = yes 		# 1500 bytes
+NO_TAPPING				 = no 	    # 2000 bytes
+NO_PRINT				 = yes
+
+#Debug options
+CONSOLE_ENABLE			 = no
+DEBUG_MATRIX_SCAN_RATE   = no
+DEBUG_MATRIX			 = no
+ONLY_QWERTY				 = no
+
+# A bunch of stuff that you shouldn't touch unless you
+# know what you're doing.
+#
+# No touchy, capiche?
+SRC += matrix.c i2c_master.c
+ifeq ($(strip $(DEBUG_MATRIX)), yes)
+    OPT_DEFS += -DDEBUG_MATRIX
+endif
+ifeq ($(strip $(NO_REPEAT)), yes)
+    OPT_DEFS += -DNO_REPEAT
+endif
+ifeq ($(strip $(NO_PRINT)), yes)
+    OPT_DEFS += -DNO_PRINT -DNO_DEBUG
+endif
+ifeq ($(strip $(ONLY_QWERTY)), yes)
+    OPT_DEFS += -DONLYQWERTY
+endif
+ifeq ($(strip $(NO_TAPPING)), yes)
+    OPT_DEFS += -DNO_ACTION_TAPPING
+endif
+ifeq ($(strip $(STENO_LAYERS)), yes)
+    OPT_DEFS += -DSTENOLAYERS
+endif

keyboards/georgi/keymaps/default/keymap.c

@@ -38,6 +38,12 @@
 
 // Note: You can only use basic keycodes here!
 // P() is just a wrapper to make your life easier.
+// PC() applies the mapping to all of the StenoLayers.
+//   To overload, declare it with P() first.
+//   Be sure to enable in rules.mk and see colemak-dh for usage 
+//
+// FN is unavailable. That is reserved for system use.
+// Chords containing PWR are always available, even in steno mode.
 //
 // http://docs.gboards.ca
 uint32_t processQwerty(bool lookup) {
@@ -135,7 +141,7 @@ uint32_t processQwerty(bool lookup) {
     P( RZ,          SEND(KC_ESC));
 
     // Symbols and Numbers
-    P( PWR | RE | RU,      SEND(KC_ENT));
+ 	P( PWR | RE | RU,      SEND(KC_ENT));
     P( PWR | LA | LO,      SEND(KC_SPC));
     P( PWR | LP | LW,      SEND(KC_LSFT); SEND(KC_9));       // (
     P( PWR | LH | LR,      SEND(KC_LSFT); SEND(KC_0));       // )
@@ -169,6 +175,10 @@ uint32_t processQwerty(bool lookup) {
     P( PWR | RE,           SEND(KC_SCLN));
     P( PWR | RU,           SEND(KC_BSLS));
     P( PWR | LNO,          SEND(KC_BSLS));
+    P( PWR | RF | RR,      SEND(KC_LEFT));
+    P( PWR | RP | RB,      SEND(KC_DOWN));
+    P( PWR | RL | RG,      SEND(KC_UP));
+    P( PWR | RT | RS,      SEND(KC_RIGHT));
 
     // Letters
     P( LSU | LSD,    SEND(KC_A));

keyboards/georgi/keymaps/default/rules.mk

@@ -7,6 +7,7 @@ NO_REPEAT				 = no
 VERBOSE					 = yes
 KEYBOARD_SHARED_EP       = yes
 CUSTOM_MATRIX			 = yes
+STENO_LAYERS			 = no
 
 #Firmware reduction options
 MOUSEKEY_ENABLE			 = yes 		# 1500 bytes

keyboards/georgi/matrix.c

@@ -1,8 +1,4 @@
 /*
-Note for ErgoDox EZ customizers: Here be dragons!
-This is not a file you want to be messing with.
-All of the interesting stuff for you is under keymaps/ :)
-Love, Erez
 
 Copyright 2013 Oleg Kostyuk <cub.uanic@gmail.com>
 
@@ -248,8 +244,8 @@ uint8_t matrix_scan(void)
     matrix_scan_quantum();
 
 #ifdef DEBUG_MATRIX
-    for (uint8_t c = 0; c < MATRIX_COLS; c++) 
-		for (uint8_t r = 0; r < MATRIX_ROWS; r++) 
+    for (uint8_t c = 0; c < MATRIX_COLS; c++)
+		for (uint8_t r = 0; r < MATRIX_ROWS; r++)
 		  if (matrix_is_on(r, c)) xprintf("r:%d c:%d \n", r, c);
 #endif
 
@@ -359,7 +355,7 @@ static void select_row(uint8_t row)
     if (row < 7) {
         // select on mcp23018
         if (mcp23018_status) { // do nothing on error
-        } else { // set active row low  : 0 // set other rows hi-Z : 1 
+        } else { // set active row low  : 0 // set other rows hi-Z : 1
             mcp23018_status = i2c_start(I2C_ADDR_WRITE, ERGODOX_EZ_I2C_TIMEOUT);        if (mcp23018_status) goto out;
             mcp23018_status = i2c_write(GPIOA, ERGODOX_EZ_I2C_TIMEOUT);                 if (mcp23018_status) goto out;
             mcp23018_status = i2c_write(0xFF & ~(1<<row), ERGODOX_EZ_I2C_TIMEOUT);      if (mcp23018_status) goto out;

keyboards/georgi/sten.c

@@ -11,6 +11,18 @@ uint32_t pChord 		= 0;		// Previous Chord
 int		 pChordIndex 	= 0;		// Keys in previousachord
 uint32_t pChordState[32];			// Previous chord sate 
 uint32_t stickyBits = 0;			// Or'd with every incoming press
+#ifndef NO_DEBUG
+char debugMsg[32];
+#endif
+
+// StenoLayer
+uint32_t releasedChord	= 0;		// Keys released from current chord
+uint32_t tChord			= 0;		// Protects state of cChord
+
+#ifndef STENOLAYERS
+uint32_t stenoLayers[] = { PWR };
+size_t 	 stenoLayerCount = sizeof(stenoLayers)/sizeof(stenoLayers[0]);
+#endif
 
 // Mode state
 enum MODE { STENO = 0, QWERTY, COMMAND };

keyboards/georgi/sten.h

@@ -13,6 +13,9 @@
 
 extern size_t keymapsCount;			// Total keymaps
 extern uint32_t cChord;				// Current Chord
+extern uint32_t stenoLayers[];		// Chords that simulate QMK layers
+extern size_t stenoLayerCount;		// Number of simulated layers
+uint32_t refChord;					// Reference chord for PC macro
 
 // Function defs
 void 			processChord(bool useFakeSteno);
@@ -30,6 +33,11 @@ void 			CLICK_MOUSE(uint8_t);
 
 // Keymap helper
 #define P(chord, act) if (cChord == (chord)) { if (!lookup) {act;} return chord;}
+#define PC(chord, act) if (cChord == (chord)) { if (!lookup) {act;} return chord;} \
+	for(int i = 0; i < stenoLayerCount; i++) { \
+		refChord = stenoLayers[i] | chord; \
+		if (cChord == (refChord)) { if (!lookup) {act;} return refChord;}; \
+}
 
 // Shift to internal representation
 // i.e) S(teno)R(ight)F

keyboards/gergo/matrix.c

@@ -1,8 +1,4 @@
 /*
-Note for ErgoDox EZ customizers: Here be dragons!
-This is not a file you want to be messing with.
-All of the interesting stuff for you is under keymaps/ :)
-Love, Erez
 
 Copyright 2013 Oleg Kostyuk <cub.uanic@gmail.com>
 

keyboards/halberd/config.h

@@ -0,0 +1,232 @@
+/* Copyright 2019 ENDO Katsuhiro <ka2hiro@kagizaraya.jp>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0xFEED
+#define PRODUCT_ID      0x0000
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    Kagizaraya
+#define PRODUCT         Halberd
+#define DESCRIPTION     40% keyboard
+
+/* key matrix size */
+#define MATRIX_ROWS 4
+#define MATRIX_COLS 11
+
+/*
+ * Keyboard Matrix Assignments
+ *
+ * Change this to how you wired your keyboard
+ * COLS: AVR pins used for columns, left to right
+ * ROWS: AVR pins used for rows, top to bottom
+ * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
+ *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
+ *
+*/
+#define MATRIX_ROW_PINS { D6, D4, D5, E6 }
+#define MATRIX_COL_PINS { D7, B4, C7, C6, B6, B5, F7, F6, F5, F4, F1 }
+#define UNUSED_PINS
+
+/* COL2ROW, ROW2COL, or CUSTOM_MATRIX */
+#define DIODE_DIRECTION COL2ROW
+
+// #define BACKLIGHT_PIN B7
+// #define BACKLIGHT_BREATHING
+// #define BACKLIGHT_LEVELS 3
+
+#define RGB_DI_PIN F0
+#ifdef RGB_DI_PIN
+#define RGBLIGHT_ANIMATIONS
+#define RGBLED_NUM 40
+#define RGBLIGHT_HUE_STEP 8
+#define RGBLIGHT_SAT_STEP 8
+#define RGBLIGHT_VAL_STEP 8
+#endif
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCING_DELAY 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/* If defined, GRAVE_ESC will always act as ESC when CTRL is held.
+ * This is userful for the Windows task manager shortcut (ctrl+shift+esc).
+ */
+// #define GRAVE_ESC_CTRL_OVERRIDE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/* key combination for magic key command */
+/*
+#define IS_COMMAND() ( \
+    keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
+)
+*/
+
+/* control how magic key switches layers */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
+
+/* override magic key keymap */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
+//#define MAGIC_KEY_HELP1          H
+//#define MAGIC_KEY_HELP2          SLASH
+//#define MAGIC_KEY_DEBUG          D
+//#define MAGIC_KEY_DEBUG_MATRIX   X
+//#define MAGIC_KEY_DEBUG_KBD      K
+//#define MAGIC_KEY_DEBUG_MOUSE    M
+//#define MAGIC_KEY_VERSION        V
+//#define MAGIC_KEY_STATUS         S
+//#define MAGIC_KEY_CONSOLE        C
+//#define MAGIC_KEY_LAYER0_ALT1    ESC
+//#define MAGIC_KEY_LAYER0_ALT2    GRAVE
+//#define MAGIC_KEY_LAYER0         0
+//#define MAGIC_KEY_LAYER1         1
+//#define MAGIC_KEY_LAYER2         2
+//#define MAGIC_KEY_LAYER3         3
+//#define MAGIC_KEY_LAYER4         4
+//#define MAGIC_KEY_LAYER5         5
+//#define MAGIC_KEY_LAYER6         6
+//#define MAGIC_KEY_LAYER7         7
+//#define MAGIC_KEY_LAYER8         8
+//#define MAGIC_KEY_LAYER9         9
+//#define MAGIC_KEY_BOOTLOADER     PAUSE
+//#define MAGIC_KEY_LOCK           CAPS
+//#define MAGIC_KEY_EEPROM         E
+//#define MAGIC_KEY_NKRO           N
+//#define MAGIC_KEY_SLEEP_LED      Z
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+/*
+ * MIDI options
+ */
+
+/* Prevent use of disabled MIDI features in the keymap */
+//#define MIDI_ENABLE_STRICT 1
+
+/* enable basic MIDI features:
+   - MIDI notes can be sent when in Music mode is on
+*/
+//#define MIDI_BASIC
+
+/* enable advanced MIDI features:
+   - MIDI notes can be added to the keymap
+   - Octave shift and transpose
+   - Virtual sustain, portamento, and modulation wheel
+   - etc.
+*/
+//#define MIDI_ADVANCED
+
+/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
+//#define MIDI_TONE_KEYCODE_OCTAVES 1
+
+/*
+ * HD44780 LCD Display Configuration
+ */
+/*
+#define LCD_LINES           2     //< number of visible lines of the display
+#define LCD_DISP_LENGTH    16     //< visibles characters per line of the display
+
+#define LCD_IO_MODE      1            //< 0: memory mapped mode, 1: IO port mode
+
+#if LCD_IO_MODE
+#define LCD_PORT         PORTB        //< port for the LCD lines
+#define LCD_DATA0_PORT   LCD_PORT     //< port for 4bit data bit 0
+#define LCD_DATA1_PORT   LCD_PORT     //< port for 4bit data bit 1
+#define LCD_DATA2_PORT   LCD_PORT     //< port for 4bit data bit 2
+#define LCD_DATA3_PORT   LCD_PORT     //< port for 4bit data bit 3
+#define LCD_DATA0_PIN    4            //< pin for 4bit data bit 0
+#define LCD_DATA1_PIN    5            //< pin for 4bit data bit 1
+#define LCD_DATA2_PIN    6            //< pin for 4bit data bit 2
+#define LCD_DATA3_PIN    7            //< pin for 4bit data bit 3
+#define LCD_RS_PORT      LCD_PORT     //< port for RS line
+#define LCD_RS_PIN       3            //< pin  for RS line
+#define LCD_RW_PORT      LCD_PORT     //< port for RW line
+#define LCD_RW_PIN       2            //< pin  for RW line
+#define LCD_E_PORT       LCD_PORT     //< port for Enable line
+#define LCD_E_PIN        1            //< pin  for Enable line
+#endif
+*/
+
+/* Bootmagic Lite key configuration */
+// #define BOOTMAGIC_LITE_ROW 0
+// #define BOOTMAGIC_LITE_COLUMN 0
+
+#define TAPPING_TERM    100
+
+

