Rgb matrix arm (#3648)

* Addition of I2C master driver for STM32, Generalization of ISSI3731 driver

- Addition of an i2c_master driver for STM32 to replicate expectations of AVR driver.
- Moved ISSI3731 driver one level up to make it accesible by both architectures.
- Renamed ISSI3731 functions to a more general name for preparation of other ISSI drivers.
- Added compiler directives where necessary to differenciate each architecture.

* converted tabs to spaces

CODE_OF_CONDUCT.md

@@ -1,10 +1,10 @@
 # Code Of Conduct
 
-QMK strives to be an inclusive and tolerant community. We welcome participation from anyone regardless of age, disability, ethnicity, gender identity and expression, level of experience, nationality, personal appearance, political belief, race, religion, or sexual identity and orientation. 
+QMK strives to be an inclusive, tolerant, and welcoming community. We encourage participation from anyone regardless of age, disability, ethnicity, gender identity and expression, level of experience, nationality, personal appearance, political belief, race, religion, or sexual identity and orientation.
 
-> “A gentle word turns away wrath, but a harsh word stirs up anger.”
+> “A gentle word turns away wrath, but a harsh word stirs up anger."
 
-Our users, contributors, and collaborators are expected to treat each other with respect, to assume good intentions, and to gently correct, where possible, rather than react with escalation. Some examples of behavior we will not tolerate include, but is not limited to:
+Our users, contributors, and collaborators are expected to treat each other with kindness and respect, to assume good intentions, and to gently correct, where possible, rather than react with escalation. While our goal is to be as accurate as possible, kindness and understanding are more valuable than correctness. Some examples of behavior we will not tolerate include, but is not limited to:
 
 * The use of sexualized language or imagery
 * Unwelcome advances, sexual or otherwise

build_keyboard.mk

@@ -1,3 +1,9 @@
+# Determine what keyboard we are building and setup the build environment.
+#
+# We support folders up to 5 levels deep below `keyboards/`. This file is
+# responsible for determining which folder is being used and doing the
+# corresponding environment setup.
+
 ifndef VERBOSE
 .SILENT:
 endif
@@ -6,26 +12,15 @@ endif
 
 include common.mk
 
-# 5/4/3/2/1
-KEYBOARD_FOLDER_PATH_1 := $(KEYBOARD)
-KEYBOARD_FOLDER_PATH_2 := $(patsubst %/,%,$(dir $(KEYBOARD_FOLDER_PATH_1)))
-KEYBOARD_FOLDER_PATH_3 := $(patsubst %/,%,$(dir $(KEYBOARD_FOLDER_PATH_2)))
-KEYBOARD_FOLDER_PATH_4 := $(patsubst %/,%,$(dir $(KEYBOARD_FOLDER_PATH_3)))
-KEYBOARD_FOLDER_PATH_5 := $(patsubst %/,%,$(dir $(KEYBOARD_FOLDER_PATH_4)))
-KEYBOARD_FOLDER_1 := $(notdir $(KEYBOARD_FOLDER_PATH_1))
-KEYBOARD_FOLDER_2 := $(notdir $(KEYBOARD_FOLDER_PATH_2))
-KEYBOARD_FOLDER_3 := $(notdir $(KEYBOARD_FOLDER_PATH_3))
-KEYBOARD_FOLDER_4 := $(notdir $(KEYBOARD_FOLDER_PATH_4))
-KEYBOARD_FOLDER_5 := $(notdir $(KEYBOARD_FOLDER_PATH_5))
-
+# Set the filename for the final firmware binary
 KEYBOARD_FILESAFE := $(subst /,_,$(KEYBOARD))
-
 TARGET ?= $(KEYBOARD_FILESAFE)_$(KEYMAP)
 KEYBOARD_OUTPUT := $(BUILD_DIR)/obj_$(KEYBOARD_FILESAFE)
 
 # Force expansion
 TARGET := $(TARGET)
 
+# For split boards we need to set a master half.
 MASTER ?= left
 ifdef master
     MASTER = $(master)
@@ -39,35 +34,58 @@ $(error MASTER does not have a valid value(left/right))
     endif
 endif
 
+# Determine which subfolders exist.
+KEYBOARD_FOLDER_PATH_1 := $(KEYBOARD)
+KEYBOARD_FOLDER_PATH_2 := $(patsubst %/,%,$(dir $(KEYBOARD_FOLDER_PATH_1)))
+KEYBOARD_FOLDER_PATH_3 := $(patsubst %/,%,$(dir $(KEYBOARD_FOLDER_PATH_2)))
+KEYBOARD_FOLDER_PATH_4 := $(patsubst %/,%,$(dir $(KEYBOARD_FOLDER_PATH_3)))
+KEYBOARD_FOLDER_PATH_5 := $(patsubst %/,%,$(dir $(KEYBOARD_FOLDER_PATH_4)))
+KEYBOARD_FOLDER_1 := $(notdir $(KEYBOARD_FOLDER_PATH_1))
+KEYBOARD_FOLDER_2 := $(notdir $(KEYBOARD_FOLDER_PATH_2))
+KEYBOARD_FOLDER_3 := $(notdir $(KEYBOARD_FOLDER_PATH_3))
+KEYBOARD_FOLDER_4 := $(notdir $(KEYBOARD_FOLDER_PATH_4))
+KEYBOARD_FOLDER_5 := $(notdir $(KEYBOARD_FOLDER_PATH_5))
 KEYBOARD_PATHS :=
-
 KEYBOARD_PATH_1 := keyboards/$(KEYBOARD_FOLDER_PATH_1)
 KEYBOARD_PATH_2 := keyboards/$(KEYBOARD_FOLDER_PATH_2)
 KEYBOARD_PATH_3 := keyboards/$(KEYBOARD_FOLDER_PATH_3)
 KEYBOARD_PATH_4 := keyboards/$(KEYBOARD_FOLDER_PATH_4)
 KEYBOARD_PATH_5 := keyboards/$(KEYBOARD_FOLDER_PATH_5)
 
-ifneq ("$(wildcard $(KEYBOARD_PATH_5)/rules.mk)","")
+ifneq ("$(wildcard $(KEYBOARD_PATH_5)/)","")
     KEYBOARD_PATHS += $(KEYBOARD_PATH_5)
+endif
+ifneq ("$(wildcard $(KEYBOARD_PATH_4)/)","")
+    KEYBOARD_PATHS += $(KEYBOARD_PATH_4)
+endif
+ifneq ("$(wildcard $(KEYBOARD_PATH_3)/)","")
+    KEYBOARD_PATHS += $(KEYBOARD_PATH_3)
+endif
+ifneq ("$(wildcard $(KEYBOARD_PATH_2)/)","")
+    KEYBOARD_PATHS += $(KEYBOARD_PATH_2)
+endif
+ifneq ("$(wildcard $(KEYBOARD_PATH_1)/)","")
+    KEYBOARD_PATHS += $(KEYBOARD_PATH_1)
+endif
+
+# Pull in rules.mk files from all our subfolders
+ifneq ("$(wildcard $(KEYBOARD_PATH_5)/rules.mk)","")
     include $(KEYBOARD_PATH_5)/rules.mk
 endif
 ifneq ("$(wildcard $(KEYBOARD_PATH_4)/rules.mk)","")
-    KEYBOARD_PATHS += $(KEYBOARD_PATH_4)
     include $(KEYBOARD_PATH_4)/rules.mk
 endif
 ifneq ("$(wildcard $(KEYBOARD_PATH_3)/rules.mk)","")
-    KEYBOARD_PATHS += $(KEYBOARD_PATH_3)
     include $(KEYBOARD_PATH_3)/rules.mk
 endif
 ifneq ("$(wildcard $(KEYBOARD_PATH_2)/rules.mk)","")
-    KEYBOARD_PATHS += $(KEYBOARD_PATH_2)
     include $(KEYBOARD_PATH_2)/rules.mk
 endif
 ifneq ("$(wildcard $(KEYBOARD_PATH_1)/rules.mk)","")
-    KEYBOARD_PATHS += $(KEYBOARD_PATH_1)
     include $(KEYBOARD_PATH_1)/rules.mk
 endif
 
+# Find all the C source files to be compiled in subfolders.
 KEYBOARD_SRC :=
 
 KEYBOARD_C_1 := $(KEYBOARD_PATH_1)/$(KEYBOARD_FOLDER_1).c
@@ -95,6 +113,15 @@ endif
 OPT_DEFS += -DKEYBOARD_$(KEYBOARD_FILESAFE)
 
 
+# Setup the define for QMK_KEYBOARD_H. This is used inside of keymaps so
+# that the same keymap may be used on multiple keyboards.
+#
+# We grab the most top-level include file that we can. That file should
+# use #ifdef statements to include all the neccesary subfolder includes,
+# as described here:
+#
+#    https://docs.qmk.fm/#/feature_layouts?id=tips-for-making-layouts-keyboard-agnostic
+#
 ifneq ("$(wildcard $(KEYBOARD_PATH_1)/$(KEYBOARD_FOLDER_1).h)","")
     QMK_KEYBOARD_H = $(KEYBOARD_FOLDER_1).h
 endif
@@ -111,13 +138,15 @@ ifneq ("$(wildcard $(KEYBOARD_PATH_5)/$(KEYBOARD_FOLDER_5).h)","")
     QMK_KEYBOARD_H = $(KEYBOARD_FOLDER_5).h
 endif
 
-# We can assume a ChibiOS target When MCU_FAMILY is defined , since it's not used for LUFA
+# Determine and set parameters based on the keyboard's processor family.
+# We can assume a ChibiOS target When MCU_FAMILY is defined since it's
+# not used for LUFA
 ifdef MCU_FAMILY
-    FIRMWARE_FORMAT=bin
+    FIRMWARE_FORMAT?=bin
     PLATFORM=CHIBIOS
 else
     PLATFORM=AVR
-    FIRMWARE_FORMAT=hex
+    FIRMWARE_FORMAT?=hex
 endif
 
 ifeq ($(PLATFORM),CHIBIOS)
@@ -148,6 +177,7 @@ ifeq ($(PLATFORM),CHIBIOS)
     endif
 endif
 
+# Find all of the config.h files and add them to our CONFIG_H define.
 CONFIG_H :=
 ifneq ("$(wildcard $(KEYBOARD_PATH_5)/config.h)","")
     CONFIG_H += $(KEYBOARD_PATH_5)/config.h
@@ -203,7 +233,7 @@ else
     # this state should never be reached
 endif
 
-# User space stuff
+# Userspace setup and definitions
 ifeq ("$(USER_NAME)","")
     USER_NAME := $(KEYMAP)
 endif
@@ -283,11 +313,6 @@ $(KEYBOARD_OUTPUT)_CONFIG := $(PROJECT_CONFIG)
 
 # Default target.
 all: build check-size
-
-# Change the build target to build a HEX file or a library.
 build: elf cpfirmware
-#build: elf hex eep lss sym
-#build: lib
-
 
 include $(TMK_PATH)/rules.mk

docs/_sidebar.md

@@ -44,8 +44,8 @@
   * [PS/2 Mouse](feature_ps2_mouse.md)
   * [RGB Lighting](feature_rgblight.md)
   * [RGB Matrix](feature_rgb_matrix.md)
-  * [Space Cadet Shift](feature_space_cadet.md)
-  * [Space Cadet Shift Enter](feature_space_shift_cadet.md)
+  * [Space Cadet Shift](feature_space_cadet_shift.md)
+  * [Space Cadet Shift Enter](feature_space_cadet_shift_enter.md)
   * [Stenography](feature_stenography.md)
   * [Swap Hands](feature_swap_hands.md)
   * [Tap Dance](feature_tap_dance.md)
@@ -68,11 +68,10 @@
   * [One Shot Keys](feature_advanced_keycodes.md#one-shot-keys)
   * [RGB Light](feature_rgblight.md#rgblight-keycodes)
   * [RGB Matrix](feature_rgb_matrix.md#keycodes)
-  * [Shifted Keys](feature_advanced_keycodes.md#shifted-keycodes)
+  * [Shifted Keys](keycodes_us_ansi_shifted.md)
   * [Stenography](feature_stenography.md#keycode-reference)
   * [Swap Hands](feature_swap_hands.md#swap-keycodes)
   * [Thermal Printer](feature_thermal_printer.md#thermal-printer-keycodes)
-  * [US ANSI Shifted Keys](keycodes_us_ansi_shifted.md)
 
 * Reference
   * [Config Options](config_options.md)

docs/_summary.md

@@ -44,8 +44,8 @@
   * [PS/2 Mouse](feature_ps2_mouse.md)
   * [RGB Lighting](feature_rgblight.md)
   * [RGB Matrix](feature_rgb_matrix.md)
-  * [Space Cadet Shift](feature_space_cadet.md)
-  * [Space Cadet Shift Enter](feature_space_shift_cadet.md)
+  * [Space Cadet Shift](feature_space_cadet_shift.md)
+  * [Space Cadet Shift Enter](feature_space_cadet_shift_enter.md)
   * [Stenography](feature_stenography.md)
   * [Swap Hands](feature_swap_hands.md)
   * [Tap Dance](feature_tap_dance.md)
@@ -68,11 +68,10 @@
   * [One Shot Keys](feature_advanced_keycodes.md#one-shot-keys)
   * [RGB Light](feature_rgblight.md#rgblight-keycodes)
   * [RGB Matrix](feature_rgb_matrix.md#keycodes)
-  * [Shifted Keys](feature_advanced_keycodes.md#shifted-keycodes)
+  * [Shifted Keys](keycodes_us_ansi_shifted.md)
   * [Stenography](feature_stenography.md#keycode-reference)
   * [Swap Hands](feature_swap_hands.md#swap-keycodes)
   * [Thermal Printer](feature_thermal_printer.md#thermal-printer-keycodes)
-  * [US ANSI Shifted Keys](keycodes_us_ansi_shifted.md)
 
 * Reference
   * [Config Options](config_options.md)

docs/config_options.md

@@ -91,6 +91,8 @@ This is a C header file that is one of the first things included, and will persi
   * key combination that allows the use of magic commands (useful for debugging)
 * `#define USB_MAX_POWER_CONSUMPTION`
   * sets the maximum power (in mA) over USB for the device (default: 500)
+* `#define SCL_CLOCK 100000L`
+  * sets the SCL_CLOCK speed for split keyboards. The default is `100000L` but some boards can be set to `400000L`.
 
 ## Features That Can Be Disabled
 
@@ -197,6 +199,8 @@ This is a [make](https://www.gnu.org/software/make/manual/make.html) file that i
 
 * `DEFAULT_FOLDER`
   * Used to specify a default folder when a keyboard has more than one sub-folder.
+* `FIRMWARE_FORMAT`
+  * Defines which format (bin, hex) is copied to the root `qmk_firmware` folder after building.
 * `SRC`
   * Used to add files to the compilation/linking list.
 * `LAYOUTS`

docs/faq_keymap.md

@@ -34,12 +34,11 @@ See [issue #168](https://github.com/tmk/tmk_keyboard/issues/168) and
 * http://en.wikipedia.org/wiki/Magic_SysRq_key
 * http://en.wikipedia.org/wiki/System_request
 
-## Power Key Doesn't Work
-Use `KC_PWR` instead of `KC_POWER` or vice versa.
-* `KC_PWR` works with Windows and Linux, not with OSX.
-* `KC_POWER` works with OSX and Linux, not with Windows.
+## Power Keys Aren't Working
 
-More info: http://geekhack.org/index.php?topic=14290.msg1327264#msg1327264
+Somewhat confusingly, there are two "Power" keycodes in QMK: `KC_POWER` in the Keyboard/Keypad HID usage page, and `KC_SYSTEM_POWER` (or `KC_PWR`) in the Consumer page.
+
+The former is only recognized on macOS, while the latter, `KC_SLEP` and `KC_WAKE` are supported by all three major operating systems, so it is recommended to use those instead. Under Windows, these keys take effect immediately, however on macOS they must be held down until a dialog appears.
 
 ## One Shot Modifier
 Solves my personal 'the' problem. I often got 'the' or 'THe' wrongly instead of 'The'.  One Shot Shift mitigates this for me.
@@ -87,14 +86,14 @@ On **Xorg** you can use `compose` key, instead.
 And see this for **Unicode** input.
 * http://en.wikipedia.org/wiki/Unicode_input
 
+## `Fn` Key on macOS
 
-## Apple/Mac Keyboard `Fn`
-Not supported.
+Unlike most Fn keys, the one on Apple keyboards actually has its own keycode... sort of. It takes the place of the sixth keycode in a basic 6KRO HID report -- so an Apple keyboard is in fact only 5KRO.
 
-Apple/Mac keyboard sends keycode for Fn unlike most of other keyboards.
-I think you can send Apple Fn key using Apple venter specific Page 0xff01 and usage 0x0003. But you have to change HID Report Descriptor for this, of course.
+It is technically possible to get QMK to send this key. However, doing so requires modification of the report format to add the state of the Fn key.
+Even worse, it is not recognized unless the keyboard's VID and PID match that of a real Apple keyboard. The legal issues that official QMK support for this feature may create mean it is unlikely to happen.
 
-https://opensource.apple.com/source/IOHIDFamily/IOHIDFamily-606.1.7/IOHIDFamily/AppleHIDUsageTables.h
+See [this issue](https://github.com/qmk/qmk_firmware/issues/2179) for detailed information.
 
 
 ## Media Control Keys in Mac OSX

docs/feature_advanced_keycodes.md

@@ -1,6 +1,6 @@
 # Advanced Keycodes
 
-Your keymap can include keycodes that are more advanced than normal, for example shifted keys. This page documents the functions that are available to you.
+Your keymap can include keycodes that are more advanced than normal, for example keys that switch layers or send modifiers when held, but send regular keycodes when tapped. This page documents the functions that are available to you.
 
 ### Assigning Custom Names
 
@@ -73,34 +73,6 @@ You can also chain these, like this:
 
     LALT(LCTL(KC_DEL)) -- this makes a key that sends Alt, Control, and Delete in a single keypress.
 
-# Shifted Keycodes
-
-The following shortcuts automatically add `LSFT()` to keycodes to get commonly used symbols.
-
-|Key                     |Aliases           |Description        |
-|------------------------|------------------|-------------------|
-|`KC_TILDE`              |`KC_TILD`         |`~`                |
-|`KC_EXCLAIM`            |`KC_EXLM`         |`!`                |
-|`KC_AT`                 |                  |`@`                |
-|`KC_HASH`               |                  |`#`                |
-|`KC_DOLLAR`             |`KC_DLR`          |`$`                |
-|`KC_PERCENT`            |`KC_PERC`         |`%`                |
-|`KC_CIRCUMFLEX`         |`KC_CIRC`         |`^`                |
-|`KC_AMPERSAND`          |`KC_AMPR`         |`&`                |
-|`KC_ASTERISK`           |`KC_ASTR`         |`*`                |
-|`KC_LEFT_PAREN`         |`KC_LPRN`         |`(`                |
-|`KC_RIGHT_PAREN`        |`KC_RPRN`         |`)`                |
-|`KC_UNDERSCORE`         |`KC_UNDS`         |`_`                |
-|`KC_PLUS`               |                  |`+`                |
-|`KC_LEFT_CURLY_BRACE`   |`KC_LCBR`         |`{`                |
-|`KC_RIGHT_CURLY_BRACE`  |`KC_RCBR`         |`}`                |
-|`KC_PIPE`               |                  |<code>&#124;</code>|
-|`KC_COLON`              |`KC_COLN`         |`:`                |
-|`KC_DOUBLE_QUOTE`       |`KC_DQT`/`KC_DQUO`|`"`                |
-|`KC_LEFT_ANGLE_BRACKET` |`KC_LT`/`KC_LABK` |`<`                |
-|`KC_RIGHT_ANGLE_BRACKET`|`KC_GT`/`KC_RABK` |`>`                |
-|`KC_QUESTION`           |`KC_QUES`         |`?`                |
-
 # Mod Tap
 
 `MT(mod, kc)` - is *mod* (modifier key - MOD_LCTL, MOD_LSFT) when held, and *kc* when tapped. In other words, you can have a key that sends Esc (or the letter O or whatever) when you tap it, but works as a Control key or a Shift key when you hold it down.
@@ -133,7 +105,7 @@ We've added shortcuts to make common modifier/tap (mod-tap) mappings more compac
 
 ?> Due to the way that keycodes are structured, any modifiers specified as part of `kc`, such as `LCTL()` or `KC_LPRN`, will only activate when held instead of tapped.
 
-?> Additionally, if there is at least one right modifier, any other modifiers will turn into their right equivalents, so it is not possible to "mix and match" the two.
+?> Additionally, if there is at least one right-handed modifier, any other modifiers in a chain of functions will turn into their right-handed equivalents, so it is not possible to "mix and match" the two.
 
 # One Shot Keys
 

docs/feature_backlight.md

@@ -1,10 +1,20 @@
 # Backlighting
 
-<!-- FIXME: Describe how backlighting works in QMK -->
+Many keyboards support backlit keys by way of individual LEDs placed through or underneath the keyswitches. QMK is able to control the brightness of these LEDs by switching them on and off rapidly in a certain ratio, a technique known as *Pulse Width Modulation*, or PWM. By altering the duty cycle of the PWM signal, it creates the illusion of dimming.
 
-## Backlight Keycodes
+The MCU can only supply so much current to its GPIO pins. Instead of powering the backlight directly from the MCU, the backlight pin is connected to a transistor or MOSFET that switches the power to the LEDs.
 
-These keycodes control the backlight. Most keyboards use this for single color in-switch lighting.
+## Usage
+
+Most keyboards have backlighting enabled by default if they support it, but if it is not working for you, check that your `rules.mk` includes the following:
+
+```make
+BACKLIGHT_ENABLE = yes
+```
+
+You should then be able to use the keycodes below to change the backlight level.
+
+## Keycodes
 
 |Key      |Description                               |
 |---------|------------------------------------------|
@@ -16,24 +26,28 @@ These keycodes control the backlight. Most keyboards use this for single color i
 |`BL_DEC` |Decrease the backlight level              |
 |`BL_BRTG`|Toggle backlight breathing                |
 
-Note that for backlight breathing, you need to have `#define BACKLIGHT_BREATHING` in your config.h.
+## Caveats
 
-## Configuration Options in `config.h`
+This feature is distinct from both the [RGB underglow](feature_rgblight.md) and [RGB matrix](feature_rgb_matrix.md) features as it usually allows for only a single colour per switch, though you can obviously use multiple different coloured LEDs on a keyboard.
 
-* `BACKLIGHT_PIN B7` defines the pin that controlls the LEDs. Unless you design your own keyboard, you don't need to set this.
-* `BACKLIGHT_LEVELS 3` defines the number of brightness levels (maximum 15 excluding off).
-* `BACKLIGHT_BREATHING` if defined, enables backlight breathing. Note that this is only available if `BACKLIGHT_PIN` is B5, B6 or B7.
-* `BREATHING_PERIOD 6` defines the length of one backlight "breath" in seconds.
+Hardware PWM is only supported on certain pins of the MCU, so if the backlighting is not connected to one of them, a software implementation will be used, and backlight breathing will not be available. Currently the supported pins are `B5`, `B6`, `B7`, and `C6`.
 
-## Notes on Implementation
+## Configuration
 
-To change the brightness when using pins B5, B6 or B7, the PWM (Pulse Width Modulation) functionality of the on-chip timer is used.
-The timer is a counter that counts up to a certain TOP value (`0xFFFF` set in ICR1) before resetting to 0.
-We also set an OCR1x register.
-When the counter reaches the value stored in that register, the PWM pin drops to low.
-The PWM pin is pulled high again when the counter resets to 0.
-Therefore, OCR1x basically sets the duty cycle of the LEDs and as such the brightness where `0` is the darkest and `0xFFFF` the brightest setting.
+To change the behaviour of the backlighting, `#define` these in your `config.h`:
 
-To enable the breathing effect, we register an interrupt handler to be called whenever the counter resets (with `ISR(TIMER1_OVF_vect)`).
-In this handler, which gets called roughly 244 times per second, we compute the desired brightness using a precomputed brightness curve.
-To disable breathing, we can just disable the respective interrupt vector and reset the brightness to the desired level.
+|Define               |Default      |Description                                                                                                  |
+|---------------------|-------------|-------------------------------------------------------------------------------------------------------------|
+|`BACKLIGHT_PIN`      |`B7`         |The pin that controls the LEDs. Unless you are designing your own keyboard, you shouldn't need to change this|
+|`BACKLIGHT_LEVELS`   |`3`          |The number of brightness levels (maximum 15 excluding off)                                                   |
+|`BACKLIGHT_BREATHING`|*Not defined*|Enable backlight breathing, if hardware PWM is used                                                          |
+|`BREATHING_PERIOD`   |`6`          |The length of one backlight "breath" in seconds                                                              |
+
+## Hardware PWM Implementation
+
+When using the supported pins for backlighting, QMK will use a hardware timer configured to output a PWM signal. This timer will count up to `ICRx` (by default `0xFFFF`) before resetting to 0.
+The desired brightness is calculated and stored in the `OCRxx` register. When the counter reaches this value, the backlight pin will go low, and is pulled high again when the counter resets.
+In this way `OCRxx` essentially controls the duty cycle of the LEDs, and thus the brightness, where `0x0000` is completely off and `0xFFFF` is completely on.
+
+The breathing effect is achieved by registering an interrupt handler for `TIMER1_OVF_vect` that is called whenever the counter resets, roughly 244 times per second.
+In this handler, the value of an incrementing counter is mapped onto a precomputed brightness curve. To turn off breathing, the interrupt handler is simply disabled, and the brightness reset to the level stored in EEPROM.

docs/feature_bootmagic.md

@@ -1,89 +1,100 @@
-# Bootmagic and Magic Keycodes
+# Bootmagic
 
-There are 3 separate but related features that allow you to change the behavior of your keyboard without reflashing. While each of them have similar functionality you access that functionality in different ways depending on how your keyboard is configured.
+There are three separate but related features that allow you to change the behavior of your keyboard without reflashing. While each of them have similar functionality, it is accessed in different ways depending on how your keyboard is configured.
 
-Bootmagic is a system for configuring your keyboard while it initializes. To trigger a Bootmagic command you hold down the bootmagic key (`KC_SPACE` on most keyboards) and one or more command keys.
+**Bootmagic** is a system for configuring your keyboard while it initializes. To trigger a Bootmagic command, hold down the Bootmagic key and one or more command keys.
 
-Bootmagic Keycodes allow you to access the Bootmagic functionality after your keyboard has initialized. To use Bootmagic Keycodes you assign keycodes starting with `MAGIC_`, much in the same way you define any other key.
+**Bootmagic Keycodes** are prefixed with `MAGIC_`, and allow you to access the Bootmagic functionality *after* your keyboard has initialized. To use the keycodes, assign them to your keymap as you would any other keycode.
 
-Command is a feature that allows you to control different aspects of your keyboard. Command used to be called Magic. Command is typically accessed by holding Left and Right Shift at the same time, although that can be customized. While it shares some functionality with Bootmagic it also allows you to access functionality that Bootmagic does not. For more information see the [Command](feature_command.md) documentation page.
+**Command**, formerly known as **Magic**, is another feature that allows you to control different aspects of your keyboard. While it shares some functionality with Bootmagic, it also allows you to do things that Bootmagic does not, such as printing version information to the console. For more information, see [Command](feature_command.md).
 
-## Enabling Bootmagic
+On some keyboards Bootmagic is disabled by default. If this is the case, it must be explicitly enabled in your `rules.mk` with:
 
-Bootmagic is disabled by default. To use Bootmagic you need to enable it in your `rules.mk` file:
+```make
+BOOTMAGIC_ENABLE = yes
+```
 
-    BOOTMAGIC_ENABLE = yes
+## Hotkeys
 
-## Bootmagic Hotkeys and Keycodes
+Hold down the Bootmagic key (Space by default) and the desired hotkey while plugging in your keyboard. For example, holding Space+`B` should cause it to enter the bootloader.
 
-This table describes the default Hotkeys for Bootmagic and the Keycodes for Magic. These may be overriden at the Keyboard or Keymap level. Some functionality is not available in both methods.
+|Hotkey            |Description                                  |
+|------------------|---------------------------------------------|
+|Escape            |Ignore Bootmagic configuration in EEPROM     |
+|`B`               |Enter the bootloader                         |
+|`D`               |Toggle debugging over serial                 |
+|`X`               |Toggle key matrix debugging                  |
+|`K`               |Toggle keyboard debugging                    |
+|`M`               |Toggle mouse debugging                       |
+|Backspace         |Clear the EEPROM                             |
+|Caps Lock         |Toggle treating Caps Lock as Left Control    |
+|Left Control      |Toggle swapping Caps Lock and Left Control   |
+|Left Alt          |Toggle swapping Left Alt and Left GUI        |
+|Right Alt         |Toggle swapping Right Alt and Right GUI      |
+|Left GUI          |Toggle the GUI keys (useful when gaming)     |
+|<code>&#96;</code>|Toggle swapping <code>&#96;</code> and Escape|
+|`\`               |Toggle swapping `\` and Backspace            |
+|`N`               |Toggle N-Key Rollover (NKRO)                 |
+|`0`               |Make layer 0 the default layer               |
+|`1`               |Make layer 1 the default layer               |
+|`2`               |Make layer 2 the default layer               |
+|`3`               |Make layer 3 the default layer               |
+|`4`               |Make layer 4 the default layer               |
+|`5`               |Make layer 5 the default layer               |
+|`6`               |Make layer 6 the default layer               |
+|`7`               |Make layer 7 the default layer               |
 
-To use the Hotkey hold down `BOOTMAGIC_KEY_SALT` (`KC_SPACE` by default) and the Hotkey while plugging in your keyboard. To use the Keycode assign that keycode to a layer. For example, if you hold down Space+B while plugging in most keyboards, you will enter bootloader mode.
+## Keycodes
 
-|Hotkey     |Keycode                           |Description                                             |
-|-----------|----------------------------------|--------------------------------------------------------|
-|`ESC`      |                                  |Skip bootmagic and saved eeprom configuration           |
-|`B`        |`RESET`                           |Enter bootloader instead of firmware                    |
-|`D`        |`DEBUG`                           |Enable debugging (writes messages to serial)            |
-|`X`        |                                  |Enable matrix debugging                                 |
-|`K`        |                                  |Enable keyboard debugging                               |
-|`M`        |                                  |Enable mouse debugging                                  |
-|`BACKSPACE`|                                  |Clear the saved settings from flash                     |
-|`CAPSLOCK` |`MAGIC_CAPSLOCK_TO_CONTROL`       |Treat `Capslock` as `Control`                           |
-|           |`MAGIC_UNCAPSLOCK_TO_CONTROL`     |Stop treating CapsLock as Control                       |
-|`LCTRL`    |`MAGIC_SWAP_CONTROL_CAPSLOCK`     |Swap `Control` and `Capslock`                           |
-|           |`MAGIC_UNSWAP_CONTROL_CAPSLOCK`   |Unswap Left Control and Caps Lock                       |
-|           |`MAGIC_SWAP_ALT_GUI`              |Swap Alt and GUI on both sides                          |
-|           |`MAGIC_UNSWAP_ALT_GUI`            |Unswap Left Alt and GUI                                 |
-|`LALT`     |`MAGIC_SWAP_LALT_LGUI`            |Swap Left `Alt` and `GUI`, e.g. for OSX Opt and Cmd     |
-|           |`MAGIC_UNSWAP_LALT_LGUI`          |Unswap Left Alt and GUI                                 |
-|`RALT`     |`MAGIC_SWAP_RALT_RGUI`            |Swap Right `Alt` and `GUI`                              |
-|           |`MAGIC_UNSWAP_RALT_RGUI`          |Unswap Right Alt and GUI                                |
-|`LGUI`     |`MAGIC_NO_GUI`                    |Disable GUI key - e.g. disable Windows key during gaming|
-|           |`MAGIC_UNNO_GUI`                  |Enable the GUI key                                      |
-|`GRAVE`    |`MAGIC_SWAP_GRAVE_ESC`            |Swap `\`~` and `ESC`                                    |
-|           |`MAGIC_UNSWAP_GRAVE_ESC`          |Unswap `\`~` and Escape                                 |
-|`BACKSLASH`|`MAGIC_SWAP_BACKSLASH_BACKSPACE`  |Swap Blackslash and Backspace                           |
-|           |`MAGIC_UNSWAP_BACKSLASH_BACKSPACE`|Unswap Backslash and Backspace                          |
-|`N`        |`MAGIC_HOST_NKRO`                 |Force N-Key Rollover (NKRO) on                          |
-|           |`MAGIC_UNHOST_NKRO`               |Force NKRO off                                          |
-|           |`MAGIC_TOGGLE_NKRO`               |Toggle NKRO on or off                                   |
-|`0`        |`DF(0)`                           |Make Layer 0 the default layer at bootup                |
-|`1`        |`DF(1)`                           |Make Layer 1 the default layer at bootup                |
-|`2`        |`DF(2)`                           |Make Layer 2 the default layer at bootup                |
-|`3`        |`DF(3)`                           |Make Layer 3 the default layer at bootup                |
-|`4`        |`DF(4)`                           |Make Layer 4 the default layer at bootup                |
-|`5`        |`DF(5)`                           |Make Layer 5 the default layer at bootup                |
-|`6`        |`DF(6)`                           |Make Layer 6 the default layer at bootup                |
-|`7`        |`DF(7)`                           |Make Layer 7 the default layer at bootup                |
+|Keycode                           |Aliases  |Description                               |
+|----------------------------------|---------|------------------------------------------|
+|`MAGIC_CAPSLOCK_TO_CONTROL`       |         |Treat Caps Lock as Left Control           |
+|`MAGIC_UNCAPSLOCK_TO_CONTROL`     |         |Stop treating Caps Lock as Left Control   |
+|`MAGIC_HOST_NKRO`                 |         |Force N-Key Rollover (NKRO) on            |
+|`MAGIC_UNHOST_NKRO`               |         |Force NKRO off                            |
+|`MAGIC_TOGGLE_NKRO`               |         |Turn NKRO on or off                       |
+|`MAGIC_NO_GUI`                    |         |Disable the GUI keys (useful when gaming) |
+|`MAGIC_UNNO_GUI`                  |         |Enable the GUI keys                       |
+|`MAGIC_SWAP_ALT_GUI`              |`AG_SWAP`|Swap Alt and GUI on both sides (for macOS)|
+|`MAGIC_UNSWAP_ALT_GUI`            |`AG_NORM`|Unswap Left Alt and Left GUI              |
+|`MAGIC_SWAP_BACKSLASH_BACKSPACE`  |         |Swap `\` and Backspace                    |
+|`MAGIC_UNSWAP_BACKSLASH_BACKSPACE`|         |Unswap `\` and Backspace                  |
+|`MAGIC_SWAP_CONTROL_CAPSLOCK`     |         |Swap Left Control and Caps Lock           |
+|`MAGIC_UNSWAP_CONTROL_CAPSLOCK`   |         |Unswap Left Control and Caps Lock         |
+|`MAGIC_SWAP_GRAVE_ESC`            |         |Swap <code>&#96;</code> and Escape        |
+|`MAGIC_UNSWAP_GRAVE_ESC`          |         |Unswap <code>&#96;</code> and Escape      |
+|`MAGIC_SWAP_LALT_LGUI`            |         |Swap Left Alt and Left GUI                |
+|`MAGIC_UNSWAP_LALT_LGUI`          |         |Unswap Left Alt and Left GUI              |
+|`MAGIC_SWAP_RALT_RGUI`            |         |Swap Right Alt and Right GUI              |
+|`MAGIC_UNSWAP_RALT_RGUI`          |         |Unswap Right Alt and Right GUI            |
 
-## Bootmagic Configuration
+## Configuration
 
-When setting up your keyboard and/or keymap there are a number of `#define`s that control the behavior of Bootmagic. To use these put them in your `config.h`, either at the keyboard or keymap level.
+If you would like to change the hotkey assignments for Bootmagic, `#define` these in your `config.h` at either the keyboard or keymap level.
 