keyboards/halberd/halberd.c

@@ -0,0 +1,43 @@
+/* Copyright 2019 ENDO Katsuhiro <ka2hiro@kagizaraya.jp>
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include "halberd.h"
+
+void matrix_init_kb(void) {
+	// put your keyboard start-up code here
+	// runs once when the firmware starts up
+
+	matrix_init_user();
+}
+
+void matrix_scan_kb(void) {
+	// put your looping keyboard code here
+	// runs every cycle (a lot)
+
+	matrix_scan_user();
+}
+
+bool process_record_kb(uint16_t keycode, keyrecord_t *record) {
+	// put your per-action keyboard code here
+	// runs for every action, just before processing by the firmware
+
+	return process_record_user(keycode, record);
+}
+
+void led_set_kb(uint8_t usb_led) {
+	// put your keyboard LED indicator (ex: Caps Lock LED) toggling code here
+
+	led_set_user(usb_led);
+}

keyboards/halberd/halberd.h

@@ -0,0 +1,40 @@
+/* Copyright 2019 ENDO Katsuhiro <ka2hiro@kagizaraya.jp>
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#pragma once
+
+#include "quantum.h"
+
+/* This a shortcut to help you visually see your layout.
+ *
+ * The first section contains all of the arguments representing the physical
+ * layout of the board and position of the keys.
+ *
+ * The second converts the arguments into a two-dimensional array which
+ * represents the switch matrix.
+ */
+#define LAYOUT( \
+    K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K10, \
+    K11, K12, K13, K14, K15, K16, K17, K18, K19, K20, K21, \
+    K22, K23, K24, K25, K26, K27, K28, K29, K30, K31, K32, \
+              K33, K34, K35, K36, K37, K38, K39   \
+) \
+{ \
+    { K00,   K01,   K02,   K03,   K04,   K05,   K06,   K07,   K08,   K09,   K10 }, \
+    { K11,   K12,   K13,   K14,   K15,   K16,   K17,   K18,   K19,   K20,   K21 }, \
+    { K22,   K23,   K24,   K25,   K26,   K27,   K28,   K29,   K30,   K31,   K32 }, \
+    { KC_NO, KC_NO, K33,   K34,   K35,   K36,   K37,   K38,   K39,   KC_NO, KC_NO } \
+}
+

keyboards/halberd/info.json

@@ -0,0 +1,13 @@
+{
+    "keyboard_name": "Halberd", 
+    "url": "", 
+    "maintainer": "ka2hiro", 
+    "width": 11, 
+    "height": 4, 
+    "layouts": {
+        "LAYOUT": {
+            "layout": [{"label":"!", "x":0, "y":0}, {"label":"@", "x":1, "y":0}, {"label":"#", "x":2, "y":0}, {"label":"$", "x":3, "y":0}, {"label":"%", "x":4, "y":0}, {"label":"Tab", "x":5, "y":0}, {"label":"^", "x":6, "y":0}, {"label":"&", "x":7, "y":0}, {"label":"*", "x":8, "y":0}, {"label":"(", "x":9, "y":0}, {"label":")", "x":10, "y":0}, {"label":"Tab", "x":0, "y":1}, {"label":"_", "x":1, "y":1}, {"label":"+", "x":2, "y":1}, {"label":"|", "x":3, "y":1}, {"label":"~", "x":4, "y":1}, {"label":"BkSp", "x":5, "y":1}, {"label":":", "x":6, "y":1}, {"label":"\"", "x":7, "y":1}, {"label":">", "x":8, "y":1}, {"label":"{", "x":9, "y":1}, {"label":"}", "x":10, "y":1}, {"label":"Caps", "x":0, "y":2}, {"label":"-", "x":1, "y":2}, {"label":"=", "x":2, "y":2}, {"label":"\\", "x":3, "y":2}, {"label":"`", "x":4, "y":2}, {"label":"Enter", "x":5, "y":2}, {"label":";", "x":6, "y":2}, {"label":"'", "x":7, "y":2}, {"label":"<", "x":8, "y":2}, {"label":"[", "x":9, "y":2}, {"label":"]", "x":10, "y":2}, {"label":"GUI", "x":2, "y":3}, {"label":"Lower", "x":3, "y":3}, {"label":"Esc", "x":4, "y":3}, {"x":5, "y":3}, {"label":"Shift", "x":6, "y":3}, {"label":"Raise", "x":7, "y":3}, {"label":"Alt", "x":8, "y":3}]
+        }
+    }
+}
+

keyboards/halberd/keymaps/default/config.h

@@ -0,0 +1,19 @@
+/* Copyright 2019 ENDO Katsuhiro <ka2hiro@kagizaraya.jp>
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+
+// place overrides here

keyboards/halberd/keymaps/default/keymap.c

@@ -0,0 +1,160 @@
+/* Copyright 2019 ENDO Katsuhiro <ka2hiro@kagizaraya.jp>
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include QMK_KEYBOARD_H
+
+// Defines the keycodes used by our macros in process_record_user
+enum layer_names {
+    _QWERTY,
+    _LOWER,
+    _RAISE,
+    _ADJUST,
+};
+
+// Defines the keycodes used by our macros in process_record_user
+enum custom_keycodes {
+  QWERTY = SAFE_RANGE,
+  LOWER,
+  RAISE,
+  ADJUST,
+};
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+/* Qwerty
+ *
+ * ,----------------------------------------------------------------------------.
+ * |   Q  |   W  |   E  |   R  |   T  |  Tab |   Y  |   U  |   I  |   O  |   P  |
+ * |------+------+------+------+------|------|------+------+------+------+------|
+ * |   A  |   S  |   D  |   F  |   G  | BkSp |   H  |   J  |   K  |   L  |   ;  |
+ * |------+------+------+------+------|------|------+------+------+------+------|
+ * |   Z  |   X  |   C  |   V  |   B  | Enter|   N  |   M  |   ,  |   .  |   /  |
+ * `-------------+------+------+------|------|------+------+------+------+------'
+ *               | GUI  | LOWER|Ctrl/Esc|Space|Shift| RAISE| Alt |
+ *               `------------------------------------------------'
+ */
+[_QWERTY] = LAYOUT(
+  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_TAB,     KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,
+  KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_BSPC,     KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN,
+  KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_ENT,     KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH,
+                    KC_LGUI, LOWER, MT(MOD_LCTL, KC_ESC),  KC_SPC, KC_LSFT, RAISE, KC_LALT
+),
+
+/* Raise
+ *
+ * ,----------------------------------------------------------------------------.
+ * |   !  |   @  |   #  |   $  |   %  |      |   ^  |   &  |   *  |   (  |   )  |
+ * |------+------+------+------+------|------|------+------+------+------+------|
+ * |  Tab |   _  |   +  |  |   |  ~   |      |   :  |   "  |   >  |   {  |   }  |
+ * |------+------+------+------+------|------|------+------+------+------+------|
+ * |  Caps|   -  |   =  |  \   |  `   |      |   ;  |   '  |   <  |   [  |   ]  |
+ * `-------------+------+------+------|------|------+------+------+------+------'
+ *               |      | LOWER|      |      |  Esc | RAISE|      |
+ *               `------------------------------------------------'
+ */
+[_RAISE] = LAYOUT(
+  KC_EXLM, KC_AT,   KC_HASH, KC_DLR,  KC_PERC, _______, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN,
+  KC_TAB,  KC_UNDS, KC_PLUS, KC_PIPE, KC_TILD, _______, KC_COLN, KC_DQUO, KC_GT,   KC_LCBR, KC_RCBR,
+  KC_CAPS, KC_MINS, KC_EQL,  KC_BSLS, KC_GRV,  _______, KC_SCLN, KC_QUOT, KC_LT,   KC_LBRC, KC_RBRC,
+                    _______, _______, _______, _______, _______,  _______, _______
+),
+
+/* Lower
+ *
+ * ,----------------------------------------------------------------------------.
+ * |   1  |   2  |   3  |   4  |   5  |      |   6  |   7  |   8  |   9  |   0  |
+ * |------+------+------+------+------|------|------+------+------+------+------|
+ * |  Tab |      |      |      |Enter |      | Left | Down |  Up  | Right| Enter|
+ * |------+------+------+------+------|------|------+------+------+------+------|
+ * |  Ctrl|      |  GUI |  Alt | Del  |      | BkSp | PgUp | PgDn |      |      |
+ * `-------------+------+------+------|------|------+------+------+------+------'
+ *               |      | LOWER|      |      |      | RAISE|      |
+ *               `------------------------------------------------'
+ */
+[_LOWER] = LAYOUT(
+  KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    _______, KC_6,    KC_7,    KC_8,    KC_9,    KC_0,
+  KC_TAB,  _______, _______, _______, KC_ENT,  _______, KC_LEFT, KC_DOWN, KC_UP,   KC_RGHT, KC_ENT,
+  KC_LCTL, _______, KC_LGUI, KC_LALT, KC_DEL,  _______, KC_BSPC, KC_PGUP, KC_PGDN, _______, _______,
+                    _______, _______, _______, _______, _______, _______, _______
+),
+
+
+/* Adjust (Lower + Raise)
+ *
+ * ,----------------------------------------------------------------------------.
+ * |  F1  |  F2  |  F3  |  F4  |  F5  |      |   F6 |  F7  |  F8  |  F9  |  F10 |
+ * |------+------+------+------+------|------|------+------+------+------+------|
+ * |  F11 |  F12 |      |RGBSAI|RGBSAD|      |RGBVAI|RGBVAD|      |      |      |
+ * |------+------+------+------+------|------|------+------+------+------+------|
+ * | Reset|RGBTOG|RGBMOD|RGBHUI|RGBHUD|      | Prev | Next | Vol- | Vol+ | Play |
+ * `-------------+------+------+------|------|------+------+------+------+------'
+ *               |      | LOWER|      |      |      | RAISE|      |
+ *               `------------------------------------------------'
+ */
+[_ADJUST] =  LAYOUT(
+  KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,    _______, KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,
+  KC_F11,  KC_F12,  RGB_RMOD, RGB_SAI, RGB_SAD, _______, RGB_VAI, RGB_VAD, _______, _______, _______,
+  RESET,   RGB_TOG, RGB_MOD, RGB_HUI, RGB_HUD,  _______, KC_MPRV, KC_MNXT, KC_VOLD, KC_VOLU, KC_MPLY,
+                    _______, _______, _______,  _______, _______,  _______, _______
+)
+};
+
+bool process_record_user(uint16_t keycode, keyrecord_t *record) {
+  switch (keycode) {
+    case QWERTY:
+      if (record->event.pressed) {
+        // persistant_default_layer_set(1UL<<_QWERTY);
+        set_single_persistent_default_layer(_QWERTY);
+      }
+      return false;
+    case LOWER:
+      if (record->event.pressed) {
+        layer_on(_LOWER);
+        update_tri_layer(_LOWER, _RAISE, _ADJUST);
+      } else {
+        layer_off(_LOWER);
+        update_tri_layer(_LOWER, _RAISE, _ADJUST);
+      }
+      return false;
+    case RAISE:
+      if (record->event.pressed) {
+        layer_on(_RAISE);
+        update_tri_layer(_LOWER, _RAISE, _ADJUST);
+      } else {
+        layer_off(_RAISE);
+        update_tri_layer(_LOWER, _RAISE, _ADJUST);
+      }
+      return false;
+    case ADJUST:
+      if (record->event.pressed) {
+        layer_on(_ADJUST);
+      } else {
+        layer_off(_ADJUST);
+      }
+      return false;
+  }
+  return true;
+}
+
+void matrix_init_user(void) {
+
+}
+
+void matrix_scan_user(void) {
+
+}
+
+void led_set_user(uint8_t usb_led) {
+
+}

keyboards/halberd/keymaps/default/readme.md

@@ -0,0 +1 @@
+# The default keymap for halberd

keyboards/halberd/keymaps/right_modifiers/config.h

@@ -0,0 +1,19 @@
+/* Copyright 2019 ENDO Katsuhiro <ka2hiro@kagizaraya.jp>
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+
+// place overrides here