-|Define |Default|Description |
-|-------|-------|------------|
-|`BOOTMAGIC_KEY_SALT`|`KC_SPACE`|The key to hold down to trigger Bootmagic during initialization.|
-|`BOOTMAGIC_KEY_SKIP`|`KC_ESC`|The Hotkey to ignore saved eeprom configuration.|
-|`BOOTMAGIC_KEY_EEPROM_CLEAR`|`KC_BSPACE`|The hotkey to clear the saved eeprom configuration.|
-|`BOOTMAGIC_KEY_BOOTLOADER`|`KC_B`|The hotkey to enter the bootloader.|
-|`BOOTMAGIC_KEY_DEBUG_ENABLE`|`KC_D`|The hotkey to enable debug mode.|
-|`BOOTMAGIC_KEY_DEBUG_MATRIX`|`KC_X`|The hotkey to enable matrix debugging mode.|
-|`BOOTMAGIC_KEY_DEBUG_KEYBOARD`|`KC_K`|The hotkey to enable keyboard debugging mode.|
-|`BOOTMAGIC_KEY_DEBUG_MOUSE`|`KC_M`|The hotkey to enable mouse debugging mode.|
-|`BOOTMAGIC_KEY_SWAP_CONTROL_CAPSLOCK`|`KC_LCTRL`||
-|`BOOTMAGIC_KEY_CAPSLOCK_TO_CONTROL`|`KC_CAPSLOCK`||
-|`BOOTMAGIC_KEY_SWAP_LALT_LGUI`|`KC_LALT`||
-|`BOOTMAGIC_KEY_SWAP_RALT_RGUI`|`KC_RALT`||
-|`BOOTMAGIC_KEY_NO_GUI`|`KC_LGUI`||
-|`BOOTMAGIC_KEY_SWAP_GRAVE_ESC`|`KC_GRAVE`||
-|`BOOTMAGIC_KEY_SWAP_BACKSLASH_BACKSPACE`|`KC_BSLASH`||
-|`BOOTMAGIC_HOST_NKRO`|`KC_N`||
-|`BOOTMAGIC_KEY_DEFAULT_LAYER_0`|`KC_0`|Hotkey to set Layer 0 as the default layer|
-|`BOOTMAGIC_KEY_DEFAULT_LAYER_1`|`KC_1`|Hotkey to set Layer 1 as the default layer|
-|`BOOTMAGIC_KEY_DEFAULT_LAYER_2`|`KC_2`|Hotkey to set Layer 2 as the default layer|
-|`BOOTMAGIC_KEY_DEFAULT_LAYER_3`|`KC_3`|Hotkey to set Layer 3 as the default layer|
-|`BOOTMAGIC_KEY_DEFAULT_LAYER_4`|`KC_4`|Hotkey to set Layer 4 as the default layer|
-|`BOOTMAGIC_KEY_DEFAULT_LAYER_5`|`KC_5`|Hotkey to set Layer 5 as the default layer|
-|`BOOTMAGIC_KEY_DEFAULT_LAYER_6`|`KC_6`|Hotkey to set Layer 6 as the default layer|
-|`BOOTMAGIC_KEY_DEFAULT_LAYER_7`|`KC_7`|Hotkey to set Layer 7 as the default layer|
+|Define                                  |Default      |Description                                        |
+|----------------------------------------|-------------|---------------------------------------------------|
+|`BOOTMAGIC_KEY_SALT`                    |`KC_SPACE`   |The Bootmagic key                                  |
+|`BOOTMAGIC_KEY_SKIP`                    |`KC_ESC`     |Ignore Bootmagic configuration in EEPROM           |
+|`BOOTMAGIC_KEY_EEPROM_CLEAR`            |`KC_BSPACE`  |Clear the EEPROM configuration                     |
+|`BOOTMAGIC_KEY_BOOTLOADER`              |`KC_B`       |Enter the bootloader                               |
+|`BOOTMAGIC_KEY_DEBUG_ENABLE`            |`KC_D`       |Toggle debugging over serial                       |
+|`BOOTMAGIC_KEY_DEBUG_MATRIX`            |`KC_X`       |Toggle matrix debugging                            |
+|`BOOTMAGIC_KEY_DEBUG_KEYBOARD`          |`KC_K`       |Toggle keyboard debugging                          |
+|`BOOTMAGIC_KEY_DEBUG_MOUSE`             |`KC_M`       |Toggle mouse debugging                             |
+|`BOOTMAGIC_KEY_SWAP_CONTROL_CAPSLOCK`   |`KC_LCTRL`   |Swap Left Control and Caps Lock                    |
+|`BOOTMAGIC_KEY_CAPSLOCK_TO_CONTROL`     |`KC_CAPSLOCK`|Toggle treating Caps Lock as Left Control          |
+|`BOOTMAGIC_KEY_SWAP_LALT_LGUI`          |`KC_LALT`    |Toggle swapping Left Alt and Left GUI (for macOS)  |
+|`BOOTMAGIC_KEY_SWAP_RALT_RGUI`          |`KC_RALT`    |Toggle swapping Right Alt and Right GUI (for macOS)|
+|`BOOTMAGIC_KEY_NO_GUI`                  |`KC_LGUI`    |Toggle the GUI keys (useful when gaming)           |
+|`BOOTMAGIC_KEY_SWAP_GRAVE_ESC`          |`KC_GRAVE`   |Toggle swapping <code>&#96;</code> and Escape      |
+|`BOOTMAGIC_KEY_SWAP_BACKSLASH_BACKSPACE`|`KC_BSLASH`  |Toggle swapping `\` and Backspace                  |
+|`BOOTMAGIC_HOST_NKRO`                   |`KC_N`       |Toggle N-Key Rollover (NKRO)                       |
+|`BOOTMAGIC_KEY_DEFAULT_LAYER_0`         |`KC_0`       |Make layer 0 the default layer                     |
+|`BOOTMAGIC_KEY_DEFAULT_LAYER_1`         |`KC_1`       |Make layer 1 the default layer                     |
+|`BOOTMAGIC_KEY_DEFAULT_LAYER_2`         |`KC_2`       |Make layer 2 the default layer                     |
+|`BOOTMAGIC_KEY_DEFAULT_LAYER_3`         |`KC_3`       |Make layer 3 the default layer                     |
+|`BOOTMAGIC_KEY_DEFAULT_LAYER_4`         |`KC_4`       |Make layer 4 the default layer                     |
+|`BOOTMAGIC_KEY_DEFAULT_LAYER_5`         |`KC_5`       |Make layer 5 the default layer                     |
+|`BOOTMAGIC_KEY_DEFAULT_LAYER_6`         |`KC_6`       |Make layer 6 the default layer                     |
+|`BOOTMAGIC_KEY_DEFAULT_LAYER_7`         |`KC_7`       |Make layer 7 the default layer                     |

docs/feature_command.md

@@ -1,52 +1,50 @@
-# Command (Formerly known as Magic)
+# Command
 
-Command is a way to change your keyboard's behavior without having to flash or unplug it to use [Bootmagic](feature_bootmagic.md). There is a lot of overlap between this functionality and the [Bootmagic Keycodes](feature_bootmagic.md). Whenever possible we encourage you to use that functionality instead of Command.
+Command, formerly known as Magic, is a way to change your keyboard's behavior without having to flash or unplug it to use [Bootmagic](feature_bootmagic.md). There is a lot of overlap between this functionality and the [Bootmagic Keycodes](feature_bootmagic.md#keycodes). Wherever possible we encourage you to use that feature instead of Command.
 
-## Enabling Command
+On some keyboards Command is disabled by default. If this is the case, it must be explicitly enabled in your `rules.mk`:
 
-By default Command is disabled. You can enable it in your `rules.mk` file:
-
-    COMMAND_ENABLE = yes
+```make
+COMMAND_ENABLE = yes
+```
 
 ## Usage
 
-To use Command you hold down the key combination defined by `IS_COMMAND`. By default that combination is both shift keys. While holding the key combination press the key corresponding to the command you want.
-
-For example, to write the current QMK version to the QMK Toolbox console, you can press `Left Shift`+`Right Shift`+`V`.
+To use Command, hold down the key combination defined by the `IS_COMMAND()` macro. By default this is Left Shift+Right Shift. Then, press the key corresponding to the command you want. For example, to output the current QMK version to the QMK Toolbox console, press Left Shift+Right Shift+`V`.
 
 ## Configuration
 
-The following values can be defined in `config.h` to control the behavior of Command.
+If you would like to change the key assignments for Command, `#define` these in your `config.h` at either the keyboard or keymap level. All keycode assignments here must omit the `KC_` prefix.
 
-|Define |Default | Description |
-|-------|--------|-------------|
-|`IS_COMMAND()`                      |`(keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)))`|Key combination to activate Command|
-|`MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS` |`true`                                                                |Do layer switching with Function row|
-|`MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS` |`true`                                                                |Do layer switching with number keys.|
-|`MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM`|`false`                                                               |Do layer switching with custom keys (`MAGIC_KEY_LAYER0..9` below.)|
-|`MAGIC_KEY_HELP1`                   |`H`                                                                   |Show help.|
-|`MAGIC_KEY_HELP2`                   |`SLASH`                                                               |Show help.|
-|`MAGIC_KEY_DEBUG`                   |`D`                                                                   |Turn on debug mode.|
-|`MAGIC_KEY_DEBUG_MATRIX`            |`X`                                                                   |Turn on matrix debugging.|
-|`MAGIC_KEY_DEBUG_KBD`               |`K`                                                                   |Turn on keyboard debugging.|
-|`MAGIC_KEY_DEBUG_MOUSE`             |`M`                                                                   |Turn on mouse debugging.|
-|`MAGIC_KEY_VERSION`                 |`V`                                                                   |Write the QMK version to the console|
-|`MAGIC_KEY_STATUS`                  |`S`                                                                   |Show the current keyboard status|
-|`MAGIC_KEY_CONSOLE`                 |`C`                                                                   |Enable the Command Console|
-|`MAGIC_KEY_LAYER0_ALT1`             |`ESC`                                                                 |Alternate access to layer 0|
-|`MAGIC_KEY_LAYER0_ALT2`             |`GRAVE`                                                               |Alternate access to layer 0|
-|`MAGIC_KEY_LAYER0`                  |`0`                                                                   |Change default layer to 0|
-|`MAGIC_KEY_LAYER1`                  |`1`                                                                   |Change default layer to 1|
-|`MAGIC_KEY_LAYER2`                  |`2`                                                                   |Change default layer to 2|
-|`MAGIC_KEY_LAYER3`                  |`3`                                                                   |Change default layer to 3|
-|`MAGIC_KEY_LAYER4`                  |`4`                                                                   |Change default layer to 4|
-|`MAGIC_KEY_LAYER5`                  |`5`                                                                   |Change default layer to 5|
-|`MAGIC_KEY_LAYER6`                  |`6`                                                                   |Change default layer to 6|
-|`MAGIC_KEY_LAYER7`                  |`7`                                                                   |Change default layer to 7|
-|`MAGIC_KEY_LAYER8`                  |`8`                                                                   |Change default layer to 8|
-|`MAGIC_KEY_LAYER9`                  |`9`                                                                   |Change default layer to 9|
-|`MAGIC_KEY_BOOTLOADER`              |`PAUSE`                                                               |Exit keyboard and enter bootloader|
-|`MAGIC_KEY_LOCK`                    |`CAPS`                                                                |Lock the keyboard so nothing can be typed|
-|`MAGIC_KEY_EEPROM`                  |`E`                                                                   |Erase EEPROM settings|
-|`MAGIC_KEY_NKRO`                    |`N`                                                                   |Toggle NKRO on/off|
-|`MAGIC_KEY_SLEEP_LED`               |`Z`                                                                   |Toggle LED when computer is sleeping on/off|
+|Define                              |Default                                                                               |Description                                     |
+|------------------------------------|--------------------------------------------------------------------------------------|------------------------------------------------|
+|`IS_COMMAND()`                      |<code>(keyboard_report->mods == (MOD_BIT(KC_LSHIFT) &#124; MOD_BIT(KC_RSHIFT)))</code>|The key combination to activate Command         |
+|`MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS` |`true`                                                                                |Set default layer with the Function row         |
+|`MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS` |`true`                                                                                |Set default layer with the number keys          |
+|`MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM`|`false`                                                                               |Set default layer with `MAGIC_KEY_LAYER0..9`    |
+|`MAGIC_KEY_DEBUG`                   |`D`                                                                                   |Toggle debugging over serial                    |
+|`MAGIC_KEY_DEBUG_MATRIX`            |`X`                                                                                   |Toggle key matrix debugging                     |
+|`MAGIC_KEY_DEBUG_KBD`               |`K`                                                                                   |Toggle keyboard debugging                       |
+|`MAGIC_KEY_DEBUG_MOUSE`             |`M`                                                                                   |Toggle mouse debugging                          |
+|`MAGIC_KEY_CONSOLE`                 |`C`                                                                                   |Enable the Command console                      |
+|`MAGIC_KEY_VERSION`                 |`V`                                                                                   |Print the running QMK version to the console    |
+|`MAGIC_KEY_STATUS`                  |`S`                                                                                   |Print the current keyboard status to the console|
+|`MAGIC_KEY_HELP1`                   |`H`                                                                                   |Print Command help to the console               |
+|`MAGIC_KEY_HELP2`                   |`SLASH`                                                                               |Print Command help to the console (alternate)   |
+|`MAGIC_KEY_LAYER0`                  |`0`                                                                                   |Make layer 0 the default layer                  |
+|`MAGIC_KEY_LAYER1`                  |`1`                                                                                   |Make layer 1 the default layer                  |
+|`MAGIC_KEY_LAYER2`                  |`2`                                                                                   |Make layer 2 the default layer                  |
+|`MAGIC_KEY_LAYER3`                  |`3`                                                                                   |Make layer 3 the default layer                  |
+|`MAGIC_KEY_LAYER4`                  |`4`                                                                                   |Make layer 4 the default layer                  |
+|`MAGIC_KEY_LAYER5`                  |`5`                                                                                   |Make layer 5 the default layer                  |
+|`MAGIC_KEY_LAYER6`                  |`6`                                                                                   |Make layer 6 the default layer                  |
+|`MAGIC_KEY_LAYER7`                  |`7`                                                                                   |Make layer 7 the default layer                  |
+|`MAGIC_KEY_LAYER8`                  |`8`                                                                                   |Make layer 8 the default layer                  |
+|`MAGIC_KEY_LAYER9`                  |`9`                                                                                   |Make layer 9 the default layer                  |
+|`MAGIC_KEY_LAYER0_ALT1`             |`ESC`                                                                                 |Make layer 0 the default layer (alternate)      |
+|`MAGIC_KEY_LAYER0_ALT2`             |`GRAVE`                                                                               |Make layer 0 the default layer (alternate)      |
+|`MAGIC_KEY_BOOTLOADER`              |`PAUSE`                                                                               |Enter the bootloader                            |
+|`MAGIC_KEY_LOCK`                    |`CAPS`                                                                                |Lock the keyboard so nothing can be typed       |
+|`MAGIC_KEY_EEPROM`                  |`E`                                                                                   |Clear the EEPROM                                |
+|`MAGIC_KEY_NKRO`                    |`N`                                                                                   |Toggle N-Key Rollover (NKRO)                    |
+|`MAGIC_KEY_SLEEP_LED`               |`Z`                                                                                   |Toggle LED when computer is sleeping            |

docs/feature_dynamic_macros.md

@@ -4,10 +4,10 @@ QMK supports temporary macros created on the fly. We call these Dynamic Macros.
 
 You can store one or two macros and they may have a combined total of 128 keypresses. You can increase this size at the cost of RAM.
 
-To enable them, first add a new element to the `planck_keycodes` enum — `DYNAMIC_MACRO_RANGE`:
+To enable them, first add a new element to the end of your `keycodes` enum — `DYNAMIC_MACRO_RANGE`:
 
 ```c
-enum planck_keycodes {
+enum keycodes {
 	QWERTY = SAFE_RANGE,
 	COLEMAK,
 	DVORAK,
@@ -20,7 +20,7 @@ enum planck_keycodes {
 };
 ```
 
-It must be the last element because `dynamic_macros.h` will add some more keycodes after it.
+Your `keycodes` enum may have a slightly different name. You must add `DYNAMIC_MACRO_RANGE` as the last element because `dynamic_macros.h` will add some more keycodes after it.
 
 Below it, include the `dynamic_macro.h` header:
 

docs/feature_grave_esc.md

@@ -1,17 +1,24 @@
 # Grave Escape
 
-Grave Escape is a feature that allows you to share the grave key (<code>&#96;</code> and `~`) on the same key as Escape. When `KC_GESC` is used it will act as `KC_ESC`, unless Shift or GUI is pressed, in which case it will act as `KC_GRAVE`.
+If you're using a 60% keyboard, or any other layout with no F-row, you will have noticed that there is no dedicated Escape key. Grave Escape is a feature that allows you to share the grave key (<code>&#96;</code> and `~`) with Escape.
 
+## Usage
+
+Replace the `KC_GRAVE` key in your keymap (usually to the left of the `1` key) with `KC_GESC`. When pressed it will behave like `KC_ESC`, but with Shift or GUI held it will send `KC_GRAVE`.
+
+## Keycodes
 
 |Key      |Aliases    |Description                                                       |
 |---------|-----------|------------------------------------------------------------------|
 |`KC_GESC`|`GRAVE_ESC`|Escape when pressed, <code>&#96;</code> when Shift or GUI are held|
 
-There are several possible key combinations this will break, among them Ctrl+Shift+Esc on Windows and Cmd+Opt+Esc on macOS. You can use these options in your `config.h` to work around this:
+## Configuration
 
-| Option | Description |
-|--------|-------------|
-| `GRAVE_ESC_ALT_OVERRIDE` | Always send Escape if Alt is pressed. |
-| `GRAVE_ESC_CTRL_OVERRIDE` | Always send Escape if Ctrl is pressed. |
-| `GRAVE_ESC_GUI_OVERRIDE` | Always send Escape if GUI is pressed. |
-| `GRAVE_ESC_SHIFT_OVERRIDE` | Always send Escape if SHIFT is pressed. |
+There are several possible key combinations this will break, among them Control+Shift+Escape on Windows and Command+Option+Escape on macOS. To work around this, you can `#define` these options in your `config.h`:
+
+|Define                    |Description                              |
+|--------------------------|-----------------------------------------|
+|`GRAVE_ESC_ALT_OVERRIDE`  |Always send Escape if Alt is pressed     |
+|`GRAVE_ESC_CTRL_OVERRIDE` |Always send Escape if Control is pressed |
+|`GRAVE_ESC_GUI_OVERRIDE`  |Always send Escape if GUI is pressed     |
+|`GRAVE_ESC_SHIFT_OVERRIDE`|Always send Escape if Shift is pressed   |

docs/feature_key_lock.md

@@ -1,11 +1,22 @@
-## Key Lock: Holding Down Keys for You
+# Key Lock
 
-Sometimes, you need to hold down a specific key for a long period of time. Whether this is while typing in ALL CAPS, or playing a video game that hasn't implemented auto-run, Key Lock is here to help. Key Lock adds a new keycode, `KC_LOCK`, that will hold down the next key you hit for you. The key is released when you hit it again. Here's an example: let's say you need to type in all caps for a few sentences. You hit KC_LOCK, and then shift. Now, shift will be considered held until you hit it again. You can think of key lock as caps lock, but supercharged.
+Sometimes you may find yourself needing to hold down a specific key for a long period of time. Key Lock holds down the next key you press for you. Press it again, and it will be released.
 
-Here's how to use it:
+Let's say you need to type in ALL CAPS for a few sentences. Hit `KC_LOCK`, and then Shift. Now, Shift will be considered held until you tap it again. You can think of Key Lock as Caps Lock, but supercharged.
 
-1. Pick a key on your keyboard. This will be the key lock key. Assign it the keycode `KC_LOCK`. This will be a single-action key: you won't be able to use it for anything else.
-2. Enable key lock by including `KEY_LOCK_ENABLE = yes` in your Makefile.
-3. That's it!
+## Usage
 
-Important: switching layers does not cancel the key lock. Additionally, key lock is only able to hold standard action keys and One Shot modifier keys (for example, if you have your shift defined as `OSM(KC_LSFT)`; see [One Shot Keys](quantum_keycodes.md#one-shot-keys)). This does not include any of the QMK special functions (except One Shot modifiers), or shifted versions of keys such as KC_LPRN. If it's in the [Basic Keycodes](keycodes_basic.md) list, it can be held. If it's not, then it can't be.
+First, enable Key Lock by setting `KEY_LOCK_ENABLE = yes` in your `rules.mk`. Then pick a key in your keymap and assign it the keycode `KC_LOCK`.
+
+## Keycodes
+
+|Keycode  |Description                                                   |
+|---------|--------------------------------------------------------------|
+|`KC_LOCK`|Hold down the next key pressed, until the key is pressed again|
+
+## Caveats
+
+Key Lock is only able to hold standard action keys and [One Shot modifier](quantum_keycodes.md#one-shot-keys) keys (for example, if you have your Shift defined as `OSM(KC_LSFT)`).
+This does not include any of the QMK special functions (except One Shot modifiers), or shifted versions of keys such as `KC_LPRN`. If it's in the [Basic Keycodes](keycodes_basic.md) list, it can be held.
+
+Switching layers will not cancel the Key Lock.

docs/feature_rgb_matrix.md

@@ -80,7 +80,7 @@ All RGB keycodes are currently shared with the RGBLIGHT system:
 These are the effects that are currently available:
 
 	enum rgb_matrix_effects {
-		RGB_MATRIX_SOLID_COLOR = 1,
+	    RGB_MATRIX_SOLID_COLOR = 1,
 	    RGB_MATRIX_ALPHAS_MODS,
 	    RGB_MATRIX_DUAL_BEACON,
 	    RGB_MATRIX_GRADIENT_UP_DOWN,
@@ -93,7 +93,7 @@ These are the effects that are currently available:
 	    RGB_MATRIX_RAINBOW_MOVING_CHEVRON,
 	    RGB_MATRIX_JELLYBEAN_RAINDROPS,
 	#ifdef RGB_MATRIX_KEYPRESSES
-		RGB_MATRIX_SOLID_REACTIVE,
+	    RGB_MATRIX_SOLID_REACTIVE,
 	    RGB_MATRIX_SPLASH,
 	    RGB_MATRIX_MULTISPLASH,
 	    RGB_MATRIX_SOLID_SPLASH,
@@ -107,7 +107,7 @@ These are the effects that are currently available:
 Custom layer effects can be done by defining this in your `<keyboard>.c`:
 
     void rgb_matrix_indicators_kb(void) {
-    	// rgb_matrix_set_color(index, red, green, blue);
+        rgb_matrix_set_color(index, red, green, blue);
     }
 
 A similar function works in the keymap as `rgb_matrix_indicators_user`.

docs/feature_rgblight.md

@@ -1,131 +1,46 @@
 # RGB Lighting
 
-If you've installed addressable RGB lights on your keyboard you can control them with QMK. Currently we support the following addressable LEDs on Atmel AVR processors:
+QMK has the ability to control RGB LEDs attached to your keyboard. This is commonly called *underglow*, due to the LEDs often being mounted on the bottom of the keyboard, producing a nice diffused effect when combined with a translucent case.
 
-* WS2811 and variants (WS2812, WS2812B, WS2812C, etc)
-* SK6812RGBW
+![Planck with RGB Underglow](https://raw.githubusercontent.com/qmk/qmk_firmware/3774a7fcdab5544fc787f4c200be05fcd417e31f/keyboards/planck/keymaps/yang/planck-with-rgb-underglow.jpg)
 
-Some keyboards come with RGB LEDs pre-installed. Others have to have LEDs installed after the fact. See below for information on modifying your keyboard.
+Some keyboards come with RGB LEDs preinstalled. Others must have them installed after the fact. See the [Hardware Modification](#hardware-modification) section for information on adding RGB lighting to your keyboard.
 
-## Selecting Colors
+Currently QMK supports the following addressable LEDs on AVR microcontrollers (however, the white LED in RGBW variants is not supported):
 
-QMK uses Hue, Saturation, and Value to set color rather than using RGB. You can use the color wheel below to see how this works. Changing the Hue will cycle around the circle. Saturation will affect the intensity of the color, which you can see as you move from the inner part to the outer part of the wheel. Value sets the overall brightness.
+ * WS2811, WS2812, WS2812B, WS2812C, etc.
+ * SK6812, SK6812MINI, SK6805
 
-<img src="gitbook/images/color-wheel.svg" alt="HSV Color Wheel" width="250">
+These LEDs are called "addressable" because instead of using a wire per color, each LED contains a small microchip that understands a special protocol sent over a single wire. The chip passes on the remaining data to the next LED, allowing them to be chained together. In this way, you can easily control the color of the individual LEDs.
 
-If you would like to learn more about HSV you can start with the [Wikipedia article](https://en.wikipedia.org/wiki/HSL_and_HSV).
+## Usage
 
-## Configuration
+On keyboards with onboard RGB LEDs, it is usually enabled by default. If it is not working for you, check that your `rules.mk` includes the following:
 
-Before RGB Lighting can be used you have to enable it in `rules.mk`:
-
-    RGBLIGHT_ENABLE = yes
-
-You can configure the behavior of the RGB lighting by defining values inside `config.h`.
-
-### Required Configuration
-
-At minimum you have to define the pin your LED strip is connected to and the number of LEDs connected.
-
-```c
-#define RGB_DI_PIN D7     // The pin the LED strip is connected to
-#define RGBLED_NUM 14     // Number of LEDs in your strip
+```make
+RGBLIGHT_ENABLE = yes
 ```
 
-### Optional Configuration
+At minimum you must define the data pin your LED strip is connected to, and the number of LEDs in the strip, in your `config.h`. If your keyboard has onboard RGB LEDs, and you are simply creating a keymap, you usually won't need to modify these.
 
-You can change the behavior of the RGB Lighting by setting these configuration values. Use `#define <Option> <Value>` in a `config.h` at the keyboard, revision, or keymap level.
+|Define      |Description                                  |
+|------------|---------------------------------------------|
+|`RGB_DI_PIN`|The pin connected to the data pin of the LEDs|
+|`RGBLED_NUM`|The number of LEDs connected                 |
 
-| Option | Default Value | Description |
-|--------|---------------|-------------|
-| `RGBLIGHT_HUE_STEP` | 10 | How many hues you want to have available. |
-| `RGBLIGHT_SAT_STEP` | 17 | How many steps of saturation you'd like. |
-| `RGBLIGHT_VAL_STEP` | 17 | The number of levels of brightness you want. |
-| `RGBLIGHT_LIMIT_VAL` | 255 | Limit the val of HSV to limit the maximum brightness simply. |
-| `RGBLIGHT_SLEEP`     |    |  `#define` this will shut off the lights when the host goes to sleep | 
+Then you should be able to use the keycodes below to change the RGB lighting to your liking.
 
+### Color Selection
 
-### Animations
+QMK uses [Hue, Saturation, and Value](https://en.wikipedia.org/wiki/HSL_and_HSV) to select colors rather than RGB. The color wheel below demonstrates how this works.
 
-If you have `#define RGBLIGHT_ANIMATIONS` in your `config.h` you will have a number of animation modes you can cycle through using the `RGB_MOD` key. You can also `#define` other options to tweak certain animations.
+<img src="gitbook/images/color-wheel.svg" alt="HSV Color Wheel" width="250"/>
 
-| Option | Default Value | Description |
-|--------|---------------|-------------|
-| `RGBLIGHT_ANIMATIONS` | | `#define` this to enable animation modes. |
-| `RGBLIGHT_EFFECT_BREATHE_CENTER` | 1.85 | Used to calculate the curve for the breathing animation. Valid values 1.0-2.7. |
-| `RGBLIGHT_EFFECT_BREATHE_MAX` | 255 | The maximum brightness for the breathing mode. Valid values 1-255. |
-| `RGBLIGHT_EFFECT_SNAKE_LENGTH` | 4 | The number of LEDs to light up for the "snake" animation. |
-| `RGBLIGHT_EFFECT_KNIGHT_LENGTH` | 3 | The number of LEDs to light up for the "knight" animation. |
-| `RGBLIGHT_EFFECT_KNIGHT_OFFSET` | 0 | Start the knight animation this many LEDs from the start of the strip. |
-| `RGBLIGHT_EFFECT_KNIGHT_LED_NUM` | RGBLED_NUM | The number of LEDs to have the "knight" animation travel. |
-| `RGBLIGHT_EFFECT_CHRISTMAS_INTERVAL` | 1000 | How long to wait between light changes for the "christmas" animation. Specified in ms. |
-| `RGBLIGHT_EFFECT_CHRISTMAS_STEP` | 2 | How many LED's to group the red/green colors by for the christmas mode. |
+Changing the **Hue** cycles around the circle.  
+Changing the **Saturation** moves between the inner and outer sections of the wheel, affecting the intensity of the color.  
+Changing the **Value** sets the overall brightness.
 
-You can also tweak the behavior of the animations by defining these consts in your `keymap.c`. These mostly affect the speed different modes animate at.
-
-```c
-// How long (in ms) to wait between animation steps for the breathing mode
-const uint8_t RGBLED_BREATHING_INTERVALS[] PROGMEM = {30, 20, 10, 5};
-
-// How long (in ms) to wait between animation steps for the rainbow mode
-const uint8_t RGBLED_RAINBOW_MOOD_INTERVALS[] PROGMEM = {120, 60, 30};
-
-// How long (in ms) to wait between animation steps for the swirl mode
-const uint8_t RGBLED_RAINBOW_SWIRL_INTERVALS[] PROGMEM = {100, 50, 20};
-
-// How long (in ms) to wait between animation steps for the snake mode
-const uint8_t RGBLED_SNAKE_INTERVALS[] PROGMEM = {100, 50, 20};
-
-// How long (in ms) to wait between animation steps for the knight modes
-const uint8_t RGBLED_KNIGHT_INTERVALS[] PROGMEM = {127, 63, 31};
-
-// These control which colors are selected for the gradient mode
-const uint16_t RGBLED_GRADIENT_RANGES[] PROGMEM = {360, 240, 180, 120, 90};
-```
-
-### LED Control
-
-Look in `rgblights.h` for all available functions, but if you want to control all or some LEDs your goto functions are:
-
-```c
-// turn all lights off (stored in EEPROM)
-rgblight_disable();
-// turn lights on, based on their previous state (stored in EEPROM)
-rgblight_enable(); 
-
-// turn all lights off (not stored in EEPROM)
-rgblight_disable_noeeprom();
-// turn lights on, based on their previous state (not stored in EEPROM)
-rgblight_enable_noeeprom();
-
-// where r/g/b is a number from 0..255.  Turns all the LEDs to this color (ignores mode, not stored in EEPROM). 
-rgblight_setrgb(r, g, b); 
-// HSV color control - h is a value from 0..360 and s/v is a value from 0..255 (stored in EEPROM)
-rgblight_sethsv(h, s, v);  
-// HSV color control - h is a value from 0..360 and s/v is a value from 0..255 (not stored in EEPROM)
-rgblight_sethsv_noeeprom(h, s, v);  
-
-// Sets the mode, if rgb animations are enabled (stored in eeprom)
-rgblight_mode(x);
-// Sets the mode, if rgb animations are enabled (not stored in eeprom)
-rgblight_mode_noeeprom(x);
-// MODE 1, solid color
-// MODE 2-5, breathing
-// MODE 6-8, rainbow mood
-// MODE 9-14, rainbow swirl
-// MODE 15-20, snake
-// MODE 21-23, knight
-// MODE 24, xmas
-// MODE 25-34, static rainbow
-
-rgblight_setrgb_at(r,g,b, LED);  // control a single LED.  0 <= LED < RGBLED_NUM
-rgblight_sethsv_at(h,s,v, LED);  // control a single LED.  0 <= LED < RGBLED_NUM
-```
-You can find a list of predefined colors at [`quantum/rgblight_list.h`](https://github.com/qmk/qmk_firmware/blob/master/quantum/rgblight_list.h). Free to add to this list!
-
-## RGB Lighting Keycodes
-
-These control the RGB Lighting functionality.
+## Keycodes
 
 |Key                |Aliases   |Description                                                         |
 |-------------------|----------|--------------------------------------------------------------------|
@@ -146,25 +61,97 @@ These control the RGB Lighting functionality.
 |`RGB_MODE_KNIGHT`  |`RGB_M_K` |"Knight Rider" animation mode                                       |
 |`RGB_MODE_XMAS`    |`RGB_M_X` |Christmas animation mode                                            |
 |`RGB_MODE_GRADIENT`|`RGB_M_G` |Static gradient animation mode                                      |
-|`RGB_MODE_RGBTEST `|`RGB_M_T` |Red,Green,Blue test animation mode                                  |
+|`RGB_MODE_RGBTEST` |`RGB_M_T` |Red, Green, Blue test animation mode                                |
 
-note: for backwards compatibility, `RGB_SMOD` is an alias for `RGB_MOD`.
+?> For backwards compatibility, `RGB_SMOD` is another alias of `RGB_MOD`.
+
+## Configuration
+
+Your RGB lighting can be configured by placing these `#define`s in your `config.h`:
+
+|Define               |Default      |Description                                                                  |
+|---------------------|-------------|-----------------------------------------------------------------------------|
+|`RGBLIGHT_HUE_STEP`  |`10`         |The number of steps to cycle through the hue by                              |
+|`RGBLIGHT_SAT_STEP`  |`17`         |The number of steps to increment the saturation by                           |
+|`RGBLIGHT_VAL_STEP`  |`17`         |The number of steps to increment the brightness by                           |
+|`RGBLIGHT_LIMIT_VAL` |`255`        |The maximum brightness level                                                 |
+|`RGBLIGHT_SLEEP`     |*Not defined*|If defined, the RGB lighting will be switched off when the host goes to sleep|
+
+## Animations
+
+Not only can this lighting be whatever color you want, if `RGBLIGHT_ANIMATIONS` is defined, you also have a number of animation modes at your disposal:
+
+|Mode |Description          |
+|-----|---------------------|
+|1    |Solid color          |
+|2-5  |Solid color breathing|
+|6-8  |Cycling rainbow      |
+|9-14 |Swirling rainbow     |
+|15-20|Snake                |
+|21-23|Knight               |
+|24   |Christmas            |
+|25-34|Static gradient      |
+|35   |RGB Test             |
+|36   |Alternating          |
+
+Check out [this video](https://youtube.com/watch?v=VKrpPAHlisY) for a demonstration.
+
+The following options can be used to tweak the various animations:
+
+|Define                              |Default      |Description                                                                          |
+|------------------------------------|-------------|-------------------------------------------------------------------------------------|
+|`RGBLIGHT_ANIMATIONS`               |*Not defined*|If defined, enables additional animation modes                                       |
+|`RGBLIGHT_EFFECT_BREATHE_CENTER`    |`1.85`       |Used to calculate the curve for the breathing animation. Valid values are 1.0 to 2.7 |
+|`RGBLIGHT_EFFECT_BREATHE_MAX`       |`255`        |The maximum brightness for the breathing mode. Valid values are 1 to 255             |
+|`RGBLIGHT_EFFECT_SNAKE_LENGTH`      |`4`          |The number of LEDs to light up for the "Snake" animation                             |
+|`RGBLIGHT_EFFECT_KNIGHT_LENGTH`     |`3`          |The number of LEDs to light up for the "Knight" animation                            |
+|`RGBLIGHT_EFFECT_KNIGHT_OFFSET`     |`0`          |The number of LEDs to start the "Knight" animation from the start of the strip by    |
+|`RGBLIGHT_EFFECT_KNIGHT_LED_NUM`    |`RGBLED_NUM` |The number of LEDs to have the "Knight" animation travel                             |
+|`RGBLIGHT_EFFECT_CHRISTMAS_INTERVAL`|`1000`       |How long to wait between light changes for the "Christmas" animation, in milliseconds|
+|`RGBLIGHT_EFFECT_CHRISTMAS_STEP`    |`2`          |The number of LEDs to group the red/green colors by for the "Christmas" animation    |
+
+You can also modify the speeds that the different modes animate at:
+
+```c
+// How long (in milliseconds) to wait between animation steps for each of the "Solid color breathing" animations
+const uint8_t RGBLED_BREATHING_INTERVALS[] PROGMEM = {30, 20, 10, 5};
+
+// How long (in milliseconds) to wait between animation steps for each of the "Cycling rainbow" animations
+const uint8_t RGBLED_RAINBOW_MOOD_INTERVALS[] PROGMEM = {120, 60, 30};
+
+// How long (in milliseconds) to wait between animation steps for each of the "Swirling rainbow" animations
+const uint8_t RGBLED_RAINBOW_SWIRL_INTERVALS[] PROGMEM = {100, 50, 20};
+
+// How long (in milliseconds) to wait between animation steps for each of the "Snake" animations
+const uint8_t RGBLED_SNAKE_INTERVALS[] PROGMEM = {100, 50, 20};
+
+// How long (in milliseconds) to wait between animation steps for each of the "Knight" animations
+const uint8_t RGBLED_KNIGHT_INTERVALS[] PROGMEM = {127, 63, 31};
+
+// These control which hues are selected for each of the "Static gradient" modes
+const uint16_t RGBLED_GRADIENT_RANGES[] PROGMEM = {360, 240, 180, 120, 90};
+```
+
+## Functions
+
+If you need to change your RGB lighting in code, for example in a macro to change the color whenever you switch layers, QMK provides a set of functions to assist you. See [`rgblight.h`](https://github.com/qmk/qmk_firmware/blob/master/quantum/rgblight.h) for the full list, but the most commonly used functions include:
+
+|Function                           |Description                                                                                                                                                            |
+|-----------------------------------|-----------------------------------------------------------------------------------------------------------------------------------------------------------------------|
+|`rgblight_enable()`                |Turn LEDs on, based on their previous state                                                                                                                            |
+|`rgblight_enable_noeeprom()`       |Turn LEDs on, based on their previous state (not written to EEPROM)                                                                                                    |
+|`rgblight_disable()`               |Turn LEDs off                                                                                                                                                          |
+|`rgblight_disable_noeeprom()`      |Turn LEDs off (not written to EEPROM)                                                                                                                                  |
+|`rgblight_mode(x)`                 |Set the mode, if RGB animations are enabled                                                                                                                            |
+|`rgblight_mode_noeeprom(x)`        |Set the mode, if RGB animations are enabled (not written to EEPROM)                                                                                                    |
+|`rgblight_setrgb(r, g, b)`         |Set all LEDs to the given RGB value where `r`/`g`/`b` are between 0 and 255 (not written to EEPROM)                                                                    |
+|`rgblight_setrgb_at(r, g, b, led)` |Set a single LED to the given RGB value, where `r`/`g`/`b` are between 0 and 255 and `led` is between 0 and `RGBLED_NUM` (not written to EEPROM)                       |
+|`rgblight_sethsv(h, s, v)`         |Set all LEDs to the given HSV value where `h` is between 0 and 360 and `s`/`v` are between 0 and 255                                                                   |
+|`rgblight_sethsv_noeeprom(h, s, v)`|Set all LEDs to the given HSV value where `h` is between 0 and 360 and `s`/`v` are between 0 and 255 (not written to EEPROM)                                           |
+|`rgblight_sethsv_at(h, s, v, led)` |Set a single LED to the given HSV value, where `h` is between 0 and 360, `s`/`v` are between 0 and 255, and `led` is between 0 and `RGBLED_NUM` (not written to EEPROM)|
+
+Additionally, [`rgblight_list.h`](https://github.com/qmk/qmk_firmware/blob/master/quantum/rgblight_list.h) defines several predefined shortcuts for various colors. Feel free to add to this list!
 
 ## Hardware Modification
 
-![Planck with RGB Underglow](https://raw.githubusercontent.com/qmk/qmk_firmware/3774a7fcdab5544fc787f4c200be05fcd417e31f/keyboards/planck/keymaps/yang/planck-with-rgb-underglow.jpg)
-
-Here is a quick demo on Youtube (with NPKC KC60) (https://www.youtube.com/watch?v=VKrpPAHlisY).
-
-For this mod, you need an unused pin wiring to DI of WS2812 strip. After wiring the VCC, GND, and DI, you can enable the underglow in your Makefile.
-
-    RGBLIGHT_ENABLE = yes
-
-In order to use the underglow animation functions, you need to have `#define RGBLIGHT_ANIMATIONS` in your `config.h`.
-
-Please add the following options into your config.h, and set them up according your hardware configuration. These settings are for the `F4` pin by default:
-
-    #define RGB_DI_PIN F4     // The pin your RGB strip is wired to
-    #define RGBLED_NUM 14     // Number of LEDs
-
-You'll need to edit `RGB_DI_PIN` to the pin you have your `DI` on your RGB strip wired to.
+If your keyboard lacks onboard underglow LEDs, you may often be able to solder on an RGB LED strip yourself. You will need to find an unused pin to wire to the data pin of your LED strip. Some keyboards may break out unused pins from the MCU to make soldering easier. The other two pins, VCC and GND, must also be connected to the appropriate power pins.

docs/feature_space_cadet.md

@@ -1,24 +0,0 @@
-## Space Cadet Shift: The Future, Built In
-
-Steve Losh [described](http://stevelosh.com/blog/2012/10/a-modern-space-cadet/) the Space Cadet Shift quite well. Essentially, you hit the left Shift on its own, and you get an opening parenthesis; hit the right Shift on its own, and you get the closing one. When hit with other keys, the Shift key keeps working as it always does. Yes, it's as cool as it sounds.
-
-To use it, use `KC_LSPO` (Left Shift, Parenthesis Open) for your left Shift on your keymap, and `KC_RSPC` (Right Shift, Parenthesis Close) for your right Shift.
-
-It's defaulted to work on US keyboards, but if your layout uses different keys for parenthesis, you can define those in your `config.h` like this:
-
-    #define LSPO_KEY KC_9
-    #define RSPC_KEY KC_0
-
-You can also choose between different rollover behaviors of the shift keys by defining:
-
-    #define DISABLE_SPACE_CADET_ROLLOVER
-
-in your `config.h`. Disabling rollover allows you to use the opposite shift key to cancel the space cadet state in the event of an erroneous press instead of emitting a pair of parentheses when the keys are released.
-
-The only other thing you're going to want to do is create a `Makefile` in your keymap directory and set the following:
-
-```
-COMMAND_ENABLE   = no  # Commands for debug and configuration
-```
-
-This is just to keep the keyboard from going into command mode when you hold both Shift keys at the same time.

docs/feature_space_cadet_shift.md

@@ -0,0 +1,33 @@
+# Space Cadet Shift: The Future, Built In
+
+Steve Losh described the [Space Cadet Shift](http://stevelosh.com/blog/2012/10/a-modern-space-cadet/) quite well. Essentially, when you tap Left Shift on its own, you get an opening parenthesis; tap Right Shift on its own and you get the closing one. When held, the Shift keys function as normal. Yes, it's as cool as it sounds.
+
+## Usage
+
+Replace the Left Shift key in your keymap with `KC_LSPO` (Left Shift, Parenthesis Open), and Right Shift with `KC_RSPC` (Right Shift, Parenthesis Close).
+
+## Keycodes
+
+|Keycode  |Description                           |
+|---------|--------------------------------------|
+|`KC_LSPO`|Left Shift when held, `(` when tapped |
+|`KC_RSPC`|Right Shift when held, `)` when tapped|
+
+## Caveats
+
+Space Cadet's functionality can conflict with the default Command functionality when both Shift keys are held at the same time. Make sure that Command is disabled in your `rules.mk` with:
+
+```make
+COMMAND_ENABLE = no
+```
+
+## Configuration
+
+By default Space Cadet assumes a US ANSI layout, but if your layout uses different keys for parentheses, you can redefine them in your `config.h`.
+You can also disable the rollover, allowing you to use the opposite Shift key to cancel the Space Cadet state in the event of an erroneous press, instead of emitting a pair of parentheses when the keys are released.
+
+|Define                        |Default      |Description                                                 |
+|------------------------------|-------------|------------------------------------------------------------|
+|`LSPO_KEY`                    |`KC_9`       |The keycode to send when Left Shift is tapped               |
+|`RSPC_KEY`                    |`KC_0`       |The keycode to send when Right Shift is tapped              |
+|`DISABLE_SPACE_CADET_ROLLOVER`|*Not defined*|If defined, use the opposite Shift key to cancel Space Cadet|

docs/feature_space_cadet_shift_enter.md

@@ -0,0 +1,31 @@
+# Space Cadet Shift Enter
+
+Based on the [Space Cadet Shift](feature_space_cadet_shift.md) feature. Tap the Shift key on its own, and it behaves like Enter. When held, the Shift functions as normal.
+
+## Usage
+
+Replace any Shift key in your keymap with `KC_SFTENT` (Shift, Enter), and you're done.
+
+## Keycodes
+
+|Keycode    |Description                             |
+|-----------|----------------------------------------|
+|`KC_SFTENT`|Right Shift when held, Enter when tapped|
+
+## Caveats
+
+As with Space Cadet Shift, this feature may conflict with Command, so it should be disabled in your `rules.mk` with:
+
+```make
+COMMAND_ENABLE = no
+```
+
+This feature also uses the same timers as Space Cadet Shift, so using them in tandem may produce strange results.
+
+## Configuration
+
+By default Space Cadet assumes a US ANSI layout, but if you'd like to use a different key for Enter, you can redefine it in your `config.h`:
+
+|Define      |Default |Description                                     |
+|------------|--------|------------------------------------------------|
+|`SFTENT_KEY`|`KC_ENT`|The keycode to send when the Shift key is tapped|

docs/feature_space_shift_cadet.md

@@ -1,26 +0,0 @@
-## Space Cadet Shift Enter: The future, built in
-
-Based on the Space Cadet Shift by Steve Losh [described](http://stevelosh.com/blog/2012/10/a-modern-space-cadet/) 
-Essentially, you hit the Shift on its own, and it acts as the enter key. When hit with other keys, the Shift key keeps working as it always does. Yes, it's as cool as it sounds. This solution works better than using a macro since the timers defined in quantum allow us to tell when another key is pressed, rather than just having a janky timer than results in accidental endlines. 
-
-To use it, use `KC_SFTENT` (Shift, Enter) for any Shift on your keymap.
-
-It's defaulted to work on US keyboards, but if you'd like to use a different key for Enter, you can define those in your `config.h` like this:
-
-    #define SFTENT_KEY KC_ENT
-
-
-The only other thing you're going to want to do is create a `rules.mk` in your keymap directory and set the following:
-
-```
-COMMAND_ENABLE   = no  # Commands for debug and configuration
-```
-
-This is just to keep the keyboard from going into command mode when you hold both Shift keys at the same time.
-
-
-
-
-
-PLEASE NOTE: this feature uses the same timers as the Space Cadet Shift feature, so using them in tandem may produce unwanted results. 
-

docs/feature_swap_hands.md

@@ -22,9 +22,9 @@ Note that the array indices are reversed same as the matrix and the values are o
 |Key        |Description                                                              |
 |-----------|-------------------------------------------------------------------------|
 |`SH_T(key)`|Sends `key` with a tap; momentary swap when held.                        |
-|`SW_ON`    |Turns on swapping and leaves it on.                                      |
-|`SW_OFF`   |Turn off swapping and leaves it off. Good for returning to a known state.|
-|`SW_MON`   |Swaps hands when pressed, returns to normal when released (momentary).   |
-|`SW_MOFF`  |Momentarily turns off swap.                                              |
+|`SH_ON`    |Turns on swapping and leaves it on.                                      |
+|`SH_OFF`   |Turn off swapping and leaves it off. Good for returning to a known state.|
+|`SH_MON`   |Swaps hands when pressed, returns to normal when released (momentary).   |
+|`SH_MOFF`  |Momentarily turns off swap.                                              |
 |`SH_TG`    |Toggles swap on and off with every key press.                            |
 |`SH_TT`    |Toggles with a tap; momentary when held.                                 |

docs/feature_tap_dance.md

@@ -196,22 +196,20 @@ SRC += your_name.c
 Pretty simple. It is a nice way to keep some rules common on all your keymaps.
 
 
-### In `/qmk_firmware/users/<your_name>/<you_name>.h`
+### In `/qmk_firmware/users/<your_name>/<your_name>.h`
 
 You will need a few things in this file:
 