keyboards/halberd/keymaps/right_modifiers/keymap.c

@@ -0,0 +1,160 @@
+/* Copyright 2019 ENDO Katsuhiro <ka2hiro@kagizaraya.jp>
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include QMK_KEYBOARD_H
+
+// Defines the keycodes used by our macros in process_record_user
+enum layer_names {
+    _QWERTY,
+    _LOWER,
+    _RAISE,
+    _ADJUST,
+};
+
+// Defines the keycodes used by our macros in process_record_user
+enum custom_keycodes {
+  QWERTY = SAFE_RANGE,
+  LOWER,
+  RAISE,
+  ADJUST,
+};
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+/* Qwerty
+ *
+ * ,----------------------------------------------------------------------------.
+ * |   Q  |   W  |   E  |   R  |   T  |   Y  |   U  |   I  |   O  |   P  | BkSp |
+ * |------+------+------+------+------|------+------+------+------+------|------|
+ * |   A  |   S  |   D  |   F  |   G  |   H  |   J  |   K  |   L  |   ;  | Enter|
+ * |------+------+------+------+------|------+------+------+------+------|------|
+ * |   Z  |   X  |   C  |   V  |   B  |   N  |   M  |   ,  |   .  |   /  | Shift|
+ * `-------------+------+------+------|------+------+------+------+------+------'
+ *               | GUI  | LOWER|Ctrl/Esc|Space| RAISE| Alt | Tab  |
+ *               `------------------------------------------------'
+ */
+[_QWERTY] = LAYOUT(
+  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_BSPC,
+  KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN, KC_ENT,
+  KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH, KC_LSFT,
+                    KC_LGUI, LOWER, MT(MOD_LCTL, KC_ESC),  KC_SPC, RAISE, KC_LALT, KC_TAB
+),
+
+/* Raise
+ *
+ * ,----------------------------------------------------------------------------.
+ * |   !  |   @  |   #  |   $  |   %  |   ^  |   &  |   *  |   (  |   )  |      |
+ * |------+------+------+------+------|------+------+------+------+------|------|
+ * |  Tab |   _  |   +  |  |   |  ~   |   :  |   "  |   >  |   {  |   }  |      |
+ * |------+------+------+------+------|------+------+------+------+------|------|
+ * |  Caps|   -  |   =  |  \   |  `   |   ;  |   '  |   <  |   [  |   ]  |      |
+ * `-------------+------+------+------|------+------+------+------+------+------'
+ *               |      |      |      |      |      |      |      |
+ *               `------------------------------------------------'
+ */
+[_RAISE] = LAYOUT( 
+  KC_EXLM, KC_AT,   KC_HASH, KC_DLR,  KC_PERC, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, _______,
+  KC_TAB,  KC_UNDS, KC_PLUS, KC_PIPE, KC_TILD, KC_COLN, KC_DQUO, KC_GT,   KC_LCBR, KC_RCBR, _______,
+  KC_CAPS, KC_MINS, KC_EQL,  KC_BSLS, KC_GRV,  KC_SCLN, KC_QUOT, KC_LT,   KC_LBRC, KC_RBRC, _______,
+                    _______, _______, _______, _______, _______,  _______, _______
+),
+
+/* Lower
+ *
+ * ,----------------------------------------------------------------------------.
+ * |   1  |   2  |   3  |   4  |   5  |   6  |   7  |   8  |   9  |   0  |      |
+ * |------+------+------+------+------|------+------+------+------+------|------|
+ * |  Tab |      |      |      |Enter | Left | Down |  Up  | Right| Enter|      |
+ * |------+------+------+------+------|------+------+------+------+------|------|
+ * |  Ctrl|      |  GUI |  Alt | Del  | BkSp | PgUp | PgDn |      |      |      |
+ * `-------------+------+------+------|------+------+------+------+------+------'
+ *               |      |      |      |      |      |      |      |
+ *               `------------------------------------------------'
+ */
+[_LOWER] = LAYOUT(
+  KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    _______,
+  KC_TAB,  _______, _______, _______, KC_ENT,  KC_LEFT, KC_DOWN, KC_UP,   KC_RGHT, KC_ENT,  _______,
+  KC_LCTL, _______, KC_LGUI, KC_LALT, KC_DEL,  KC_BSPC, KC_PGUP, KC_PGDN, _______, _______, _______,
+                    _______, _______, _______, _______, _______, _______, _______
+),
+
+
+/* Adjust (Lower + Raise)
+ *
+ * ,----------------------------------------------------------------------------.
+ * |  F1  |  F2  |  F3  |  F4  |  F5  |   F6 |  F7  |  F8  |  F9  |  F10 |      |
+ * |------+------+------+------+------|------+------+------+------+------|------|
+ * |  F11 |  F12 |      |RGBSAI|RGBSAD|RGBVAI|RGBVAD|      |      |      |      |
+ * |------+------+------+------+------|------+------+------+------+------|------|
+ * | Reset|RGBTOG|RGBMOD|RGBHUI|RGBHUD| Prev | Next | Vol- | Vol+ | Play |      |
+ * `-------------+------+------+------|------+------+------+------+------+------'
+ *               |      |      |      |      |      |      |      |
+ *               `------------------------------------------------'
+ */
+[_ADJUST] =  LAYOUT(
+  KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,    KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  _______,
+  KC_F11,  KC_F12,  RGB_RMOD, RGB_SAI, RGB_SAD, RGB_VAI, RGB_VAD, _______, _______, _______, _______,
+  RESET,   RGB_TOG, RGB_MOD, RGB_HUI, RGB_HUD,  KC_MPRV, KC_MNXT, KC_VOLD, KC_VOLU, KC_MPLY, _______,
+                    _______, _______, _______,  _______, _______,  _______, _______
+)
+};
+
+bool process_record_user(uint16_t keycode, keyrecord_t *record) {
+  switch (keycode) {
+    case QWERTY:
+      if (record->event.pressed) {
+        // persistant_default_layer_set(1UL<<_QWERTY);
+        set_single_persistent_default_layer(_QWERTY);
+      }
+      return false;
+    case LOWER:
+      if (record->event.pressed) {
+        layer_on(_LOWER);
+        update_tri_layer(_LOWER, _RAISE, _ADJUST);
+      } else {
+        layer_off(_LOWER);
+        update_tri_layer(_LOWER, _RAISE, _ADJUST);
+      }
+      return false;
+    case RAISE:
+      if (record->event.pressed) {
+        layer_on(_RAISE);
+        update_tri_layer(_LOWER, _RAISE, _ADJUST);
+      } else {
+        layer_off(_RAISE);
+        update_tri_layer(_LOWER, _RAISE, _ADJUST);
+      }
+      return false;
+    case ADJUST:
+      if (record->event.pressed) {
+        layer_on(_ADJUST);
+      } else {
+        layer_off(_ADJUST);
+      }
+      return false;
+  }
+  return true;
+}
+
+void matrix_init_user(void) {
+
+}
+
+void matrix_scan_user(void) {
+
+}
+
+void led_set_user(uint8_t usb_led) {
+
+}

keyboards/halberd/keymaps/right_modifiers/readme.md

@@ -0,0 +1,2 @@
+# Modifiers on the right side.
+

keyboards/halberd/readme.md

@@ -0,0 +1,15 @@
+# Halberd
+
+![Halberd](https://i.imgur.com/QabQNPQ.jpg)
+
+40% keyboard.
+
+Keyboard Maintainer: [ka2hiro](https://github.com/ka2hiro) [@ka2hiro](https://twitter.com/ka2hiro)  
+Hardware Supported: Halberd PCB, ATMEGA32U4  
+Hardware Availability: [@kagizaraya](https://twitter.com/kagizaraya)
+
+Make example for this keyboard (after setting up your build environment):
+
+    make halberd:default:dfu
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/halberd/rules.mk

@@ -0,0 +1,80 @@
+# MCU name
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   atmega32a    bootloadHID
+BOOTLOADER = atmel-dfu
+
+
+# If you don't know the bootloader type, then you can specify the
+# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
+#   Teensy halfKay      512
+#   Teensy++ halfKay    1024
+#   Atmel DFU loader    4096
+#   LUFA bootloader     4096
+#   USBaspLoader        2048
+# OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE = lite     # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = no       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = no         # Console for debug(+400)
+COMMAND_ENABLE = no         # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE = no            # USB Nkey Rollover
+BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality on B7 by default
+RGBLIGHT_ENABLE = yes        # Enable keyboard RGB underglow
+MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no           # Audio output on port C6
+FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
+HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)

keyboards/handwired/frenchdev/matrix.c

@@ -5,11 +5,6 @@ The "column" and "row" in here actually refers to the opposite on the keyboard
 see definition of KEYMAP in v1.h, the grid is transposed so that a "row" in here is actually a "column" on the physical keyboard
 Nicolas
 
-Note for ErgoDox EZ customizers: Here be dragons!
-This is not a file you want to be messing with.
-All of the interesting stuff for you is under keymaps/ :)
-Love, Erez
-
 Copyright 2013 Oleg Kostyuk <cub.uanic@gmail.com>
 Copyright 2013 Nicolas Poirey <nicolas.poirey@gmail.com>
 

keyboards/keebio/iris/keymaps/pvinis/config.h

@@ -2,9 +2,9 @@
 
 
 #ifdef PRODUCT
-#undef PRODUCT
-#define PRODUCT Iris Keyboard - pvinis
-#endif // PRODUCT
+  #undef PRODUCT
+  #define PRODUCT Iris Keyboard - pvinis
+#endif
 
 
 // Use I2C or Serial, not both
@@ -20,5 +20,5 @@
 
 // choose pin to use for audio. c6 is the one iris uses.
 #ifdef AUDIO_ENABLE
-#define C6_AUDIO
-#endif // AUDIO_ENABLE
+  #define C6_AUDIO
+#endif

keyboards/keebio/iris/keymaps/pvinis/keymap.c

@@ -23,20 +23,18 @@
 #endif
 
 #ifdef AUDIO_ENABLE
-  //#define STARTUP_SONG SONG(SONIC_RING)
+  // #define STARTUP_SONG SONG(SONIC_RING)
 #endif
 
 #ifdef AUDIO_ENABLE
-float tone_sonic[][2] = SONG(IN_LIKE_FLINT);
-float tone_1[][2] = SONG(QWERTY_SOUND);
-float tone_2[][2] = SONG(OLD_SPICE);
-float tone_3[][2] = SONG(OVERWATCH_THEME);
-float tone_4[][2] = SONG(QWERTY_SOUND);
+  float tone_sonic[][2] = SONG(IN_LIKE_FLINT);
+  float tone_1[][2] = SONG(QWERTY_SOUND);
+  float tone_2[][2] = SONG(OLD_SPICE);
+  float tone_3[][2] = SONG(OVERWATCH_THEME);
+  float tone_4[][2] = SONG(QWERTY_SOUND);
 #endif
 
 
-
-
 const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
 
   // ,-----------------------------.              ,-----------------------------.

keyboards/keycapsss/o4l_5x12/config.h

@@ -0,0 +1,43 @@
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0x7983
+#define PRODUCT_ID      0x0512
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    Keycapsss
+#define PRODUCT         O4L:5x12
+#define DESCRIPTION     A 60 key ortholinear keyboard
+
+/* key matrix size */
+#define MATRIX_ROWS 5
+#define MATRIX_COLS 12
+
+/* key matrix pins */
+#define MATRIX_ROW_PINS { F7, B1, B3, B2, B6 }
+#define MATRIX_COL_PINS { B5, B4, E6, D7, C6, D4, D0, D1, D2, F6, F5, F4 }
+#define UNUSED_PINS
+
+/* COL2ROW or ROW2COL */
+#define DIODE_DIRECTION COL2ROW
+
+/* WS2812 RGB LED */
+#define RGB_DI_PIN D3
+
+#ifdef RGB_DI_PIN
+#define RGBLIGHT_ANIMATIONS
+#define RGBLED_NUM 12    // Number of LEDs
+#define RGBLIGHT_HUE_STEP 4
+#define RGBLIGHT_SAT_STEP 4
+#define RGBLIGHT_VAL_STEP 4
+#endif
+
+/* Set 0 if debouncing isn't needed */
+#define DEBOUNCING_DELAY 5
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE

keyboards/keycapsss/o4l_5x12/keymaps/2x2u/config.h

@@ -0,0 +1,3 @@
+#pragma once
+
+// place overrides here

keyboards/keycapsss/o4l_5x12/keymaps/2x2u/keymap.c

@@ -0,0 +1,83 @@
+#include QMK_KEYBOARD_H
+
+// Each layer gets a name for readability, which is then used in the keymap matrix below.
+// The underscores don't mean anything - you can have a layer called STUFF or any other name.
+// Layer names don't all need to be of the same length, obviously, and you can also skip them
+// entirely and just use numbers.
+enum o4l5x12_layers {
+  _QWERTY,
+  _LOWER
+};
+
+// Layers get their own keys. These are defined to make them not mess up
+// the grid.
+enum o4l5x12_keycodes {
+  QWERTY = SAFE_RANGE,
+  LOWER
+};
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+/* Qwerty
+ * ,-----------------------------------------------------------------------------------.
+ * |   1  |   2  |   3  |   4  |   5  |   6  |   7  |   8  |   9  |   0  |   -  |   =  |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * | ESC  |   Q  |   W  |   E  |   R  |   T  |   Y  |   U  |   I  |   O  |   P  | BSPC |
+ * |------+------+------+------+------+-------------+------+------+------+------+------|
+ * | Tab  |   A  |   S  |   D  |   F  |   G  |   H  |   J  |   K  |   L  |   ;  |  "   |
+ * |------+------+------+------+------+------|------+------+------+------+------+------|
+ * | Shift|   Z  |   X  |   C  |   V  |   B  |   N  |   M  |   ,  |   .  |   /  |Enter |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * | Ctrl | Alt  | GUI  |Lower |    Enter    |    Space    | Left | Down |  Up  |Right |
+ * `-----------------------------------------------------------------------------------'
+ */
+[_QWERTY] = LAYOUT_ortho_5x12_2x2u(
+  KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    KC_MINS, KC_EQL,
+  KC_GESC, KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_BSPC,
+  KC_TAB,  KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN, KC_QUOT,
+  KC_LSFT, KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH, KC_ENT,
+  KC_LCTL, KC_LALT, KC_LGUI, LOWER,      KC_ENT,           KC_SPC,        KC_LEFT, KC_DOWN, KC_UP,   KC_RGHT
+),
+
+/* Lower
+ * ,-----------------------------------------------------------------------------------.
+ * |  F1  |  F2  |  F3  |  F4  |  F5  |  F6  |  F7  |  F8  |  F9  |  F10 |  F11 |  F12 |
+ * |------+------+------+------+------+-------------+------+------+------+------+------|
+ * |   1  |   2  |   3  |   4  |   5  |   6  |   7  |   8  |   9  |   0  |      | Del  |
+ * |------+------+------+------+------+-------------+------+------+------+------+------|
+ * |RGBPLA|   {  |   [  |   (  |      |      |   )  |   ]  |   }  |      |      |  |   |
+ * |------+------+------+------+------+------|------+------+------+------+------+------|
+ * |RGBMOD|      |      |      |      |      |      |      |      |      |      |      |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * |UGlow | Reset|      |      |             |             | Next | Vol- | Vol+ | Play |
+ * `-----------------------------------------------------------------------------------'
+ */
+[_LOWER] = LAYOUT_ortho_5x12_2x2u(
+  KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,
+  KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    _______, KC_DEL,
+  RGB_M_P, KC_LCBR, KC_LBRC, KC_LPRN, KC_SLSH, KC_BSLS, KC_RPRN, KC_RBRC, KC_RCBR, _______, _______, KC_PIPE,
+  RGB_MOD, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,
+  RGB_TOG, RESET,   _______, _______,     _______,          _______,      KC_MNXT, KC_VOLD, KC_VOLU, KC_MPLY
+),
+
+};
+
+bool process_record_user(uint16_t keycode, keyrecord_t *record) {
+  switch (keycode) {
+        case QWERTY:
+          if (record->event.pressed) {
+            set_single_persistent_default_layer(_QWERTY);
+          }
+          return false;
+          break;
+        case LOWER:
+          if (record->event.pressed) {
+            layer_on(_LOWER);
+          } else {
+            layer_off(_LOWER);
+          }
+          return false;
+          break;
+      }
+    return true;
+};

keyboards/keycapsss/o4l_5x12/keymaps/default/config.h

@@ -0,0 +1,3 @@
+#pragma once
+
+// place overrides here

keyboards/keycapsss/o4l_5x12/keymaps/default/keymap.c

@@ -0,0 +1,140 @@
+#include QMK_KEYBOARD_H
+
+// Each layer gets a name for readability, which is then used in the keymap matrix below.
+// The underscores don't mean anything - you can have a layer called STUFF or any other name.
+// Layer names don't all need to be of the same length, obviously, and you can also skip them
+// entirely and just use numbers.
+enum preonic_layers {
+  _QWERTY,
+  _LOWER,
+  _RAISE,
+  _ADJUST
+};
+
+// Layers get their own keys. These are defined to make them not mess up
+// the grid.
+enum preonic_keycodes {
+  QWERTY = SAFE_RANGE,
+  LOWER,
+  RAISE
+};
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+/* Qwerty (Preonic Layer Style)
+ * ,-----------------------------------------------------------------------------------.
+ * |   `  |   1  |   2  |   3  |   4  |   5  |   6  |   7  |   8  |   9  |   0  | Bksp |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * | Tab  |   Q  |   W  |   E  |   R  |   T  |   Y  |   U  |   I  |   O  |   P  | Del  |
+ * |------+------+------+------+------+-------------+------+------+------+------+------|
+ * | Esc  |   A  |   S  |   D  |   F  |   G  |   H  |   J  |   K  |   L  |   ;  |  "   |
+ * |------+------+------+------+------+------|------+------+------+------+------+------|
+ * | Shift|   Z  |   X  |   C  |   V  |   B  |   N  |   M  |   ,  |   .  |   /  |Enter |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * |      | Ctrl | Alt  | GUI  |Lower |Space |Space |Raise | Left | Down |  Up  |Right |
+ * `-----------------------------------------------------------------------------------'
+ */
+[_QWERTY] = LAYOUT_ortho_5x12(
+  KC_GRV,  KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    KC_BSPC,
+  KC_TAB,  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_DEL,
+  KC_ESC,  KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN, KC_QUOT,
+  KC_LSFT, KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH, KC_ENT,
+  RGB_TOG, KC_LCTL, KC_LALT, KC_LGUI, LOWER,   KC_SPC,  KC_SPC,  RAISE,   KC_LEFT, KC_DOWN, KC_UP,   KC_RGHT
+),
+
+/* Lower (Preonic Layer Style)
+ * ,-----------------------------------------------------------------------------------.
+ * |   ~  |   !  |   @  |   #  |   $  |   %  |   ^  |   &  |   *  |   (  |   )  | Bksp |
+ * |------+------+------+------+------+-------------+------+------+------+------+------|
+ * |   ~  |   !  |   @  |   #  |   $  |   %  |   ^  |   &  |   *  |   (  |   )  | Del  |
+ * |------+------+------+------+------+-------------+------+------+------+------+------|
+ * | Del  |  F1  |  F2  |  F3  |  F4  |  F5  |  F6  |   _  |   +  |   {  |   }  |  |   |
+ * |------+------+------+------+------+------|------+------+------+------+------+------|
+ * |      |  F7  |  F8  |  F9  |  F10 |  F11 |  F12 |ISO ~ |ISO | |      |      |      |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * |      |      |      |      |      |      |      |      | Next | Vol- | Vol+ | Play |
+ * `-----------------------------------------------------------------------------------'
+ */
+[_LOWER] = LAYOUT_ortho_5x12(
+  KC_TILD, KC_EXLM, KC_AT,   KC_HASH, KC_DLR,  KC_PERC, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, KC_BSPC,
+  KC_TILD, KC_EXLM, KC_AT,   KC_HASH, KC_DLR,  KC_PERC, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, KC_DEL,
+  KC_DEL,  KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_UNDS, KC_PLUS, KC_LCBR, KC_RCBR, KC_PIPE,
+  _______, KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,S(KC_NUHS),S(KC_NUBS),KC_HOME, KC_END, _______,
+  _______, _______, _______, _______, _______, _______, _______, _______, KC_MNXT, KC_VOLD, KC_VOLU, KC_MPLY
+),
+
+/* Raise (Preonic Layer Style)
+ * ,-----------------------------------------------------------------------------------.
+ * |   `  |   1  |   2  |   3  |   4  |   5  |   6  |   7  |   8  |   9  |   0  | Bksp |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * |   `  |   1  |   2  |   3  |   4  |   5  |   6  |   7  |   8  |   9  |   0  | Del  |
+ * |------+------+------+------+------+-------------+------+------+------+------+------|
+ * | Del  |  F1  |  F2  |  F3  |  F4  |  F5  |  F6  |   -  |   =  |   [  |   ]  |  \   |
+ * |------+------+------+------+------+------|------+------+------+------+------+------|
+ * |      |  F7  |  F8  |  F9  |  F10 |  F11 |  F12 |ISO # |ISO / |      |      |      |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * |      |      |      |      |      |      |      |      | Next | Vol- | Vol+ | Play |
+ * `-----------------------------------------------------------------------------------'
+ */
+[_RAISE] = LAYOUT_ortho_5x12(
+  KC_GRV,  KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    KC_BSPC,
+  KC_GRV,  KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    KC_DEL,
+  KC_DEL,  KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_MINS, KC_EQL,  KC_LBRC, KC_RBRC, KC_BSLS,
+  _______, KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,  KC_NUHS, KC_NUBS, KC_PGUP, KC_PGDN, _______,
+  _______, _______, _______, _______, _______, _______, _______, _______, KC_MNXT, KC_VOLD, KC_VOLU, KC_MPLY
+),
+
+/* Adjust (Lower + Raise) (Preonic Layer Style)
+ * ,-----------------------------------------------------------------------------------.
+ * |  F1  |  F2  |  F3  |  F4  |  F5  |  F6  |  F7  |  F8  |  F9  |  F10 |  F11 |  F12 |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * |      | Reset|      |      |      |      |      |      |      |      |      |  Del |
+ * |------+------+------+------+------+-------------+------+------+------+------+------|
+ * |      |      |      |Aud on|AudOff|AGnorm|AGswap|Qwerty|      |      |      |      |
+ * |------+------+------+------+------+------|------+------+------+------+------+------|
+ * |      |Voice-|Voice+|Mus on|MusOff|MidiOn|MidOff|      |      |      |      |      |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * |      |      |      |      |      |      |      |      |      |      |      |      |
+ * `-----------------------------------------------------------------------------------'
+ */
+[_ADJUST] = LAYOUT_ortho_5x12(
+  KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,
+  _______, RESET,   DEBUG,   _______, _______, _______, _______, TERM_ON, TERM_OFF,_______, _______, KC_DEL,
+  _______, _______, MU_MOD,  AU_ON,   AU_OFF,  AG_NORM, AG_SWAP, QWERTY,  _______, _______, _______, _______,
+  _______, MUV_DE,  MUV_IN,  MU_ON,   MU_OFF,  MI_ON,   MI_OFF,  _______, _______, _______, _______, _______,
+  _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______
+)
+
+};
+
+bool process_record_user(uint16_t keycode, keyrecord_t *record) {
+  switch (keycode) {
+        case QWERTY:
+          if (record->event.pressed) {
+            set_single_persistent_default_layer(_QWERTY);
+          }
+          return false;
+          break;
+        case LOWER:
+          if (record->event.pressed) {
+            layer_on(_LOWER);
+            update_tri_layer(_LOWER, _RAISE, _ADJUST);
+          } else {
+            layer_off(_LOWER);
+            update_tri_layer(_LOWER, _RAISE, _ADJUST);
+          }
+          return false;
+          break;
+        case RAISE:
+          if (record->event.pressed) {
+            layer_on(_RAISE);
+            update_tri_layer(_LOWER, _RAISE, _ADJUST);
+          } else {
+            layer_off(_RAISE);
+            update_tri_layer(_LOWER, _RAISE, _ADJUST);
+          }
+          return false;
+          break;
+      }
+    return true;
+};

keyboards/keycapsss/o4l_5x12/o4l_5x12.c

@@ -0,0 +1 @@
+#include "o4l_5x12.h"

keyboards/keycapsss/o4l_5x12/o4l_5x12.h

@@ -0,0 +1,50 @@
+#pragma once
+
+#include "quantum.h"
+
+#define XXX KC_NO
+
+  #define LAYOUT_ortho_5x12( \
+	  k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b, \
+	  k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b, \
+	  k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b, \
+	  k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3a, k3b, \
+	  k40, k41, k42, k43, k44, k45, k46, k47, k48, k49, k4a, k4b \
+  ) \
+  { \
+	  { k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b }, \
+	  { k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b, }, \
+	  { k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b }, \
+	  { k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3a, k3b, }, \
+	  { k40, k41, k42, k43, k44, k45, k46, k47, k48, k49, k4a, k4b } \
+  }
+
+  #define LAYOUT_ortho_5x12_1x2uC( \
+	  k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b, \
+	  k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b, \
+	  k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b, \
+	  k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3a, k3b, \
+	  k40, k41, k42, k43, k44,   k45,    k47, k48, k49, k4a, k4b \
+  ) \
+  { \
+	  { k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b }, \
+	  { k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b, }, \
+	  { k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b }, \
+	  { k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3a, k3b, }, \
+	  { k40, k41, k42, k43, k44, k45, XXX, k47, k48, k49, k4a, k4b } \
+  }
+
+    #define LAYOUT_ortho_5x12_2x2u( \
+	  k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b, \
+	  k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b, \
+	  k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b, \
+	  k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3a, k3b, \
+	  k40, k41, k42, k43,    k44,     k46,    k48, k49, k4a, k4b \
+  ) \
+  { \
+	  { k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b }, \
+	  { k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b, }, \
+	  { k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b }, \
+	  { k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3a, k3b, }, \
+	  { k40, k41, k42, k43, k44, XXX, k46, XXX, k48, k49, k4a, k4b } \
+  }

keyboards/keycapsss/o4l_5x12/readme.md

@@ -0,0 +1,31 @@
+# O4L 5x12
+
+A ortholinear 5x12 keyboard made and sold by Keycapsss. [More info at Keycapsss.com](https://keycapsss.com).
+
+<img src="https://i.imgur.com/5p8rDme.jpg" height="500px">
+
+## Features:
+
+- MX and Choc switch support
+- RGB Underglow (12x SK6812MINI)
+- USB-C
+- PCB shape, reset button and mounting holes position same as Preonic Rev3
+- Pro Micro as controller
+
+---
+
+- Keyboard Maintainer: BenRoe [Github](https://github.com/BenRoe) / [Twitter](https://twitter.com/ben_roe)  
+- Hardware Supported: Pro Micro  
+- Hardware Availability: [Keycapsss.com](https://keycapsss.com)  
+
+
+
+Make firmware .hex for this keyboard (after setting up your build environment):
+
+    make keycapsss/o4l_5x12:default
+
+Example of flashing this keyboard (or use [QMK Toolbox](https://github.com/qmk/qmk_toolbox)):
+
+    make keycapsss/o4l_5x12:default:avrdude
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/keycapsss/o4l_5x12/rules.mk