 ```c
-#ifndef YOUR_NAME
-#define YOUR_NAME
+#pragma once
 
 #include "quantum.h"
 #include "process_keycode/process_tap_dance.h"
 
-
 typedef struct {
   bool is_press_action;
   int state;
-} xtap;
+} tap;
 
 enum {
   SINGLE_TAP = 1,
@@ -225,9 +223,9 @@ enum {
 
 //Tap dance enums
 enum {
-    CTL_X = 0,
-    SOME_OTHER_DANCE
-}
+  X_CTL = 0,
+  SOME_OTHER_DANCE
+};
 
 int cur_dance (qk_tap_dance_state_t *state);
 
@@ -241,7 +239,7 @@ void x_reset (qk_tap_dance_state_t *state, void *user_data);
 And then in your user's `.c` file you implement the functions above:
 
 ```c
-#include "gordon.h"
+#include "<your_name>.h"
 #include "quantum.h"
 #include "action.h"
 #include "process_keycode/process_tap_dance.h"
@@ -335,4 +333,4 @@ qk_tap_dance_action_t tap_dance_actions[] = {
 };
 ```
 
-And then simply use TD(X_CTL) anywhere in your keymap.
+And then simply use `TD(X_CTL)` anywhere in your keymap after including `<your_name>.h`.

docs/features.md

@@ -3,7 +3,7 @@
 QMK has a staggering number of features for building your keyboard. It can take some time to understand all of them and determine which one will achieve your goal.
 
 
-* [Advanced Keycodes](feature_advanced_keycodes.md) - Change layers, type shifted keys, and more. Go beyond typing simple characters.
+* [Advanced Keycodes](feature_advanced_keycodes.md) - Change layers, dual-action keys, and more. Go beyond typing simple characters.
 * [Audio](feature_audio.md) - Connect a speaker to your keyboard for audio feedback, midi support, and music mode.
 * [Auto Shift](feature_auto_shift.md) - Tap for the normal key, hold slightly longer for its shifted state.
 * [Backlight](feature_backlight.md) - LED lighting support for your keyboard.
@@ -19,7 +19,7 @@ QMK has a staggering number of features for building your keyboard. It can take
 * [PS2 Mouse](feature_ps2_mouse.md) - Driver for connecting a PS/2 mouse directly to your keyboard.
 * [RGB Light](feature_rgblight.md) - RGB lighting for your keyboard.
 * [RGB Matrix](feature_rgb_matrix.md) - RGB Matrix lights for per key lighting.
-* [Space Cadet](feature_space_cadet.md) - Use your left/right shift keys to type parenthesis and brackets.
+* [Space Cadet](feature_space_cadet_shift.md) - Use your left/right shift keys to type parenthesis and brackets.
 * [Stenography](feature_stenography.md) - Put your keyboard into Plover mode for stenography use.
 * [Swap Hands](feature_swap_hands.md) - Mirror your keyboard for one handed usage.
 * [Tap Dance](feature_tap_dance.md) - Make a single key do as many things as you want.

docs/hardware_drivers.md

@@ -25,3 +25,7 @@ You can make use of uGFX within QMK to drive character and graphic LCD's, LED ar
 ## WS2812 (AVR Only)
 
 Support for WS2811/WS2812{a,b,c} LED's. For more information see the [RGB Light](feature_rgblight.md) page.
+
+## IS31FL3731 (AVR Only)
+
+Support for up to 2 drivers. Each driver impliments 2 charlieplex matrices to individually address LEDs using I2C. This allows up to 144 same color LEDs or 32 RGB LEDs. For more information on how to setup the driver see the [RGB Matrix](feature_rgb_matrix.md) page.

docs/isp_flashing_guide.md

@@ -19,58 +19,79 @@ If you're having trouble flashing/erasing your board, and running into cryptic e
     Memory write error, use debug for more info.
     commands.c:360: Error writing memory data. (err -4)
 
-You're likely going to need to ISP flash your board/device to get it working again. Luckily, this process is pretty straight-forward, provided you have any extra programmable keyboard, Arduino, or Teensy 2.0/Teensy 2.0++. There are also dedicated ISP flashers available for this, but most cost >$15, and it's assumed that if you are googling this error, this is the first you've heard about ISP flashing, and don't have one readily available (whereas you might have some other AVR board). __We'll be using a Teensy 2.0 with Windows 10 in this guide__ - if you are comfortable doing this on another system, please consider editing this guide and contributing those instructions!
+You're likely going to need to ISP flash your board/device to get it working again. Luckily, this process is pretty straight-forward, provided you have any extra programmable keyboard, Pro Micro, or Teensy 2.0/Teensy 2.0++. There are also dedicated ISP flashers available for this, but most cost >$15, and it's assumed that if you are googling this error, this is the first you've heard about ISP flashing, and don't have one readily available (whereas you might have some other AVR board). __We'll be using a Teensy 2.0 or Pro Micro with Windows 10 in this guide__ - if you are comfortable doing this on another system, please consider editing this guide and contributing those instructions!   
 
 ## Software Needed
 
-* [The Arduino IDE](https://www.arduino.cc/en/Main/Software)
-* [Teensyduino](https://www.pjrc.com/teensy/td_download.html) (if you're using a Teensy)
-* [WinAVR](http://www.ladyada.net/learn/avr/setup-win.html) (Windows)
+* [Teensy Loader](https://www.pjrc.com/teensy/loader.html) (if using a Teensy)
+* QMK Toolbox (flash as usual - be sure to select the correct MCU) or `avrdude` via [WinAVR](http://www.ladyada.net/learn/avr/setup-win.html) (for Teensy & Pro Micro)
 
 ## Wiring
 
 This is pretty straight-forward - we'll be connecting like-things to like-things in the following manner:
 
-    Flasher B0  <-> Keyboard RESET
-    Flasher B1  <-> Keyboard B1 (SCLK)
-    Flasher B2  <-> Keyboard B2 (MOSI)
-    Flasher B3  <-> Keyboard B3 (MISO)
-    Flasher VCC <-> Keyboard VCC
-    Flasher GND <-> Keyboard GND
+### Teensy 2.0
 
-## The ISP Firmware
+    Teensy B0  <-> Keyboard RESET
+    Teensy B1  <-> Keyboard B1 (SCLK)
+    Teensy B2  <-> Keyboard B2 (MOSI)
+    Teensy B3  <-> Keyboard B3 (MISO)
+    Teensy VCC <-> Keyboard VCC
+    Teensy GND <-> Keyboard GND
+    
+### Pro Micro
+
+    Pro Micro 10 (B6)  <-> Keyboard RESET
+    Pro Micro 15 (B1)  <-> Keyboard B1 (SCLK)
+    Pro Micro 16 (B2)  <-> Keyboard B2 (MOSI)
+    Pro Micro 14 (B3)  <-> Keyboard B3 (MISO)
+    Pro Micro VCC      <-> Keyboard VCC
+    Pro Micro GND      <-> Keyboard GND
+
+## The ISP Firmware (now pre-compiled)
+
+The only difference between the .hex files below is which pin is connected to RESET. You can use them on other boards as well, as long as you're aware of the pins being used. If for some reason neither of these pins are available, [create an issue](https://github.com/qmk/qmk_firmware/issues/new), and we can generate one for you!
+
+* Teensy 2.0: [`util/teensy_2.0_ISP_B0.hex`](https://github.com/qmk/qmk_firmware/blob/master/util/teensy_2.0_ISP_B0.hex) (`B0`)
+* Pro Micro: [`util/pro_micro_ISP_B6_10.hex`](https://github.com/qmk/qmk_firmware/blob/master/util/pro_mico_ISP_B6_10.hex) (`B6/10`)
+
+**Flash your Teenys/Pro Micro with one of these and continue - you won't need the file after flashing your ISP device.**
+
+## Just the Bootloader File
+
+If you just want to get things back to normal, you can flash only a bootloader from [`util/` folder](https://github.com/qmk/qmk_firmware/tree/master/util), and use your normal process to flash the firmware afterwards. Be sure to flash the correct bootloader for your chip:
+
+* [`atmega32u4`](https://github.com/qmk/qmk_firmware/blob/master/util/bootloader_atmega32u4_1_0_0.hex) - Most keyboards, Planck Rev 1-5, Preonic Rev 1-2
+* [`at90usb1286`](https://github.com/qmk/qmk_firmware/blob/master/util/bootloader_at90usb128x_1_0_1.hex) - Planck Light Rev 1
+
+If you're not sure what your board uses, look in the `rules.mk` file for the keyboard in QMK. The `MCU =` line will have the value you need. It may differ between different versions of the board.
+
+### Advanced/Production Techniques
+
+If you'd like to flash both the bootloader **and** the regular firmware at the same time, you need to combine the files. 
+
+1. Open the original firmware .hex file in a text editor
+2. Remove the last line (which should be `:00000001FF` - this is an EOF message)
+3. Copy the entire bootloader's contents onto a new line (with no empty lines between) and paste it at the end of the original file
+4. Save it as a new file by naming it `<keyboard>_<keymap>_production.hex`
+
+It's possible to use other bootloaders here in the same way, but __you need a bootloader__, otherwise you'll have to use ISP again to write new firmware to your keyboard.
+
+## Flashing Your Bootloader/Production File
 
 Make sure your keyboard is unplugged from any device, and plug in your Teensy.
 
-1. Run Arduino after you have everything installed
-2. Select `Tools > Board * > Teensy 2.0`
-3. Click `File > Examples > 11.ArduinoISP > ArduinoISP`
+### QMK Toolbox
 
-Then scroll down until you see something that looks like this block of code:
+1. `AVRISP device connected` will show up in yellow
+2. Select the correct bootloader/production .hex file with the `Open` dialog (spaces can't be in the path)
+3. Be sure the correct `Microcontroller` option is selected
+4. Hit `Flash`
+5. Wait, as nothing will output for a while, especially with production files
 
-    // Configure which pins to use:
+If the verification and fuse checks are ok, you're done! Your board may restart automatically, otherwise, unplug your Teensy and plug in your keyboard - you can leave your Teensy wired to your keyboard while testing things, but it's recommended that you desolder it/remove the wiring once you're sure everything works.
 
-    // The standard pin configuration.
-    #ifndef ARDUINO_HOODLOADER2
-
-    #define RESET     0  // Use 0 (B0) instead of 10
-    #define LED_HB    11 // Use 11 (LED on the Teensy 2.0)
-    #define LED_ERR   8  // This won't be used unless you have an LED hooked-up to 8 (D3)
-    #define LED_PMODE 7  // This won't be used unless you have an LED hooked-up to 7 (D2)
-
-And make the changes in the last four lines. If you're using something besides the Teensy 2.0, you'll want to choose something else that makes sense for `LED_HB`. We define `RESET` as `0`/`B0` because that's what's close - if you want to use another pin for some reason, [you can use the pinouts to choose something else](https://www.pjrc.com/teensy/pinout.html).
-
-Once you've made your changes, you can click the Upload button (right arrow), which will open up the Teensy flasher app - you'll need to press the reset button on the Teensy the first time, but after that, it's automatic (you shouldn't be flashing this more than once, though). Once flashed, the orange LED on the Teensy will flash on and off, indicating it's ready for some action.
-
-## The `.hex` File
-
-Before flashing your firmware, you're going to need to and do a little preparation. We'll be appending [this bootloader (also a .hex file)](https://github.com/qmk/qmk_firmware/blob/master/util/bootloader_atmega32u4_1_0_0.hex) to the end of our firmware by opening the original .hex file in a text editor, and removing the last line, which should be `:00000001FF` (this is an EOF message). After that's been removed, copy the entire bootloader's contents and paste it at the end of the original file, and save it.
-
-It's possible to use other bootloaders here in the same way, but __you need a bootloader__, otherwise you'll have to ISP to write new firmware to your keyboard.
-
-## Flashing Your Firmware
-
-Make sure your keyboard is unplugged from any device, and plug in your Teensy.
+### Command Line
 
 Open `cmd` and navigate to your where your modified .hex file is. We'll pretend this file is called `main.hex`, and that your Teensy 2.0 is on the `COM3` port - if you're unsure, you can open your Device Manager, and look for `Ports > USB Serial Device`. Use that COM port here. You can confirm it's the right port with:
 

docs/keycodes.md

@@ -8,40 +8,8 @@ This is a reference only. Each group of keys links to the page documenting their
 
 |Key                    |Aliases             |Description                                    |
 |-----------------------|--------------------|-----------------------------------------------|
-|`KC_1`                 |                    |`1` and `!`                                    |
-|`KC_2`                 |                    |`2` and `@`                                    |
-|`KC_3`                 |                    |`3` and `#`                                    |
-|`KC_4`                 |                    |`4` and `$`                                    |
-|`KC_5`                 |                    |`5` and `%`                                    |
-|`KC_6`                 |                    |`6` and `^`                                    |
-|`KC_7`                 |                    |`7` and `&`                                    |
-|`KC_8`                 |                    |`8` and `*`                                    |
-|`KC_9`                 |                    |`9` and `(`                                    |
-|`KC_0`                 |                    |`0` and `)`                                    |
-|`KC_F1`                |                    |                                               |
-|`KC_F2`                |                    |                                               |
-|`KC_F3`                |                    |                                               |
-|`KC_F4`                |                    |                                               |
-|`KC_F5`                |                    |                                               |
-|`KC_F6`                |                    |                                               |
-|`KC_F7`                |                    |                                               |
-|`KC_F8`                |                    |                                               |
-|`KC_F9`                |                    |                                               |
-|`KC_F10`               |                    |                                               |
-|`KC_F11`               |                    |                                               |
-|`KC_F12`               |                    |                                               |
-|`KC_F13`               |                    |                                               |
-|`KC_F14`               |                    |                                               |
-|`KC_F15`               |                    |                                               |
-|`KC_F16`               |                    |                                               |
-|`KC_F17`               |                    |                                               |
-|`KC_F18`               |                    |                                               |
-|`KC_F19`               |                    |                                               |
-|`KC_F20`               |                    |                                               |
-|`KC_F21`               |                    |                                               |
-|`KC_F22`               |                    |                                               |
-|`KC_F23`               |                    |                                               |
-|`KC_F24`               |                    |                                               |
+|`KC_NO`                |`XXXXXXX`           |Ignore this key (NOOP)                         |
+|`KC_TRANSPARENT`       |`KC_TRNS`, `_______`|Use the next lowest non-transparent key        |
 |`KC_A`                 |                    |`a` and `A`                                    |
 |`KC_B`                 |                    |`b` and `B`                                    |
 |`KC_C`                 |                    |`c` and `C`                                    |
@@ -68,6 +36,16 @@ This is a reference only. Each group of keys links to the page documenting their
 |`KC_X`                 |                    |`x` and `X`                                    |
 |`KC_Y`                 |                    |`y` and `Y`                                    |
 |`KC_Z`                 |                    |`z` and `Z`                                    |
+|`KC_1`                 |                    |`1` and `!`                                    |
+|`KC_2`                 |                    |`2` and `@`                                    |
+|`KC_3`                 |                    |`3` and `#`                                    |
+|`KC_4`                 |                    |`4` and `$`                                    |
+|`KC_5`                 |                    |`5` and `%`                                    |
+|`KC_6`                 |                    |`6` and `^`                                    |
+|`KC_7`                 |                    |`7` and `&`                                    |
+|`KC_8`                 |                    |`8` and `*`                                    |
+|`KC_9`                 |                    |`9` and `(`                                    |
+|`KC_0`                 |                    |`0` and `)`                                    |
 |`KC_ENTER`             |`KC_ENT`            |Return (Enter)                                 |
 |`KC_ESCAPE`            |`KC_ESC`            |Escape                                         |
 |`KC_BSPACE`            |`KC_BSPC`           |Delete (Backspace)                             |
@@ -79,33 +57,28 @@ This is a reference only. Each group of keys links to the page documenting their
 |`KC_RBRACKET`          |`KC_RBRC`           |`]` and `}`                                    |
 |`KC_BSLASH`            |`KC_BSLS`           |`\` and <code>&#124;</code>                    |
 |`KC_NONUS_HASH`        |`KC_NUHS`           |Non-US `#` and `~`                             |
-|`KC_NONUS_BSLASH`      |`KC_NUBS`           |Non-US `\` and <code>&#124;</code>             |
-|`KC_INT1`              |`KC_RO`             |JIS `\` and <code>&#124;</code>                |
-|`KC_INT2`              |`KC_KANA`           |JIS Katakana/Hiragana                          |
-|`KC_INT3`              |`KC_JYEN`           |JIS `¥`                                        |
 |`KC_SCOLON`            |`KC_SCLN`           |`;` and `:`                                    |
 |`KC_QUOTE`             |`KC_QUOT`           |`'` and `"`                                    |
-|`KC_GRAVE`             |`KC_GRV`            |<code>&#96;</code> and `~`                     |
+|`KC_GRAVE`             |`KC_GRV`, `KC_ZKHK` |<code>&#96;</code> and `~`, JIS Zenkaku/Hankaku|
 |`KC_COMMA`             |`KC_COMM`           |`,` and `<`                                    |
 |`KC_DOT`               |                    |`.` and `>`                                    |
 |`KC_SLASH`             |`KC_SLSH`           |`/` and `?`                                    |
-|`KC_CAPSLOCK`          |`KC_CAPS`           |Caps Lock                                      |
-|`KC_LCTRL`             |`KC_LCTL`           |Left Control                                   |
-|`KC_LSHIFT`            |`KC_LSFT`           |Left Shift                                     |
-|`KC_LALT`              |                    |Left Alt                                       |
-|`KC_LGUI`              |`KC_LCMD`, `KC_LWIN`|Left GUI (Windows/Command/Meta key)            |
-|`KC_RCTRL`             |`KC_RCTL`           |Right Control                                  |
-|`KC_RSHIFT`            |`KC_RSFT`           |Right Shift                                    |
-|`KC_RALT`              |                    |Right Alt                                      |
-|`KC_RGUI`              |`KC_RCMD`, `KC_RWIN`|Right GUI (Windows/Command/Meta key)           |
-|`KC_LOCKING_CAPS`      |`KC_LCAP`           |Locking Caps Lock                              |
-|`KC_LOCKING_NUM`       |`KC_LNUM`           |Locking Num Lock                               |
-|`KC_LOCKING_SCROLL`    |`KC_LSCR`           |Locking Scroll Lock                            |
-|`KC_INT4`              |`KC_HENK`           |JIS Henkan                                     |
-|`KC_INT5`              |`KC_MHEN`           |JIS Muhenkan                                   |
+|`KC_CAPSLOCK`          |`KC_CLCK`, `KC_CAPS`|Caps Lock                                      |
+|`KC_F1`                |                    |F1                                             |
+|`KC_F2`                |                    |F2                                             |
+|`KC_F3`                |                    |F3                                             |
+|`KC_F4`                |                    |F4                                             |
+|`KC_F5`                |                    |F5                                             |
+|`KC_F6`                |                    |F6                                             |
+|`KC_F7`                |                    |F7                                             |
+|`KC_F8`                |                    |F8                                             |
+|`KC_F9`                |                    |F9                                             |
+|`KC_F10`               |                    |F10                                            |
+|`KC_F11`               |                    |F11                                            |
+|`KC_F12`               |                    |F12                                            |
 |`KC_PSCREEN`           |`KC_PSCR`           |Print Screen                                   |
 |`KC_SCROLLLOCK`        |`KC_SLCK`           |Scroll Lock                                    |
-|`KC_PAUSE`             |`KC_PAUS`           |Pause                                          |
+|`KC_PAUSE`             |`KC_PAUS`, `KC_BRK` |Pause                                          |
 |`KC_INSERT`            |`KC_INS`            |Insert                                         |
 |`KC_HOME`              |                    |Home                                           |
 |`KC_PGUP`              |                    |Page Up                                        |
@@ -116,58 +89,6 @@ This is a reference only. Each group of keys links to the page documenting their
 |`KC_LEFT`              |                    |Left Arrow                                     |
 |`KC_DOWN`              |                    |Down Arrow                                     |
 |`KC_UP`                |                    |Up Arrow                                       |
-|`KC_APPLICATION`       |`KC_APP`            |Application (Windows Menu Key)                 |
-|`KC_POWER`             |                    |Deprecated by MS in favor of `KC_SYSTEM_POWER`.|
-|`KC_EXECUTE`           |                    |Execute                                        |
-|`KC_HELP`              |                    |Help                                           |
-|`KC_MENU`              |                    |Menu                                           |
-|`KC_SELECT`            |                    |Select                                         |
-|`KC_AGAIN`             |                    |Again                                          |
-|`KC_UNDO`              |                    |Undo                                           |
-|`KC_CUT`               |                    |Cut                                            |
-|`KC_COPY`              |                    |Copy                                           |
-|`KC_PASTE`             |                    |Paste                                          |
-|`KC_FIND`              |                    |Find                                           |
-|`KC_ALT_ERASE`         |                    |Alternate Erase                                |
-|`KC_SYSREQ`            |                    |SysReq/Attention                               |
-|`KC_CANCEL`            |                    |Cancel                                         |
-|`KC_CLEAR`             |                    |Clear                                          |
-|`KC_PRIOR`             |                    |Prior                                          |
-|`KC_RETURN`            |                    |Return                                         |
-|`KC_SEPARATOR`         |                    |Separator                                      |
-|`KC_OUT`               |                    |Out                                            |
-|`KC_OPER`              |                    |Oper                                           |
-|`KC_CLEAR_AGAIN`       |                    |Clear/Again                                    |
-|`KC_CRSEL`             |                    |CrSel/Props                                    |
-|`KC_EXSEL`             |                    |ExSel                                          |
-|`KC_SYSTEM_POWER`      |`KC_PWR`            |System Power Down. Recommended over `KC_POWER`.|
-|`KC_SYSTEM_SLEEP`      |`KC_SLEP`           |System Sleep                                   |
-|`KC_SYSTEM_WAKE`       |`KC_WAKE`           |System Wake                                    |
-|`KC_MAIL`              |`KC_MAIL`           |                                               |
-|`KC_CALCULATOR`        |`KC_CALC`           |                                               |
-|`KC_MY_COMPUTER`       |`KC_MYCM`           |                                               |
-|`KC_WWW_SEARCH`        |`KC_WSCH`           |                                               |
-|`KC_WWW_HOME`          |`KC_WHOM`           |                                               |
-|`KC_WWW_BACK`          |`KC_WBAK`           |                                               |
-|`KC_WWW_FORWARD`       |`KC_WFWD`           |                                               |
-|`KC_WWW_STOP`          |`KC_WSTP`           |                                               |
-|`KC_WWW_REFRESH`       |`KC_WREF`           |                                               |
-|`KC_WWW_FAVORITES`     |`KC_WFAV`           |                                               |
-|`KC_STOP`              |                    |Stop                                           |
-|`KC__MUTE`             |                    |Mute (macOS)                                   |
-|`KC__VOLUP`            |                    |Volume Up (macOS)                              |
-|`KC__VOLDOWN`          |                    |Volume Down (macOS)                            |
-|`KC_AUDIO_MUTE`        |`KC_MUTE`           |Mute (Windows/macOS/Linux)                     |
-|`KC_AUDIO_VOL_UP`      |`KC_VOLU`           |Volume Up (Windows/macOS/Linux)                |
-|`KC_AUDIO_VOL_DOWN`    |`KC_VOLD`           |Volume Down (Windows/macOS/Linux)              |
-|`KC_MEDIA_NEXT_TRACK`  |`KC_MNXT`           |Next Track (Windows)                           |
-|`KC_MEDIA_PREV_TRACK`  |`KC_MPRV`           |Previous Track (Windows)                       |
-|`KC_MEDIA_FAST_FORWARD`|`KC_MFFD`           |Next Track (macOS)                             |
-|`KC_MEDIA_REWIND`      |`KC_MRWD`           |Previous Track (macOS)                         |
-|`KC_MEDIA_STOP`        |`KC_MSTP`           |Stop Track                                     |
-|`KC_MEDIA_PLAY_PAUSE`  |`KC_MPLY`           |Play/Pause Track                               |
-|`KC_MEDIA_SELECT`      |`KC_MSEL`           |                                               |
-|`KC_MEDIA_EJECT`       |`KC_EJCT`           |Eject (macOS)                                  |
 |`KC_NUMLOCK`           |`KC_NLCK`           |Keypad Num Lock and Clear                      |
 |`KC_KP_SLASH`          |`KC_PSLS`           |Keypad `/`                                     |
 |`KC_KP_ASTERISK`       |`KC_PAST`           |Keypad `*`                                     |
@@ -185,11 +106,103 @@ This is a reference only. Each group of keys links to the page documenting their
 |`KC_KP_9`              |`KC_P9`             |Keypad `9` and Page Up                         |
 |`KC_KP_0`              |`KC_P0`             |Keypad `0` and Insert                          |
 |`KC_KP_DOT`            |`KC_PDOT`           |Keypad `.` and Delete                          |
+|`KC_NONUS_BSLASH`      |`KC_NUBS`           |Non-US `\` and <code>&#124;</code>             |
+|`KC_APPLICATION`       |`KC_APP`            |Application (Windows Menu Key)                 |
+|`KC_POWER`             |                    |System Power (macOS)                           |
 |`KC_KP_EQUAL`          |`KC_PEQL`           |Keypad `=`                                     |
+|`KC_F13`               |                    |F13                                            |
+|`KC_F14`               |                    |F14                                            |
+|`KC_F15`               |                    |F15                                            |
+|`KC_F16`               |                    |F16                                            |
+|`KC_F17`               |                    |F17                                            |
+|`KC_F18`               |                    |F18                                            |
+|`KC_F19`               |                    |F19                                            |
+|`KC_F20`               |                    |F20                                            |
+|`KC_F21`               |                    |F21                                            |
+|`KC_F22`               |                    |F22                                            |
+|`KC_F23`               |                    |F23                                            |
+|`KC_F24`               |                    |F24                                            |
+|`KC_EXECUTE`           |`KC_EXEC`           |Execute                                        |
+|`KC_HELP`              |                    |Help                                           |
+|`KC_MENU`              |                    |Menu                                           |
+|`KC_SELECT`            |`KC_SLCT`           |Select                                         |
+|`KC_STOP`              |                    |Stop                                           |
+|`KC_AGAIN`             |`KC_AGIN`           |Again                                          |
+|`KC_UNDO`              |                    |Undo                                           |
+|`KC_CUT`               |                    |Cut                                            |
+|`KC_COPY`              |                    |Copy                                           |
+|`KC_PASTE`             |`KC_PSTE`           |Paste                                          |
+|`KC_FIND`              |                    |Find                                           |
+|`KC__MUTE`             |                    |Mute (macOS)                                   |
+|`KC__VOLUP`            |                    |Volume Up (macOS)                              |
+|`KC__VOLDOWN`          |                    |Volume Down (macOS)                            |
+|`KC_LOCKING_CAPS`      |`KC_LCAP`           |Locking Caps Lock                              |
+|`KC_LOCKING_NUM`       |`KC_LNUM`           |Locking Num Lock                               |
+|`KC_LOCKING_SCROLL`    |`KC_LSCR`           |Locking Scroll Lock                            |
 |`KC_KP_COMMA`          |`KC_PCMM`           |Keypad `,`                                     |
 |`KC_KP_EQUAL_AS400`    |                    |Keypad `=` on AS/400 keyboards                 |
-|`KC_NO`                |                    |Ignore this key (NOOP)                         |
-|`KC_TRANSPARENT`       |`KC_TRNS`           |Use the next lowest non-transparent key        |
+|`KC_INT1`              |`KC_RO`             |JIS `\` and <code>&#124;</code>                |
+|`KC_INT2`              |`KC_KANA`           |JIS Katakana/Hiragana                          |
+|`KC_INT3`              |`KC_JYEN`           |JIS `¥`                                        |
+|`KC_INT4`              |`KC_HENK`           |JIS Henkan                                     |
+|`KC_INT5`              |`KC_MHEN`           |JIS Muhenkan                                   |
+|`KC_INT6`              |                    |JIS Numpad `,`                                 |
+|`KC_INT7`              |                    |International 7                                |
+|`KC_INT8`              |                    |International 8                                |
+|`KC_INT9`              |                    |International 9                                |
+|`KC_LANG1`             |`KC_HAEN`           |Hangul/English                                 |
+|`KC_LANG2`             |`KC_HANJ`           |Hanja                                          |
+|`KC_LANG3`             |                    |JIS Katakana                                   |
+|`KC_LANG4`             |                    |JIS Hiragana                                   |
+|`KC_LANG5`             |                    |JIS Zenkaku/Hankaku                            |
+|`KC_LANG6`             |                    |Language 6                                     |
+|`KC_LANG7`             |                    |Language 7                                     |
+|`KC_LANG8`             |                    |Language 8                                     |
+|`KC_LANG9`             |                    |Language 9                                     |
+|`KC_ALT_ERASE`         |`KC_ERAS`           |Alternate Erase                                |
+|`KC_SYSREQ`            |                    |SysReq/Attention                               |
+|`KC_CANCEL`            |                    |Cancel                                         |
+|`KC_CLEAR`             |`KC_CLR`            |Clear                                          |
+|`KC_PRIOR`             |                    |Prior                                          |
+|`KC_RETURN`            |                    |Return                                         |
+|`KC_SEPARATOR`         |                    |Separator                                      |
+|`KC_OUT`               |                    |Out                                            |
+|`KC_OPER`              |                    |Oper                                           |
+|`KC_CLEAR_AGAIN`       |                    |Clear/Again                                    |
+|`KC_CRSEL`             |                    |CrSel/Props                                    |
+|`KC_EXSEL`             |                    |ExSel                                          |
+|`KC_LCTRL`             |`KC_LCTL`           |Left Control                                   |
+|`KC_LSHIFT`            |`KC_LSFT`           |Left Shift                                     |
+|`KC_LALT`              |                    |Left Alt                                       |
+|`KC_LGUI`              |`KC_LCMD`, `KC_LWIN`|Left GUI (Windows/Command/Meta key)            |
+|`KC_RCTRL`             |`KC_RCTL`           |Right Control                                  |
+|`KC_RSHIFT`            |`KC_RSFT`           |Right Shift                                    |
+|`KC_RALT`              |                    |Right Alt                                      |
+|`KC_RGUI`              |`KC_RCMD`, `KC_RWIN`|Right GUI (Windows/Command/Meta key)           |
+|`KC_SYSTEM_POWER`      |`KC_PWR`            |System Power Down                              |
+|`KC_SYSTEM_SLEEP`      |`KC_SLEP`           |System Sleep                                   |
+|`KC_SYSTEM_WAKE`       |`KC_WAKE`           |System Wake                                    |
+|`KC_AUDIO_MUTE`        |`KC_MUTE`           |Mute                                           |
+|`KC_AUDIO_VOL_UP`      |`KC_VOLU`           |Volume Up                                      |
+|`KC_AUDIO_VOL_DOWN`    |`KC_VOLD`           |Volume Down                                    |
+|`KC_MEDIA_NEXT_TRACK`  |`KC_MNXT`           |Next Track (Windows)                           |
+|`KC_MEDIA_PREV_TRACK`  |`KC_MPRV`           |Previous Track (Windows)                       |
+|`KC_MEDIA_STOP`        |`KC_MSTP`           |Stop Track (Windows)                           |
+|`KC_MEDIA_PLAY_PAUSE`  |`KC_MPLY`           |Play/Pause Track                               |
+|`KC_MEDIA_SELECT`      |`KC_MSEL`           |Launch Media Player (Windows)                  |
+|`KC_MEDIA_EJECT`       |`KC_EJCT`           |Eject (macOS)                                  |
+|`KC_MAIL`              |                    |Launch Mail (Windows)                          |
+|`KC_CALCULATOR`        |`KC_CALC`           |Launch Calculator (Windows)                    |
+|`KC_MY_COMPUTER`       |`KC_MYCM`           |Launch My Computer (Windows)                   |
+|`KC_WWW_SEARCH`        |`KC_WSCH`           |Browser Search (Windows)                       |
+|`KC_WWW_HOME`          |`KC_WHOM`           |Browser Home (Windows)                         |
+|`KC_WWW_BACK`          |`KC_WBAK`           |Browser Back (Windows)                         |
+|`KC_WWW_FORWARD`       |`KC_WFWD`           |Browser Forward (Windows)                      |
+|`KC_WWW_STOP`          |`KC_WSTP`           |Browser Stop (Windows)                         |
+|`KC_WWW_REFRESH`       |`KC_WREF`           |Browser Refresh (Windows)                      |
+|`KC_WWW_FAVORITES`     |`KC_WFAV`           |Browser Favorites (Windows)                    |
+|`KC_MEDIA_FAST_FORWARD`|`KC_MFFD`           |Next Track (macOS)                             |
+|`KC_MEDIA_REWIND`      |`KC_MRWD`           |Previous Track (macOS)                         |
 