@@ -0,0 +1,73 @@
+# MCU name
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   atmega32a    bootloadHID
+BOOTLOADER = caterina
+
+
+# If you don't know the bootloader type, then you can specify the
+# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
+#   Teensy halfKay      512
+#   Teensy++ halfKay    1024
+#   Atmel DFU loader    4096
+#   LUFA bootloader     4096
+#   USBaspLoader        2048
+# OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+BOOTMAGIC_ENABLE = no       # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = no        # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = no         # Console for debug(+400)
+COMMAND_ENABLE = yes        # Commands for debug and configuration
+NKRO_ENABLE = no            # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+BACKLIGHT_ENABLE = no      # Enable keyboard backlight functionality
+MIDI_ENABLE = no            # MIDI controls
+AUDIO_ENABLE = no           # Audio output on port C6
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+RGBLIGHT_ENABLE = yes       # Enable WS2812 RGB underlight.
+
+LAYOUTS = ortho_5x12

keyboards/lets_split/keymaps/DE_simple/readme.md

@@ -21,15 +21,15 @@ Layout
     `-----------------------------------------------------------------------------------'
     
     
-    Qwerty
+    Lower
     ,-----------------------------------------------------------------------------------.
-    | Esc  |   Q  |   W  |   E  |   R  |   T  |   Z  |   U  |   I  |   O  |   P  | Bksp |
+    |   °  |   !  |   "  |   §  |   $  |   %  |   &  |   /  |   (  |   )  |   =  | Bksp |
     |------+------+------+------+------+-------------+------+------+------+------+------|
-    | Tab  |   A  |   S  |   D  |   F  |   G  |   H  |   J  |   K  |   L  |   +  |  #   |
+    | Del  |  F1  |  F2  |  F3  |  F4  |  F5  |  F6  |   @  |   €  |   ü  |   ?  |  ´   |
     |------+------+------+------+------+------|------+------+------+------+------+------|
-    | Shift|   Y  |   X  |   C  |   V  |   B  |   N  |   M  |   ,  |   .  |   -  |Enter |
+    | Shift|  F7  |  F8  |  F9  |  F10 |  F11 |  F12 |   |  |   ö  |   ä  |      |Enter |
     |------+------+------+------+------+------+------+------+------+------+------+------|
-    | Ctrl | Alt  | AltGr| GUI  |Lower |Space |Space |Raise | Left | Down |  Up  |Right |
+    |      |      |      |      |      |             |      | Next | Vol- | Vol+ | Play |
     `-----------------------------------------------------------------------------------'
     
     

keyboards/lily58/ssd1306.c

@@ -13,7 +13,7 @@
 #include "sendchar.h"
 #include "timer.h"
 
-static const unsigned char font[] PROGMEM;
+extern const unsigned char font[] PROGMEM;
 
 // Set this to 1 to help diagnose early startup problems
 // when testing power-on with ble.  Turn it off otherwise,

keyboards/nk65/boards/GENERIC_STM32_F303XC/board.c

@@ -0,0 +1,126 @@
+/*
+    ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio
+
+    Licensed under the Apache License, Version 2.0 (the "License");
+    you may not use this file except in compliance with the License.
+    You may obtain a copy of the License at
+
+        http://www.apache.org/licenses/LICENSE-2.0
+
+    Unless required by applicable law or agreed to in writing, software
+    distributed under the License is distributed on an "AS IS" BASIS,
+    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+    See the License for the specific language governing permissions and
+    limitations under the License.
+*/
+
+#include "hal.h"
+
+#if HAL_USE_PAL || defined(__DOXYGEN__)
+/**
+ * @brief   PAL setup.
+ * @details Digital I/O ports static configuration as defined in @p board.h.
+ *          This variable is used by the HAL when initializing the PAL driver.
+ */
+const PALConfig pal_default_config = {
+#if STM32_HAS_GPIOA
+  {VAL_GPIOA_MODER, VAL_GPIOA_OTYPER, VAL_GPIOA_OSPEEDR, VAL_GPIOA_PUPDR,
+   VAL_GPIOA_ODR,   VAL_GPIOA_AFRL,   VAL_GPIOA_AFRH},
+#endif
+#if STM32_HAS_GPIOB
+  {VAL_GPIOB_MODER, VAL_GPIOB_OTYPER, VAL_GPIOB_OSPEEDR, VAL_GPIOB_PUPDR,
+   VAL_GPIOB_ODR,   VAL_GPIOB_AFRL,   VAL_GPIOB_AFRH},
+#endif
+#if STM32_HAS_GPIOC
+  {VAL_GPIOC_MODER, VAL_GPIOC_OTYPER, VAL_GPIOC_OSPEEDR, VAL_GPIOC_PUPDR,
+   VAL_GPIOC_ODR,   VAL_GPIOC_AFRL,   VAL_GPIOC_AFRH},
+#endif
+#if STM32_HAS_GPIOD
+  {VAL_GPIOD_MODER, VAL_GPIOD_OTYPER, VAL_GPIOD_OSPEEDR, VAL_GPIOD_PUPDR,
+   VAL_GPIOD_ODR,   VAL_GPIOD_AFRL,   VAL_GPIOD_AFRH},
+#endif
+#if STM32_HAS_GPIOE
+  {VAL_GPIOE_MODER, VAL_GPIOE_OTYPER, VAL_GPIOE_OSPEEDR, VAL_GPIOE_PUPDR,
+   VAL_GPIOE_ODR,   VAL_GPIOE_AFRL,   VAL_GPIOE_AFRH},
+#endif
+#if STM32_HAS_GPIOF
+  {VAL_GPIOF_MODER, VAL_GPIOF_OTYPER, VAL_GPIOF_OSPEEDR, VAL_GPIOF_PUPDR,
+   VAL_GPIOF_ODR,   VAL_GPIOF_AFRL,   VAL_GPIOF_AFRH},
+#endif
+#if STM32_HAS_GPIOG
+  {VAL_GPIOG_MODER, VAL_GPIOG_OTYPER, VAL_GPIOG_OSPEEDR, VAL_GPIOG_PUPDR,
+   VAL_GPIOG_ODR,   VAL_GPIOG_AFRL,   VAL_GPIOG_AFRH},
+#endif
+#if STM32_HAS_GPIOH
+  {VAL_GPIOH_MODER, VAL_GPIOH_OTYPER, VAL_GPIOH_OSPEEDR, VAL_GPIOH_PUPDR,
+   VAL_GPIOH_ODR,   VAL_GPIOH_AFRL,   VAL_GPIOH_AFRH},
+#endif
+#if STM32_HAS_GPIOI
+  {VAL_GPIOI_MODER, VAL_GPIOI_OTYPER, VAL_GPIOI_OSPEEDR, VAL_GPIOI_PUPDR,
+   VAL_GPIOI_ODR,   VAL_GPIOI_AFRL,   VAL_GPIOI_AFRH}
+#endif
+};
+#endif
+
+void enter_bootloader_mode_if_requested(void);
+
+/**
+ * @brief   Early initialization code.
+ * @details This initialization must be performed just after stack setup
+ *          and before any other initialization.
+ */
+void __early_init(void) {
+  enter_bootloader_mode_if_requested();
+  stm32_clock_init();
+}
+
+#if HAL_USE_SDC || defined(__DOXYGEN__)
+/**
+ * @brief   SDC card detection.
+ */
+bool sdc_lld_is_card_inserted(SDCDriver *sdcp) {
+
+  (void)sdcp;
+  /* TODO: Fill the implementation.*/
+  return true;
+}
+
+/**
+ * @brief   SDC card write protection detection.
+ */
+bool sdc_lld_is_write_protected(SDCDriver *sdcp) {
+
+  (void)sdcp;
+  /* TODO: Fill the implementation.*/
+  return false;
+}
+#endif /* HAL_USE_SDC */
+
+#if HAL_USE_MMC_SPI || defined(__DOXYGEN__)
+/**
+ * @brief   MMC_SPI card detection.
+ */
+bool mmc_lld_is_card_inserted(MMCDriver *mmcp) {
+
+  (void)mmcp;
+  /* TODO: Fill the implementation.*/
+  return true;
+}
+
+/**
+ * @brief   MMC_SPI card write protection detection.
+ */
+bool mmc_lld_is_write_protected(MMCDriver *mmcp) {
+
+  (void)mmcp;
+  /* TODO: Fill the implementation.*/
+  return false;
+}
+#endif
+
+/**
+ * @brief   Board-specific initialization code.
+ * @todo    Add your board-specific code, if any.
+ */
+void boardInit(void) {
+}

keyboards/nk65/boards/GENERIC_STM32_F303XC/board.mk

@@ -0,0 +1,5 @@
+# List of all the board related files.
+BOARDSRC = $(BOARD_PATH)/boards/GENERIC_STM32_F303XC/board.c
+
+# Required include directories
+BOARDINC = $(BOARD_PATH)/boards/GENERIC_STM32_F303XC

keyboards/nk65/bootloader_defs.h

@@ -0,0 +1,7 @@
+/* Address for jumping to bootloader on STM32 chips. */
+/* It is chip dependent, the correct number can be looked up here:
+ * http://www.st.com/web/en/resource/technical/document/application_note/CD00167594.pdf
+ * This also requires a patch to chibios:
+ *  <tmk_dir>/tmk_core/tool/chibios/ch-bootloader-jump.patch
+ */
+#define STM32_BOOTLOADER_ADDRESS 0x1FFFD800

keyboards/nk65/chconf.h

@@ -0,0 +1,520 @@
+/*
+    ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio
+
+    Licensed under the Apache License, Version 2.0 (the "License");
+    you may not use this file except in compliance with the License.
+    You may obtain a copy of the License at
+
+        http://www.apache.org/licenses/LICENSE-2.0
+
+    Unless required by applicable law or agreed to in writing, software
+    distributed under the License is distributed on an "AS IS" BASIS,
+    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+    See the License for the specific language governing permissions and
+    limitations under the License.
+*/
+
+/**
+ * @file    templates/chconf.h
+ * @brief   Configuration file template.
+ * @details A copy of this file must be placed in each project directory, it
+ *          contains the application specific kernel settings.
+ *
+ * @addtogroup config
+ * @details Kernel related settings and hooks.
+ * @{
+ */
+
+#ifndef CHCONF_H
+#define CHCONF_H
+
+#define _CHIBIOS_RT_CONF_
+
+/*===========================================================================*/
+/**
+ * @name System timers settings
+ * @{
+ */
+/*===========================================================================*/
+
+/**
+ * @brief   System time counter resolution.
+ * @note    Allowed values are 16 or 32 bits.
+ */
+#define CH_CFG_ST_RESOLUTION                32
+
+/**
+ * @brief   System tick frequency.
+ * @details Frequency of the system timer that drives the system ticks. This
+ *          setting also defines the system tick time unit.
+ */
+#define CH_CFG_ST_FREQUENCY                 100000
+
+/**
+ * @brief   Time delta constant for the tick-less mode.
+ * @note    If this value is zero then the system uses the classic
+ *          periodic tick. This value represents the minimum number
+ *          of ticks that is safe to specify in a timeout directive.
+ *          The value one is not valid, timeouts are rounded up to
+ *          this value.
+ */
+#define CH_CFG_ST_TIMEDELTA                 2
+
+/** @} */
+
+/*===========================================================================*/
+/**
+ * @name Kernel parameters and options
+ * @{
+ */
+/*===========================================================================*/
+
+/**
+ * @brief   Round robin interval.
+ * @details This constant is the number of system ticks allowed for the
+ *          threads before preemption occurs. Setting this value to zero
+ *          disables the preemption for threads with equal priority and the
+ *          round robin becomes cooperative. Note that higher priority
+ *          threads can still preempt, the kernel is always preemptive.
+ * @note    Disabling the round robin preemption makes the kernel more compact
+ *          and generally faster.
+ * @note    The round robin preemption is not supported in tickless mode and
+ *          must be set to zero in that case.
+ */
+#define CH_CFG_TIME_QUANTUM                 0
+
+/**
+ * @brief   Managed RAM size.
+ * @details Size of the RAM area to be managed by the OS. If set to zero
+ *          then the whole available RAM is used. The core memory is made
+ *          available to the heap allocator and/or can be used directly through
+ *          the simplified core memory allocator.
+ *
+ * @note    In order to let the OS manage the whole RAM the linker script must
+ *          provide the @p __heap_base__ and @p __heap_end__ symbols.
+ * @note    Requires @p CH_CFG_USE_MEMCORE.
+ */
+#define CH_CFG_MEMCORE_SIZE                 0
+
+/**
+ * @brief   Idle thread automatic spawn suppression.
+ * @details When this option is activated the function @p chSysInit()
+ *          does not spawn the idle thread. The application @p main()
+ *          function becomes the idle thread and must implement an
+ *          infinite loop.
+ */
+#define CH_CFG_NO_IDLE_THREAD               FALSE
+
+/** @} */
+
+/*===========================================================================*/
+/**
+ * @name Performance options
+ * @{
+ */
+/*===========================================================================*/
+
+/**
+ * @brief   OS optimization.
+ * @details If enabled then time efficient rather than space efficient code
+ *          is used when two possible implementations exist.
+ *
+ * @note    This is not related to the compiler optimization options.
+ * @note    The default is @p TRUE.
+ */
+#define CH_CFG_OPTIMIZE_SPEED               TRUE
+
+/** @} */
+
+/*===========================================================================*/
+/**
+ * @name Subsystem options
+ * @{
+ */
+/*===========================================================================*/
+
+/**
+ * @brief   Time Measurement APIs.
+ * @details If enabled then the time measurement APIs are included in
+ *          the kernel.
+ *
+ * @note    The default is @p TRUE.
+ */
+#define CH_CFG_USE_TM                       TRUE
+
+/**
+ * @brief   Threads registry APIs.
+ * @details If enabled then the registry APIs are included in the kernel.
+ *
+ * @note    The default is @p TRUE.
+ */
+#define CH_CFG_USE_REGISTRY                 TRUE
+
+/**
+ * @brief   Threads synchronization APIs.
+ * @details If enabled then the @p chThdWait() function is included in
+ *          the kernel.
+ *
+ * @note    The default is @p TRUE.
+ */
+#define CH_CFG_USE_WAITEXIT                 TRUE
+
+/**
+ * @brief   Semaphores APIs.
+ * @details If enabled then the Semaphores APIs are included in the kernel.
+ *
+ * @note    The default is @p TRUE.
+ */
+#define CH_CFG_USE_SEMAPHORES               TRUE
+
+/**
+ * @brief   Semaphores queuing mode.
+ * @details If enabled then the threads are enqueued on semaphores by
+ *          priority rather than in FIFO order.
+ *
+ * @note    The default is @p FALSE. Enable this if you have special
+ *          requirements.
+ * @note    Requires @p CH_CFG_USE_SEMAPHORES.
+ */
+#define CH_CFG_USE_SEMAPHORES_PRIORITY      FALSE
+
+/**
+ * @brief   Mutexes APIs.
+ * @details If enabled then the mutexes APIs are included in the kernel.
+ *
+ * @note    The default is @p TRUE.
+ */
+#define CH_CFG_USE_MUTEXES                  TRUE
+
+/**
+ * @brief   Enables recursive behavior on mutexes.
+ * @note    Recursive mutexes are heavier and have an increased
+ *          memory footprint.
+ *
+ * @note    The default is @p FALSE.
+ * @note    Requires @p CH_CFG_USE_MUTEXES.
+ */
+#define CH_CFG_USE_MUTEXES_RECURSIVE        FALSE
+
+/**
+ * @brief   Conditional Variables APIs.
+ * @details If enabled then the conditional variables APIs are included
+ *          in the kernel.
+ *
+ * @note    The default is @p TRUE.
+ * @note    Requires @p CH_CFG_USE_MUTEXES.
+ */
+#define CH_CFG_USE_CONDVARS                 TRUE
+
+/**
+ * @brief   Conditional Variables APIs with timeout.
+ * @details If enabled then the conditional variables APIs with timeout
+ *          specification are included in the kernel.
+ *
+ * @note    The default is @p TRUE.
+ * @note    Requires @p CH_CFG_USE_CONDVARS.
+ */
+#define CH_CFG_USE_CONDVARS_TIMEOUT         TRUE
+
+/**
+ * @brief   Events Flags APIs.
+ * @details If enabled then the event flags APIs are included in the kernel.
+ *
+ * @note    The default is @p TRUE.
+ */
+#define CH_CFG_USE_EVENTS                   TRUE
+
+/**
+ * @brief   Events Flags APIs with timeout.
+ * @details If enabled then the events APIs with timeout specification
+ *          are included in the kernel.
+ *
+ * @note    The default is @p TRUE.
+ * @note    Requires @p CH_CFG_USE_EVENTS.
+ */
+#define CH_CFG_USE_EVENTS_TIMEOUT           TRUE
+
+/**
+ * @brief   Synchronous Messages APIs.
+ * @details If enabled then the synchronous messages APIs are included
+ *          in the kernel.
+ *
+ * @note    The default is @p TRUE.
+ */
+#define CH_CFG_USE_MESSAGES                 TRUE
+
+/**
+ * @brief   Synchronous Messages queuing mode.
+ * @details If enabled then messages are served by priority rather than in
+ *          FIFO order.
+ *
+ * @note    The default is @p FALSE. Enable this if you have special
+ *          requirements.
+ * @note    Requires @p CH_CFG_USE_MESSAGES.
+ */
+#define CH_CFG_USE_MESSAGES_PRIORITY        TRUE
+
+/**
+ * @brief   Mailboxes APIs.
+ * @details If enabled then the asynchronous messages (mailboxes) APIs are
+ *          included in the kernel.
+ *
+ * @note    The default is @p TRUE.
+ * @note    Requires @p CH_CFG_USE_SEMAPHORES.
+ */
+#define CH_CFG_USE_MAILBOXES                TRUE
+
+/**
+ * @brief   Core Memory Manager APIs.
+ * @details If enabled then the core memory manager APIs are included
+ *          in the kernel.
+ *
+ * @note    The default is @p TRUE.
+ */
+#define CH_CFG_USE_MEMCORE                  TRUE
+
+/**
+ * @brief   Heap Allocator APIs.
+ * @details If enabled then the memory heap allocator APIs are included
+ *          in the kernel.
+ *
+ * @note    The default is @p TRUE.
+ * @note    Requires @p CH_CFG_USE_MEMCORE and either @p CH_CFG_USE_MUTEXES or
+ *          @p CH_CFG_USE_SEMAPHORES.
+ * @note    Mutexes are recommended.
+ */
+#define CH_CFG_USE_HEAP                     TRUE
+
+/**
+ * @brief   Memory Pools Allocator APIs.
+ * @details If enabled then the memory pools allocator APIs are included
+ *          in the kernel.
+ *
+ * @note    The default is @p TRUE.
+ */
+#define CH_CFG_USE_MEMPOOLS                 TRUE
+
+/**
+ * @brief   Dynamic Threads APIs.
+ * @details If enabled then the dynamic threads creation APIs are included
+ *          in the kernel.
+ *
+ * @note    The default is @p TRUE.
+ * @note    Requires @p CH_CFG_USE_WAITEXIT.
+ * @note    Requires @p CH_CFG_USE_HEAP and/or @p CH_CFG_USE_MEMPOOLS.
+ */
+#define CH_CFG_USE_DYNAMIC                  TRUE
+
+/** @} */
+
+/*===========================================================================*/
+/**
+ * @name Debug options
+ * @{
+ */
+/*===========================================================================*/
+
+/**
+ * @brief   Debug option, kernel statistics.
+ *
+ * @note    The default is @p FALSE.
+ */
+#define CH_DBG_STATISTICS                   FALSE
+
+/**
+ * @brief   Debug option, system state check.
+ * @details If enabled the correct call protocol for system APIs is checked
+ *          at runtime.
+ *
+ * @note    The default is @p FALSE.
+ */
+#define CH_DBG_SYSTEM_STATE_CHECK           FALSE
+
+/**
+ * @brief   Debug option, parameters checks.
+ * @details If enabled then the checks on the API functions input
+ *          parameters are activated.
+ *
+ * @note    The default is @p FALSE.
+ */
+#define CH_DBG_ENABLE_CHECKS                FALSE
+
+/**
+ * @brief   Debug option, consistency checks.
+ * @details If enabled then all the assertions in the kernel code are
+ *          activated. This includes consistency checks inside the kernel,
+ *          runtime anomalies and port-defined checks.
+ *
+ * @note    The default is @p FALSE.
+ */
+#define CH_DBG_ENABLE_ASSERTS               FALSE
+
+/**
+ * @brief   Debug option, trace buffer.
+ * @details If enabled then the trace buffer is activated.
+ *
+ * @note    The default is @p CH_DBG_TRACE_MASK_DISABLED.
+ */
+#define CH_DBG_TRACE_MASK                   CH_DBG_TRACE_MASK_DISABLED
+
+/**
+ * @brief   Trace buffer entries.
+ * @note    The trace buffer is only allocated if @p CH_DBG_TRACE_MASK is
+ *          different from @p CH_DBG_TRACE_MASK_DISABLED.
+ */
+#define CH_DBG_TRACE_BUFFER_SIZE            128
+
+/**
+ * @brief   Debug option, stack checks.
+ * @details If enabled then a runtime stack check is performed.
+ *
+ * @note    The default is @p FALSE.
+ * @note    The stack check is performed in a architecture/port dependent way.
+ *          It may not be implemented or some ports.
+ * @note    The default failure mode is to halt the system with the global
+ *          @p panic_msg variable set to @p NULL.
+ */
+#define CH_DBG_ENABLE_STACK_CHECK           TRUE
+
+/**
+ * @brief   Debug option, stacks initialization.
+ * @details If enabled then the threads working area is filled with a byte
+ *          value when a thread is created. This can be useful for the
+ *          runtime measurement of the used stack.
+ *
+ * @note    The default is @p FALSE.
+ */
+#define CH_DBG_FILL_THREADS                 FALSE
+
+/**
+ * @brief   Debug option, threads profiling.
+ * @details If enabled then a field is added to the @p thread_t structure that
+ *          counts the system ticks occurred while executing the thread.
+ *
+ * @note    The default is @p FALSE.
+ * @note    This debug option is not currently compatible with the
+ *          tickless mode.
+ */
+#define CH_DBG_THREADS_PROFILING            FALSE
+
+/** @} */
+
+/*===========================================================================*/
+/**
+ * @name Kernel hooks
+ * @{
+ */
+/*===========================================================================*/
+
+/**
+ * @brief   Threads descriptor structure extension.
+ * @details User fields added to the end of the @p thread_t structure.
+ */
+#define CH_CFG_THREAD_EXTRA_FIELDS                                          \
+  /* Add threads custom fields here.*/
+
+/**
+ * @brief   Threads initialization hook.
+ * @details User initialization code added to the @p chThdInit() API.
+ *
+ * @note    It is invoked from within @p chThdInit() and implicitly from all
+ *          the threads creation APIs.
+ */
+#define CH_CFG_THREAD_INIT_HOOK(tp) {                                       \
+  /* Add threads initialization code here.*/                                \
+}
+
+/**
+ * @brief   Threads finalization hook.
+ * @details User finalization code added to the @p chThdExit() API.
+ */
+#define CH_CFG_THREAD_EXIT_HOOK(tp) {                                       \
+  /* Add threads finalization code here.*/                                  \
+}
+
+/**
+ * @brief   Context switch hook.
+ * @details This hook is invoked just before switching between threads.
+ */
+#define CH_CFG_CONTEXT_SWITCH_HOOK(ntp, otp) {                              \
+  /* Context switch code here.*/                                            \
+}
+
+/**
+ * @brief   ISR enter hook.
+ */
+#define CH_CFG_IRQ_PROLOGUE_HOOK() {                                        \
+  /* IRQ prologue code here.*/                                              \
+}
+
+/**
+ * @brief   ISR exit hook.
+ */
+#define CH_CFG_IRQ_EPILOGUE_HOOK() {                                        \
+  /* IRQ epilogue code here.*/                                              \
+}
+
+/**
+ * @brief   Idle thread enter hook.
+ * @note    This hook is invoked within a critical zone, no OS functions
+ *          should be invoked from here.
+ * @note    This macro can be used to activate a power saving mode.
+ */
+#define CH_CFG_IDLE_ENTER_HOOK() {                                          \
+  /* Idle-enter code here.*/                                                \
+}
+
+/**
+ * @brief   Idle thread leave hook.
+ * @note    This hook is invoked within a critical zone, no OS functions
+ *          should be invoked from here.
+ * @note    This macro can be used to deactivate a power saving mode.
+ */
+#define CH_CFG_IDLE_LEAVE_HOOK() {                                          \
+  /* Idle-leave code here.*/                                                \
+}
+
+/**
+ * @brief   Idle Loop hook.
+ * @details This hook is continuously invoked by the idle thread loop.
+ */
+#define CH_CFG_IDLE_LOOP_HOOK() {                                           \
+  /* Idle loop code here.*/                                                 \
+}
+
+/**
+ * @brief   System tick event hook.
+ * @details This hook is invoked in the system tick handler immediately
+ *          after processing the virtual timers queue.
+ */
+#define CH_CFG_SYSTEM_TICK_HOOK() {                                         \
+  /* System tick event code here.*/                                         \
+}
+
+/**
+ * @brief   System halt hook.
+ * @details This hook is invoked in case to a system halting error before
+ *          the system is halted.
+ */
+#define CH_CFG_SYSTEM_HALT_HOOK(reason) {                                   \
+  /* System halt code here.*/                                               \
+}
+
+/**
+ * @brief   Trace hook.
+ * @details This hook is invoked each time a new record is written in the
+ *          trace buffer.
+ */
+#define CH_CFG_TRACE_HOOK(tep) {                                            \
+  /* Trace code here.*/                                                     \
+}
+
+/** @} */
+
+/*===========================================================================*/
+/* Port-specific settings (override port settings defaulted in chcore.h).    */
+/*===========================================================================*/
+
+#endif  /* CHCONF_H */
+
+/** @} */