 ## [Quantum Keycodes](quantum_keycodes.md#qmk-keycodes)
 
@@ -269,7 +282,7 @@ This is a reference only. Each group of keys links to the page documenting their
 |`OUT_BT`  |Bluetooth only                                |
 
 
-## [Layer Switching](feature_advanced_keycodes.md# Switching and Toggling Layers)
+## [Layer Switching](feature_advanced_keycodes.md#switching-and-toggling-layers)
 
 |Key         |Description                                                               |
 |-----------------|---------------------------------------------------------------------|
@@ -389,31 +402,31 @@ This is a reference only. Each group of keys links to the page documenting their
 |`PRINT_ON` |Start printing everything the user types|
 |`PRINT_OFF`|Stop printing everything the user types |
 
-## [US ANSI Shifted Keys](keycodes_us_ansi_shifted.md)
+## [US ANSI Shifted Symbols](keycodes_us_ansi_shifted.md)
 
-|Key                     |Aliases           |Description        |
-|------------------------|------------------|-------------------|
-|`KC_TILDE`              |`KC_TILD`         |`~`                |
-|`KC_EXCLAIM`            |`KC_EXLM`         |`!`                |
-|`KC_AT`                 |                  |`@`                |
-|`KC_HASH`               |                  |`#`                |
-|`KC_DOLLAR`             |`KC_DLR`          |`$`                |
-|`KC_PERCENT`            |`KC_PERC`         |`%`                |
-|`KC_CIRCUMFLEX`         |`KC_CIRC`         |`^`                |
-|`KC_AMPERSAND`          |`KC_AMPR`         |`&`                |
-|`KC_ASTERISK`           |`KC_ASTR`         |`*`                |
-|`KC_LEFT_PAREN`         |`KC_LPRN`         |`(`                |
-|`KC_RIGHT_PAREN`        |`KC_RPRN`         |`)`                |
-|`KC_UNDERSCORE`         |`KC_UNDS`         |`_`                |
-|`KC_PLUS`               |                  |`+`                |
-|`KC_LEFT_CURLY_BRACE`   |`KC_LCBR`         |`{`                |
-|`KC_RIGHT_CURLY_BRACE`  |`KC_RCBR`         |`}`                |
-|`KC_PIPE`               |                  |<code>&#124;</code>|
-|`KC_COLON`              |`KC_COLN`         |`:`                |
-|`KC_DOUBLE_QUOTE`       |`KC_DQT`/`KC_DQUO`|`"`                |
-|`KC_LEFT_ANGLE_BRACKET` |`KC_LT`/`KC_LABK` |`<`                |
-|`KC_RIGHT_ANGLE_BRACKET`|`KC_GT`/`KC_RABK` |`>`                |
-|`KC_QUESTION`           |`KC_QUES`         |`?`                |
+|Key                     |Aliases            |Description        |
+|------------------------|-------------------|-------------------|
+|`KC_TILDE`              |`KC_TILD`          |`~`                |
+|`KC_EXCLAIM`            |`KC_EXLM`          |`!`                |
+|`KC_AT`                 |                   |`@`                |
+|`KC_HASH`               |                   |`#`                |
+|`KC_DOLLAR`             |`KC_DLR`           |`$`                |
+|`KC_PERCENT`            |`KC_PERC`          |`%`                |
+|`KC_CIRCUMFLEX`         |`KC_CIRC`          |`^`                |
+|`KC_AMPERSAND`          |`KC_AMPR`          |`&`                |
+|`KC_ASTERISK`           |`KC_ASTR`          |`*`                |
+|`KC_LEFT_PAREN`         |`KC_LPRN`          |`(`                |
+|`KC_RIGHT_PAREN`        |`KC_RPRN`          |`)`                |
+|`KC_UNDERSCORE`         |`KC_UNDS`          |`_`                |
+|`KC_PLUS`               |                   |`+`                |
+|`KC_LEFT_CURLY_BRACE`   |`KC_LCBR`          |`{`                |
+|`KC_RIGHT_CURLY_BRACE`  |`KC_RCBR`          |`}`                |
+|`KC_PIPE`               |                   |<code>&#124;</code>|
+|`KC_COLON`              |`KC_COLN`          |`:`                |
+|`KC_DOUBLE_QUOTE`       |`KC_DQUO`, `KC_DQT`|`"`                |
+|`KC_LEFT_ANGLE_BRACKET` |`KC_LABK`, `KC_LT` |`<`                |
+|`KC_RIGHT_ANGLE_BRACKET`|`KC_RABK`, `KC_GT` |`>`                |
+|`KC_QUESTION`           |`KC_QUES`          |`?`                |
 
 ## [Switching and Toggling Layers](feature_advanced_keycodes.md#switching-and-toggling-layers)
 

docs/keycodes_basic.md

@@ -47,117 +47,145 @@ The basic set of keycodes are based on the [HID Keyboard/Keypad Usage Page (0x07
 
 |Key     |Description|
 |--------|-----------|
-|`KC_F1` |           |
-|`KC_F2` |           |
-|`KC_F3` |           |
-|`KC_F4` |           |
-|`KC_F5` |           |
-|`KC_F6` |           |
-|`KC_F7` |           |
-|`KC_F8` |           |
-|`KC_F9` |           |
-|`KC_F10`|           |
-|`KC_F11`|           |
-|`KC_F12`|           |
-|`KC_F13`|           |
-|`KC_F14`|           |
-|`KC_F15`|           |
-|`KC_F16`|           |
-|`KC_F17`|           |
-|`KC_F18`|           |
-|`KC_F19`|           |
-|`KC_F20`|           |
-|`KC_F21`|           |
-|`KC_F22`|           |
-|`KC_F23`|           |
-|`KC_F24`|           |
+|`KC_F1` |F1         |
+|`KC_F2` |F2         |
+|`KC_F3` |F3         |
+|`KC_F4` |F4         |
+|`KC_F5` |F5         |
+|`KC_F6` |F6         |
+|`KC_F7` |F7         |
+|`KC_F8` |F8         |
+|`KC_F9` |F9         |
+|`KC_F10`|F10        |
+|`KC_F11`|F11        |
+|`KC_F12`|F12        |
+|`KC_F13`|F13        |
+|`KC_F14`|F14        |
+|`KC_F15`|F15        |
+|`KC_F16`|F16        |
+|`KC_F17`|F17        |
+|`KC_F18`|F18        |
+|`KC_F19`|F19        |
+|`KC_F20`|F20        |
+|`KC_F21`|F21        |
+|`KC_F22`|F22        |
+|`KC_F23`|F23        |
+|`KC_F24`|F24        |
 
 ## Punctuation
 
-|Key              |Aliases  |Description                       |
-|-----------------|---------|----------------------------------|
-|`KC_ENTER`       |`KC_ENT` |Return (Enter)                    |
-|`KC_ESCAPE`      |`KC_ESC` |Escape                            |
-|`KC_BSPACE`      |`KC_BSPC`|Delete (Backspace)                |
-|`KC_TAB`         |         |Tab                               |
-|`KC_SPACE`       |`KC_SPC` |Spacebar                          |
-|`KC_MINUS`       |`KC_MINS`|`-` and `_`                       |
-|`KC_EQUAL`       |`KC_EQL` |`=` and `+`                       |
-|`KC_LBRACKET`    |`KC_LBRC`|`[` and `{`                       |
-|`KC_RBRACKET`    |`KC_RBRC`|`]` and `}`                       |
-|`KC_BSLASH`      |`KC_BSLS`|`\` and <code>&#124;</code>       |
-|`KC_NONUS_HASH`  |`KC_NUHS`|Non-US `#` and `~`                |
-|`KC_NONUS_BSLASH`|`KC_NUBS`|Non-US `\` and <code>&#124;</code>|
-|`KC_INT1`        |`KC_RO`  |JIS `\` and <code>&#124;</code>   |
-|`KC_INT2`        |`KC_KANA`|JIS Katakana/Hiragana             |
-|`KC_INT3`        |`KC_JYEN`|JIS `¥`                           |
-|`KC_SCOLON`      |`KC_SCLN`|`;` and `:`                       |
-|`KC_QUOTE`       |`KC_QUOT`|`'` and `"`                       |
-|`KC_GRAVE`       |`KC_GRV` |<code>&#96;</code> and `~`        |
-|`KC_COMMA`       |`KC_COMM`|`,` and `<`                       |
-|`KC_DOT`         |         |`.` and `>`                       |
-|`KC_SLASH`       |`KC_SLSH`|`/` and `?`                       |
-|`KC_CAPSLOCK`    |`KC_CAPS`|Caps Lock                         |
+|Key              |Aliases            |Description                                    |
+|-----------------|-------------------|-----------------------------------------------|
+|`KC_ENTER`       |`KC_ENT`           |Return (Enter)                                 |
+|`KC_ESCAPE`      |`KC_ESC`           |Escape                                         |
+|`KC_BSPACE`      |`KC_BSPC`          |Delete (Backspace)                             |
+|`KC_TAB`         |                   |Tab                                            |
+|`KC_SPACE`       |`KC_SPC`           |Spacebar                                       |
+|`KC_MINUS`       |`KC_MINS`          |`-` and `_`                                    |
+|`KC_EQUAL`       |`KC_EQL`           |`=` and `+`                                    |
+|`KC_LBRACKET`    |`KC_LBRC`          |`[` and `{`                                    |
+|`KC_RBRACKET`    |`KC_RBRC`          |`]` and `}`                                    |
+|`KC_BSLASH`      |`KC_BSLS`          |`\` and <code>&#124;</code>                    |
+|`KC_NONUS_HASH`  |`KC_NUHS`          |Non-US `#` and `~`                             |
+|`KC_SCOLON`      |`KC_SCLN`          |`;` and `:`                                    |
+|`KC_QUOTE`       |`KC_QUOT`          |`'` and `"`                                    |
+|`KC_GRAVE`       |`KC_GRV`, `KC_ZKHK`|<code>&#96;</code> and `~`, JIS Zenkaku/Hankaku|
+|`KC_COMMA`       |`KC_COMM`          |`,` and `<`                                    |
+|`KC_DOT`         |                   |`.` and `>`                                    |
+|`KC_SLASH`       |`KC_SLSH`          |`/` and `?`                                    |
+|`KC_NONUS_BSLASH`|`KC_NUBS`          |Non-US `\` and <code>&#124;</code>             |
+
+## Lock Keys
+
+|Key                |Aliases             |Description              |
+|-------------------|--------------------|-------------------------|
+|`KC_CAPSLOCK`      |`KC_CLCK`, `KC_CAPS`|Caps Lock                |
+|`KC_SCROLLLOCK`    |`KC_SLCK`           |Scroll Lock              |
+|`KC_NUMLOCK`       |`KC_NLCK`           |Keypad Num Lock and Clear|
+|`KC_LOCKING_CAPS`  |`KC_LCAP`           |Locking Caps Lock        |
+|`KC_LOCKING_NUM`   |`KC_LNUM`           |Locking Num Lock         |
+|`KC_LOCKING_SCROLL`|`KC_LSCR`           |Locking Scroll Lock      |
 
 ## Modifiers
 
-|Key                |Aliases             |Description                         |
-|-------------------|--------------------|------------------------------------|
-|`KC_LCTRL`         |`KC_LCTL`           |Left Control                        |
-|`KC_LSHIFT`        |`KC_LSFT`           |Left Shift                          |
-|`KC_LALT`          |                    |Left Alt                            |
-|`KC_LGUI`          |`KC_LCMD`, `KC_LWIN`|Left GUI (Windows/Command/Meta key) |
-|`KC_RCTRL`         |`KC_RCTL`           |Right Control                       |
-|`KC_RSHIFT`        |`KC_RSFT`           |Right Shift                         |
-|`KC_RALT`          |                    |Right Alt                           |
-|`KC_RGUI`          |`KC_RCMD`, `KC_RWIN`|Right GUI (Windows/Command/Meta key)|
-|`KC_LOCKING_CAPS`  |`KC_LCAP`           |Locking Caps Lock                   |
-|`KC_LOCKING_NUM`   |`KC_LNUM`           |Locking Num Lock                    |
-|`KC_LOCKING_SCROLL`|`KC_LSCR`           |Locking Scroll Lock                 |
-|`KC_INT4`          |`KC_HENK`           |JIS Henkan                          |
-|`KC_INT5`          |`KC_MHEN`           |JIS Muhenkan                        |
+|Key        |Aliases             |Description                         |
+|-----------|--------------------|------------------------------------|
+|`KC_LCTRL` |`KC_LCTL`           |Left Control                        |
+|`KC_LSHIFT`|`KC_LSFT`           |Left Shift                          |
+|`KC_LALT`  |                    |Left Alt                            |
+|`KC_LGUI`  |`KC_LCMD`, `KC_LWIN`|Left GUI (Windows/Command/Meta key) |
+|`KC_RCTRL` |`KC_RCTL`           |Right Control                       |
+|`KC_RSHIFT`|`KC_RSFT`           |Right Shift                         |
+|`KC_RALT`  |                    |Right Alt                           |
+|`KC_RGUI`  |`KC_RCMD`, `KC_RWIN`|Right GUI (Windows/Command/Meta key)|
+
+## International
+
+|Key       |Aliases  |Description                    |
+|----------|---------|-------------------------------|
+|`KC_INT1` |`KC_RO`  |JIS `\` and <code>&#124;</code>|
+|`KC_INT2` |`KC_KANA`|JIS Katakana/Hiragana          |
+|`KC_INT3` |`KC_JYEN`|JIS `¥`                        |
+|`KC_INT4` |`KC_HENK`|JIS Henkan                     |
+|`KC_INT5` |`KC_MHEN`|JIS Muhenkan                   |
+|`KC_INT6` |         |JIS Numpad `,`                 |
+|`KC_INT7` |         |International 7                |
+|`KC_INT8` |         |International 8                |
+|`KC_INT9` |         |International 9                |
+|`KC_LANG1`|`KC_HAEN`|Hangul/English                 |
+|`KC_LANG2`|`KC_HANJ`|Hanja                          |
+|`KC_LANG3`|         |JIS Katakana                   |
+|`KC_LANG4`|         |JIS Hiragana                   |
+|`KC_LANG5`|         |JIS Zenkaku/Hankaku            |
+|`KC_LANG6`|         |Language 6                     |
+|`KC_LANG7`|         |Language 7                     |
+|`KC_LANG8`|         |Language 8                     |
+|`KC_LANG9`|         |Language 9                     |
 
 ## Commands
 
-|Key               |Aliases  |Description                   |
-|------------------|---------|------------------------------|
-|`KC_PSCREEN`      |`KC_PSCR`|Print Screen                  |
-|`KC_SCROLLLOCK`   |`KC_SLCK`|Scroll Lock                   |
-|`KC_PAUSE`        |`KC_PAUS`|Pause                         |
-|`KC_INSERT`       |`KC_INS` |Insert                        |
-|`KC_HOME`         |         |Home                          |
-|`KC_PGUP`         |         |Page Up                       |
-|`KC_DELETE`       |`KC_DEL` |Forward Delete                |
-|`KC_END`          |         |End                           |
-|`KC_PGDOWN`       |`KC_PGDN`|Page Down                     |
-|`KC_RIGHT`        |`KC_RGHT`|Right Arrow                   |
-|`KC_LEFT`         |         |Left Arrow                    |
-|`KC_DOWN`         |         |Down Arrow                    |
-|`KC_UP`           |         |Up Arrow                      |
-|`KC_APPLICATION`  |`KC_APP` |Application (Windows Menu Key)|
-|`KC_POWER`        |         |Power                         |
-|`KC_EXECUTE`      |         |Execute                       |
-|`KC_HELP`         |         |Help                          |
-|`KC_MENU`         |         |Menu                          |
-|`KC_SELECT`       |         |Select                        |
-|`KC_AGAIN`        |         |Again                         |
-|`KC_UNDO`         |         |Undo                          |
-|`KC_CUT`          |         |Cut                           |
-|`KC_COPY`         |         |Copy                          |
-|`KC_PASTE`        |         |Paste                         |
-|`KC_FIND`         |         |Find                          |
-|`KC_ALT_ERASE`    |         |Alternate Erase               |
-|`KC_SYSREQ`       |         |SysReq/Attention              |
-|`KC_CANCEL`       |         |Cancel                        |
-|`KC_CLEAR`        |         |Clear                         |
-|`KC_PRIOR`        |         |Prior                         |
-|`KC_RETURN`       |         |Return                        |
-|`KC_SEPARATOR`    |         |Separator                     |
-|`KC_OUT`          |         |Out                           |
-|`KC_OPER`         |         |Oper                          |
-|`KC_CLEAR_AGAIN`  |         |Clear/Again                   |
-|`KC_CRSEL`        |         |CrSel/Props                   |
-|`KC_EXSEL`        |         |ExSel                         |
+|Key               |Aliases            |Description                   |
+|------------------|-------------------|------------------------------|
+|`KC_PSCREEN`      |`KC_PSCR`          |Print Screen                  |
+|`KC_PAUSE`        |`KC_PAUS`, `KC_BRK`|Pause                         |
+|`KC_INSERT`       |`KC_INS`           |Insert                        |
+|`KC_HOME`         |                   |Home                          |
+|`KC_PGUP`         |                   |Page Up                       |
+|`KC_DELETE`       |`KC_DEL`           |Forward Delete                |
+|`KC_END`          |                   |End                           |
+|`KC_PGDOWN`       |`KC_PGDN`          |Page Down                     |
+|`KC_RIGHT`        |`KC_RGHT`          |Right Arrow                   |
+|`KC_LEFT`         |                   |Left Arrow                    |
+|`KC_DOWN`         |                   |Down Arrow                    |
+|`KC_UP`           |                   |Up Arrow                      |
+|`KC_APPLICATION`  |`KC_APP`           |Application (Windows Menu Key)|
+|`KC_POWER`        |                   |System Power (macOS/Linux)    |
+|`KC_EXECUTE`      |`KC_EXEC`          |Execute                       |
+|`KC_HELP`         |                   |Help                          |
+|`KC_MENU`         |                   |Menu                          |
+|`KC_SELECT`       |`KC_SLCT`          |Select                        |
+|`KC_STOP`         |                   |Stop                          |
+|`KC_AGAIN`        |`KC_AGIN`          |Again                         |
+|`KC_UNDO`         |                   |Undo                          |
+|`KC_CUT`          |                   |Cut                           |
+|`KC_COPY`         |                   |Copy                          |
+|`KC_PASTE`        |`KC_PSTE`          |Paste                         |
+|`KC_FIND`         |                   |Find                          |
+|`KC__MUTE`        |                   |Mute (macOS)                  |
+|`KC__VOLUP`       |                   |Volume Up (macOS)             |
+|`KC__VOLDOWN`     |                   |Volume Down (macOS)           |
+|`KC_ALT_ERASE`    |`KC_ERAS`          |Alternate Erase               |
+|`KC_SYSREQ`       |                   |SysReq/Attention              |
+|`KC_CANCEL`       |                   |Cancel                        |
+|`KC_CLEAR`        |`KC_CLR`           |Clear                         |
+|`KC_PRIOR`        |                   |Prior                         |
+|`KC_RETURN`       |                   |Return                        |
+|`KC_SEPARATOR`    |                   |Separator                     |
+|`KC_OUT`          |                   |Out                           |
+|`KC_OPER`         |                   |Oper                          |
+|`KC_CLEAR_AGAIN`  |                   |Clear/Again                   |
+|`KC_CRSEL`        |                   |CrSel/Props                   |
+|`KC_EXSEL`        |                   |ExSel                         |
 
 ## Media Keys
 
@@ -165,42 +193,37 @@ These keycodes are not part of the Keyboard/Keypad usage page. The `SYSTEM_` key
 
 Windows and macOS use different keycodes for "next track" and "previous track". Make sure you choose the keycode that corresponds to your OS.
 
-|Key                    |Aliases  |Description                      |
-|-----------------------|---------|---------------------------------|
-|`KC_SYSTEM_POWER`      |`KC_PWR` |System Power Down                |
-|`KC_SYSTEM_SLEEP`      |`KC_SLEP`|System Sleep                     |
-|`KC_SYSTEM_WAKE`       |`KC_WAKE`|System Wake                      |
-|`KC_MAIL`              |`KC_MAIL`|                                 |
-|`KC_CALCULATOR`        |`KC_CALC`|                                 |
-|`KC_MY_COMPUTER`       |`KC_MYCM`|                                 |
-|`KC_WWW_SEARCH`        |`KC_WSCH`|                                 |
-|`KC_WWW_HOME`          |`KC_WHOM`|                                 |
-|`KC_WWW_BACK`          |`KC_WBAK`|                                 |
-|`KC_WWW_FORWARD`       |`KC_WFWD`|                                 |
-|`KC_WWW_STOP`          |`KC_WSTP`|                                 |
-|`KC_WWW_REFRESH`       |`KC_WREF`|                                 |
-|`KC_STOP`              |         |Stop                             |
-|`KC_WWW_FAVORITES`     |`KC_WFAV`|                                 |
-|`KC__MUTE`             |         |Mute (macOS)                     |
-|`KC__VOLUP`            |         |Volume Up (macOS)                |
-|`KC__VOLDOWN`          |         |Volume Down (macOS)              |
-|`KC_AUDIO_MUTE`        |`KC_MUTE`|Mute (Windows/macOS/Linux)       |
-|`KC_AUDIO_VOL_UP`      |`KC_VOLU`|Volume Up (Windows/macOS/Linux)  |
-|`KC_AUDIO_VOL_DOWN`    |`KC_VOLD`|Volume Down (Windows/macOS/Linux)|
-|`KC_MEDIA_NEXT_TRACK`  |`KC_MNXT`|Next Track (Windows)             |
-|`KC_MEDIA_PREV_TRACK`  |`KC_MPRV`|Previous Track (Windows)         |
-|`KC_MEDIA_FAST_FORWARD`|`KC_MFFD`|Next Track (macOS)               |
-|`KC_MEDIA_REWIND`      |`KC_MRWD`|Previous Track (macOS)           |
-|`KC_MEDIA_STOP`        |`KC_MSTP`|Stop Track                       |
-|`KC_MEDIA_PLAY_PAUSE`  |`KC_MPLY`|Play/Pause Track                 |
-|`KC_MEDIA_SELECT`      |`KC_MSEL`|                                 |
-|`KC_MEDIA_EJECT`       |`KC_EJCT`|Eject (macOS)                    |
+|Key                    |Aliases  |Description                  |
+|-----------------------|---------|-----------------------------|
+|`KC_SYSTEM_POWER`      |`KC_PWR` |System Power Down            |
+|`KC_SYSTEM_SLEEP`      |`KC_SLEP`|System Sleep                 |
+|`KC_SYSTEM_WAKE`       |`KC_WAKE`|System Wake                  |
+|`KC_AUDIO_MUTE`        |`KC_MUTE`|Mute                         |
+|`KC_AUDIO_VOL_UP`      |`KC_VOLU`|Volume Up                    |
+|`KC_AUDIO_VOL_DOWN`    |`KC_VOLD`|Volume Down                  |
+|`KC_MEDIA_NEXT_TRACK`  |`KC_MNXT`|Next Track (Windows)         |
+|`KC_MEDIA_PREV_TRACK`  |`KC_MPRV`|Previous Track (Windows)     |
+|`KC_MEDIA_STOP`        |`KC_MSTP`|Stop Track (Windows)         |
+|`KC_MEDIA_PLAY_PAUSE`  |`KC_MPLY`|Play/Pause Track             |
+|`KC_MEDIA_SELECT`      |`KC_MSEL`|Launch Media Player (Windows)|
+|`KC_MEDIA_EJECT`       |`KC_EJCT`|Eject (macOS)                |
+|`KC_MAIL`              |         |Launch Mail (Windows)        |
+|`KC_CALCULATOR`        |`KC_CALC`|Launch Calculator (Windows)  |
+|`KC_MY_COMPUTER`       |`KC_MYCM`|Launch My Computer (Windows) |
+|`KC_WWW_SEARCH`        |`KC_WSCH`|Browser Search (Windows)     |
+|`KC_WWW_HOME`          |`KC_WHOM`|Browser Home (Windows)       |
+|`KC_WWW_BACK`          |`KC_WBAK`|Browser Back (Windows)       |
+|`KC_WWW_FORWARD`       |`KC_WFWD`|Browser Forward (Windows)    |
+|`KC_WWW_STOP`          |`KC_WSTP`|Browser Stop (Windows)       |
+|`KC_WWW_REFRESH`       |`KC_WREF`|Browser Refresh (Windows)    |
+|`KC_WWW_FAVORITES`     |`KC_WFAV`|Browser Favorites (Windows)  |
+|`KC_MEDIA_FAST_FORWARD`|`KC_MFFD`|Next Track (macOS)           |
+|`KC_MEDIA_REWIND`      |`KC_MRWD`|Previous Track (macOS)       |
 
 ## Number Pad
 
 |Key                |Aliases  |Description                   |
 |-------------------|---------|------------------------------|
-|`KC_NUMLOCK`       |`KC_NLCK`|Keypad Num Lock and Clear     |
 |`KC_KP_SLASH`      |`KC_PSLS`|Keypad `/`                    |
 |`KC_KP_ASTERISK`   |`KC_PAST`|Keypad `*`                    |
 |`KC_KP_MINUS`      |`KC_PMNS`|Keypad `-`                    |
@@ -225,7 +248,7 @@ Windows and macOS use different keycodes for "next track" and "previous track".
 
 In addition to these, keycodes in the range of `0xA5-DF` are reserved for internal use by TMK.
 
-|Key             |Aliases  |Description                            |
-|----------------|---------|---------------------------------------|
-|`KC_NO`         |         |Ignore this key (NOOP)                 |
-|`KC_TRANSPARENT`|`KC_TRNS`|Use the next lowest non-transparent key|
+|Key             |Aliases             |Description                            |
+|----------------|--------------------|---------------------------------------|
+|`KC_NO`         |`XXXXXXX`           |Ignore this key (NOOP)                 |
+|`KC_TRANSPARENT`|`KC_TRNS`, `_______`|Use the next lowest non-transparent key|

docs/keycodes_us_ansi_shifted.md

@@ -1,31 +1,33 @@
 # US ANSI Shifted Symbols
 
-These keycodes correspond to characters that are "shifted" on a standard US ANSI keyboards. They do not have dedicated keycodes but are instead typed by holding down shift and then sending a keycode.
+These keycodes correspond to characters that are "shifted" on a standard US ANSI keyboard. They do not have keycodes of their own but are simply shortcuts for `LSFT(kc)`, and as such send a Left Shift with the unshifted keycode, not the symbol itself.
 
-It's important to remember that all of these keycodes send a left shift - this may cause unintended actions if unaccounted for. The short code is preferred in most situations.
+## Caveats
 
-## US ANSI Shifted Keycodes
+Unfortunately, these keycodes cannot be used in Mod-Taps or Layer-Taps, since any modifiers specified in the keycode are ignored.
 
-|Key                     |Aliases           |Description        |
-|------------------------|------------------|-------------------|
-|`KC_TILDE`              |`KC_TILD`         |`~`                |
-|`KC_EXCLAIM`            |`KC_EXLM`         |`!`                |
-|`KC_AT`                 |                  |`@`                |
-|`KC_HASH`               |                  |`#`                |
-|`KC_DOLLAR`             |`KC_DLR`          |`$`                |
-|`KC_PERCENT`            |`KC_PERC`         |`%`                |
-|`KC_CIRCUMFLEX`         |`KC_CIRC`         |`^`                |
-|`KC_AMPERSAND`          |`KC_AMPR`         |`&`                |
-|`KC_ASTERISK`           |`KC_ASTR`         |`*`                |
-|`KC_LEFT_PAREN`         |`KC_LPRN`         |`(`                |
-|`KC_RIGHT_PAREN`        |`KC_RPRN`         |`)`                |
-|`KC_UNDERSCORE`         |`KC_UNDS`         |`_`                |
-|`KC_PLUS`               |                  |`+`                |
-|`KC_LEFT_CURLY_BRACE`   |`KC_LCBR`         |`{`                |
-|`KC_RIGHT_CURLY_BRACE`  |`KC_RCBR`         |`}`                |
-|`KC_PIPE`               |                  |<code>&#124;</code>|
-|`KC_COLON`              |`KC_COLN`         |`:`                |
-|`KC_DOUBLE_QUOTE`       |`KC_DQT`/`KC_DQUO`|`"`                |
-|`KC_LEFT_ANGLE_BRACKET` |`KC_LT`/`KC_LABK` |`<`                |
-|`KC_RIGHT_ANGLE_BRACKET`|`KC_GT`/`KC_RABK` |`>`                |
-|`KC_QUESTION`           |`KC_QUES`         |`?`                |
+## Keycodes
+
+|Key                     |Aliases            |Description        |
+|------------------------|-------------------|-------------------|
+|`KC_TILDE`              |`KC_TILD`          |`~`                |
+|`KC_EXCLAIM`            |`KC_EXLM`          |`!`                |
+|`KC_AT`                 |                   |`@`                |
+|`KC_HASH`               |                   |`#`                |
+|`KC_DOLLAR`             |`KC_DLR`           |`$`                |
+|`KC_PERCENT`            |`KC_PERC`          |`%`                |
+|`KC_CIRCUMFLEX`         |`KC_CIRC`          |`^`                |
+|`KC_AMPERSAND`          |`KC_AMPR`          |`&`                |
+|`KC_ASTERISK`           |`KC_ASTR`          |`*`                |
+|`KC_LEFT_PAREN`         |`KC_LPRN`          |`(`                |
+|`KC_RIGHT_PAREN`        |`KC_RPRN`          |`)`                |
+|`KC_UNDERSCORE`         |`KC_UNDS`          |`_`                |
+|`KC_PLUS`               |                   |`+`                |
+|`KC_LEFT_CURLY_BRACE`   |`KC_LCBR`          |`{`                |
+|`KC_RIGHT_CURLY_BRACE`  |`KC_RCBR`          |`}`                |
+|`KC_PIPE`               |                   |<code>&#124;</code>|
+|`KC_COLON`              |`KC_COLN`          |`:`                |
+|`KC_DOUBLE_QUOTE`       |`KC_DQUO`, `KC_DQT`|`"`                |
+|`KC_LEFT_ANGLE_BRACKET` |`KC_LABK`, `KC_LT` |`<`                |
+|`KC_RIGHT_ANGLE_BRACKET`|`KC_RABK`, `KC_GT` |`>`                |
+|`KC_QUESTION`           |`KC_QUES`          |`?`                |

docs/redirects.json

@@ -34,7 +34,7 @@
             },
             {
                 "from": "space_cadet_shift.html",
-                "to": "feature_space_cadet.html"
+                "to": "feature_space_cadet_shift.html"
             },
             {
                 "from": "tap_dance.html",

docs/reference_glossary.md

@@ -133,7 +133,7 @@ A 1 byte number that is sent as part of a HID report over USB that represents a
 ## Space Cadet Shift
 A special set of shift keys which allow you to type various types of braces by tapping the left or right shift one or more times.
 