keyboards/nk65/config.h

@@ -0,0 +1,154 @@
+/*
+Copyright 2019 Yiancar
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0x8968
+#define PRODUCT_ID      0x4E4B
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    Yiancar-Designs
+#define PRODUCT         NK65
+#define DESCRIPTION     A 65-percent, tool-free RGB keyboard
+
+/* key matrix size */
+#define MATRIX_ROWS 5
+#define MATRIX_COLS 15
+
+#define MATRIX_ROW_PINS { B3, B4, B5, A8, A4 }
+#define MATRIX_COL_PINS { A13, A10, A9, A14, A15, B8, B9, C13, C14, C15, A0, A1, A2, A3, A5 }
+// To enable debugger set A13 A14 -> A5 A7
+
+/* COL2ROW, ROW2COL*/
+#define DIODE_DIRECTION COL2ROW
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCING_DELAY 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* If defined, GRAVE_ESC will always act as ESC when CTRL is held.
+ * This is userful for the Windows task manager shortcut (ctrl+shift+esc).
+ */
+// #define GRAVE_ESC_CTRL_OVERRIDE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/* Backlight options */
+
+#define RGB_BACKLIGHT_ENABLED 1
+
+#define RGB_BACKLIGHT_NK65
+
+// they aren't really used if RGB_BACKLIGHT_HS60 defined
+#define RGB_BACKLIGHT_USE_SPLIT_BACKSPACE 0
+#define RGB_BACKLIGHT_USE_SPLIT_LEFT_SHIFT 0
+#define RGB_BACKLIGHT_USE_SPLIT_RIGHT_SHIFT 0
+#define RGB_BACKLIGHT_USE_7U_SPACEBAR 0
+#define RGB_BACKLIGHT_USE_ISO_ENTER 0
+#define RGB_BACKLIGHT_DISABLE_HHKB_BLOCKER_LEDS 0
+
+// disable backlight when USB suspended (PC sleep/hibernate/shutdown)
+#define RGB_BACKLIGHT_DISABLE_WHEN_USB_SUSPENDED 0
+
+// disable backlight after timeout in minutes, 0 = no timeout
+#define RGB_BACKLIGHT_DISABLE_AFTER_TIMEOUT 0
+
+// the default brightness
+#define RGB_BACKLIGHT_BRIGHTNESS 255
+
+// the default effect (RGB test)
+#define RGB_BACKLIGHT_EFFECT 255
+
+// the default effect speed (0-3)
+#define RGB_BACKLIGHT_EFFECT_SPEED 0
+
+// the default color1 and color2
+#define RGB_BACKLIGHT_COLOR_1 { .h = 0, .s = 255 }
+#define RGB_BACKLIGHT_COLOR_2 { .h = 127, .s = 255 }
+
+#define DRIVER_COUNT 2
+#define DRIVER_LED_TOTAL 128
+
+// These define which keys in the matrix are alphas/mods
+// Used for backlight effects so colors are different for
+// alphas vs. mods
+// Each value is for a row, bit 0 is column 0
+// Alpha=0 Mod=1
+#define RGB_BACKLIGHT_ALPHAS_MODS_ROW_0 0b0110000000000001
+#define RGB_BACKLIGHT_ALPHAS_MODS_ROW_1 0b0100000000000001
+#define RGB_BACKLIGHT_ALPHAS_MODS_ROW_2 0b0110000000000001
+#define RGB_BACKLIGHT_ALPHAS_MODS_ROW_3 0b0111000000000001
+#define RGB_BACKLIGHT_ALPHAS_MODS_ROW_4 0b0111111000000111
+
+#define RGB_BACKLIGHT_CAPS_LOCK_INDICATOR { .color = { .h = 0, .s = 0 }, .index = 255 }
+#define RGB_BACKLIGHT_LAYER_1_INDICATOR { .color = { .h = 0, .s = 0 }, .index = 255 }
+#define RGB_BACKLIGHT_LAYER_2_INDICATOR { .color = { .h = 0, .s = 0 }, .index = 255 }
+#define RGB_BACKLIGHT_LAYER_3_INDICATOR { .color = { .h = 0, .s = 0 }, .index = 255 }
+
+// TODO: refactor with new user EEPROM code (coming soon)
+#define EEPROM_MAGIC 0x451F
+#define EEPROM_MAGIC_ADDR 32
+// Bump this every time we change what we store
+// This will automatically reset the EEPROM with defaults
+// and avoid loading invalid data from the EEPROM
+#define EEPROM_VERSION 0x08
+#define EEPROM_VERSION_ADDR 34
+
+// Backlight config starts after EEPROM version
+#define RGB_BACKLIGHT_CONFIG_EEPROM_ADDR 35
+// Dynamic keymap starts after backlight config (35+32)
+#define DYNAMIC_KEYMAP_EEPROM_ADDR 67
+#define DYNAMIC_KEYMAP_LAYER_COUNT 4
+// Dynamic macro starts after dynamic keymaps (67+(4*5*15*2)) = (67+600)
+#define DYNAMIC_KEYMAP_MACRO_EEPROM_ADDR 667
+#define DYNAMIC_KEYMAP_MACRO_EEPROM_SIZE 398
+#define DYNAMIC_KEYMAP_MACRO_COUNT 16

keyboards/nk65/halconf.h

@@ -0,0 +1,388 @@
+/*
+    ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio
+
+    Licensed under the Apache License, Version 2.0 (the "License");
+    you may not use this file except in compliance with the License.
+    You may obtain a copy of the License at
+
+        http://www.apache.org/licenses/LICENSE-2.0
+
+    Unless required by applicable law or agreed to in writing, software
+    distributed under the License is distributed on an "AS IS" BASIS,
+    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+    See the License for the specific language governing permissions and
+    limitations under the License.
+*/
+
+/**
+ * @file    templates/halconf.h
+ * @brief   HAL configuration header.
+ * @details HAL configuration file, this file allows to enable or disable the
+ *          various device drivers from your application. You may also use
+ *          this file in order to override the device drivers default settings.
+ *
+ * @addtogroup HAL_CONF
+ * @{
+ */
+
+#ifndef HALCONF_H
+#define HALCONF_H
+
+#include "mcuconf.h"
+
+/**
+ * @brief   Enables the PAL subsystem.
+ */
+#if !defined(HAL_USE_PAL) || defined(__DOXYGEN__)
+#define HAL_USE_PAL                 TRUE
+#endif
+
+/**
+ * @brief   Enables the ADC subsystem.
+ */
+#if !defined(HAL_USE_ADC) || defined(__DOXYGEN__)
+#define HAL_USE_ADC                 FALSE
+#endif
+
+/**
+ * @brief   Enables the CAN subsystem.
+ */
+#if !defined(HAL_USE_CAN) || defined(__DOXYGEN__)
+#define HAL_USE_CAN                 FALSE
+#endif
+
+/**
+ * @brief   Enables the DAC subsystem.
+ */
+#if !defined(HAL_USE_DAC) || defined(__DOXYGEN__)
+#define HAL_USE_DAC                 TRUE
+#endif
+
+/**
+ * @brief   Enables the EXT subsystem.
+ */
+#if !defined(HAL_USE_EXT) || defined(__DOXYGEN__)
+#define HAL_USE_EXT                 FALSE
+#endif
+
+/**
+ * @brief   Enables the GPT subsystem.
+ */
+#if !defined(HAL_USE_GPT) || defined(__DOXYGEN__)
+#define HAL_USE_GPT                 TRUE
+#endif
+
+/**
+ * @brief   Enables the I2C subsystem.
+ */
+#if !defined(HAL_USE_I2C) || defined(__DOXYGEN__)
+#define HAL_USE_I2C                 TRUE
+#endif
+
+/**
+ * @brief   Enables the I2S subsystem.
+ */
+#if !defined(HAL_USE_I2S) || defined(__DOXYGEN__)
+#define HAL_USE_I2S                 FALSE
+#endif
+
+/**
+ * @brief   Enables the ICU subsystem.
+ */
+#if !defined(HAL_USE_ICU) || defined(__DOXYGEN__)
+#define HAL_USE_ICU                 FALSE
+#endif
+
+/**
+ * @brief   Enables the MAC subsystem.
+ */
+#if !defined(HAL_USE_MAC) || defined(__DOXYGEN__)
+#define HAL_USE_MAC                 FALSE
+#endif
+
+/**
+ * @brief   Enables the MMC_SPI subsystem.
+ */
+#if !defined(HAL_USE_MMC_SPI) || defined(__DOXYGEN__)
+#define HAL_USE_MMC_SPI             FALSE
+#endif
+
+/**
+ * @brief   Enables the PWM subsystem.
+ */
+#if !defined(HAL_USE_PWM) || defined(__DOXYGEN__)
+#define HAL_USE_PWM                 FALSE
+#endif
+
+/**
+ * @brief   Enables the QSPI subsystem.
+ */
+#if !defined(HAL_USE_QSPI) || defined(__DOXYGEN__)
+#define HAL_USE_QSPI                FALSE
+#endif
+
+/**
+ * @brief   Enables the RTC subsystem.
+ */
+#if !defined(HAL_USE_RTC) || defined(__DOXYGEN__)
+#define HAL_USE_RTC                 FALSE
+#endif
+
+/**
+ * @brief   Enables the SDC subsystem.
+ */
+#if !defined(HAL_USE_SDC) || defined(__DOXYGEN__)
+#define HAL_USE_SDC                 FALSE
+#endif
+
+/**
+ * @brief   Enables the SERIAL subsystem.
+ */
+#if !defined(HAL_USE_SERIAL) || defined(__DOXYGEN__)
+#define HAL_USE_SERIAL              FALSE
+#endif
+
+/**
+ * @brief   Enables the SERIAL over USB subsystem.
+ */
+#if !defined(HAL_USE_SERIAL_USB) || defined(__DOXYGEN__)
+#define HAL_USE_SERIAL_USB          TRUE
+#endif
+
+/**
+ * @brief   Enables the SPI subsystem.
+ */
+#if !defined(HAL_USE_SPI) || defined(__DOXYGEN__)
+#define HAL_USE_SPI                 FALSE
+#endif
+
+/**
+ * @brief   Enables the UART subsystem.
+ */
+#if !defined(HAL_USE_UART) || defined(__DOXYGEN__)
+#define HAL_USE_UART                FALSE
+#endif
+
+/**
+ * @brief   Enables the USB subsystem.
+ */
+#if !defined(HAL_USE_USB) || defined(__DOXYGEN__)
+#define HAL_USE_USB                 TRUE
+#endif
+
+/**
+ * @brief   Enables the WDG subsystem.
+ */
+#if !defined(HAL_USE_WDG) || defined(__DOXYGEN__)
+#define HAL_USE_WDG                 FALSE
+#endif
+
+/*===========================================================================*/
+/* ADC driver related settings.                                              */
+/*===========================================================================*/
+
+/**
+ * @brief   Enables synchronous APIs.
+ * @note    Disabling this option saves both code and data space.
+ */
+#if !defined(ADC_USE_WAIT) || defined(__DOXYGEN__)
+#define ADC_USE_WAIT                TRUE
+#endif
+
+/**
+ * @brief   Enables the @p adcAcquireBus() and @p adcReleaseBus() APIs.
+ * @note    Disabling this option saves both code and data space.
+ */
+#if !defined(ADC_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__)
+#define ADC_USE_MUTUAL_EXCLUSION    TRUE
+#endif
+
+/*===========================================================================*/
+/* CAN driver related settings.                                              */
+/*===========================================================================*/
+
+/**
+ * @brief   Sleep mode related APIs inclusion switch.
+ */
+#if !defined(CAN_USE_SLEEP_MODE) || defined(__DOXYGEN__)
+#define CAN_USE_SLEEP_MODE          TRUE
+#endif
+
+/*===========================================================================*/
+/* I2C driver related settings.                                              */
+/*===========================================================================*/
+
+/**
+ * @brief   Enables the mutual exclusion APIs on the I2C bus.
+ */
+#if !defined(I2C_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__)
+#define I2C_USE_MUTUAL_EXCLUSION    TRUE
+#endif
+
+/*===========================================================================*/
+/* MAC driver related settings.                                              */
+/*===========================================================================*/
+
+/**
+ * @brief   Enables an event sources for incoming packets.
+ */
+#if !defined(MAC_USE_ZERO_COPY) || defined(__DOXYGEN__)
+#define MAC_USE_ZERO_COPY           FALSE
+#endif
+
+/**
+ * @brief   Enables an event sources for incoming packets.
+ */
+#if !defined(MAC_USE_EVENTS) || defined(__DOXYGEN__)
+#define MAC_USE_EVENTS              TRUE
+#endif
+
+/*===========================================================================*/
+/* MMC_SPI driver related settings.                                          */
+/*===========================================================================*/
+
+/**
+ * @brief   Delays insertions.
+ * @details If enabled this options inserts delays into the MMC waiting
+ *          routines releasing some extra CPU time for the threads with
+ *          lower priority, this may slow down the driver a bit however.
+ *          This option is recommended also if the SPI driver does not
+ *          use a DMA channel and heavily loads the CPU.
+ */
+#if !defined(MMC_NICE_WAITING) || defined(__DOXYGEN__)
+#define MMC_NICE_WAITING            TRUE
+#endif
+
+/*===========================================================================*/
+/* SDC driver related settings.                                              */
+/*===========================================================================*/
+
+/**
+ * @brief   Number of initialization attempts before rejecting the card.
+ * @note    Attempts are performed at 10mS intervals.
+ */
+#if !defined(SDC_INIT_RETRY) || defined(__DOXYGEN__)
+#define SDC_INIT_RETRY              100
+#endif
+
+/**
+ * @brief   Include support for MMC cards.
+ * @note    MMC support is not yet implemented so this option must be kept
+ *          at @p FALSE.
+ */
+#if !defined(SDC_MMC_SUPPORT) || defined(__DOXYGEN__)
+#define SDC_MMC_SUPPORT             FALSE
+#endif
+
+/**
+ * @brief   Delays insertions.
+ * @details If enabled this options inserts delays into the MMC waiting
+ *          routines releasing some extra CPU time for the threads with
+ *          lower priority, this may slow down the driver a bit however.
+ */
+#if !defined(SDC_NICE_WAITING) || defined(__DOXYGEN__)
+#define SDC_NICE_WAITING            TRUE
+#endif
+
+/*===========================================================================*/
+/* SERIAL driver related settings.                                           */
+/*===========================================================================*/
+
+/**
+ * @brief   Default bit rate.
+ * @details Configuration parameter, this is the baud rate selected for the
+ *          default configuration.
+ */
+#if !defined(SERIAL_DEFAULT_BITRATE) || defined(__DOXYGEN__)
+#define SERIAL_DEFAULT_BITRATE      38400
+#endif
+
+/**
+ * @brief   Serial buffers size.
+ * @details Configuration parameter, you can change the depth of the queue
+ *          buffers depending on the requirements of your application.
+ * @note    The default is 16 bytes for both the transmission and receive
+ *          buffers.
+ */
+#if !defined(SERIAL_BUFFERS_SIZE) || defined(__DOXYGEN__)
+#define SERIAL_BUFFERS_SIZE         16
+#endif
+
+/*===========================================================================*/
+/* SERIAL_USB driver related setting.                                        */
+/*===========================================================================*/
+
+/**
+ * @brief   Serial over USB buffers size.
+ * @details Configuration parameter, the buffer size must be a multiple of
+ *          the USB data endpoint maximum packet size.
+ * @note    The default is 256 bytes for both the transmission and receive
+ *          buffers.
+ */
+#if !defined(SERIAL_USB_BUFFERS_SIZE) || defined(__DOXYGEN__)
+#define SERIAL_USB_BUFFERS_SIZE     1
+#endif
+
+/**
+ * @brief   Serial over USB number of buffers.
+ * @note    The default is 2 buffers.
+ */
+#if !defined(SERIAL_USB_BUFFERS_NUMBER) || defined(__DOXYGEN__)
+#define SERIAL_USB_BUFFERS_NUMBER   2
+#endif
+
+/*===========================================================================*/
+/* SPI driver related settings.                                              */
+/*===========================================================================*/
+
+/**
+ * @brief   Enables synchronous APIs.
+ * @note    Disabling this option saves both code and data space.
+ */
+#if !defined(SPI_USE_WAIT) || defined(__DOXYGEN__)
+#define SPI_USE_WAIT                TRUE
+#endif
+
+/**
+ * @brief   Enables the @p spiAcquireBus() and @p spiReleaseBus() APIs.
+ * @note    Disabling this option saves both code and data space.
+ */
+#if !defined(SPI_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__)
+#define SPI_USE_MUTUAL_EXCLUSION    TRUE
+#endif
+
+/*===========================================================================*/
+/* UART driver related settings.                                             */
+/*===========================================================================*/
+
+/**
+ * @brief   Enables synchronous APIs.
+ * @note    Disabling this option saves both code and data space.
+ */
+#if !defined(UART_USE_WAIT) || defined(__DOXYGEN__)
+#define UART_USE_WAIT               FALSE
+#endif
+
+/**
+ * @brief   Enables the @p uartAcquireBus() and @p uartReleaseBus() APIs.
+ * @note    Disabling this option saves both code and data space.
+ */
+#if !defined(UART_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__)
+#define UART_USE_MUTUAL_EXCLUSION   FALSE
+#endif
+
+/*===========================================================================*/
+/* USB driver related settings.                                              */
+/*===========================================================================*/
+
+/**
+ * @brief   Enables synchronous APIs.
+ * @note    Disabling this option saves both code and data space.
+ */
+#if !defined(USB_USE_WAIT) || defined(__DOXYGEN__)
+#define USB_USE_WAIT                TRUE
+#endif
+
+#endif /* HALCONF_H */
+
+/** @} */