-* [Space Cadet Shift Documentation](feature_space_cadet.md)
+* [Space Cadet Shift Documentation](feature_space_cadet_shift.md)
 
 ## Tap
 Pressing and releasing a key. In some situations you will need to distinguish between a key down and a key up event, and Tap always refers to both at once.

drivers/arm/i2c_master.c

@@ -0,0 +1,103 @@
+/* Copyright 2018 Jack Humbert
+ * Copyright 2018 Yiancar
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/* This library follows the convention of the AVR i2c_master library.
+ * As a result addresses are expected to be already shifted (addr << 1).
+ * I2CD1 is the default driver which corresponds to pins B6 and B7. This
+ * can be changed.
+ * Please ensure that HAL_USE_I2C is TRUE in the halconf.h file and that
+ * STM32_I2C_USE_I2C1 is TRUE in the mcuconf.h file.
+ */
+
+#include "i2c_master.h"
+#include <string.h>
+#include <hal.h>
+
+static uint8_t i2c_address;
+
+// This configures the I2C clock to 400Mhz assuming a 72Mhz clock
+// For more info : https://www.st.com/en/embedded-software/stsw-stm32126.html
+static const I2CConfig i2cconfig = {
+  STM32_TIMINGR_PRESC(15U) |
+  STM32_TIMINGR_SCLDEL(4U) | STM32_TIMINGR_SDADEL(2U) |
+  STM32_TIMINGR_SCLH(15U)  | STM32_TIMINGR_SCLL(21U),
+  0,
+  0
+};
+
+void i2c_init(void)
+{
+  palSetGroupMode(GPIOB,6,7, PAL_MODE_INPUT);       // Try releasing special pins for a short time
+  chThdSleepMilliseconds(10);
+
+  palSetPadMode(GPIOB, 6, PAL_MODE_ALTERNATE(4) | PAL_STM32_OTYPE_OPENDRAIN | PAL_STM32_PUPDR_PULLUP);
+  palSetPadMode(GPIOB, 7, PAL_MODE_ALTERNATE(4) | PAL_STM32_OTYPE_OPENDRAIN | PAL_STM32_PUPDR_PULLUP);
+
+  //i2cInit(); //This is invoked by halInit() so no need to redo it.
+}
+
+// This is usually not needed
+uint8_t i2c_start(uint8_t address)
+{
+  i2c_address = address;
+  i2cStart(&I2C_DRIVER, &i2cconfig);
+  return 0;
+}
+
+uint8_t i2c_transmit(uint8_t address, uint8_t* data, uint16_t length, uint16_t timeout)
+{
+  i2c_address = address;
+  i2cStart(&I2C_DRIVER, &i2cconfig);
+  return i2cMasterTransmitTimeout(&I2C_DRIVER, (i2c_address >> 1), data, length, 0, 0, MS2ST(timeout));
+}
+
+uint8_t i2c_receive(uint8_t address, uint8_t* data, uint16_t length, uint16_t timeout)
+{
+  i2c_address = address;
+  i2cStart(&I2C_DRIVER, &i2cconfig);
+  return i2cMasterReceiveTimeout(&I2C_DRIVER, (i2c_address >> 1), data, length, MS2ST(timeout));
+}
+
+uint8_t i2c_writeReg(uint8_t devaddr, uint8_t regaddr, uint8_t* data, uint16_t length, uint16_t timeout)
+{
+  i2c_address = devaddr;
+  i2cStart(&I2C_DRIVER, &i2cconfig);
+
+  uint8_t complete_packet[length + 1];
+  for(uint8_t i = 0; i < length; i++)
+  {
+    complete_packet[i+1] = data[i];
+  }
+  complete_packet[0] = regaddr
+
+  return i2cMasterTransmitTimeout(&I2C_DRIVER, (i2c_address >> 1), complete_packet, length + 1, 0, 0, MS2ST(timeout));
+}
+
+uint8_t i2c_readReg(uint8_t devaddr, uint8_t regaddr, uint8_t* data, uint16_t length, uint16_t timeout)
+{
+  i2c_address = devaddr;
+  i2cStart(&I2C_DRIVER, &i2cconfig);
+  return i2cMasterTransmitTimeout(&I2C_DRIVER, (i2c_address >> 1), regaddr, 1, data, length, MS2ST(timeout));
+}
+
+// This is usually not needed. It releases the driver to allow pins to become GPIO again.
+uint8_t i2c_stop(uint16_t timeout)
+{
+  i2c_address = address;
+  i2cStop(&I2C_DRIVER);
+  return 0;
+}

drivers/arm/i2c_master.h

@@ -0,0 +1,39 @@
+/* Copyright 2018 Jack Humbert
+ * Copyright 2018 Yiancar
+ *
+ * This program is free sofare: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Sofare Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/* This library follows the convention of the AVR i2c_master library.
+ * As a result addresses are expected to be already shifted (addr << 1).
+ * I2CD1 is the default driver which corresponds to pins B6 and B7. This
+ * can be changed.
+ * Please ensure that HAL_USE_I2C is TRUE in the halconf.h file and that
+ * STM32_I2C_USE_I2C1 is TRUE in the mcuconf.h file.
+ */
+
+#include "ch.h"
+#include <hal.h>
+
+#ifndef I2C_DRIVER
+  #define I2C_DRIVER I2CD1
+#endif
+
+void i2c_init(void);
+uint8_t i2c_start(uint8_t address);
+uint8_t i2c_transmit(uint8_t address, uint8_t* data, uint16_t length, uint16_t timeout);
+uint8_t i2c_receive(uint8_t address, uint8_t* data, uint16_t length, uint16_t timeout);
+uint8_t i2c_writeReg(uint8_t devaddr, uint8_t regaddr, uint8_t* data, uint16_t length, uint16_t timeout);
+uint8_t i2c_readReg(uint8_t devaddr, uint8_t regaddr, uint8_t* data, uint16_t length, uint16_t timeout);
+void i2c_stop(void);

drivers/avr/i2c_master.c

@@ -15,15 +15,15 @@
 void i2c_init(void)
 {
   TWSR = 0;     /* no prescaler */
-	TWBR = (uint8_t)TWBR_val;
+  TWBR = (uint8_t)TWBR_val;
 }
 
 i2c_status_t i2c_start(uint8_t address, uint16_t timeout)
 {
-	// reset TWI control register
-	TWCR = 0;
-	// transmit START condition
-	TWCR = (1<<TWINT) | (1<<TWSTA) | (1<<TWEN);
+  // reset TWI control register
+  TWCR = 0;
+  // transmit START condition
+  TWCR = (1<<TWINT) | (1<<TWSTA) | (1<<TWEN);
 
   uint16_t timeout_timer = timer_read();
   while( !(TWCR & (1<<TWINT)) ) {
@@ -32,13 +32,13 @@ i2c_status_t i2c_start(uint8_t address, uint16_t timeout)
     }
   }
 
-	// check if the start condition was successfully transmitted
-	if(((TW_STATUS & 0xF8) != TW_START) && ((TW_STATUS & 0xF8) != TW_REP_START)){ return I2C_STATUS_ERROR; }
+  // check if the start condition was successfully transmitted
+  if(((TW_STATUS & 0xF8) != TW_START) && ((TW_STATUS & 0xF8) != TW_REP_START)){ return I2C_STATUS_ERROR; }
 
-	// load slave address into data register
-	TWDR = address;
-	// start transmission of address
-	TWCR = (1<<TWINT) | (1<<TWEN);
+  // load slave address into data register
+  TWDR = address;
+  // start transmission of address
+  TWCR = (1<<TWINT) | (1<<TWEN);
 
   timeout_timer = timer_read();
   while( !(TWCR & (1<<TWINT)) ) {
@@ -47,19 +47,19 @@ i2c_status_t i2c_start(uint8_t address, uint16_t timeout)
     }
   }
 
-	// check if the device has acknowledged the READ / WRITE mode
-	uint8_t twst = TW_STATUS & 0xF8;
-	if ( (twst != TW_MT_SLA_ACK) && (twst != TW_MR_SLA_ACK) ) return I2C_STATUS_ERROR;
+  // check if the device has acknowledged the READ / WRITE mode
+  uint8_t twst = TW_STATUS & 0xF8;
+  if ( (twst != TW_MT_SLA_ACK) && (twst != TW_MR_SLA_ACK) ) return I2C_STATUS_ERROR;
 
-	return I2C_STATUS_SUCCESS;
+  return I2C_STATUS_SUCCESS;
 }
 
 i2c_status_t i2c_write(uint8_t data, uint16_t timeout)
 {
-	// load data into data register
-	TWDR = data;
-	// start transmission of data
-	TWCR = (1<<TWINT) | (1<<TWEN);
+  // load data into data register
+  TWDR = data;
+  // start transmission of data
+  TWCR = (1<<TWINT) | (1<<TWEN);
 
   uint16_t timeout_timer = timer_read();
   while( !(TWCR & (1<<TWINT)) ) {
@@ -68,16 +68,16 @@ i2c_status_t i2c_write(uint8_t data, uint16_t timeout)
     }
   }
 
-	if( (TW_STATUS & 0xF8) != TW_MT_DATA_ACK ){ return I2C_STATUS_ERROR; }
+  if( (TW_STATUS & 0xF8) != TW_MT_DATA_ACK ){ return I2C_STATUS_ERROR; }
 
-	return I2C_STATUS_SUCCESS;
+  return I2C_STATUS_SUCCESS;
 }
 
 int16_t i2c_read_ack(uint16_t timeout)
 {
 
-	// start TWI module and acknowledge data after reception
-	TWCR = (1<<TWINT) | (1<<TWEN) | (1<<TWEA);
+  // start TWI module and acknowledge data after reception
+  TWCR = (1<<TWINT) | (1<<TWEN) | (1<<TWEA);
 
   uint16_t timeout_timer = timer_read();
   while( !(TWCR & (1<<TWINT)) ) {
@@ -86,15 +86,15 @@ int16_t i2c_read_ack(uint16_t timeout)
     }
   }
 
-	// return received data from TWDR
-	return TWDR;
+  // return received data from TWDR
+  return TWDR;
 }
 
 int16_t i2c_read_nack(uint16_t timeout)
 {
 
-	// start receiving without acknowledging reception
-	TWCR = (1<<TWINT) | (1<<TWEN);
+  // start receiving without acknowledging reception
+  TWCR = (1<<TWINT) | (1<<TWEN);
 
   uint16_t timeout_timer = timer_read();
   while( !(TWCR & (1<<TWINT)) ) {
@@ -103,39 +103,39 @@ int16_t i2c_read_nack(uint16_t timeout)
     }
   }
 
-	// return received data from TWDR
-	return TWDR;
+  // return received data from TWDR
+  return TWDR;
 }
 
 i2c_status_t i2c_transmit(uint8_t address, uint8_t* data, uint16_t length, uint16_t timeout)
 {
   i2c_status_t status = i2c_start(address | I2C_WRITE, timeout);
-	if (status) return status;
-
-	for (uint16_t i = 0; i < length; i++) {
-		status = i2c_write(data[i], timeout);
-    if (status) return status;
-	}
-
-	status = i2c_stop(timeout);
   if (status) return status;
 
-	return I2C_STATUS_SUCCESS;
+  for (uint16_t i = 0; i < length; i++) {
+    status = i2c_write(data[i], timeout);
+    if (status) return status;
+  }
+
+  status = i2c_stop(timeout);
+  if (status) return status;
+
+  return I2C_STATUS_SUCCESS;
 }
 
 i2c_status_t i2c_receive(uint8_t address, uint8_t* data, uint16_t length, uint16_t timeout)
 {
   i2c_status_t status = i2c_start(address | I2C_READ, timeout);
-	if (status) return status;
+  if (status) return status;
 
-	for (uint16_t i = 0; i < (length-1); i++) {
+  for (uint16_t i = 0; i < (length-1); i++) {
     status = i2c_read_ack(timeout);
     if (status >= 0) {
       data[i] = status;
     } else {
       return status;
     }
-	}
+  }
 
   status = i2c_read_nack(timeout);
   if (status >= 0 ) {
@@ -147,47 +147,47 @@ i2c_status_t i2c_receive(uint8_t address, uint8_t* data, uint16_t length, uint16
   status = i2c_stop(timeout);
   if (status) return status;
 
-	return I2C_STATUS_SUCCESS;
+  return I2C_STATUS_SUCCESS;
 }
 
 i2c_status_t i2c_writeReg(uint8_t devaddr, uint8_t regaddr, uint8_t* data, uint16_t length, uint16_t timeout)
 {
   i2c_status_t status = i2c_start(devaddr | 0x00, timeout);
-	if (status) return status;
-
-	status = i2c_write(regaddr, timeout);
   if (status) return status;
 
-	for (uint16_t i = 0; i < length; i++) {
+  status = i2c_write(regaddr, timeout);
+  if (status) return status;
+
+  for (uint16_t i = 0; i < length; i++) {
     status = i2c_write(data[i], timeout);
-		if (status) return status;
-	}
+    if (status) return status;
+  }
 
-	status = i2c_stop(timeout);
+  status = i2c_stop(timeout);
   if (status) return status;
 
-	return I2C_STATUS_SUCCESS;
+  return I2C_STATUS_SUCCESS;
 }
 
 i2c_status_t i2c_readReg(uint8_t devaddr, uint8_t regaddr, uint8_t* data, uint16_t length, uint16_t timeout)
 {
   i2c_status_t status = i2c_start(devaddr, timeout);
-	if (status) return status;
+  if (status) return status;
 
   status = i2c_write(regaddr, timeout);
   if (status) return status;
 
   status = i2c_start(devaddr | 0x01, timeout);
-	if (status) return status;
+  if (status) return status;
 
-	for (uint16_t i = 0; i < (length-1); i++) {
-		status = i2c_read_ack(timeout);
+  for (uint16_t i = 0; i < (length-1); i++) {
+    status = i2c_read_ack(timeout);
     if (status >= 0) {
       data[i] = status;
     } else {
       return status;
     }
-	}
+  }
 
   status = i2c_read_nack(timeout);
   if (status >= 0 ) {
@@ -199,13 +199,13 @@ i2c_status_t i2c_readReg(uint8_t devaddr, uint8_t regaddr, uint8_t* data, uint16
   status = i2c_stop(timeout);
   if (status) return status;
 
-	return I2C_STATUS_SUCCESS;
+  return I2C_STATUS_SUCCESS;
 }
 
 i2c_status_t i2c_stop(uint16_t timeout)
 {
-	// transmit STOP condition
-	TWCR = (1<<TWINT) | (1<<TWEN) | (1<<TWSTO);
+  // transmit STOP condition
+  TWCR = (1<<TWINT) | (1<<TWEN) | (1<<TWSTO);
 
   uint16_t timeout_timer = timer_read();
   while(TWCR & (1<<TWSTO)) {
@@ -215,4 +215,4 @@ i2c_status_t i2c_stop(uint16_t timeout)
   }
 
   return I2C_STATUS_SUCCESS;
-}
+}

drivers/avr/i2c_master.h

@@ -28,4 +28,4 @@ i2c_status_t i2c_writeReg(uint8_t devaddr, uint8_t regaddr, uint8_t* data, uint1
 i2c_status_t i2c_readReg(uint8_t devaddr, uint8_t regaddr, uint8_t* data, uint16_t length, uint16_t timeout);
 i2c_status_t i2c_stop(uint16_t timeout);
 
-#endif // I2C_MASTER_H
+#endif // I2C_MASTER_H

drivers/avr/i2c_slave.c

@@ -5,96 +5,64 @@
 #include <avr/io.h>
 #include <util/twi.h>
 #include <avr/interrupt.h>
+#include <stdbool.h>
 
 #include "i2c_slave.h"
 
 void i2c_init(uint8_t address){
-	// load address into TWI address register
-	TWAR = (address << 1);
-	// set the TWCR to enable address matching and enable TWI, clear TWINT, enable TWI interrupt
-	TWCR = (1<<TWIE) | (1<<TWEA) | (1<<TWINT) | (1<<TWEN);
+    // load address into TWI address register
+    TWAR = (address << 1);
+    // set the TWCR to enable address matching and enable TWI, clear TWINT, enable TWI interrupt
+    TWCR = (1 << TWIE) | (1 << TWEA) | (1 << TWINT) | (1 << TWEN);
 }
 
 void i2c_stop(void){
-	// clear acknowledge and enable bits
-	TWCR &= ~( (1<<TWEA) | (1<<TWEN) );
+    // clear acknowledge and enable bits
+    TWCR &= ~((1 << TWEA) | (1 << TWEN));
 }
 
 ISR(TWI_vect){
-	
-	// temporary stores the received data
-	uint8_t data;
-	
-	// own address has been acknowledged
-	if( (TWSR & 0xF8) == TW_SR_SLA_ACK ){  
-		buffer_address = 0xFF;
-		// clear TWI interrupt flag, prepare to receive next byte and acknowledge
-		TWCR |= (1<<TWIE) | (1<<TWINT) | (1<<TWEA) | (1<<TWEN); 
-	}
-	else if( (TWSR & 0xF8) == TW_SR_DATA_ACK ){ // data has been received in slave receiver mode
-		
-		// save the received byte inside data 
-		data = TWDR;
-		
-		// check wether an address has already been transmitted or not
-		if(buffer_address == 0xFF){
-			
-			buffer_address = data; 
-			
-			// clear TWI interrupt flag, prepare to receive next byte and acknowledge
-			TWCR |= (1<<TWIE) | (1<<TWINT) | (1<<TWEA) | (1<<TWEN); 
-		}
-		else{ // if a databyte has already been received
-			
-			// store the data at the current address
-			rxbuffer[buffer_address] = data;
-			
-			// increment the buffer address
-			buffer_address++;
-			
-			// if there is still enough space inside the buffer
-			if(buffer_address < 0xFF){
-				// clear TWI interrupt flag, prepare to receive next byte and acknowledge
-				TWCR |= (1<<TWIE) | (1<<TWINT) | (1<<TWEA) | (1<<TWEN); 
-			}
-			else{
-				// Don't acknowledge
-				TWCR &= ~(1<<TWEA); 
-				// clear TWI interrupt flag, prepare to receive last byte.
-				TWCR |= (1<<TWIE) | (1<<TWINT) | (1<<TWEN); 
-			}
-		}
-	}
-	else if( (TWSR & 0xF8) == TW_ST_DATA_ACK ){ // device has been addressed to be a transmitter
-		
-		// copy data from TWDR to the temporary memory
-		data = TWDR;
-		
-		// if no buffer read address has been sent yet
-		if( buffer_address == 0xFF ){
-			buffer_address = data;
-		}
-		
-		// copy the specified buffer address into the TWDR register for transmission
-		TWDR = txbuffer[buffer_address];
-		// increment buffer read address
-		buffer_address++;
-		
-		// if there is another buffer address that can be sent
-		if(buffer_address < 0xFF){
-			// clear TWI interrupt flag, prepare to send next byte and receive acknowledge
-			TWCR |= (1<<TWIE) | (1<<TWINT) | (1<<TWEA) | (1<<TWEN); 
-		}
-		else{
-			// Don't acknowledge
-			TWCR &= ~(1<<TWEA); 
-			// clear TWI interrupt flag, prepare to receive last byte.
-			TWCR |= (1<<TWIE) | (1<<TWINT) | (1<<TWEN); 
-		}
-		
-	}
-	else{
-		// if none of the above apply prepare TWI to be addressed again
-		TWCR |= (1<<TWIE) | (1<<TWEA) | (1<<TWEN);
-	} 
-}
+    uint8_t ack = 1;
+    // temporary stores the received data
+    //uint8_t data;
+    
+    switch(TW_STATUS){
+        case TW_SR_SLA_ACK:
+            // The device is now a slave receiver
+            slave_has_register_set = false;
+            break;
+
+        case TW_SR_DATA_ACK:
+            // This device is a slave receiver and has received data
+            // First byte is the location then the bytes will be writen in buffer with auto-incriment
+            if(!slave_has_register_set){
+                buffer_address = TWDR;
+
+                if (buffer_address >= RX_BUFFER_SIZE){ // address out of bounds dont ack
+                    ack = 0;
+                    buffer_address = 0;
+                }
+                slave_has_register_set = true; // address has been receaved now fill in buffer
+            } else {
+                rxbuffer[buffer_address] = TWDR;
+                buffer_address++;
+            }
+            break;
+
+        case TW_ST_SLA_ACK:
+        case TW_ST_DATA_ACK:
+            // This device is a slave transmitter and master has requested data
+            TWDR = txbuffer[buffer_address];
+            buffer_address++;
+            break;
+
+        case TW_BUS_ERROR:
+            // We got an error, reset i2c
+            TWCR = 0;
+        default:
+            break;
+    }
+
+    // Reset i2c state mahcine to be ready for next interrupt
+    TWCR |= (1 << TWIE) | (1 << TWINT) | (ack << TWEA) | (1 << TWEN);
+}

drivers/avr/i2c_slave.h

@@ -8,12 +8,16 @@
 #ifndef I2C_SLAVE_H
 #define I2C_SLAVE_H
 
+#define TX_BUFFER_SIZE 30
+#define RX_BUFFER_SIZE 30
+
 volatile uint8_t buffer_address;
-volatile uint8_t txbuffer[0xFF];
-volatile uint8_t rxbuffer[0xFF];
+static volatile bool slave_has_register_set = false;
+volatile uint8_t txbuffer[TX_BUFFER_SIZE];
+volatile uint8_t rxbuffer[RX_BUFFER_SIZE];
 
 void i2c_init(uint8_t address);
 void i2c_stop(void);
 ISR(TWI_vect);
 
-#endif // I2C_SLAVE_H
+#endif // I2C_SLAVE_H

drivers/avr/is31fl3731.c

@@ -1,262 +0,0 @@
-/* Copyright 2017 Jason Williams
- * Copyright 2018 Jack Humbert
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
- */
-
-#include "is31fl3731.h"
-#include <avr/interrupt.h>
-#include <avr/io.h>
-#include <util/delay.h>
-#include <string.h>
-#include "i2c_master.h"
-#include "progmem.h"
-
-// This is a 7-bit address, that gets left-shifted and bit 0
-// set to 0 for write, 1 for read (as per I2C protocol)
-// The address will vary depending on your wiring:
-// 0b1110100 AD <-> GND
-// 0b1110111 AD <-> VCC
-// 0b1110101 AD <-> SCL
-// 0b1110110 AD <-> SDA
-#define ISSI_ADDR_DEFAULT 0x74
-
-#define ISSI_REG_CONFIG  0x00
-#define ISSI_REG_CONFIG_PICTUREMODE 0x00
-#define ISSI_REG_CONFIG_AUTOPLAYMODE 0x08
-#define ISSI_REG_CONFIG_AUDIOPLAYMODE 0x18
-
-#define ISSI_CONF_PICTUREMODE 0x00
-#define ISSI_CONF_AUTOFRAMEMODE 0x04
-#define ISSI_CONF_AUDIOMODE 0x08
-
-#define ISSI_REG_PICTUREFRAME  0x01
-
-#define ISSI_REG_SHUTDOWN 0x0A
-#define ISSI_REG_AUDIOSYNC 0x06
-
-#define ISSI_COMMANDREGISTER 0xFD
-#define ISSI_BANK_FUNCTIONREG 0x0B    // helpfully called 'page nine'
-
-#ifndef ISSI_TIMEOUT
-  #define ISSI_TIMEOUT 100
-#endif
-
-#ifndef ISSI_PERSISTENCE
-  #define ISSI_PERSISTENCE 0
-#endif
-
-// Transfer buffer for TWITransmitData()
-uint8_t g_twi_transfer_buffer[20];
-
-// These buffers match the IS31FL3731 PWM registers 0x24-0xB3.
-// Storing them like this is optimal for I2C transfers to the registers.
-// We could optimize this and take out the unused registers from these
-// buffers and the transfers in IS31FL3731_write_pwm_buffer() but it's
-// probably not worth the extra complexity.
-uint8_t g_pwm_buffer[DRIVER_COUNT][144];
-bool g_pwm_buffer_update_required = false;
-
-uint8_t g_led_control_registers[DRIVER_COUNT][18] = { { 0 }, { 0 } };
-bool g_led_control_registers_update_required = false;
-
-// This is the bit pattern in the LED control registers
-// (for matrix A, add one to register for matrix B)
-//
-//  reg -  b7  b6  b5  b4  b3  b2  b1  b0
-// 0x00 - R08,R07,R06,R05,R04,R03,R02,R01
-// 0x02 - G08,G07,G06,G05,G04,G03,G02,R00
-// 0x04 - B08,B07,B06,B05,B04,B03,G01,G00
-// 0x06 -  - , - , - , - , - ,B02,B01,B00
-// 0x08 -  - , - , - , - , - , - , - , -
-// 0x0A - B17,B16,B15, - , - , - , - , -
-// 0x0C - G17,G16,B14,B13,B12,B11,B10,B09
-// 0x0E - R17,G15,G14,G13,G12,G11,G10,G09
-// 0x10 - R16,R15,R14,R13,R12,R11,R10,R09
-
-
-void IS31FL3731_write_register( uint8_t addr, uint8_t reg, uint8_t data )
-{
-	g_twi_transfer_buffer[0] = reg;
-	g_twi_transfer_buffer[1] = data;
-
-  #if ISSI_PERSISTENCE > 0
-    for (uint8_t i = 0; i < ISSI_PERSISTENCE; i++) {
-      if (i2c_transmit(addr << 1, g_twi_transfer_buffer, 2, ISSI_TIMEOUT) == 0)
-        break;
-    }
-  #else
-    i2c_transmit(addr << 1, g_twi_transfer_buffer, 2, ISSI_TIMEOUT);
-  #endif
-}
-
-void IS31FL3731_write_pwm_buffer( uint8_t addr, uint8_t *pwm_buffer )
-{
-	// assumes bank is already selected
-
-	// transmit PWM registers in 9 transfers of 16 bytes
-	// g_twi_transfer_buffer[] is 20 bytes
-
-	// iterate over the pwm_buffer contents at 16 byte intervals
-	for ( int i = 0; i < 144; i += 16 ) {
-		// set the first register, e.g. 0x24, 0x34, 0x44, etc.
-		g_twi_transfer_buffer[0] = 0x24 + i;
-		// copy the data from i to i+15
-		// device will auto-increment register for data after the first byte
-		// thus this sets registers 0x24-0x33, 0x34-0x43, etc. in one transfer
-		for ( int j = 0; j < 16; j++ ) {
-			g_twi_transfer_buffer[1 + j] = pwm_buffer[i + j];
-		}
-
-    #if ISSI_PERSISTENCE > 0
-      for (uint8_t i = 0; i < ISSI_PERSISTENCE; i++) {
-        if (i2c_transmit(addr << 1, g_twi_transfer_buffer, 17, ISSI_TIMEOUT) == 0)
-          break;
-      }
-    #else
-      i2c_transmit(addr << 1, g_twi_transfer_buffer, 17, ISSI_TIMEOUT);
-    #endif
-	}
-}
-
-void IS31FL3731_init( uint8_t addr )
-{
-	// In order to avoid the LEDs being driven with garbage data
-	// in the LED driver's PWM registers, first enable software shutdown,
-	// then set up the mode and other settings, clear the PWM registers,
-	// then disable software shutdown.
-
-	// select "function register" bank
-	IS31FL3731_write_register( addr, ISSI_COMMANDREGISTER, ISSI_BANK_FUNCTIONREG );
-
-	// enable software shutdown
-	IS31FL3731_write_register( addr, ISSI_REG_SHUTDOWN, 0x00 );
-	// this delay was copied from other drivers, might not be needed
-	_delay_ms( 10 );
-
-	// picture mode
-	IS31FL3731_write_register( addr, ISSI_REG_CONFIG, ISSI_REG_CONFIG_PICTUREMODE );
-	// display frame 0
-	IS31FL3731_write_register( addr, ISSI_REG_PICTUREFRAME, 0x00 );
-	// audio sync off
-	IS31FL3731_write_register( addr, ISSI_REG_AUDIOSYNC, 0x00 );
-
-	// select bank 0
-	IS31FL3731_write_register( addr, ISSI_COMMANDREGISTER, 0 );
-
-	// turn off all LEDs in the LED control register
-	for ( int i = 0x00; i <= 0x11; i++ )
-	{
-		IS31FL3731_write_register( addr, i, 0x00 );
-	}
-
-	// turn off all LEDs in the blink control register (not really needed)
-	for ( int i = 0x12; i <= 0x23; i++ )
-	{
-		IS31FL3731_write_register( addr, i, 0x00 );
-	}
-
-	// set PWM on all LEDs to 0
-	for ( int i = 0x24; i <= 0xB3; i++ )
-	{
-		IS31FL3731_write_register( addr, i, 0x00 );
-	}
-
-	// select "function register" bank
-	IS31FL3731_write_register( addr, ISSI_COMMANDREGISTER, ISSI_BANK_FUNCTIONREG );
-
-	// disable software shutdown
-	IS31FL3731_write_register( addr, ISSI_REG_SHUTDOWN, 0x01 );
-
-	// select bank 0 and leave it selected.
-	// most usage after initialization is just writing PWM buffers in bank 0
-	// as there's not much point in double-buffering
-	IS31FL3731_write_register( addr, ISSI_COMMANDREGISTER, 0 );
-
-}
-
-void IS31FL3731_set_color( int index, uint8_t red, uint8_t green, uint8_t blue )
-{
-	if ( index >= 0 && index < DRIVER_LED_TOTAL ) {
-		is31_led led = g_is31_leds[index];
-
-		// Subtract 0x24 to get the second index of g_pwm_buffer
-		g_pwm_buffer[led.driver][led.r - 0x24] = red;
-		g_pwm_buffer[led.driver][led.g - 0x24] = green;
-		g_pwm_buffer[led.driver][led.b - 0x24] = blue;
-		g_pwm_buffer_update_required = true;
-	}
-}
-
-void IS31FL3731_set_color_all( uint8_t red, uint8_t green, uint8_t blue )
-{
-	for ( int i = 0; i < DRIVER_LED_TOTAL; i++ )
-	{
-		IS31FL3731_set_color( i, red, green, blue );
-	}
-}
-
-void IS31FL3731_set_led_control_register( uint8_t index, bool red, bool green, bool blue )
-{
-	is31_led led = g_is31_leds[index];
-
-  uint8_t control_register_r = (led.r - 0x24) / 8;
-  uint8_t control_register_g = (led.g - 0x24) / 8;
-  uint8_t control_register_b = (led.b - 0x24) / 8;
-  uint8_t bit_r = (led.r - 0x24) % 8;
-  uint8_t bit_g = (led.g - 0x24) % 8;
-  uint8_t bit_b = (led.b - 0x24) % 8;
-
-	if ( red ) {
-		g_led_control_registers[led.driver][control_register_r] |= (1 << bit_r);
-	} else {
-		g_led_control_registers[led.driver][control_register_r] &= ~(1 << bit_r);
-	}
-	if ( green ) {
-		g_led_control_registers[led.driver][control_register_g] |= (1 << bit_g);
-	} else {
-		g_led_control_registers[led.driver][control_register_g] &= ~(1 << bit_g);
-	}
-	if ( blue ) {
-		g_led_control_registers[led.driver][control_register_b] |= (1 << bit_b);
-	} else {
-		g_led_control_registers[led.driver][control_register_b] &= ~(1 << bit_b);
-	}
-
-	g_led_control_registers_update_required = true;
-
-}
-
-void IS31FL3731_update_pwm_buffers( uint8_t addr1, uint8_t addr2 )
-{
-	if ( g_pwm_buffer_update_required )
-	{
-		IS31FL3731_write_pwm_buffer( addr1, g_pwm_buffer[0] );
-		IS31FL3731_write_pwm_buffer( addr2, g_pwm_buffer[1] );
-	}
-	g_pwm_buffer_update_required = false;
-}
-
-void IS31FL3731_update_led_control_registers( uint8_t addr1, uint8_t addr2 )
-{
-	if ( g_led_control_registers_update_required )
-	{
-		for ( int i=0; i<18; i++ )
-		{
-			IS31FL3731_write_register(addr1, i, g_led_control_registers[0][i] );
-			IS31FL3731_write_register(addr2, i, g_led_control_registers[1][i] );
-		}
-	}
-}
-

drivers/is31fl3731.c

@@ -0,0 +1,271 @@
+/* Copyright 2017 Jason Williams
+ * Copyright 2018 Jack Humbert
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifdef __AVR__
+#include <avr/interrupt.h>
+#include <avr/io.h>
+#include <util/delay.h>
+#else
+#include "wait.h"
+#endif
+
+#include "is31fl3731.h"
+#include <string.h>
+#include "i2c_master.h"
+#include "progmem.h"
+
+// This is a 7-bit address, that gets left-shifted and bit 0
+// set to 0 for write, 1 for read (as per I2C protocol)
+// The address will vary depending on your wiring:
+// 0b1110100 AD <-> GND
+// 0b1110111 AD <-> VCC
+// 0b1110101 AD <-> SCL
+// 0b1110110 AD <-> SDA
+#define ISSI_ADDR_DEFAULT 0x74
+
+#define ISSI_REG_CONFIG  0x00
+#define ISSI_REG_CONFIG_PICTUREMODE 0x00
+#define ISSI_REG_CONFIG_AUTOPLAYMODE 0x08
+#define ISSI_REG_CONFIG_AUDIOPLAYMODE 0x18
+
+#define ISSI_CONF_PICTUREMODE 0x00
+#define ISSI_CONF_AUTOFRAMEMODE 0x04
+#define ISSI_CONF_AUDIOMODE 0x08
+
+#define ISSI_REG_PICTUREFRAME  0x01
+
+#define ISSI_REG_SHUTDOWN 0x0A
+#define ISSI_REG_AUDIOSYNC 0x06
+
+#define ISSI_COMMANDREGISTER 0xFD
+#define ISSI_BANK_FUNCTIONREG 0x0B    // helpfully called 'page nine'
+
+#ifndef ISSI_TIMEOUT
+  #define ISSI_TIMEOUT 100
+#endif
+
+#ifndef ISSI_PERSISTENCE
+  #define ISSI_PERSISTENCE 0
+#endif
+
+// Transfer buffer for TWITransmitData()
+uint8_t g_twi_transfer_buffer[20];
+
+// These buffers match the IS31FL3731 PWM registers 0x24-0xB3.
+// Storing them like this is optimal for I2C transfers to the registers.
+// We could optimize this and take out the unused registers from these
+// buffers and the transfers in IS31FL3731_write_pwm_buffer() but it's
+// probably not worth the extra complexity.
+uint8_t g_pwm_buffer[DRIVER_COUNT][144];
+bool g_pwm_buffer_update_required = false;
+
+uint8_t g_led_control_registers[DRIVER_COUNT][18] = { { 0 }, { 0 } };
+bool g_led_control_registers_update_required = false;
+
+// This is the bit pattern in the LED control registers
+// (for matrix A, add one to register for matrix B)
+//
+//  reg -  b7  b6  b5  b4  b3  b2  b1  b0
+// 0x00 - R08,R07,R06,R05,R04,R03,R02,R01
+// 0x02 - G08,G07,G06,G05,G04,G03,G02,R00
+// 0x04 - B08,B07,B06,B05,B04,B03,G01,G00
+// 0x06 -  - , - , - , - , - ,B02,B01,B00
+// 0x08 -  - , - , - , - , - , - , - , -
+// 0x0A - B17,B16,B15, - , - , - , - , -
+// 0x0C - G17,G16,B14,B13,B12,B11,B10,B09
+// 0x0E - R17,G15,G14,G13,G12,G11,G10,G09
+// 0x10 - R16,R15,R14,R13,R12,R11,R10,R09
+
+
+void IS31_write_register( uint8_t addr, uint8_t reg, uint8_t data )
+{
+    g_twi_transfer_buffer[0] = reg;
+    g_twi_transfer_buffer[1] = data;
+
+  #if ISSI_PERSISTENCE > 0
+    for (uint8_t i = 0; i < ISSI_PERSISTENCE; i++) {
+      if (i2c_transmit(addr << 1, g_twi_transfer_buffer, 2, ISSI_TIMEOUT) == 0)
+        break;
+    }
+  #else
+    i2c_transmit(addr << 1, g_twi_transfer_buffer, 2, ISSI_TIMEOUT);
+  #endif
+}
+
+void IS31_write_pwm_buffer( uint8_t addr, uint8_t *pwm_buffer )
+{
+    // assumes bank is already selected
+
+    // transmit PWM registers in 9 transfers of 16 bytes
+    // g_twi_transfer_buffer[] is 20 bytes
+
+    // iterate over the pwm_buffer contents at 16 byte intervals
+    for ( int i = 0; i < 144; i += 16 ) {
+        // set the first register, e.g. 0x24, 0x34, 0x44, etc.
+        g_twi_transfer_buffer[0] = 0x24 + i;
+        // copy the data from i to i+15
+        // device will auto-increment register for data after the first byte
+        // thus this sets registers 0x24-0x33, 0x34-0x43, etc. in one transfer
+        for ( int j = 0; j < 16; j++ ) {
+            g_twi_transfer_buffer[1 + j] = pwm_buffer[i + j];
+        }
+
+    #if ISSI_PERSISTENCE > 0
+      for (uint8_t i = 0; i < ISSI_PERSISTENCE; i++) {
+        if (i2c_transmit(addr << 1, g_twi_transfer_buffer, 17, ISSI_TIMEOUT) == 0)
+          break;
+      }
+    #else
+      i2c_transmit(addr << 1, g_twi_transfer_buffer, 17, ISSI_TIMEOUT);
+    #endif
+    }
+}
+
+void IS31_init( uint8_t addr )
+{
+    // In order to avoid the LEDs being driven with garbage data
+    // in the LED driver's PWM registers, first enable software shutdown,
+    // then set up the mode and other settings, clear the PWM registers,
+    // then disable software shutdown.
+
+    // select "function register" bank
+    IS31_write_register( addr, ISSI_COMMANDREGISTER, ISSI_BANK_FUNCTIONREG );
+
+    // enable software shutdown
+    IS31_write_register( addr, ISSI_REG_SHUTDOWN, 0x00 );
+    // this delay was copied from other drivers, might not be needed
+    #ifdef __AVR__
+    _delay_ms( 10 );
+    #else
+    wait_ms(10);
+    #endif
+
+    // picture mode
+    IS31_write_register( addr, ISSI_REG_CONFIG, ISSI_REG_CONFIG_PICTUREMODE );
+    // display frame 0
+    IS31_write_register( addr, ISSI_REG_PICTUREFRAME, 0x00 );
+    // audio sync off
+    IS31_write_register( addr, ISSI_REG_AUDIOSYNC, 0x00 );
+
+    // select bank 0
+    IS31_write_register( addr, ISSI_COMMANDREGISTER, 0 );
+
+    // turn off all LEDs in the LED control register
+    for ( int i = 0x00; i <= 0x11; i++ )
+    {
+        IS31_write_register( addr, i, 0x00 );
+    }
+
+    // turn off all LEDs in the blink control register (not really needed)
+    for ( int i = 0x12; i <= 0x23; i++ )
+    {
+        IS31_write_register( addr, i, 0x00 );
+    }
+
+    // set PWM on all LEDs to 0
+    for ( int i = 0x24; i <= 0xB3; i++ )
+    {
+        IS31_write_register( addr, i, 0x00 );
+    }
+
+    // select "function register" bank
+    IS31_write_register( addr, ISSI_COMMANDREGISTER, ISSI_BANK_FUNCTIONREG );
+
+    // disable software shutdown
+    IS31_write_register( addr, ISSI_REG_SHUTDOWN, 0x01 );
+
+    // select bank 0 and leave it selected.
+    // most usage after initialization is just writing PWM buffers in bank 0
+    // as there's not much point in double-buffering
+    IS31_write_register( addr, ISSI_COMMANDREGISTER, 0 );
+
+}
+
+void IS31_set_color( int index, uint8_t red, uint8_t green, uint8_t blue )
+{
+    if ( index >= 0 && index < DRIVER_LED_TOTAL ) {
+        is31_led led = g_is31_leds[index];
+
+        // Subtract 0x24 to get the second index of g_pwm_buffer
+        g_pwm_buffer[led.driver][led.r - 0x24] = red;
+        g_pwm_buffer[led.driver][led.g - 0x24] = green;
+        g_pwm_buffer[led.driver][led.b - 0x24] = blue;
+        g_pwm_buffer_update_required = true;
+    }
+}
+
+void IS31_set_color_all( uint8_t red, uint8_t green, uint8_t blue )
+{
+    for ( int i = 0; i < DRIVER_LED_TOTAL; i++ )
+    {
+        IS31_set_color( i, red, green, blue );
+    }
+}
+
+void IS31_set_led_control_register( uint8_t index, bool red, bool green, bool blue )
+{
+    is31_led led = g_is31_leds[index];
+
+  uint8_t control_register_r = (led.r - 0x24) / 8;
+  uint8_t control_register_g = (led.g - 0x24) / 8;
+  uint8_t control_register_b = (led.b - 0x24) / 8;
+  uint8_t bit_r = (led.r - 0x24) % 8;
+  uint8_t bit_g = (led.g - 0x24) % 8;
+  uint8_t bit_b = (led.b - 0x24) % 8;
+
+    if ( red ) {
+        g_led_control_registers[led.driver][control_register_r] |= (1 << bit_r);
+    } else {
+        g_led_control_registers[led.driver][control_register_r] &= ~(1 << bit_r);
+    }
+    if ( green ) {
+        g_led_control_registers[led.driver][control_register_g] |= (1 << bit_g);
+    } else {
+        g_led_control_registers[led.driver][control_register_g] &= ~(1 << bit_g);
+    }
+    if ( blue ) {
+        g_led_control_registers[led.driver][control_register_b] |= (1 << bit_b);
+    } else {
+        g_led_control_registers[led.driver][control_register_b] &= ~(1 << bit_b);
+    }
+
+    g_led_control_registers_update_required = true;
+
+}
+
+void IS31_update_pwm_buffers( uint8_t addr1, uint8_t addr2 )
+{
+    if ( g_pwm_buffer_update_required )
+    {
+        IS31_write_pwm_buffer( addr1, g_pwm_buffer[0] );
+        IS31_write_pwm_buffer( addr2, g_pwm_buffer[1] );
+    }
+    g_pwm_buffer_update_required = false;
+}
+
+void IS31_update_led_control_registers( uint8_t addr1, uint8_t addr2 )
+{
+    if ( g_led_control_registers_update_required )
+    {
+        for ( int i=0; i<18; i++ )
+        {
+            IS31_write_register(addr1, i, g_led_control_registers[0][i] );
+            IS31_write_register(addr2, i, g_led_control_registers[1][i] );
+        }
+    }
+}
+

drivers/is31fl3731.h

@@ -23,7 +23,7 @@
 #include <stdbool.h>
 
 typedef struct is31_led {
-	uint8_t driver:2;
+  uint8_t driver:2;
   uint8_t r;
   uint8_t g;
   uint8_t b;
@@ -31,21 +31,21 @@ typedef struct is31_led {
 
 extern const is31_led g_is31_leds[DRIVER_LED_TOTAL];
 
-void IS31FL3731_init( uint8_t addr );
-void IS31FL3731_write_register( uint8_t addr, uint8_t reg, uint8_t data );
-void IS31FL3731_write_pwm_buffer( uint8_t addr, uint8_t *pwm_buffer );
+void IS31_init( uint8_t addr );
+void IS31_write_register( uint8_t addr, uint8_t reg, uint8_t data );
+void IS31_write_pwm_buffer( uint8_t addr, uint8_t *pwm_buffer );
 
-void IS31FL3731_set_color( int index, uint8_t red, uint8_t green, uint8_t blue );
-void IS31FL3731_set_color_all( uint8_t red, uint8_t green, uint8_t blue );
+void IS31_set_color( int index, uint8_t red, uint8_t green, uint8_t blue );
+void IS31_set_color_all( uint8_t red, uint8_t green, uint8_t blue );
 
-void IS31FL3731_set_led_control_register( uint8_t index, bool red, bool green, bool blue );
+void IS31_set_led_control_register( uint8_t index, bool red, bool green, bool blue );
 
 // This should not be called from an interrupt
 // (eg. from a timer interrupt).
 // Call this while idle (in between matrix scans).
 // If the buffer is dirty, it will update the driver with the buffer.
-void IS31FL3731_update_pwm_buffers( uint8_t addr1, uint8_t addr2 );
-void IS31FL3731_update_led_control_registers( uint8_t addr1, uint8_t addr2 );
+void IS31_update_pwm_buffers( uint8_t addr1, uint8_t addr2 );
+void IS31_update_led_control_registers( uint8_t addr1, uint8_t addr2 );
 
 #define C1_1  0x24
 #define C1_2  0x25

keyboards/1up60rgb/readme.md

@@ -4,7 +4,7 @@ Firmware for custom keyboard PCB with 60% key layout.
 
 Keyboard Maintainer: [rempired](https://github.com/rempired)  
 Hardware Supported: 1upkeyboards 60% RGB  
-Hardware Availability: [1upkeyboards](https://1upkeyboards.com/rgb-underglow-1up-pcb.html)
+Hardware Availability: [1upkeyboards](https://www.1upkeyboards.com/shop/controllers/1up-rgb-underglow-pcb/)  
 
 Make example for this keyboard (after setting up your build environment):
 

keyboards/4x4/4x4.c

@@ -0,0 +1,29 @@
+
+#include "4x4.h"
+
+void matrix_init_kb(void) {
+	// put your keyboard start-up code here
+	// runs once when the firmware starts up
+
+	matrix_init_user();
+}
+
+void matrix_scan_kb(void) {
+	// put your looping keyboard code here
+	// runs every cycle (a lot)
+
+	matrix_scan_user();
+}
+
+bool process_record_kb(uint16_t keycode, keyrecord_t *record) {
+	// put your per-action keyboard code here
+	// runs for every action, just before processing by the firmware
+
+	return process_record_user(keycode, record);
+}
+
+void led_set_kb(uint8_t usb_led) {
+	// put your keyboard LED indicator (ex: Caps Lock LED) toggling code here
+
+	led_set_user(usb_led);
+}

keyboards/4x4/4x4.h

@@ -0,0 +1,62 @@
+
+#ifndef FOURX4_H
+#define FOURX4_H
+
+#include "quantum.h"
+#define ___ KC_NO
+
+// This a shortcut to help you visually see your layout.
+// The first section contains all of the arguments
+// The second converts the arguments into a two-dimensional array
+
+#define LAYOUT_ortho_4x4( \
+    K00, K01, K02, K03, \
+    K10, K11, K12, K13, \
+    K20, K21, K22, K23, \
+    K30, K31, K32, K33 \
+) \
+{ \
+    { K00, K01, K02, K03, ___, ___, ___, ___, ___, ___, ___, ___, ___, ___, ___, ___}, \
+    { K10, K11, K12, K13, ___, ___, ___, ___, ___, ___, ___, ___, ___, ___, ___, ___}, \
+    { K20, K21, K22, K23, ___, ___, ___, ___, ___, ___, ___, ___, ___, ___, ___, ___}, \
+    { K30, K31, K32, K33, ___, ___, ___, ___, ___, ___, ___, ___, ___, ___, ___, ___} \
+}
+#define LAYOUT_ortho_4x8( \
+    K00, K01, K02, K03, K04, K05, K06, K07, \
+    K10, K11, K12, K13, K14, K15, K16, K17, \
+    K20, K21, K22, K23, K24, K25, K26, K27, \
+    K30, K31, K32, K33, K34, K35, K36, K37\
+) \
+{ \
+    { K00, K01, K02, K03, K04, K05, K06, K07, ___, ___, ___, ___, ___, ___, ___, ___}, \
+    { K10, K11, K12, K13, K14, K15, K16, K17, ___, ___, ___, ___, ___, ___, ___, ___}, \
+    { K20, K21, K22, K23, K24, K25, K26, K27, ___, ___, ___, ___, ___, ___, ___, ___}, \
+    { K30, K31, K32, K33, K34, K35, K35, K37, ___, ___, ___, ___, ___, ___, ___, ___} \
+}
+#define LAYOUT_ortho_4x12( \
+    K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0a, K0b, \
+    K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1a, K1b, \
+    K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2a, K2b, \
+    K30, K31, K32, K33, K34, K35, K36, K37, K38, K39, K3a, K3b  \
+) \
+{ \
+    { K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0a, K0b, ___, ___, ___, ___}, \
+    { K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1a, K1b, ___, ___, ___, ___}, \
+    { K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2a, K2b, ___, ___, ___, ___}, \
+    { K30, K31, K32, K33, K34, K35, K35, K37, K38, K39, K3a, K3b, ___, ___, ___, ___} \
+}
+
+#define LAYOUT_ortho_4x16( \
+    K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0a, K0b, K0c, K0d, K0e, K0f, \
+    K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1a, K1b, K1c, K1d, K1e, K1f, \
+    K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2a, K2b, K2c, K2d, K2e, K2f, \
+    K30, K31, K32, K33, K34, K35, K36, K37, K38, K39, K3a, K3b, K3c, K3d, K3e, K3f \
+) \
+{ \
+    { K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0a, K0b, K0c, K0d, K0e, K0f }, \
+    { K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1a, K1b, K1c, K1d, K1e, K1f }, \
+    { K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2a, K2b, K2c, K2d, K2e, K2f }, \
+    { K30, K31, K32, K33, K34, K35, K35, K37, K38, K39, K3a, K3b, K3c, K3d, K3e, K3f } \
+}
+
+#endif

keyboards/4x4/config.h

@@ -0,0 +1,202 @@
+
+
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0xFEED
+#define PRODUCT_ID      0x0A0C
+#define DEVICE_VER      0x4444
+#define MANUFACTURER    di0ib
+#define PRODUCT         The 4x4 Keyboard
+#define DESCRIPTION     A modular compact keyboard
+
+/* key matrix size */
+#define MATRIX_ROWS 4
+#define MATRIX_COLS 16
+
+/*
+ * Keyboard Matrix Assignments
+ *
+ * Change this to how you wired your keyboard
+ * COLS: AVR pins used for columns, left to right
+ * ROWS: AVR pins used for rows, top to bottom
+ * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
+ *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
+ *
+*/
+#define MATRIX_ROW_PINS { B2, D1, D0, D4 }
+#define MATRIX_COL_PINS { C6, D7, E6, B4, B5, B6, B7, D6, F7, F6, F5, F4, F1, F0, B3, B1 }
+#define UNUSED_PINS
+
+
+/* COL2ROW, ROW2COL, or CUSTOM_MATRIX */
+#define DIODE_DIRECTION COL2ROW
+
+// #define BACKLIGHT_PIN C7
+// #define BACKLIGHT_BREATHING
+// #define BACKLIGHT_LEVELS 3
+
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCING_DELAY 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/* If defined, GRAVE_ESC will always act as ESC when CTRL is held.
+ * This is userful for the Windows task manager shortcut (ctrl+shift+esc).
+ */
+// #define GRAVE_ESC_CTRL_OVERRIDE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/* key combination for magic key command */
+#define IS_COMMAND() ( \
+    keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
+)
+
+/* control how magic key switches layers */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
+
+/* override magic key keymap */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
+//#define MAGIC_KEY_HELP1          H
+//#define MAGIC_KEY_HELP2          SLASH
+//#define MAGIC_KEY_DEBUG          D
+//#define MAGIC_KEY_DEBUG_MATRIX   X
+//#define MAGIC_KEY_DEBUG_KBD      K
+//#define MAGIC_KEY_DEBUG_MOUSE    M
+//#define MAGIC_KEY_VERSION        V
+//#define MAGIC_KEY_STATUS         S
+//#define MAGIC_KEY_CONSOLE        C
+//#define MAGIC_KEY_LAYER0_ALT1    ESC
+//#define MAGIC_KEY_LAYER0_ALT2    GRAVE
+//#define MAGIC_KEY_LAYER0         0
+//#define MAGIC_KEY_LAYER1         1
+//#define MAGIC_KEY_LAYER2         2
+//#define MAGIC_KEY_LAYER3         3
+//#define MAGIC_KEY_LAYER4         4
+//#define MAGIC_KEY_LAYER5         5
+//#define MAGIC_KEY_LAYER6         6
+//#define MAGIC_KEY_LAYER7         7
+//#define MAGIC_KEY_LAYER8         8
+//#define MAGIC_KEY_LAYER9         9
+//#define MAGIC_KEY_BOOTLOADER     PAUSE
+//#define MAGIC_KEY_LOCK           CAPS
+//#define MAGIC_KEY_EEPROM         E
+//#define MAGIC_KEY_NKRO           N
+//#define MAGIC_KEY_SLEEP_LED      Z
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+/*
+ * MIDI options
+ */
+
+/* Prevent use of disabled MIDI features in the keymap */
+//#define MIDI_ENABLE_STRICT 1
+
+/* enable basic MIDI features:
+   - MIDI notes can be sent when in Music mode is on
+*/
+//#define MIDI_BASIC
+
+/* enable advanced MIDI features:
+   - MIDI notes can be added to the keymap
+   - Octave shift and transpose
+   - Virtual sustain, portamento, and modulation wheel
+   - etc.
+*/
+//#define MIDI_ADVANCED
+
+/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
+//#define MIDI_TONE_KEYCODE_OCTAVES 1
+
+/*
+ * HD44780 LCD Display Configuration
+ */
+/*
+#define LCD_LINES           2     //< number of visible lines of the display
+#define LCD_DISP_LENGTH    16     //< visibles characters per line of the display
+
+#define LCD_IO_MODE      1            //< 0: memory mapped mode, 1: IO port mode
+
+#if LCD_IO_MODE
+#define LCD_PORT         PORTB        //< port for the LCD lines
+#define LCD_DATA0_PORT   LCD_PORT     //< port for 4bit data bit 0
+#define LCD_DATA1_PORT   LCD_PORT     //< port for 4bit data bit 1
+#define LCD_DATA2_PORT   LCD_PORT     //< port for 4bit data bit 2
+#define LCD_DATA3_PORT   LCD_PORT     //< port for 4bit data bit 3
+#define LCD_DATA0_PIN    4            //< pin for 4bit data bit 0
+#define LCD_DATA1_PIN    5            //< pin for 4bit data bit 1
+#define LCD_DATA2_PIN    6            //< pin for 4bit data bit 2
+#define LCD_DATA3_PIN    7            //< pin for 4bit data bit 3
+#define LCD_RS_PORT      LCD_PORT     //< port for RS line
+#define LCD_RS_PIN       3            //< pin  for RS line
+#define LCD_RW_PORT      LCD_PORT     //< port for RW line
+#define LCD_RW_PIN       2            //< pin  for RW line
+#define LCD_E_PORT       LCD_PORT     //< port for Enable line
+#define LCD_E_PIN        1            //< pin  for Enable line
+#endif
+*/
+

keyboards/4x4/keymaps/default/config.h

@@ -0,0 +1,5 @@
+
+
+#pragma once
+
+// place overrides here

keyboards/4x4/keymaps/default/keymap.c

@@ -0,0 +1,124 @@
+
+#include QMK_KEYBOARD_H
+
+#define PAD 0
+#define _QW 1
+#define NUM 2
+#define DIR 3
+
+// Readability keycodes
+#define _______ KC_TRNS
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+/* Single 4x4 board only
+ * .-----------------------------------.
+ * |   7    |   8    |   9    |   /    |
+ * |--------+--------+--------+--------|
+ * |   4    |   5    |   6    |   *    |
+ * |--------+--------+--------+--------|
+ * |   1    |   2    |   3    |   -    |
+ * |--------+--------+--------+--------|
+ * |   0    | QWERTY |   .    |   +    |
+ * '-----------------------------------'
+ */
+
+  [PAD] = LAYOUT_ortho_4x4(
+  KC_KP_7, KC_KP_8, KC_KP_9,   KC_PSLS,
+  KC_KP_4, KC_KP_5, KC_KP_6,   KC_PAST,
+  KC_KP_1, KC_KP_2, KC_KP_3,   KC_PMNS,
+  KC_KP_0, DF(_QW), KC_KP_DOT, KC_PPLS
+  ),
+
+/* QWERTY
+ * .-----------------------------------------------------------------------------------------------------------------------------------------------.
+ * | ESC    | Q      | W      | E      | R      | T      | Y      | U      | I      | O      | P      | BACKSP |   7    |   8    |   9    |   /    |
+ * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------|
+ * | TAB    | A      | S      | D      | F      | G      | H      | J      | K      | L      | ;      | '      |   4    |   5    |   6    |   *    |
+ * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------|
+ * | SHIFT  | Z      | X      | C      | V      | B      | N      | M      | ,      | .      | /      | ENT/SFT|   1    |   2    |   3    |   -    |
+ * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------|
+ * | LCTRL  | LGUI   | ALT    | ALT    | NUM    | SHIFT  | SPACE  | DIR    | RGUI   | RALT   | DEL    | CTRL   |   0    |   0    |   .    |   +    |
+ * '-----------------------------------------------------------------------------------------------------------------------------------------------'
+ */
+
+  [_QW] = LAYOUT_ortho_4x16(
+  KC_ESC,  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_BSPC, KC_KP_7, KC_KP_8, KC_KP_9, KC_PSLS,
+  KC_TAB,  KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN, KC_QUOT, KC_KP_4, KC_KP_5, KC_KP_6, KC_PAST,
+  KC_LSFT, KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH, SFT_T(KC_ENT), KC_KP_1, KC_KP_2, KC_KP_3, KC_PMNS,
+  KC_LCTL, KC_LGUI, KC_LALT, KC_LALT, MO(NUM), KC_LSFT, KC_SPC,  MO(DIR), KC_RGUI, KC_RALT, KC_DEL,  KC_RCTL, KC_KP_0, KC_KP_0, KC_KP_DOT, KC_PPLS
+  ),
+
+/* NUMBERS
+ * .-----------------------------------------------------------------------------------------------------------------------------------------------.
+ * |        | F1     | F2     | F3     | F4     | F5     | F6     | F7     | F8     | F9     | F10    | NUMLOCK|   /    |   *    |   -    |        |
+ * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------|
+ * |    `   | 1      | 2      | 3      | 4      | 5      | 6      | 7      | 8      | 9      | 0      |        |        |        |   +    |        |
+ * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------|
+ * |        | F11    | F12    |        |        |        | ENTER  | SHIFT  | RGUI   | ./ALT  | BKSC   |        |        |        | ENTER  |        |
+ * |        |        |        |        |        |        |        |        |        |        |CTRLhold|		   |        |        |        |        |
+ * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------|        |
+ * |        |        |        |        |        |        | ENTER  | SHIFT  |        |        |        |        |        |        |        |        |
+ * '-----------------------------------------------------------------------------------------------------------------------------------------------'
+ */
+
+  [NUM] = LAYOUT_ortho_4x16(
+  _______, KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,   KC_NLCK, KC_PSLS, KC_PAST, KC_PMNS, _______,
+  KC_GRV,  KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,    KC_9,    KC_0,     _______, _______, _______, KC_PPLS, _______,
+  _______, KC_F11,  KC_F12,  KC_TRNS, KC_TRNS, KC_TRNS, KC_ENT,  KC_RSFT, KC_RGUI, ALT_T(KC_DOT), CTL_T(KC_BSPC), _______, _______, _______, KC_PENT, _______,
+  _______, _______, _______, _______, _______, _______, KC_ENT,  KC_RSFT, _______, _______, _______,  _______, _______, _______, _______, _______
+  ),
+
+/* DIRECTIONS
+ * .-----------------------------------------------------------------------------------------------------------------------------------------------.
+ * | RESET  | TAB    |   up   |        | INS    | CTRL   | SHIFT  | PgUp   | Home   |   -    |   =    |  DEL   |        |        |        |        |
+ * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------|
+ * | CAPSLK | left   |  down  | right  | PrScr  | SHIFT  | CTRL   | PgDn   | End    |   [    |   ]    |   \    |        |        |        |        |
+ * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------|
+ * |        | P-Brk  |        |        |        |        |        |        | RGUI   | ALT    |        |        |        |        |        |        |
+ * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------|
+ * | KEYPAD |        |        |        |        |        |        |        |        |        |        |        |        |        |        |        |
+ * '-----------------------------------------------------------------------------------------------------------------------------------------------'
+ */
+
+  [DIR] = LAYOUT_ortho_4x16(
+  RESET,   KC_TAB,  KC_UP,   _______, KC_INS,  KC_LCTL, KC_LSFT, KC_PGUP, KC_HOME, KC_MINS, KC_EQL,  KC_DEL,  _______, _______, _______, _______,
+  KC_CAPS, KC_LEFT, KC_DOWN, KC_RGHT, KC_PSCR, KC_LSFT, KC_LCTL, KC_PGDN, KC_END,  KC_LBRC, KC_RBRC, KC_BSLS, _______, _______, _______, _______,
+  _______, KC_PAUS, _______, _______, _______, _______, _______, _______, KC_RGUI, KC_RALT, _______, _______, _______, _______, _______, _______,
+  DF(PAD), _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______
+  ),
+
+};
+
+
+const uint16_t PROGMEM fn_actions[] = {
+
+};
+
+
+const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) {
+  keyevent_t event = record->event;
+    (void)event;
+
+  switch (id) {
+
+  }
+  return MACRO_NONE;
+}
+
+
+void matrix_init_user(void) {
+
+}
+
+void matrix_scan_user(void) {
+
+}
+
+bool process_record_user(uint16_t keycode, keyrecord_t *record) {
+  return true;
+}
+
+void led_set_user(uint8_t usb_led) {
+
+}

keyboards/4x4/readme.md

@@ -0,0 +1,23 @@
+# 4x4
+
+![4x4](https://2.bp.blogspot.com/-xRZOpwlTT4c/WlOwRIVAecI/AAAAAAACKo4/d75juHTX2W0Nrch7NigssMbagvl3I4w_ACEwYBhgL/s1600/e.jpg)
+===
+
+**Modular keypad/keyboard**  
+The basic unit is a 4x4 matrix with 16 keys. Up to 4 of these can be connected to each other side by side.  
+4x4, 4x8, 4x12 and 4x16 are possible.  
+There are pads for header pins on each side that complete the circuits from board to board. These can be permanently connected with solder bridges or temporarily with pin headers and shunt jumpers.  
+**_All configurations are powered by a SINGLE Arduino Micro or clone (NOT a Pro Micro)._**  
+
+* [The original TMK firmware](https://github.com/di0ib/tmk_keyboard/tree/master/keyboard/4x4)
+
+Keyboard Maintainer: QMK Community  
+Hardware Supported: 4x4 PCB  
+Hardware Availability: [4x4x4x4x4 project on 40% Keyboards](http://www.40percent.club/2018/01/4x4x4x4x4.html)  
+
+Make example for this keyboard (after setting up your build environment):  
+
+    make 4x4:default
+
+See [build environment setup](https://docs.qmk.fm/build_environment_setup.html) then the [make instructions](https://docs.qmk.fm/make_instructions.html) for more information.  
+First pass at adding support for the 4x4 keyboard. Compiles but completely untested. Intended to kick-start development.  

keyboards/4x4/rules.mk

@@ -0,0 +1,74 @@
+# MCU name
+#MCU = at90usb1286
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+# Bootloader
+#     This definition is optional, and if your keyboard supports multiple bootloaders of
+#     different sizes, comment this out, and the correct address will be loaded 
+#     automatically (+60). See bootloader.mk for all options.
+BOOTLOADER = caterina
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE = no      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = yes        # Console for debug(+400)
+COMMAND_ENABLE = yes        # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE = no            # USB Nkey Rollover
+BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality on B7 by default
+MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no           # Audio output on port C6
+FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
+HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)
+
+LAYOUT = ortho_4x4  ortho_4x8  ortho_4x12  ortho_4x16 

keyboards/atreus/keymaps/dvorak_42_key/keymap.c

@@ -5,15 +5,9 @@
 #define BASE      0
 #define KEYNAV    1
 #define KEYSEL    2
-#define MOUSE     3
-#define COMBINED  4
-#define BROWSER_CONTROL 5
+#define COMBINED  3
+#define BROWSER_CONTROL 4
 
-// macros
-#define MOUSE_TOGGLE 1
-#define MOUSE_LOCK 2
-
-static bool mouse_lock = false;
 
 enum custom_keycodes {
   PLACEHOLDER = SAFE_RANGE, // can always be here
@@ -63,18 +57,11 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
     KC_TRNS, KC_TILD, KC_GRAVE,    KC_CIRC,     KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,  KC_0, KC_DOT, KC_PIPE, KC_BSLS
   ),
 
-  [MOUSE] = LAYOUT(
-    KC_TRNS,      KC_PGUP,       KC_MS_WH_UP,   KC_UP,        KC_TRNS,                   KC_UP,     KC_HOME,            KC_MS_U,      KC_END,     KC_MS_WH_UP,
-    KC_MS_ACCEL0, KC_PGDN,       KC_MS_WH_DOWN, KC_DOWN,      KC_TRNS,                   KC_DOWN,   KC_MS_L,            KC_MS_D,      KC_MS_R,    KC_MS_WH_DOWN,
-    KC_TRNS,      KC_TRNS,       KC_TRNS,       KC_TRNS,      KC_TRNS,                   MEH(KC_X), MEH(KC_Y),          MEH(KC_Z),    KC_F5,      RCTL(KC_W),
-    KC_TRNS,      M(MOUSE_LOCK), KC_TRNS,       KC_MS_ACCEL0, KC_TRNS, KC_BTN3, KC_BTN1, KC_BTN2,   RSFT(RCTL(KC_TAB)), RCTL(KC_TAB), RCTL(KC_T), LALT(KC_LEFT)
-  ),
-
   [BROWSER_CONTROL] = LAYOUT(
-    KC_TRNS, KC_BTN3, KC_MS_U, KC_BTN1, KC_BTN2,                      KC_UP,      KC_PGUP,            KC_PGDN,      KC_MS_WH_UP,   KC_TRNS,
-    KC_TRNS, KC_MS_L, KC_MS_D, KC_MS_R, KC_TRNS,                      KC_DOWN,    RSFT(RCTL(KC_TAB)), RCTL(KC_TAB), KC_MS_WH_DOWN, LALT(KC_LEFT),
-    KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,                      KC_TRNS,    RCTL(KC_1),         RCTL(KC_9),   KC_F6,         KC_F5,
-    KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, RCTL(KC_W), RCTL(KC_T), RSFT(RCTL(KC_TAB)), KC_TRNS,      KC_TRNS,       KC_TRNS
+    MEH(KC_0), KC_BTN3,   KC_MS_U,   KC_BTN1,   KC_BTN2,                      KC_UP,      KC_PGUP,            KC_PGDN,      KC_MS_WH_UP,   MEH(KC_9),
+    MEH(KC_1), KC_MS_L,   KC_MS_D,   KC_MS_R,   MEH(KC_6),                    KC_DOWN,    RSFT(RCTL(KC_TAB)), RCTL(KC_TAB), KC_MS_WH_DOWN, LALT(KC_LEFT),
+    MEH(KC_2), MEH(KC_3), MEH(KC_4), MEH(KC_5), MEH(KC_7),                    MEH(KC_8),  RCTL(KC_1),         RCTL(KC_9),   KC_F6,         KC_F5,
+    KC_TRNS,   KC_TRNS,   KC_TRNS,   KC_TRNS,   KC_TRNS, KC_TRNS, RCTL(KC_W), RCTL(KC_T), RSFT(RCTL(KC_TAB)), KC_TRNS,      KC_TRNS,       KC_TRNS
   ),
 };
 
@@ -116,30 +103,3 @@ bool process_record_user(uint16_t keycode, keyrecord_t *record) {
   return true;
 }
 
-const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
-{
-  // MACRODOWN only works in this function
-      switch(id) {
-		case MOUSE_TOGGLE:
-            if (record->event.pressed) {
-				layer_on(MOUSE);
-            } else {
-				if(!mouse_lock)
-					layer_off(MOUSE);
-			}
-			break;
-		case MOUSE_LOCK:
-			if (record->event.pressed)
-			{
-				if(mouse_lock)
-				{
-					mouse_lock = false;
-					layer_off(MOUSE);
-				}
-				else
-					mouse_lock = true;
-			}
-			break;
-      }
-    return MACRO_NONE;
-};

keyboards/bfake/readme.md

@@ -11,4 +11,34 @@ Make example for this keyboard (after setting up your build environment):
 
     make bfake:default
 
-See [build environment setup](https://docs.qmk.fm/build_environment_setup.html) then the [make instructions](https://docs.qmk.fm/make_instructions.html) for more information.
+Flashing
+
+ps2avr(GB) boards use an atmega32a microcontroller and a different bootloader. It is not flashable using the regular QMK methods. 
+
+Windows: 
+1. Download [HIDBootFlash](http://vusb.wikidot.com/project:hidbootflash).
+2. Place your keyboard into reset. 
+3. Press the `Find Device` button and ensure that your keyboard is found.
+4. Press the `Open .hex File` button and locate the `.hex` file you created.
+5. Press the `Flash Device` button and wait for the process to complete. 
+
+macOS:
+1. Install homebrew by typing the following:   
+    ```
+    /usr/bin/ruby -e "$(curl -fsSL https://raw.githubusercontent.com/Homebrew/install/master/install)"
+    ```
+2. Install `crosspack-avr`.  
+    ```
+    brew cask install crosspack-avr
+    ```
+3. Install the following packages:
+    ```
+    brew install python
+    brew install pyusb
+    brew install --HEAD`https://raw.githubusercontent.com/robertgzr/homebrew-tap/master/bootloadhid.rb
+
+4. Place your keyboard into reset. 
+5. Flash the board by typing `bootloadHID -r` followed by the path to your `.hex` file. 
+
+
+See [build environment setup](https://docs.qmk.fm/build_environment_setup.html) then the [make instructions](https://docs.qmk.fm/make_instructions.html) for more information.

keyboards/blockey/blockey.h

@@ -0,0 +1,45 @@
+/* Copyright 2018 Eucalyn
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#ifndef BLOCKEY_H
+#define BLOCKEY_H
+
+#include "quantum.h"
+
+// This a shortcut to help you visually see your layout.
+// The following is an example using the Planck MIT layout
+// The first section contains all of the arguments
+// The second converts the arguments into a two-dimensional array
+#define LAYOUT( \
+    k01, k02, k03, k04, k05, k06, k07, k08, k09, k10, k11, k12, k13, k14, \
+    k15, k16, k17, k18, k19, k20, k21, k22, k23, k24, k25, k26, k27, k28, \
+    k29, k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k40, k41, \
+    k42, k43, k44, k45, k46, k47, k48, k49, k50, k51, k52, k53, k54, \
+    k55, k56, k57, k58, k59, k60, k61, k62 \
+) \
+{ \
+    { k01, k02, k03, k04, k05, k06, k07 }, \
+    { k15, k16, k17, k18, k19, k20, k21 }, \
+    { k29, k30, k31, k32, k33, k34, k35 }, \
+    { k42, k43, k44, k45, k46, k47, k48 }, \
+    { k55, k56, k57, k58, KC_NO, KC_NO, k59 }, \
+    { k08, k09, k10, k11, k12, k13, k14 }, \
+    { k22, k23, k24, k25, k26, k27, k28 }, \
+    { k36, k37, k38, k39, k40, k41, KC_NO }, \
+    { k49, k50, k51, k52, k53, k54, KC_NO }, \
+    { KC_NO, KC_NO, KC_NO, k60, k61, k62, KC_NO}, \
+}
+
+#endif

keyboards/blockey/config.h

@@ -0,0 +1,199 @@
+/*
+Copyright 2018 Eucalyn
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#ifndef CONFIG_H
+#define CONFIG_H
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0xFEED
+#define PRODUCT_ID      0x0000
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    Eucalyn
+#define PRODUCT         Blockey
+#define DESCRIPTION     A custom keyboard
+
+/* key matrix size */
+#define MATRIX_ROWS 10
+#define MATRIX_COLS 7
+
+/*
+ * Keyboard Matrix Assignments
+ *
+ * Change this to how you wired your keyboard
+ * COLS: AVR pins used for columns, left to right
+ * ROWS: AVR pins used for rows, top to bottom
+ * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
+ *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
+ *
+*/
+#define MATRIX_ROW_PINS { D3, D1, D4, E6, B5, D2, F6, B3, B2, B6 }
+#define MATRIX_COL_PINS { D0, B4, C6, D7, F4, F5, F7 }
+#define UNUSED_PINS
+
+/* COL2ROW, ROW2COL, or CUSTOM_MATRIX */
+#define DIODE_DIRECTION COL2ROW
+
+/* ws2812 RGB LED */
+#define RGB_DI_PIN B1
+#define RGBLIGHT_TIMER
+#define RGBLED_NUM 4
+#define ws2812_PORTREG  PORTB
+#define ws2812_DDRREG   DDRB
+
+#define RGBLIGHT_HUE_STEP 10
+#define RGBLIGHT_SAT_STEP 17
+
+#define RGBLIGHT_ANIMATIONS
+
+
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCING_DELAY 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/* If defined, GRAVE_ESC will always act as ESC when CTRL is held.
+ * This is userful for the Windows task manager shortcut (ctrl+shift+esc).
+ */
+// #define GRAVE_ESC_CTRL_OVERRIDE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/* key combination for magic key command */
+#define IS_COMMAND() ( \
+    keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
+)
+
+/* control how magic key switches layers */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
+
+/* override magic key keymap */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
+//#define MAGIC_KEY_HELP1          H
+//#define MAGIC_KEY_HELP2          SLASH
+//#define MAGIC_KEY_DEBUG          D
+//#define MAGIC_KEY_DEBUG_MATRIX   X
+//#define MAGIC_KEY_DEBUG_KBD      K
+//#define MAGIC_KEY_DEBUG_MOUSE    M
+//#define MAGIC_KEY_VERSION        V
+//#define MAGIC_KEY_STATUS         S
+//#define MAGIC_KEY_CONSOLE        C
+//#define MAGIC_KEY_LAYER0_ALT1    ESC
+//#define MAGIC_KEY_LAYER0_ALT2    GRAVE
+//#define MAGIC_KEY_LAYER0         0
+//#define MAGIC_KEY_LAYER1         1
+//#define MAGIC_KEY_LAYER2         2
+//#define MAGIC_KEY_LAYER3         3
+//#define MAGIC_KEY_LAYER4         4
+//#define MAGIC_KEY_LAYER5         5
+//#define MAGIC_KEY_LAYER6         6
+//#define MAGIC_KEY_LAYER7         7
+//#define MAGIC_KEY_LAYER8         8
+//#define MAGIC_KEY_LAYER9         9
+//#define MAGIC_KEY_BOOTLOADER     PAUSE
+//#define MAGIC_KEY_LOCK           CAPS
+//#define MAGIC_KEY_EEPROM         E
+//#define MAGIC_KEY_NKRO           N
+//#define MAGIC_KEY_SLEEP_LED      Z
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+/*
+ * MIDI options
+ */
+
+/* Prevent use of disabled MIDI features in the keymap */
+//#define MIDI_ENABLE_STRICT 1
+
+/* enable basic MIDI features:
+   - MIDI notes can be sent when in Music mode is on
+*/
+//#define MIDI_BASIC
+
+/* enable advanced MIDI features:
+   - MIDI notes can be added to the keymap
+   - Octave shift and transpose
+   - Virtual sustain, portamento, and modulation wheel
+   - etc.
+*/
+//#define MIDI_ADVANCED
+
+/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
+//#define MIDI_TONE_KEYCODE_OCTAVES 1
+
+#endif

keyboards/blockey/keymaps/default/keymap.c

@@ -0,0 +1,80 @@
+/* Copyright 2018 Eucalyn
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include QMK_KEYBOARD_H
+
+#ifdef RGBLIGHT_ENABLE
+//Following line allows macro to read current RGB settings
+extern rgblight_config_t rgblight_config;
+#endif
+
+// Fillers to make layering more clear
+#define _______ KC_TRNS
+#define XXXXXXX KC_NO
+
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+  [0] = LAYOUT(
+    KC_GRV, KC_1,   KC_2,   KC_3,   KC_4,   KC_5,   KC_6,   KC_7,   KC_8,   KC_9,   KC_0,   KC_MINS,KC_EQL, KC_BSPC, \
+    KC_TAB, KC_Q,   KC_W,   KC_E,   KC_R,   KC_T,   KC_Y,   KC_U,   KC_I,   KC_O,   KC_P,   KC_LBRC,KC_RBRC,KC_BSLS, \
+    KC_LCTL,KC_A,   KC_S,   KC_D,   KC_F,   KC_G,   KC_H,   KC_J,   KC_K,   KC_L,   KC_SCLN,KC_QUOT,KC_ENT, \
+    KC_LSFT,KC_Z,   KC_X,   KC_C,   KC_V,   KC_B,   KC_N,   KC_M,   KC_COMM,KC_DOT, KC_SLSH,KC_UP,  MO(1), \
+    KC_ESC, KC_CAPS,KC_LALT,KC_LGUI,KC_SPC,                                         KC_LEFT,KC_DOWN,KC_RGHT \
+  ),
+  [1] = LAYOUT(
+    _______,KC_F1,  KC_F2,  KC_F3,  KC_F4,  KC_F5,  KC_F6,  KC_F7,  KC_F8,  KC_F9,  KC_F10, KC_F11, KC_F12, _______, \
+    _______,RGB_TOG,RGB_HUI,RGB_SAI,RGB_VAI,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, \
+    _______,RGB_MOD,RGB_HUD,RGB_SAD,RGB_VAD,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,_______, \
+    _______,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,KC_PGUP,_______, \
+    _______,_______,_______,_______,_______,                                        KC_HOME,KC_PGDN,KC_END \
+  ),
+
+};
+
+const uint16_t PROGMEM fn_actions[] = {
+
+};
+
+const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
+{
+  // MACRODOWN only works in this function
+      switch(id) {
+        case 0:
+          if (record->event.pressed) {
+            register_code(KC_RSFT);
+          } else {
+            unregister_code(KC_RSFT);
+          }
+        break;
+      }
+    return MACRO_NONE;
+};
+
+
+void matrix_init_user(void) {
+
+}
+
+void matrix_scan_user(void) {
+
+}
+
+bool process_record_user(uint16_t keycode, keyrecord_t *record) {
+  return true;
+}
+
+void led_set_user(uint8_t usb_led) {
+
+}

keyboards/blockey/keymaps/eucalyn/keymap.c

@@ -0,0 +1,79 @@
+/* Copyright 2018 Eucalyn
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include QMK_KEYBOARD_H
+
+#ifdef RGBLIGHT_ENABLE
+//Following line allows macro to read current RGB settings
+extern rgblight_config_t rgblight_config;
+#endif
+
+// Fillers to make layering more clear
+#define _______ KC_TRNS
+#define XXXXXXX KC_NO
+
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+  [0] = LAYOUT(
+    KC_GRV, KC_1,   KC_2,   KC_3,   KC_4,   KC_5,   KC_6,   KC_7,   KC_8,   KC_9,   KC_0,   KC_MINS,KC_EQL, KC_BSPC, \
+    KC_TAB, KC_Q,   KC_W,   KC_COMM,KC_DOT, KC_SCLN,KC_M,   KC_R,   KC_D,   KC_Y,   KC_P,   KC_LBRC,KC_RBRC,KC_BSLS, \
+    KC_LCTL,KC_A,   KC_O,   KC_E,   KC_I,   KC_U,   KC_G,   KC_T,   KC_K,   KC_S,   KC_N,   KC_QUOT,KC_ENT, \
+    KC_LSFT,KC_Z,   KC_X,   KC_C,   KC_V,   KC_F,   KC_B,   KC_H,   KC_J,   KC_L,   KC_SLSH,KC_UP,  MO(1), \
+    KC_ESC, KC_CAPS,KC_LALT,KC_LGUI,KC_SPC,                                         KC_LEFT,KC_DOWN,KC_RGHT \
+  ),
+  [1] = LAYOUT(
+    _______,KC_F1,  KC_F2,  KC_F3,  KC_F4,  KC_F5,  KC_F6,  KC_F7,  KC_F8,  KC_F9,  KC_F10, KC_F11, KC_F12, _______, \
+    _______,RGB_TOG,RGB_HUI,RGB_SAI,RGB_VAI,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, \
+    _______,RGB_MOD,RGB_HUD,RGB_SAD,RGB_VAD,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,_______, \
+    _______,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,KC_PGUP,_______, \
+    _______,_______,_______,_______,_______,                                        KC_HOME,KC_PGDN,KC_END \
+  ),
+};
+
+const uint16_t PROGMEM fn_actions[] = {
+
+};
+
+const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
+{
+  // MACRODOWN only works in this function
+      switch(id) {
+        case 0:
+          if (record->event.pressed) {
+            register_code(KC_RSFT);
+          } else {
+            unregister_code(KC_RSFT);
+          }
+        break;
+      }
+    return MACRO_NONE;
+};
+
+
+void matrix_init_user(void) {
+
+}
+
+void matrix_scan_user(void) {
+
+}
+
+bool process_record_user(uint16_t keycode, keyrecord_t *record) {
+  return true;
+}
+
+void led_set_user(uint8_t usb_led) {
+
+}

keyboards/blockey/readme.md

@@ -0,0 +1,15 @@
+# BlocKey
+
+![BlocKey](https://imgur.com/a/6jAcrjr)
+
+A small keyboard.
+
+Keyboard Maintainer: [Eucalyn](https://github.com/eucalyn/) [@eucalyn_](https://twitter.com/eucalyn_)  
+Hardware Supported: BlocKey PCB, Pro Micro  
+Hardware Availability:
+
+Make example for this keyboard (after setting up your build environment):
+
+    make blockey:default
+
+See [build environment setup](https://docs.qmk.fm/build_environment_setup.html) then the [make instructions](https://docs.qmk.fm/make_instructions.html) for more information.

keyboards/blockey/rules.mk

@@ -0,0 +1,72 @@
+SRC += ws2812.c
+
+# MCU name
+#MCU = at90usb1286
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE = no      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = yes        # Console for debug(+400)
+COMMAND_ENABLE = yes        # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE = no            # USB Nkey Rollover
+BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality on B7 by default
+MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no           # Audio output on port C6
+FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
+
+RGBLIGHT_ENABLE = yes

keyboards/bmini/readme.md

@@ -11,4 +11,34 @@ Make example for this keyboard (after setting up your build environment):
 
     make bmini:default
 
-See [build environment setup](https://docs.qmk.fm/build_environment_setup.html) then the [make instructions](https://docs.qmk.fm/make_instructions.html) for more information.
+Flashing
+
+ps2avr(GB) boards use an atmega32a microcontroller and a different bootloader. It is not flashable using the regular QMK methods. 
+
+Windows: 
+1. Download [HIDBootFlash](http://vusb.wikidot.com/project:hidbootflash).
+2. Place your keyboard into reset. 
+3. Press the `Find Device` button and ensure that your keyboard is found.
+4. Press the `Open .hex File` button and locate the `.hex` file you created.
+5. Press the `Flash Device` button and wait for the process to complete. 
+
+macOS:
+1. Install homebrew by typing the following:   
+    ```
+    /usr/bin/ruby -e "$(curl -fsSL https://raw.githubusercontent.com/Homebrew/install/master/install)"
+    ```
+2. Install `crosspack-avr`.  
+    ```
+    brew cask install crosspack-avr
+    ```
+3. Install the following packages:
+    ```
+    brew install python
+    brew install pyusb
+    brew install --HEAD`https://raw.githubusercontent.com/robertgzr/homebrew-tap/master/bootloadhid.rb
+
+4. Place your keyboard into reset. 
+5. Flash the board by typing `bootloadHID -r` followed by the path to your `.hex` file. 
+
+
+See [build environment setup](https://docs.qmk.fm/build_environment_setup.html) then the [make instructions](https://docs.qmk.fm/make_instructions.html) for more information.