keyboards/nk65/info.json

@@ -0,0 +1,12 @@
+{
+    "keyboard_name": "NK65", 
+    "url": "", 
+    "maintainer": "yiancar", 
+    "width": 16, 
+    "height": 5, 
+    "layouts": {
+        "LAYOUT": {
+            "layout": [{"label":"Esc", "x":0, "y":0}, {"label":"!", "x":1, "y":0}, {"label":"@", "x":2, "y":0}, {"label":"#", "x":3, "y":0}, {"label":"$", "x":4, "y":0}, {"label":"%", "x":5, "y":0}, {"label":"^", "x":6, "y":0}, {"label":"&", "x":7, "y":0}, {"label":"*", "x":8, "y":0}, {"label":"(", "x":9, "y":0}, {"label":")", "x":10, "y":0}, {"label":"_", "x":11, "y":0}, {"label":"+", "x":12, "y":0}, {"label":"Backspace", "x":13, "y":0, "w":2}, {"label":"Home", "x":15, "y":0}, {"label":"Tab", "x":0, "y":1, "w":1.5}, {"label":"Q", "x":1.5, "y":1}, {"label":"W", "x":2.5, "y":1}, {"label":"E", "x":3.5, "y":1}, {"label":"R", "x":4.5, "y":1}, {"label":"T", "x":5.5, "y":1}, {"label":"Y", "x":6.5, "y":1}, {"label":"U", "x":7.5, "y":1}, {"label":"I", "x":8.5, "y":1}, {"label":"O", "x":9.5, "y":1}, {"label":"P", "x":10.5, "y":1}, {"label":"{", "x":11.5, "y":1}, {"label":"}", "x":12.5, "y":1}, {"label":"|", "x":13.5, "y":1, "w":1.5}, {"label":"Page Up", "x":15, "y":1}, {"label":"Caps Lock", "x":0, "y":2, "w":1.75}, {"label":"A", "x":1.75, "y":2}, {"label":"S", "x":2.75, "y":2}, {"label":"D", "x":3.75, "y":2}, {"label":"F", "x":4.75, "y":2}, {"label":"G", "x":5.75, "y":2}, {"label":"H", "x":6.75, "y":2}, {"label":"J", "x":7.75, "y":2}, {"label":"K", "x":8.75, "y":2}, {"label":"L", "x":9.75, "y":2}, {"label":":", "x":10.75, "y":2}, {"label":"\"", "x":11.75, "y":2}, {"label":"Enter", "x":12.75, "y":2, "w":2.25}, {"label":"Page Down", "x":15, "y":2}, {"label":"Shift", "x":0, "y":3, "w":2.25}, {"label":"Z", "x":2.25, "y":3}, {"label":"X", "x":3.25, "y":3}, {"label":"C", "x":4.25, "y":3}, {"label":"V", "x":5.25, "y":3}, {"label":"B", "x":6.25, "y":3}, {"label":"N", "x":7.25, "y":3}, {"label":"M", "x":8.25, "y":3}, {"label":"<", "x":9.25, "y":3}, {"label":">", "x":10.25, "y":3}, {"label":"?", "x":11.25, "y":3}, {"label":"Shift", "x":12.25, "y":3, "w":1.75}, {"label":"\u2191", "x":14, "y":3}, {"label":"End", "x":15, "y":3}, {"label":"Ctrl", "x":0, "y":4, "w":1.25}, {"label":"Win", "x":1.25, "y":4, "w":1.25}, {"label":"Alt", "x":2.5, "y":4, "w":1.25}, {"x":3.75, "y":4, "w":6.25}, {"label":"Alt", "x":10, "y":4}, {"label":"Fn", "x":11, "y":4}, {"label":"Ctrl", "x":12, "y":4}, {"label":"\u2190", "x":13, "y":4}, {"label":"\u2193", "x":14, "y":4}, {"label":"\u2192", "x":15, "y":4}]
+        }
+    }
+}

keyboards/nk65/keymaps/default/keymap.c

@@ -0,0 +1,58 @@
+/* Copyright 2019 Yiancar
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include QMK_KEYBOARD_H
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+[0] = LAYOUT_65_ansi( /* Base */
+    KC_GESC, KC_1,    KC_2,   KC_3,   KC_4,   KC_5,   KC_6,   KC_7,   KC_8,    KC_9,    KC_0,    KC_MINS, KC_EQL,  KC_BSPC, KC_HOME,\
+    KC_TAB,  KC_Q,    KC_W,   KC_E,   KC_R,   KC_T,   KC_Y,   KC_U,   KC_I,    KC_O,    KC_P,    KC_LBRC, KC_RBRC, KC_BSLS, KC_PGUP,\
+    KC_CAPS, KC_A,    KC_S,   KC_D,   KC_F,   KC_G,   KC_H,   KC_J,   KC_K,    KC_L,    KC_SCLN, KC_QUOT,          KC_ENT,  KC_PGDN,\
+    KC_LSFT, KC_Z,    KC_X,   KC_C,   KC_V,   KC_B,   KC_N,   KC_M,   KC_COMM, KC_DOT,  KC_SLSH, KC_RSFT,          KC_UP,   KC_END, \
+    KC_LCTL, KC_LGUI, KC_LALT,                KC_SPC,                          KC_RALT, MO(1),   KC_RCTL, KC_LEFT, KC_DOWN, KC_RGHT),
+
+[1] = LAYOUT_65_ansi( /* FN */
+    KC_GRV,  KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,  KC_DEL,  KC_TRNS,\
+    KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, RESET,   KC_TRNS,\
+    KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, S1_DEC,  S1_INC,  S2_DEC,  S2_INC,  KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,          KC_TRNS, KC_TRNS,\
+    KC_TRNS, EF_DEC,  EF_INC,  H1_DEC,  H1_INC,  H2_DEC,  H2_INC,  BR_DEC,  BR_INC,  ES_DEC,  ES_INC,  KC_TRNS,          KC_TRNS, KC_TRNS,\
+    KC_VOLU, KC_VOLD, KC_MUTE,                KC_TRNS,                               KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS),
+
+[2] = LAYOUT_65_ansi( /* Empty for dynamic keymaps */
+    KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,\
+    KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,\
+    KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,          KC_TRNS, KC_TRNS,\
+    KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,          KC_TRNS, KC_TRNS,\
+    KC_TRNS, KC_TRNS, KC_TRNS,                KC_TRNS,                               KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS),
+
+[3] = LAYOUT_65_ansi( /* Empty for dynamic keymaps */
+    KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,\
+    KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,\
+    KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,          KC_TRNS, KC_TRNS,\
+    KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,          KC_TRNS, KC_TRNS,\
+    KC_TRNS, KC_TRNS, KC_TRNS,                KC_TRNS,                               KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS),
+};
+
+void matrix_init_user(void) {
+  //user initialization
+}
+
+void matrix_scan_user(void) {
+  //user matrix
+}
+
+bool process_record_user(uint16_t keycode, keyrecord_t *record) {
+  return true;
+}

keyboards/nk65/keymaps/default/readme.md

@@ -0,0 +1,6 @@
+The default keymap for NK65. VIA support disabled.
+=========================================================
+
+![Layout image](https://i.imgur.com/DL0CjJO.png)
+
+Default layer is normal ANSI 65%