keyboards/canoe/readme.md

@@ -11,4 +11,34 @@ Make example for this keyboard (after setting up your build environment):
 
     make canoe:default
 
+Flashing
+
+ps2avr(GB) boards use an atmega32a microcontroller and a different bootloader. It is not flashable using the regular QMK methods. 
+
+Windows: 
+1. Download [HIDBootFlash](http://vusb.wikidot.com/project:hidbootflash).
+2. Place your keyboard into reset. 
+3. Press the `Find Device` button and ensure that your keyboard is found.
+4. Press the `Open .hex File` button and locate the `.hex` file you created.
+5. Press the `Flash Device` button and wait for the process to complete. 
+
+macOS:
+1. Install homebrew by typing the following:   
+    ```
+    /usr/bin/ruby -e "$(curl -fsSL https://raw.githubusercontent.com/Homebrew/install/master/install)"
+    ```
+2. Install `crosspack-avr`.  
+    ```
+    brew cask install crosspack-avr
+    ```
+3. Install the following packages:
+    ```
+    brew install python
+    brew install pyusb
+    brew install --HEAD`https://raw.githubusercontent.com/robertgzr/homebrew-tap/master/bootloadhid.rb
+
+4. Place your keyboard into reset. 
+5. Flash the board by typing `bootloadHID -r` followed by the path to your `.hex` file. 
+
+
 See [build environment setup](https://docs.qmk.fm/build_environment_setup.html) then the [make instructions](https://docs.qmk.fm/make_instructions.html) for more information.

keyboards/catch22/README.md

@@ -0,0 +1,17 @@
+# Catch 22 Budget Hotswap Macropad
+
+GB by /u/rockydbull run in July 2018, PCB designed with help from /u/Kilgarah.
+
+Designed to be a budget project board to enjoy hotswapping/switch testing/macro making fun. The board is controlled by a pro micro clone made famous by other projects like the lets split, iris, and nyquist and allows for full QMK implementation. Each Catch22 kit will contain:
+
+ * 2 pcbs (one to solder to and one to be a base)(green color)
+ * 1 pcb material switch plate( green color) with cut out for pcb mount cherry stabilizers
+ * 40 throughhole diodes (22 for the pcb and the remaining as extras in case you lose one and to use to make the pro micro removeable without desoldering)
+ * 22 Kailh hotswap sockets
+ * 1 smd reset button
+ * 1 dip socket to mount between the pcb and pro micro if you choose to make it removeable without desoldering
+ * 5 (12mm) m2 standoffs
+ * 10 m2 screws
+ * Genuine Cherry pcb mount 2u stabilizer
+ * 4 rubber bumpons
+ * Pro Micro is included in kit

keyboards/catch22/catch22.c

@@ -0,0 +1,18 @@
+/*
+Copyright 2018 QMK Community
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#include "catch22.h"

keyboards/catch22/catch22.h

@@ -0,0 +1,33 @@
+/*
+Copyright 2018 QMK Community
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+#pragma once
+
+#include "quantum.h"
+
+#define LAYOUT( \
+     K01, K02, K03, K04, \
+     K11, K12, K13, K14, \
+K20, K21, K22, K23, K24, \
+K30, K31, K32, K33, K34, \
+     K41, K42, K43, K44 \
+) { \
+  { KC_NO, K01, K02, K03, K04 },  \
+  { KC_NO, K11, K12, K13, K14 },  \
+  { K20,   K21, K22, K23, K24 },  \
+  { K30,   K31, K32, K33, K34 },  \
+  { KC_NO, K41, K42, K43, K44 },  \
+}

keyboards/catch22/config.h

@@ -0,0 +1,56 @@
+/*
+Copyright 2018 QMK Contributors
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0xFEED
+#define PRODUCT_ID      0xCA22
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    rockydbull
+#define PRODUCT         Catch22 Hotswap Macropad
+#define DESCRIPTION     Budget 22 Key Hotswap Macropad
+
+/* key matrix size */
+#define MATRIX_ROWS 5
+#define MATRIX_COLS 5
+
+/* key matrix pins */
+#define MATRIX_ROW_PINS { B6, B2, B3, B1, F7 }
+#define MATRIX_COL_PINS { B5, B4, E6, D7, C6 }
+#define UNUSED_PINS { }
+
+/* COL2ROW or ROW2COL */
+#define DIODE_DIRECTION COL2ROW
+
+/* Set 0 if debouncing isn't needed */
+#define DEBOUNCING_DELAY 50
+
+/* key combination for command */
+#define IS_COMMAND() ( \
+    false \
+)
+
+/* prevent stuck modifiers */
+#define PREVENT_STUCK_MODIFIERS
+
+#ifdef RGBLIGHT_ENABLE
+#define RGB_DI_PIN F6
+#define RGBLIGHT_ANIMATIONS
+#define RGBLED_NUM 6
+#endif

keyboards/catch22/info.json

@@ -0,0 +1,10 @@
+{
+    "keyboard_name": "catch22",
+    "width": 5,
+    "height": 5,
+    "layouts": {
+        "LAYOUT": {
+            "layout": [{"label":"A", "x":1, "y":0}, {"label":"B", "x":2, "y":0}, {"label":"C", "x":3, "y":0}, {"label":"D", "x":4, "y":0}, {"label":"E", "x":1, "y":1}, {"label":"F", "x":2, "y":1}, {"label":"G", "x":3, "y":1}, {"label":"H", "x":4, "y":1}, {"label":"I", "x":0, "y":2}, {"label":"J", "x":1, "y":2}, {"label":"K", "x":2, "y":2}, {"label":"L", "x":3, "y":2}, {"label":"M", "x":4, "y":2}, {"label":"1", "x":0, "y":3, "h":2}, {"label":"N", "x":1, "y":3}, {"label":"O", "x":2, "y":3}, {"label":"P", "x":3, "y":3}, {"label":"Q", "x":4, "y":3}, {"label":"R", "x":1, "y":4}, {"label":"S", "x":2, "y":4}, {"label":"T", "x":3, "y":4}, {"label":"U", "x":4, "y":4}]
+        }
+    }
+}

keyboards/catch22/keymaps/default/keymap.c

@@ -0,0 +1,31 @@
+#include QMK_KEYBOARD_H
+
+#define _BASE 0
+#define _FN   1
+
+#define _______ KC_TRNS
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+[_BASE] = LAYOUT( /* Base */
+           KC_NLCK, KC_PSLS,  KC_PAST,  KC_BSPC,  \
+           KC_P7,   KC_P8,    KC_P9,    KC_PEQL,  \
+  MO(_FN), KC_P4,   KC_P5,    KC_P6,    KC_PPLS,  \
+  KC_PENT, KC_P1,   KC_P2,    KC_P3,    KC_PMNS,  \
+           KC_SPC,  KC_P0,    KC_PDOT,  KC_TAB    \
+),
+[_FN] = LAYOUT(
+           RGB_TOG, RGB_MOD, RGB_HUI, RGB_HUI, \
+           _______, _______, _______, _______, \
+  _______, _______, _______, _______, _______, \
+  KC_2,    _______, _______, _______, _______, \
+           _______, _______, _______, _______  \
+),
+};
+
+const uint16_t PROGMEM fn_actions[] = {
+};
+
+const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) // MACRODOWN only works in this function
+{
+    return MACRO_NONE;
+};

keyboards/catch22/rules.mk

@@ -0,0 +1,60 @@
+# MCU name
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Bootloader
+BOOTLOADER = caterina
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+#OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   comment out to disable the options.
+#
+BOOTMAGIC_ENABLE  = no	# Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE  = no	# Mouse keys(+4700)
+EXTRAKEY_ENABLE  = no	# Audio control and System control(+450)
+CONSOLE_ENABLE  = yes	# Console for debug(+400)
+COMMAND_ENABLE  = yes    # Commands for debug and configuration
+SLEEP_LED_ENABLE  = no  # Breathing sleep LED during USB suspend
+NKRO_ENABLE  = no		# USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+BACKLIGHT_ENABLE  = no  # Custom backlighting code is used, so this should not be enabled
+AUDIO_ENABLE  = no # This can be enabled if a speaker is connected to the expansion port. Not compatible with RGBLIGHT below
+RGBLIGHT_ENABLE  = yes # This can be enabled if a ws2812 strip is connected to the expansion port.
+

keyboards/chocopad/keymaps/khord/config.h

@@ -0,0 +1,6 @@
+#ifndef CONFIG_USER_H
+#define CONFIG_USER_H
+
+#include "../../config.h"
+
+#endif

keyboards/chocopad/keymaps/khord/keymap.c

@@ -0,0 +1,104 @@
+#include "chocopad.h"
+
+#define _BASE 0
+#define _FN1 1
+#define _FN2 2
+
+// Fillers to make layering more clear
+#define KC_ KC_TRNS
+#define KC_XX KC_NO
+
+#define KC_L1 LT(1, KC_P0)
+#define KC_L2 LT(2, KC_SPC)
+#define KC_RST RESET
+#define KC_BSTP BL_STEP
+#define KC_RTOG RGB_TOG
+#define KC_RMOD RGB_MOD
+#define KC_RHUI RGB_HUI
+#define KC_RHUD RGB_HUD
+#define KC_RSAI RGB_SAI
+#define KC_RSAD RGB_SAD
+#define KC_RVAI RGB_VAI
+#define KC_RVAD RGB_VAD
+#define KC_MAC1 ADMIN
+#define KC_MAC2 SMSPC
+#define KC_M192 M192
+#define KC_M255 M255
+
+enum custom_keycodes {
+  NUMPAD = SAFE_RANGE,
+  ADMIN,
+  SMSPC,
+  M192,
+  M255
+};
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+  [_BASE] = KC_KEYMAP(
+  //,----+----+----+----.
+      P7 , P8 , P9 ,BSPC,
+  //|----+----+----+----|
+      P4 , P5 , P6 ,TAB ,
+  //|----+----+----+----|
+      P1 , P2 , P3 ,PENT,
+  //|----+----+----+----|
+      L1 , L2 ,PDOT,PSLS
+  //`----+----+----+----'
+  ),
+
+  [_FN1] = KC_KEYMAP(
+  //,----+----+----+----.
+     ESC ,MAC1,MAC2,DEL ,
+  //|----+----+----+----|
+     LEFT,DOWN, UP ,RGHT,
+  //|----+----+----+----|
+     M192,M255, XX , XX ,
+  //|----+----+----+----|
+         , XX ,    , XX
+  //`----+----+----+----'
+  ),
+
+  [_FN2] = KC_KEYMAP(
+  //,----+----+----+----.
+     RST , XX , XX , XX ,
+  //|----+----+----+----|
+     RTOG,RHUI,RSAI,RVAI,
+  //|----+----+----+----|
+     RMOD,RHUD,RSAD,RVAD,
+  //|----+----+----+----|
+     BSTP,    , XX , XX
+  //`----+----+----+----'
+  )
+
+};
+
+bool process_record_user(uint16_t keycode, keyrecord_t *record) {
+  switch (keycode) {
+    case ADMIN:
+      if (record->event.pressed) {
+	SEND_STRING("Administrator");
+      }
+      return false;
+      break;
+    case SMSPC:
+      if (record->event.pressed) {
+	SEND_STRING("Simspace1!");
+      }
+      return false;
+      break;
+    case M192:
+      if (record->event.pressed) {
+	SEND_STRING("192.168.");
+      }
+      return false;
+      break;
+    case M255:
+      if (record->event.pressed) {
+	SEND_STRING("255");
+      }
+      return false;
+      break;
+  }
+  return true;
+};

keyboards/chocopad/keymaps/khord/rules.mk

@@ -0,0 +1,5 @@
+RGBLIGHT_ENABLE = yes
+
+ifndef QUANTUM_DIR
+	include ../../../../Makefile
+endif

keyboards/ckeys/obelus/keymaps/default/keymap.c

@@ -18,7 +18,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
    * |     |     |     |     |
    * `---------------------- '
    */
-[0] = KEYMAP( /* LAYER SELECT */
+[0] = LAYOUT( /* LAYER SELECT */
   KC_TRNS, KC_TRNS, KC_TRNS, RESET, \
   TO(4),   KC_TRNS, KC_TRNS, KC_TRNS, \
   TO(1),   TO(2),   TO(3),   KC_TRNS, \
@@ -35,7 +35,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
    * |  0  |  .  |  /  |  =  |
    * `---------------------- '
    */
-[1] = KEYMAP( /* NUMPAD */
+[1] = LAYOUT( /* NUMPAD */
   KC_P7,   KC_P8,   KC_P9,   KC_PAST, \
   KC_P4,   KC_P5,   KC_P6,   KC_PMNS, \
   KC_P1,   KC_P2,   KC_P3,   KC_PPLS, \
@@ -52,7 +52,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
    * |     |     |     |     |
    * `---------------------- '
    */
-[5] = KEYMAP( /* NUMPAD SUPPLEMENT */
+[5] = LAYOUT( /* NUMPAD SUPPLEMENT */
   KC_NLCK, KC_TRNS, KC_TRNS, TO(0),   \
   KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \
   KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \
@@ -69,7 +69,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
    * |LEFT |DOWN |RIGHT|ENTER|
    * `---------------------- '
    */
-[2] = KEYMAP( /* NAV CLUSTER */
+[2] = LAYOUT( /* NAV CLUSTER */
   KC_INS,  KC_PGUP, KC_TAB,  KC_PSCR, \
   KC_DEL,  KC_PGDN, KC_VOLD, KC_VOLU, \
   KC_HOME, KC_UP,   KC_END,  TO(0),   \
@@ -86,7 +86,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
    * |CTRL |  C  |  R  |SPACE|
    * `---------------------- '
    */
-[3] = KEYMAP( /* GAMING */
+[3] = LAYOUT( /* GAMING */
   LT(4, KC_ESC),  KC_1,    KC_2,    KC_3,    \
   KC_TAB,  KC_Q,    KC_W,    KC_E,    \
   KC_LSFT, KC_A,    KC_S,    KC_D,    \
@@ -103,7 +103,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
    * |TOGGL|MODE |     |     |
    * `---------------------- '
    */
-[4] = KEYMAP( /* NUMPAD SUPPLEMENT */
+[4] = LAYOUT( /* NUMPAD SUPPLEMENT */
   KC_NO,   KC_NO,   KC_NO,   KC_NO,   \
   KC_NO,   KC_NO,   KC_NO,   KC_NO,   \
   KC_NO,   KC_NO,   KC_NO,   KC_NO,   \

keyboards/ckeys/obelus/obelus.h

@@ -7,7 +7,7 @@
 // The following is an example using the Planck MIT layout
 // The first section contains all of the arguements
 // The second converts the arguments into a two-dimensional array
-#define KEYMAP( \
+#define LAYOUT( \
     k00, k01, k02, k03, \
     k10, k11, k12, k13, \
     k20, k21, k22, k23, \

keyboards/clueboard/60/chconf.h

@@ -48,7 +48,7 @@
  * @details Frequency of the system timer that drives the system ticks. This
  *          setting also defines the system tick time unit.
  */
-#define CH_CFG_ST_FREQUENCY                 10000
+#define CH_CFG_ST_FREQUENCY                 100000
 
 /**
  * @brief   Time delta constant for the tick-less mode.

keyboards/clueboard/66/keymaps/skully/keymap.c

@@ -1,53 +0,0 @@
-#include "66.h"
-
-enum custom_keycodes {
-   M_SHRUG = SAFE_RANGE
-};
-
-// Each layer gets a name for readability, which is then used in the keymap matrix below.
-// The underscores don't mean anything - you can have a layer called STUFF or any other name.
-// Layer names don't all need to be of the same length, obviously, and you can also skip them
-// entirely and just use numbers.
-#define _BL 0
-#define _FL 1
-#define _CL 2
-
-const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
-  /* Keymap _BL: Base Layer (Default Layer)
-   */
-[_BL] = LAYOUT(
-  KC_GESC, KC_1,    KC_2,   KC_3,   KC_4,   KC_5,   KC_6,   KC_7,   KC_8,   KC_9,    KC_0,     KC_MINS,  KC_EQL,   KC_GRV,  KC_BSPC,          KC_PGUP,
-  KC_TAB,  KC_Q,    KC_W,   KC_E,   KC_R,   KC_T,   KC_Y,   KC_U,   KC_I,   KC_O,    KC_P,     KC_LBRC,  KC_RBRC,  KC_BSLS,                   KC_PGDN,
-  KC_LCTL, KC_A,    KC_S,   KC_D,   KC_F,   KC_G,   KC_H,   KC_J,   KC_K,   KC_L,    KC_SCLN,  KC_QUOT,  KC_NUHS,  KC_ENT,
-  MO(_FL), KC_NUBS, KC_Z,   KC_X,   KC_C,   KC_V,   KC_B,   KC_N,   KC_M,   KC_COMM, KC_DOT,   KC_SLSH,  KC_RO,    KC_RSFT,          KC_UP,
-  KC_LCTL, KC_LALT, KC_LGUI,KC_MHEN,          KC_SPC, KC_SPC,                        KC_HENK,  KC_RGUI,  KC_RALT,  KC_RCTL,  KC_LEFT, KC_DOWN, KC_RGHT),
-
-  /* Keymap _FL: Function Layer
-   */
-[_FL] = LAYOUT(
-  KC_GRV, KC_F1,     KC_F2,  KC_F3,  KC_F4,  KC_F5,    KC_F6,    KC_F7,  KC_F8,  KC_F9,     KC_F10,    KC_F11,    KC_F12,    S(KC_GRV), KC_DEL,           BL_STEP,
-  S(KC_TAB), S(KC_Q),   S(KC_W),S(KC_E),S(KC_R),S(KC_T),  S(KC_Y),  S(KC_U),S(KC_I),S(KC_O),   S(KC_P),   S(KC_LBRC),S(KC_RBRC),S(KC_BSLS),                  S(KC_PGDN),
-  S(KC_LCTL),S(KC_A),   MO(_CL),S(KC_D),S(KC_F),S(KC_G),  S(KC_H),  S(KC_J),S(KC_K),S(KC_L),   S(KC_SCLN),S(KC_QUOT),S(KC_NUHS),S(KC_ENT),
-  MO(_FL),   S(KC_NUBS),S(KC_Z),S(KC_X),S(KC_C),S(KC_V),  S(KC_B),  S(KC_N),S(KC_M),S(KC_COMM),S(KC_DOT), S(KC_SLSH),S(KC_RO),  KC_RSFT,           KC_PGUP,
-  KC_LCTL,   KC_LALT,   KC_LGUI,KC_MHEN,        S(KC_SPC),S(KC_SPC),                           KC_HENK,   KC_RGUI,   KC_RALT,   KC_RCTL,   KC_HOME, KC_PGDN, KC_END),
-
-  /* Keymap _CL: Control layer
-   */
-[_CL] = LAYOUT(
-  M_SHRUG, _______, _______,_______,_______,_______,_______,_______,_______,_______, _______,  _______,  _______,  _______, RGB_TOG,              RGB_VAI,
-  _______, _______, _______,_______,RESET,  _______,_______,_______,_______,_______, _______,  _______,  _______,  _______,                       RGB_VAD,
-  _______, _______, MO(_CL),_______,_______,_______,_______,_______,_______,_______, _______,  _______,  _______,  _______,
-  MO(_FL), _______, _______,_______,_______,_______,_______,_______,_______,_______, _______,  _______,  _______,  MO(_FL),               RGB_SAI,
-  _______, _______, _______,_______,        RGB_MOD,RGB_MOD,                            _______,  _______,  _______,  _______, RGB_HUD,RGB_SAD,RGB_HUI),
-};
-
-bool process_record_user(uint16_t keycode, keyrecord_t *record) {
-   if (record->event.pressed) {
-       switch(keycode) {
-           case M_SHRUG:
-               SEND_STRING("/shrug"SS_TAP(X_ENTER));
-               return false; break;
-       }
-   }
-   return true;
-};

keyboards/clueboard/66/keymaps/skully/readme.md

@@ -1,11 +0,0 @@
-![Clueboard Layout Image](http://i.imgur.com/VaoGn3M.png)
-
-# skullY's Clueboard Layout
-
-This layout is what I (@skullydazed) use on my personal Clueboards. I mostly use it for programming, CAD, and general typing.
-
-I've made the following changes from the default layout:
-
-* shift_fn on left shift
-* Change capslock to control
-* Swap Alt and Cmd

keyboards/clueboard/66/keymaps/skully/rules.mk

@@ -1,2 +0,0 @@
-RGBLIGHT_ENABLE = no
-MOUSEKEY_ENABLE = yes

keyboards/clueboard/66/rules.mk

@@ -21,3 +21,5 @@ RGBLIGHT_ENABLE = yes  # Enable keyboard underlight functionality
 MIDI_ENABLE = no 		# MIDI controls
 UNICODE_ENABLE = no 		# Unicode
 BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
+
+LAYOUTS = 66_ansi

keyboards/clueboard/66_hotswap/66_hotswap.h

@@ -1,10 +1,5 @@
-#ifndef CLUEBOARD_H
-#define CLUEBOARD_H
-
-#include "quantum.h"
+#pragma once
 
 #ifdef KEYBOARD_clueboard_66_hotswap_gen1
     #include "gen1.h"
 #endif
-
-#endif

keyboards/clueboard/66_hotswap/config.h

@@ -15,9 +15,7 @@ You should have received a copy of the GNU General Public License
 along with this program.  If not, see <http://www.gnu.org/licenses/>.
 */
 
-#ifndef CLUEBOARD_66_CONFIG_H
-#define CLUEBOARD_66_CONFIG_H
-
+#pragma once
 #include "config_common.h"
 
 /* USB Device descriptor parameter */
@@ -47,17 +45,10 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
  *  These options are also useful to firmware size reduction.
  */
 
-/* disable debug print */
 //#define NO_DEBUG
-
-/* disable print */
 //#define NO_PRINT
-
-/* disable action features */
 //#define NO_ACTION_LAYER
 //#define NO_ACTION_TAPPING
-//#define NO_ACTION_ONESHOT
-//#define NO_ACTION_MACRO
+#define NO_ACTION_ONESHOT
+#define NO_ACTION_MACRO
 //#define NO_ACTION_FUNCTION
-
-#endif

keyboards/clueboard/66_hotswap/gen1/config.h

@@ -1,6 +1,4 @@
-#ifndef CLUEBOARD_66_REV3_CONFIG_H
-#define CLUEBOARD_66_REV3_CONFIG_H
-
+#pragma once
 #include "config_common.h"
 
 #define PRODUCT_ID      0x2390
@@ -26,7 +24,9 @@
 
 /* Speaker configuration
  */
-//#define SPEAKER_PIN B7 // FIXME: find the correct name for this define
+#define B7_AUDIO
+#define NO_MUSIC_MODE
+#define AUDIO_CLICKY
 
 /* Backlight configuration
  */
@@ -49,5 +49,3 @@
 #define RGBLIGHT_EFFECT_KNIGHT_OFFSET 16   // The led to start at
 #define RGBLIGHT_EFFECT_KNIGHT_LED_NUM 8  // How many LEDs to travel
 #define RGBLIGHT_EFFECT_SNAKE_LENGTH 4    // How many LEDs wide to light up
-
-#endif

keyboards/clueboard/66_hotswap/gen1/gen1.h

@@ -1,7 +1,5 @@
-#ifndef gen1_H
-#define gen1_H
-
-#include "66_hotswap.h"
+#pragma once
+#include "quantum.h"
 
 /* Clueboard matrix layout
  * ,-----------------------------------------------------------.  ,---.
@@ -67,5 +65,3 @@
     { k80, k81, k82, k83, KC_NO, k85, k86, KC_NO }, \
     { KC_NO, KC_NO, k92, k93, k94, k95, k96, k97 }  \
 }
-
-#endif

keyboards/clueboard/66_hotswap/gen1/rules.mk

@@ -1 +1,24 @@
-BACKLIGHT_ENABLE = yes
+EXTRAFLAGS += -flto
+LAYOUTS = 66_ansi
+MCU = atmega32u4
+F_CPU = 16000000
+ARCH = AVR8
+F_USB = $(F_CPU)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+# Build Options
+#   comment out to disable the options.
+#
+BACKLIGHT_ENABLE = yes
+BOOTMAGIC_ENABLE = no
+MOUSEKEY_ENABLE = no
+EXTRAKEY_ENABLE = yes
+CONSOLE_ENABLE = yes
+COMMAND_ENABLE = no
+NKRO_ENABLE = yes
+AUDIO_ENABLE = yes
+RGBLIGHT_ENABLE = yes
+MIDI_ENABLE = no
+UNICODE_ENABLE = no
+BLUETOOTH_ENABLE = no

keyboards/clueboard/66_hotswap/info.json

@@ -3,8 +3,12 @@
   "width": 16.5,
   "height": 5,
   "layouts": {
-    "KEYMAP": {
+    "LAYOUT": {
       "layout": [{"x": 0, "y": 0, "w": 1, "label": "GRAVE"}, {"x": 1, "y": 0, "w": 1, "label": "1"}, {"x": 2, "y": 0, "w": 1, "label": "2"}, {"x": 3, "y": 0, "w": 1, "label": "3"}, {"x": 4, "y": 0, "w": 1, "label": "4"}, {"x": 5, "y": 0, "w": 1, "label": "5"}, {"x": 6, "y": 0, "w": 1, "label": "6"}, {"x": 7, "y": 0, "w": 1, "label": "7"}, {"x": 8, "y": 0, "w": 1, "label": "8"}, {"x": 9, "y": 0, "w": 1, "label": "9"}, {"x": 10, "y": 0, "w": 1, "label": "0"}, {"x": 11, "y": 0, "w": 1, "label": "DASH"}, {"x": 12, "y": 0, "w": 1, "label": "EQUALSIGN"}, {"x": 13, "y": 0, "w": 1, "label": "YEN"}, {"x": 14, "y": 0, "w": 1, "label": "BACKSPACE"}, {"x": 15.5, "y": 0, "w": 1, "label": "PAGEUP"}, {"x": 0, "y": 1, "w": 1.5, "label": "TAB"}, {"x": 1.5, "y": 1, "w": 1, "label": "Q"}, {"x": 2.5, "y": 1, "w": 1, "label": "W"}, {"x": 3.5, "y": 1, "w": 1, "label": "E"}, {"x": 4.5, "y": 1, "w": 1, "label": "R"}, {"x": 5.5, "y": 1, "w": 1, "label": "T"}, {"x": 6.5, "y": 1, "w": 1, "label": "Y"}, {"x": 7.5, "y": 1, "w": 1, "label": "U"}, {"x": 8.5, "y": 1, "w": 1, "label": "I"}, {"x": 9.5, "y": 1, "w": 1, "label": "O"}, {"x": 10.5, "y": 1, "w": 1, "label": "P"}, {"x": 11.5, "y": 1, "w": 1, "label": "LBRACKET"}, {"x": 12.5, "y": 1, "w": 1, "label": "RBRACKET"}, {"x": 13.5, "y": 1, "w": 1.5, "label": "BACKSLASH"}, {"x": 15.5, "y": 1, "w": 1, "label": "PAGEDOWN"}, {"x": 0, "y": 2, "w": 1.75, "label": "CAPSLOCK"}, {"x": 1.75, "y": 2, "w": 1, "label": "A"}, {"x": 2.75, "y": 2, "w": 1, "label": "S"}, {"x": 3.75, "y": 2, "w": 1, "label": "D"}, {"x": 4.75, "y": 2, "w": 1, "label": "F"}, {"x": 5.75, "y": 2, "w": 1, "label": "G"}, {"x": 6.75, "y": 2, "w": 1, "label": "H"}, {"x": 7.75, "y": 2, "w": 1, "label": "J"}, {"x": 8.75, "y": 2, "w": 1, "label": "K"}, {"x": 9.75, "y": 2, "w": 1, "label": "L"}, {"x": 10.75, "y": 2, "w": 1, "label": "SEMICOLON"}, {"x": 11.75, "y": 2, "w": 1, "label": "QUOTE"}, {"x": 12.75, "y": 2, "w": 1, "label": "ISOHASH"}, {"x": 13.75, "y": 2, "w": 1.25, "label": "ENTER"}, {"x": 0, "y": 3, "w": 1.25, "label": "LSHIFT"}, {"x": 1.25, "y": 3, "w": 1, "label": "ISOBACKSLASH"}, {"x": 2.25, "y": 3, "w": 1, "label": "Z"}, {"x": 3.25, "y": 3, "w": 1, "label": "X"}, {"x": 4.25, "y": 3, "w": 1, "label": "C"}, {"x": 5.25, "y": 3, "w": 1, "label": "V"}, {"x": 6.25, "y": 3, "w": 1, "label": "B"}, {"x": 7.25, "y": 3, "w": 1, "label": "N"}, {"x": 8.25, "y": 3, "w": 1, "label": "M"}, {"x": 9.25, "y": 3, "w": 1, "label": "COMMA"}, {"x": 10.25, "y": 3, "w": 1, "label": "PERIOD"}, {"x": 11.25, "y": 3, "w": 1, "label": "SLASH"}, {"x": 12.25, "y": 3, "w": 1, "label": "JPBACKSLASH"}, {"x": 13.25, "y": 3, "w": 1.25, "label": "RSHIFT"}, {"x": 14.5, "y": 3, "w": 1, "label": "UP"}, {"x": 0, "y": 4, "w": 1.25, "label": "LCTRL"}, {"x": 1.25, "y": 4, "w": 1, "label": "LALT"}, {"x": 2.25, "y": 4, "w": 1.25, "label": "LCMD"}, {"x": 3.5, "y": 4, "w": 1.25, "label": "MUHENKAN"}, {"x": 4.75, "y": 4, "w": 2, "label": "SPACE1"}, {"x": 6.75, "y": 4, "w": 2, "label": "SPACE2"}, {"x": 8.75, "y": 4, "w": 1.25, "label": "HENKAN"}, {"x": 10, "y": 4, "w": 1.25, "label": "RCMD"}, {"x": 11.25, "y": 4, "w": 1, "label": "RCTRL"}, {"x": 12.25, "y": 4, "w": 1.25, "label": "FN"}, {"x": 13.5, "y": 4, "w": 1, "label": "LEFT"}, {"x": 14.5, "y": 4, "w": 1, "label": "DOWN"}, {"x": 15.5, "y": 4, "w": 1, "label": "RIGHT"}]
+    },
+
+    "LAYOUT_66_ansi": {
+      "layout": [{"label":"~", "x":0, "y":0}, {"label":"!", "x":1, "y":0}, {"label":"@", "x":2, "y":0}, {"label":"#", "x":3, "y":0}, {"label":"$", "x":4, "y":0}, {"label":"%", "x":5, "y":0}, {"label":"^", "x":6, "y":0}, {"label":"&", "x":7, "y":0}, {"label":"*", "x":8, "y":0}, {"label":"(", "x":9, "y":0}, {"label":")", "x":10, "y":0}, {"label":"_", "x":11, "y":0}, {"label":"+", "x":12, "y":0}, {"label":"Backspace", "x":13, "y":0, "w":2}, {"x":15.5, "y":0}, {"label":"Tab", "x":0, "y":1, "w":1.5}, {"label":"Q", "x":1.5, "y":1}, {"label":"W", "x":2.5, "y":1}, {"label":"E", "x":3.5, "y":1}, {"label":"R", "x":4.5, "y":1}, {"label":"T", "x":5.5, "y":1}, {"label":"Y", "x":6.5, "y":1}, {"label":"U", "x":7.5, "y":1}, {"label":"I", "x":8.5, "y":1}, {"label":"O", "x":9.5, "y":1}, {"label":"P", "x":10.5, "y":1}, {"label":"{", "x":11.5, "y":1}, {"label":"}", "x":12.5, "y":1}, {"label":"|", "x":13.5, "y":1, "w":1.5}, {"x":15.5, "y":1}, {"label":"Caps Lock", "x":0, "y":2, "w":1.75}, {"label":"A", "x":1.75, "y":2}, {"label":"S", "x":2.75, "y":2}, {"label":"D", "x":3.75, "y":2}, {"label":"F", "x":4.75, "y":2}, {"label":"G", "x":5.75, "y":2}, {"label":"H", "x":6.75, "y":2}, {"label":"J", "x":7.75, "y":2}, {"label":"K", "x":8.75, "y":2}, {"label":"L", "x":9.75, "y":2}, {"label":":", "x":10.75, "y":2}, {"label":"\"", "x":11.75, "y":2}, {"label":"Enter", "x":12.75, "y":2, "w":2.25}, {"label":"Shift", "x":0, "y":3, "w":2.25}, {"label":"Z", "x":2.25, "y":3}, {"label":"X", "x":3.25, "y":3}, {"label":"C", "x":4.25, "y":3}, {"label":"V", "x":5.25, "y":3}, {"label":"B", "x":6.25, "y":3}, {"label":"N", "x":7.25, "y":3}, {"label":"M", "x":8.25, "y":3}, {"label":"<", "x":9.25, "y":3}, {"label":">", "x":10.25, "y":3}, {"label":"?", "x":11.25, "y":3}, {"label":"Shift", "x":12.25, "y":3, "w":2.25}, {"x":14.5, "y":3}, {"label":"Ctrl", "x":0, "y":4, "w":1.25}, {"label":"Win", "x":1.25, "y":4, "w":1.25}, {"label":"Alt", "x":2.5, "y":4, "w":1.25}, {"x":3.75, "y":4, "w":6.25}, {"label":"Alt", "x":10, "y":4, "w":1.25}, {"label":"Win", "x":11.25, "y":4}, {"label":"Menu", "x":12.25, "y":4, "w":1.25}, {"x":13.5, "y":4}, {"x":14.5, "y":4}, {"x":15.5, "y":4}]
     }
   }
 }

keyboards/clueboard/66_hotswap/rules.mk

@@ -1,23 +0,0 @@
-DEFAULT_FOLDER = clueboard/66_hotswap/gen1
-LAYOUTS = 66_ansi
-MCU = atmega32u4
-F_CPU = 16000000
-ARCH = AVR8
-F_USB = $(F_CPU)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-# Build Options
-#   comment out to disable the options.
-#
-BOOTMAGIC_ENABLE = no 	# Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = no	# Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes 	# Audio control and System control(+450)
-CONSOLE_ENABLE = yes	# Console for debug(+400)
-COMMAND_ENABLE = yes	# Commands for debug and configuration
-NKRO_ENABLE = yes	# USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-AUDIO_ENABLE = no
-RGBLIGHT_ENABLE = yes	# Enable keyboard underlight functionality
-MIDI_ENABLE = no 	# MIDI controls
-UNICODE_ENABLE = no 	# Unicode
-BLUETOOTH_ENABLE = no	# Enable Bluetooth with the Adafruit EZ-Key HID

keyboards/clueboard/keymaps/xyverz/config.h

@@ -1,3 +0,0 @@
-#include "../config.h"
-
-#define TAPPING_TERM 600 // ms	

keyboards/contra/keymaps/maxr1998/keymap.c

@@ -20,19 +20,13 @@
 enum contra_layers {
   _QWERTZ,
   _FUNC,
-  _NUMPAD,
   _NUMROW
 };
 
+#define KC_I3 LM(_NUMROW, MOD_LALT)
+#define KC_NR MO(_NUMROW)
+#define NR_L3 SAFE_RANGE
 #define FUN MO(_FUNC)
-#define NPK TT(_NUMPAD)
-//#define SPEC_S LM(_NUMROW, (KC_LSFT))
-//#define SPEC_L3 LM(_NUMROW, (DE_ALGR))
-
-enum custom_keycodes {
-    SPEC_S = SAFE_RANGE,
-    SPEC_L3
-};
 
 const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
 
@@ -44,21 +38,21 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
  * |------+------+------+------+------+------|------+------+------+------+------+------|
  * | Shift|   Y  |   X  |   C  |   V  |   B  |   N  |   M  |   ,  |   .  |  Up  | Shift|
  * |------+------+------+------+------+------+------+------+------+------+------+------|
- * | Ctrl | Sup  | Alt  | NumP | Spec |    Space    | Sp_A | Fun  | Left | Down | Right|
+ * | Ctrl | Sup  | Alt  |  i3  | NumR |    Space    | Spec | Fun  | Left | Down | Right|
  * `-----------------------------------------------------------------------------------'
  */
 [_QWERTZ] = {
   {KC_GESC, KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_BSPC},
   {KC_TAB,  KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,    KC_L,    DE_PLUS, KC_ENT },
   {KC_LSFT, KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_UP,   KC_RSFT},
-  {KC_LCTL, KC_LGUI, KC_LALT, NPK,     SPEC_S,  KC_SPC,  KC_SPC,  SPEC_L3, FUN,     KC_LEFT, KC_DOWN, KC_RGHT}
+  {KC_LCTL, KC_LGUI, KC_LALT, KC_I3,   KC_NR,   KC_SPC,  KC_SPC,  NR_L3,   FUN,     KC_LEFT, KC_DOWN, KC_RGHT}
 },
 
 /* Function layer
  * ,-----------------------------------------------------------------------------------.
  * |      |      |      |      |      |      |      |   Ü  |      |   Ö  |      | Del  |
  * |------+------+------+------+------+-------------+------+------+------+------+------|
- * | Lock |   Ä  |      |      |      |      |      | RGBS | RGBB | RGBS |      |      |
+ * | Lock |   Ä  |   ß  |      |      |      |      | RGBS | RGBB | RGBS |      |      |
  * |------+------+------+------+------+------|------+------+------+------+------+------|
  * |      |      |      |      |      |      |      | RGBH-| RGBT | RGBH+| PgUp |      |
  * |------+------+------+------+------+------+------+------+------+------+------+------|
@@ -67,7 +61,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
  */
 [_FUNC] = {
   {_______, _______, _______, _______, _______, _______, _______, DE_UE,   _______, DE_OE,   _______, KC_DEL },
-  {KC_LOCK, DE_AE,   _______, _______, _______, _______, _______, RGB_M_P, RGB_M_B, RGB_M_SW,_______, _______},
+  {KC_LOCK, DE_AE,   DE_SS,   _______, _______, _______, _______, RGB_M_P, RGB_M_B, RGB_M_SW,_______, _______},
   {_______, _______, _______, _______, _______, _______, _______, RGB_HUD, RGB_TOG, RGB_HUI, KC_PGUP, _______},
   {_______, _______, _______, XXXXXXX, XXXXXXX, _______, _______, XXXXXXX, XXXXXXX, KC_HOME, KC_PGDN, KC_END }
 },
@@ -76,51 +70,23 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
  * ,-----------------------------------------------------------------------------------.
  * |      |  1   |  2   |  3   |  4   |  5   |  6   |  7   |  8   |  9   |  0   |  ß   |
  * |------+------+------+------+------+-------------+------+------+------+------+------|
- * |      |      |      |      |      |      |      |      |      |      |      |      |
+ * |      |      |      |      |      |      |      |      |      |      |  #'  |      |
  * |------+------+------+------+------+------|------+------+------+------+------+------|
- * |      |  ><| |      |      |      |      |      |      |      |      | _  - |      |
+ * |      | <> | |      |      |      |      |      |      |      |      |  -_  |      |
  * |------+------+------+------+------+------+------+------+------+------+------+------|
  * |      |      |      | ---- | ---- |      |      | ---- | ---- |      |      |      |
  * `-----------------------------------------------------------------------------------'
  */
 [_NUMROW] = {
   {_______, DE_1,    DE_2,    DE_3,    DE_4,    DE_5,    DE_6,    DE_7,    DE_8,    DE_9,    DE_0,    DE_SS  },
-  {_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______},
+  {_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, DE_HASH, _______},
   {_______, DE_LESS, _______, _______, _______, _______, _______, _______, _______, _______, DE_MINS, _______},
   {_______, _______, _______, XXXXXXX, XXXXXXX, _______, _______, XXXXXXX, XXXXXXX, _______, _______, _______}
-},
-
-/* Numpad layer
- * ,-----------------------------------------------------------------------------------.
- * |      |  +   |  7   |  8   |  9   |      |      |      |      |      |      |      |
- * |------+------+------+------+------+-------------+------+------+------+------+------|
- * |      |  -   |  4   |  5   |  6   |      |      |      |      |      |      |      |
- * |------+------+------+------+------+------|------+------+------+------+------+------|
- * |      |  *   |  1   |  2   |  3   |      |      |      |      |      |      |      |
- * |------+------+------+------+------+------+------+------+------+------+------+------|
- * |      |  /   |  0   | ---- | ---- |      |      | ---- | ---- |      |      |      |
- * `-----------------------------------------------------------------------------------'
- */
-[_NUMPAD] = {
-  {DEBUG,   KC_PPLS, KC_P7,   KC_P8,   KC_P9,   _______, _______, _______, _______, _______, _______, _______},
-  {_______, KC_PMNS, KC_P4,   KC_P5,   KC_P6,   _______, _______, _______, _______, _______, _______, _______},
-  {_______, KC_PAST, KC_P1,   KC_P2,   KC_P3,   _______, _______, _______, _______, _______, _______, _______},
-  {_______, KC_PSLS, KC_P0,   _______, XXXXXXX, _______, _______, XXXXXXX, XXXXXXX, _______, _______, _______}
 }
 };
 
 bool process_record_user(uint16_t keycode, keyrecord_t *record) {
-  switch (keycode) {
-    case SPEC_S:
-    if (record->event.pressed) {
-      register_code(KC_LSFT);
-      layer_on(_NUMROW);
-    } else {
-      layer_off(_NUMROW);
-      unregister_code(KC_LSFT);
-    }
-    return false;
-    case SPEC_L3:
+  if (keycode == NR_L3) {
     if (record->event.pressed) {
       register_code(DE_ALGR);
       layer_on(_NUMROW);
@@ -129,9 +95,8 @@ bool process_record_user(uint16_t keycode, keyrecord_t *record) {
       unregister_code(DE_ALGR);
     }
     return false;
-    default:
-    return true;
   }
+  return true;
 }
 
 void led_set_user(uint8_t usb_led) {

keyboards/contra/keymaps/maxr1998/readme.md

@@ -1 +1,2 @@
-# Contra Layout by Maxr1998
+# Contra Layout by Maxr1998
+![img](https://i.imgur.com/dVnnRDT.jpg)

keyboards/contra/keymaps/maxr1998/rules.mk

@@ -1,8 +1,13 @@
 RGBLIGHT_ENABLE = yes
 KEY_LOCK_ENABLE = yes
 
+EXTRAFLAGS      += -flto
+UNICODE_ENABLE  = no
+MOUSEKEY_ENABLE = no
+
 ### Debugging ###
-#CONSOLE_ENABLE = yes
+CONSOLE_ENABLE  = no # yes
+COMMAND_ENABLE  = no
 
 ifndef QUANTUM_DIR
 	include ../../../../Makefile

keyboards/converter/m0110_usb/README.md

@@ -0,0 +1,51 @@
+M0110(A) keyboard converter
+======================================
+This is a port of the original M0110 converter from TMK to QMK. The original converter was designed to work with **ATmega32U2** and **ATmega32U4** based microcontrollers to convert Apple M0110/M0110A keyboards and M0120 numpads to USB. This port has been tested to be compatible with the [**Adafruit Feather 32U4 BLE**](https://learn.adafruit.com/adafruit-feather-32u4-bluefruit-le).
+
+
+### Enabling Bluetooth for the Adafruit Feather 32U4 BLE
+----------------------------------------------------
+Simply add `BLUETOOTH = AdafruitBLE` to your `rules.mk` file. This enables code specifically for the Adafruit Feather 32U4 BLE. If enabled, the device will use the `PRODUCT` and `DESCRIPTION` values from `config.h` for the device name displayed by the Feather on host devices. You can simply change these values to change the device name.
+
+
+### Pins
+----
+This port utilizes the same pins that the TMK converter used. `PD1` is used for `CLOCK` and `PD0` is used for the `DATA` from the keyboard. These pins can be changed in `config.h`.
+
+
+### Other important hardware notes from the original TMK converter Readme:
+>### Hardware
+>--------
+>You can buy preassembled [TMK converter] or make yourown with AVR dev board like PJRC [Teensy].
+>
+>Port of the MCU `PD1` is assigned to `CLOCK` line and `PD0` to `DATA` by default, you can change pin configuration with editing `config.h`.
+>
+>[![M0110 Converter](http://i.imgur.com/yEp2eRim.jpg)](http://i.imgur.com/yEp2eRi.jpg)
+>
+>#### 4P4C phone handset cable
+>Note that original cable used with Mac is **straight** while phone handset cable is **crossover**.
+>
+><http://en.wikipedia.org/wiki/Modular_connector#4P4C>
+>
+>[Teensy]: http://www.pjrc.com/teensy/
+>[TMK converter]: https://geekhack.org/index.php?topic=72052.0
+>
+>
+>#### Socket Pinout
+>- <http://pinouts.ru/Inputs/MacKeyboard_pinout.shtml>
+>
+>![Jack fig](http://www.kbdbabel.org/conn/kbd_connector_macplus.png)
+>
+>
+>#### Pull-up Resistor
+>You may need pull-up resistors on signal lines(`CLOCK`, `DATA`) in particular when you have long or coiled cable. **1k-10k Ohm** will be OK >for this purpose. In that case the converter may not read signal from keyboard correctly without pull-up resistors.
+>
+
+[**View the original TMK converter Readme**](https://github.com/tmk/tmk_keyboard/tree/master/converter/m0110_usb)\
+[**View the original TMK converter Repository**](https://github.com/tmk/tmk_keyboard/tree/master/converter/m0110_usb)
+
+
+### QMK Port Changelog
+---------
+- 2018/08/01 - Original Release
+

keyboards/converter/m0110_usb/config.h

@@ -0,0 +1,59 @@
+/*
+Copyright 2011,2012 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+
+--------------
+
+Ported to QMK by Techsock <info@techsock.com>
+*/
+
+#pragma once
+
+#define VENDOR_ID       0xFEED
+#define PRODUCT_ID      0x0110
+#define DEVICE_VER      0x0101
+#define MANUFACTURER    Apple
+#define PRODUCT         M0110(A)
+#define DESCRIPTION     Converts M0110(A) to USB and/or BT
+
+/* matrix size */
+#define MATRIX_ROWS 14
+#define MATRIX_COLS 8
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/* magic key */
+#define IS_COMMAND() ( \
+    keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_LALT) | MOD_BIT(KC_LGUI)) || \
+    keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_LALT) | MOD_BIT(KC_LCTL)) \
+)
+
+/* boot magic key */
+#define BOOTMAGIC_KEY_SALT                      KC_M
+
+/* ports */
+#define M0110_CLOCK_PORT        PORTD
+#define M0110_CLOCK_PIN         PIND
+#define M0110_CLOCK_DDR         DDRD
+#define M0110_CLOCK_BIT         1
+#define M0110_DATA_PORT         PORTD
+#define M0110_DATA_PIN          PIND
+#define M0110_DATA_DDR          DDRD
+#define M0110_DATA_BIT          0
+
+

keyboards/converter/m0110_usb/keymaps/default/keymap.c

@@ -0,0 +1,92 @@
+/*
+Copyright 2011,2012,2015 Jun Wako <wakojun@gmail.com>
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+
+--------------
+
+Ported to QMK by Techsock <info@techsock.com>
+*/
+
+#include QMK_KEYBOARD_H
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+	/* Default:
+	 * M0110                                                       M0120
+	 * ,---------------------------------------------------------. ,---------------.
+	 * |  `|  1|  2|  3|  4|  5|  6|  7|  8|  9|  0|  -|  =|Backs| |Nlk|  =|  /|  *|
+	 * |---------------------------------------------------------| |---------------|
+	 * |Tab  |  Q|  W|  E|  R|  T|  Y|  U|  I|  O|  P|  [|  ]|  \| |  7|  8|  9|  -|
+	 * |---------------------------------------------------------| |---------------|
+	 * |Caps  |  A|  S|  D|  F|  G|  H|  J|  K|  L|  ;|  '|Return| |  4|  5|  6|  +|
+	 * |---------------------------------------------------------| |---------------|
+	 * |Shift   |  Z|  X|  C|  V|  B|  N|  M|  ,|  .|  /|Shift   | |  1|  2|  3|   |
+	 * `---------------------------------------------------------' |-----------|Ent|
+	 *      |Opt|Mac |         Space               |Fn  |Opt|      |      0|  .|   |
+	 *      `-----------------------------------------------'      `---------------'
+	 * M0110A
+	 * ,---------------------------------------------------------. ,---------------.
+	 * |  `|  1|  2|  3|  4|  5|  6|  7|  8|  9|  0|  -|  =|Backs| |Nlk|  =|  /|  *|
+	 * |---------------------------------------------------------| |---------------|
+	 * |Tab  |  Q|  W|  E|  R|  T|  Y|  U|  I|  O|  P|  [|  ]|   | |  7|  8|  9|  -|
+	 * |-----------------------------------------------------'   | |---------------|
+	 * |Caps  |  A|  S|  D|  F|  G|  H|  J|  K|  L|  ;|  '|Return| |  4|  5|  6|  +|
+	 * |---------------------------------------------------------| |---------------|
+	 * |Shift   |  Z|  X|  C|  V|  B|  N|  M|  ,|  .|  /|Shft|Up | |  1|  2|  3|   |
+	 * |---------------------------------------------------------| |-----------|Ent|
+	 * |Opt  |Mac    |         Space             |  \|Lft|Rgt|Dn | |      0|  .|   |
+	 * `---------------------------------------------------------' `---------------'
+	 */
+
+	[0] = LAYOUT_ansi(
+	       KC_GRV,  KC_1,    KC_2, KC_3, KC_4, KC_5,   KC_6, KC_7, KC_8,    KC_9,   KC_0,             KC_MINS, KC_EQL,  KC_BSPC,  KC_NLCK, KC_EQL, KC_PSLS, KC_PAST, \
+	       KC_TAB,  KC_Q,    KC_W, KC_E, KC_R, KC_T,   KC_Y, KC_U, KC_I,    KC_O,   KC_P,             KC_LBRC, KC_RBRC,           KC_P7,   KC_P8,  KC_P9,   KC_PMNS, \
+	       KC_LCAP, KC_A,    KC_S, KC_D, KC_F, KC_G,   KC_H, KC_J, KC_K,    KC_L,   KC_SCLN,          KC_QUOT,          KC_ENT,   KC_P4,   KC_P5,  KC_P6,   KC_PPLS, \
+	       KC_LSFT, KC_Z,    KC_X, KC_C, KC_V, KC_B,   KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH,                            KC_UP,    KC_P1,   KC_P2,  KC_P3,   KC_PENT, \
+	       KC_LALT, KC_LGUI,                   KC_SPC,                      MO(1),  LT(1, KC_BSLASH), KC_LEFT, KC_RGHT, KC_DOWN,  KC_P0,           KC_PDOT),
+		
+	
+	/* Cursor Layer:
+	 * M0110                                                       M0120
+	 * ,---------------------------------------------------------. ,---------------.
+	 * |Esc| F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12|Delet| |Nlk|  =|  /|  *|
+	 * |---------------------------------------------------------| |---------------|
+	 * |Tab  |Hom| Up|PgU|Rst|   |   |   |Psc|Slk|Pau|Up |INS|   | |  7|  8|  9|  -|
+	 * |---------------------------------------------------------| |---------------|
+	 * |Ctrl  |Lef|Dow|Rig|   |   |   |   |Hom|PgU|Lef|Rig|Return| |  4|  5|  6|  +|
+	 * |---------------------------------------------------------| |---------------|
+	 * |Shift   |End|   |PgD|   |   |   |   |End|PgD|Dow|Shift   | |  1|  2|  3|   |
+	 * `---------------------------------------------------------' |-----------|Ent|
+	 *      |Opt|Mac |         Space               |Fn  |Opt|      |      0|  .|   |
+	 *      `-----------------------------------------------'      `---------------'
+	 * M0110A
+	 * ,---------------------------------------------------------. ,---------------.
+	 * |Esc| F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12|Delet| |Nlk|  =|  /|  *|
+	 * |---------------------------------------------------------| |---------------|
+	 * |Tab  |Hom| Up|PgU|   |   |   |   |Psc|Slk|Pau|Up |INS|   | |  7|  8|  9|  -|
+	 * |-----------------------------------------------------'   | |---------------|
+	 * |Caps  |Lef|Dow|Rig|   |   |   |   |Hom|PgU|Lef|Rig|Return| |  4|  5|  6|  +|
+	 * |---------------------------------------------------------| |---------------|
+	 * |Ctrl    |End|   |PgD|   |   |   |   |End|PgD|Dow|Shft|PgU| |  1|  2|  3|   |
+	 * |---------------------------------------------------------| |-----------|Ent|
+	 * |Opt  |Mac    |         Space             |  \|Hom|End|PgD| |      0|  .|   |
+	 * `---------------------------------------------------------' `---------------'
+	 */
+	
+	[1] = LAYOUT_ansi(
+	       KC_ESC,  KC_F1,   KC_F2,   KC_F3,   KC_F4, KC_F5, KC_F6, KC_F7, KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12, KC_DEL,   KC_NLCK, KC_EQL, KC_PSLS, KC_PAST, \
+		   KC_TAB,  KC_HOME, KC_UP,   KC_PGUP, RESET, KC_NO, KC_NO, KC_NO, KC_PSCR, KC_SLCK, KC_PAUS, KC_UP,   KC_INS,           KC_P7,   KC_P8,  KC_P9,   KC_PMNS, \
+		   KC_LCAP, KC_LEFT, KC_DOWN, KC_RGHT, KC_NO, KC_NO, KC_NO, KC_NO, KC_HOME, KC_PGUP, KC_LEFT, KC_RGHT,         KC_ENT,   KC_P4,   KC_P5,  KC_P6,   KC_PPLS, \
+		   KC_LCTL, KC_END,  KC_NO,   KC_PGDN, KC_NO, KC_NO, KC_NO, KC_NO, KC_END,  KC_PGDN, KC_DOWN,                  KC_PGUP,  KC_P1,   KC_P2,  KC_P3,   KC_PENT, \
+	       KC_LALT, KC_LGUI,                          KC_SPC,                       KC_TRNS, KC_TRNS, KC_HOME, KC_END, KC_PGDN,  KC_P0,           KC_PDOT),
+
+};

keyboards/converter/m0110_usb/m0110_usb.c

@@ -0,0 +1,3 @@
+#include "m0110_usb.h"
+#include <avr/io.h>
+#include "quantum.h"

keyboards/converter/m0110_usb/m0110_usb.h

@@ -0,0 +1,131 @@
+/*
+Copyright 2011,2012,2014,2015 Jun Wako <wakojun@gmail.com>
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+
+--------------
+
+Ported to QMK by Techsock <info@techsock.com>
+*/
+
+#ifndef M0110_USB_H
+#define M0110_USB_H
+#endif
+
+#include "quantum.h"
+
+/* Common layout for M0110 and M0110A
+ * This keymap works with both keyboards. As you can see, the M0110A is 
+ * a superset of M0110 keyboard, only one exception is 'Enter'(34) of M0110
+ * does not exist on the M0110A.
+ *
+ * ,---------------------------------------------------------. ,---------------.
+ * |  `|  1|  2|  3|  4|  5|  6|  7|  8|  9|  0|  -|  =|Backs| |Clr|  =|  /|  *|
+ * |---------------------------------------------------------| |---------------|
+ * |Tab  |  Q|  W|  E|  R|  T|  Y|  U|  I|  O|  P|  [|  ]|   | |  7|  8|  9|  -|
+ * |-----------------------------------------------------'   | |---------------|
+ * |Caps  |  A|  S|  D|  F|  G|  H|  J|  K|  L|  ;|  '|Return| |  4|  5|  6|  +|
+ * |---------------------------------------------------------| |---------------|
+ * |Shift   |  Z|  X|  C|  V|  B|  N|  M|  ,|  ,|  /|Shft|Up | |  1|  2|  3|   |
+ * |---------------------------------------------------------| |-----------|Ent|
+ * |Opt  |Mac    |         Space         |Ent|  \|Lft|Rgt|Dn | |      0|  .|   |
+ * `---------------------------------------------------------' `---------------'
+ *
+ * M0110A scan codes
+ * ,---------------------------------------------------------. ,---------------.
+ * | 32| 12| 13| 14| 15| 17| 16| 1A| 1C| 19| 1D| 1B| 18|   33| | 47| 68| 6D| 62|
+ * |---------------------------------------------------------| |---------------|
+ * |   30| 0C| 0D| 0E| 0F| 11| 10| 20| 22| 1F| 23| 21| 1E|   | | 59| 5B| 5C| 4E|
+ * |-----------------------------------------------------'   | |---------------|
+ * |    39| 00| 01| 02| 03| 05| 04| 26| 28| 25| 29| 27|    24| | 56| 57| 58| 66|
+ * |---------------------------------------------------------| |---------------|
+ * |      38| 06| 07| 08| 09| 0B| 2D| 2E| 2B| 2F| 2C|  38| 4D| | 53| 54| 55|   |
+ * `---------------------------------------------------------' |-----------| 4C|
+ * |   3A|     37|             31            | 2A| 46| 42| 48| |     52| 41|   |
+ * `---------------------------------------------------------' `---------------'
+ *
+ * M0110 + M0120 scan codes
+ * ,---------------------------------------------------------. ,---------------.
+ * | 32| 12| 13| 14| 15| 17| 16| 1A| 1C| 19| 1D| 1B| 18|   33| | 47| 68| 6D| 62|
+ * |---------------------------------------------------------| |---------------|
+ * |   30| 0C| 0D| 0E| 0F| 11| 10| 20| 22| 1F| 23| 21| 1E| 2A| | 59| 5B| 5C| 4E|
+ * |---------------------------------------------------------| |---------------|
+ * |    39| 00| 01| 02| 03| 05| 04| 26| 28| 25| 29| 27|    24| | 56| 57| 58| 66|
+ * |---------------------------------------------------------| |---------------|
+ * |      38| 06| 07| 08| 09| 0B| 2D| 2E| 2B| 2F| 2C|      38| | 53| 54| 55|   |
+ * `---------------------------------------------------------' |-----------| 4C|
+ *      | 3A|  37|             31              |   34| 3A|     |     52| 41|   |
+ *      `------------------------------------------------'     `---------------'
+ * Two right and left keys of 38 and 3A are identical, you cannot discriminate those two.
+ */
+#define LAYOUT_ansi( \
+    K32,K12,K13,K14,K15,K17,K16,K1A,K1C,K19,K1D,K1B,K18,K33,  K47,K68,K6D,K62, \
+    K30,K0C,K0D,K0E,K0F,K11,K10,K20,K22,K1F,K23,K21,K1E,      K59,K5B,K5C,K4E, \
+    K39,K00,K01,K02,K03,K05,K04,K26,K28,K25,K29,K27,    K24,  K56,K57,K58,K66, \
+    K38,K06,K07,K08,K09,K0B,K2D,K2E,K2B,K2F,K2C,        K4D,  K53,K54,K55,K4C, \
+    K3A,K37,            K31,            K34,K2A,K46,K42,K48,  K52,    K41      \
+) { \
+    { K00,    K01,    K02,    K03,    K04,    K05,    K06,    K07   }, \
+    { K08,    K09,    KC_NO,  K0B,    K0C,    K0D,    K0E,    K0F   }, \
+    { K10,    K11,    K12,    K13,    K14,    K15,    K16,    K17   }, \
+    { K18,    K19,    K1A,    K1B,    K1C,    K1D,    K1E,    K1F   }, \
+    { K20,    K21,    K22,    K23,    K24,    K25,    K26,    K27   }, \
+    { K28,    K29,    K2A,    K2B,    K2C,    K2D,    K2E,    K2F   }, \
+    { K30,    K31,    K32,    K33,    K34,    KC_NO,  KC_NO,  K37   }, \
+    { K38,    K39,    K3A,    KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO }, \
+    { KC_NO,  K41,    K42,    KC_NO,  KC_NO,  KC_NO,  K46,    K47   }, \
+    { K48,    KC_NO,  KC_NO,  KC_NO,  K4C,    K4D,    K4E,    KC_NO }, \
+    { KC_NO,  KC_NO,  K52,    K53,    K54,    K55,    K56,    K57   }, \
+    { K58,    K59,    KC_NO,  K5B,    K5C,    KC_NO,  KC_NO,  KC_NO }, \
+    { KC_NO,  KC_NO,  K62,    KC_NO,  KC_NO,  KC_NO,  K66,    KC_NO }, \
+    { K68,    KC_NO,  KC_NO,  KC_NO,  KC_NO,  K6D,    KC_NO,  KC_NO }, \
+}
+
+/* International keyboard layout for M0110 + M0120
+ * https://en.wikipedia.org/wiki/File:Apple_Macintosh_Plus_Keyboard.jpg
+ * Probably International keyboard layout of M0110A doesn't exist.
+ *
+ * M0110 + M0120 scan codes
+ * ,---------------------------------------------------------. ,---------------.
+ * | 32| 12| 13| 14| 15| 17| 16| 1A| 1C| 19| 1D| 1B| 18|   33| | 47| 68| 6D| 62|
+ * |---------------------------------------------------------| |---------------|
+ * |   30| 0C| 0D| 0E| 0F| 11| 10| 20| 22| 1F| 23| 21| 1E| 2A| | 59| 5B| 5C| 4E|
+ * |------------------------------------------------------,  | |---------------|
+ * |    39| 00| 01| 02| 03| 05| 04| 26| 28| 25| 29| 27| 24|  | | 56| 57| 58| 66|
+ * |---------------------------------------------------------| |---------------|
+ * |  38| 06| 07| 08| 09| 0B| 2D| 2E| 2B| 2F| 2C| 0A|      38| | 53| 54| 55|   |
+ * `---------------------------------------------------------' |-----------| 4C|
+ *      | 3A|  37|             34              |   31| 3A|     |     52| 41|   |
+ *      `------------------------------------------------'     `---------------'
+ * Two right and left keys of 38 and 3A are identical, you cannot discriminate those two.
+ */
+#define LAYOUT_iso( \
+    K32,K12,K13,K14,K15,K17,K16,K1A,K1C,K19,K1D,K1B,K18,K33,  K47,K68,K6D,K62, \
+    K30,K0C,K0D,K0E,K0F,K11,K10,K20,K22,K1F,K23,K21,K1E,K2A,  K59,K5B,K5C,K4E, \
+    K39,K00,K01,K02,K03,K05,K04,K26,K28,K25,K29,K27,K24,      K56,K57,K58,K66, \
+    K38,K06,K07,K08,K09,K0B,K2D,K2E,K2B,K2F,K2C,K0A,          K53,K54,K55,K4C, \
+        K3A,K37,            K34,                K31,          K52,    K41      \
+) { \
+    { K00,    K01,    K02,    K03,    K04,    K05,    K06,    K07   }, \
+    { K08,    K09,    K0A,    K0B,    K0C,    K0D,    K0E,    K0F   }, \
+    { K10,    K11,    K12,    K13,    K14,    K15,    K16,    K17   }, \
+    { K18,    K19,    K1A,    K1B,    K1C,    K1D,    K1E,    K1F   }, \
+    { K20,    K21,    K22,    K23,    K24,    K25,    K26,    K27   }, \
+    { K28,    K29,    K2A,    K2B,    K2C,    K2D,    K2E,    K2F   }, \
+    { K30,    K31,    K32,    K33,    K34,    KC_NO,  KC_NO,  K37   }, \
+    { K38,    K39,    K3A,    KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO }, \
+    { KC_NO,  K41,    KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  K47   }, \
+    { KC_NO,  KC_NO,  KC_NO,  KC_NO,  K4C,    KC_NO,  K4E,    KC_NO }, \
+    { KC_NO,  KC_NO,  K52,    K53,    K54,    K55,    K56,    K57   }, \
+    { K58,    K59,    KC_NO,  K5B,    K5C,    KC_NO,  KC_NO,  KC_NO }, \
+    { KC_NO,  KC_NO,  K62,    KC_NO,  KC_NO,  KC_NO,  K66,    KC_NO }, \
+    { K68,    KC_NO,  KC_NO,  KC_NO,  KC_NO,  K6D,    KC_NO,  KC_NO }, \
+}

keyboards/converter/m0110_usb/matrix.c

@@ -0,0 +1,121 @@
+/*
+Copyright 2011,2012 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+
+--------------
+
+Ported to QMK by Techsock <info@techsock.com>
+*/
+
+#include <stdint.h>
+#include <avr/io.h>
+#include <util/delay.h>
+#include "print.h"
+#include "util.h"
+#include "debug.h"
+#include "host.h"
+#include "m0110.h"
+#include "matrix.h"
+#include "report.h"
+#include "timer.h"
+
+
+#define CAPS        0x39
+#define CAPS_BREAK  (CAPS | 0x80)
+#define ROW(key)    ((key)>>3&0x0F)
+#define COL(key)    ((key)&0x07)
+
+
+static bool is_modified = false;
+
+// matrix state buffer(1:on, 0:off)
+static uint8_t *matrix;
+static uint8_t _matrix0[MATRIX_ROWS];
+
+static void register_key(uint8_t key);
+
+
+__attribute__ ((weak))
+void matrix_init_kb(void) {
+    matrix_init_user();
+}
+
+__attribute__ ((weak))
+void matrix_scan_kb(void) {
+    matrix_scan_user();
+}
+
+__attribute__ ((weak))
+void matrix_init_user(void) {
+}
+
+__attribute__ ((weak))
+void matrix_scan_user(void) {
+}
+
+void matrix_init(void)
+{
+    m0110_init();
+    // initialize matrix state: all keys off
+    for (uint8_t i=0; i < MATRIX_ROWS; i++) _matrix0[i] = 0x00;
+    matrix = _matrix0;
+
+	matrix_init_quantum();
+    return;
+}
+
+uint8_t matrix_scan(void)
+{
+    uint8_t key;
+
+    is_modified = false;
+    key = m0110_recv_key();
+
+    if (key == M0110_NULL) {
+        return 0;
+    } else if (key == M0110_ERROR) {
+        return 0;
+    } else {
+        is_modified = true;
+        register_key(key);
+    }
+
+    if (debug_enable) {
+        print("["); phex(key); print("]\n");
+    }
+    
+    matrix_scan_quantum();
+    return 1;
+}
+
+void matrix_print(void){
+
+}
+
+inline
+uint8_t matrix_get_row(uint8_t row)
+{
+    return matrix[row];
+}
+
+inline
+static void register_key(uint8_t key)
+{
+    if (key&0x80) {
+        matrix[ROW(key)] &= ~(1<<COL(key));
+    } else {
+        matrix[ROW(key)] |=  (1<<COL(key));
+    }
+}

keyboards/converter/m0110_usb/rules.mk

@@ -0,0 +1,73 @@
+# MCU name
+# atmega32u4 	Teensy2.0
+# atemga32u4	TMK Converter rev.1
+# atemga32u2	TMK Converter rev.2
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+#
+#F_CPU = 16000000
+F_CPU = 8000000
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+# Bootloader
+#     This definition is optional, and if your keyboard supports multiple bootloaders of
+#     different sizes, comment this out, and the correct address will be loaded 
+#     automatically (+60). See bootloader.mk for all options.
+BOOTLOADER = caterina
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096	for TMK Converter rev.1/rev.2
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+
+# Build Options
+#   comment out to disable the options.
+#
+BOOTMAGIC_ENABLE	= no			# Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE		= no			# Mouse keys(+4700)
+CONSOLE_ENABLE		= yes			# Console for debug(+400)
+COMMAND_ENABLE		= no  			# Commands for debug and configuration
+SLEEP_LED_ENABLE 	= no  			# Breathing sleep LED during USB suspend
+NKRO_ENABLE 		= no			# USB Nkey Rollover - not yet supported in LUFA
+EXTRAKEY_ENABLE		= yes	
+USB_HID_ENABLE 		= yes
+BACKLIGHT_ENABLE 	= no
+#BLUETOOTH 			= AdafruitBLE   # For Adafruit Feather 32U4 BLE support, uncomment this line
+
+CUSTOM_MATRIX = yes
+SRC = matrix.c \
+      m0110.c

keyboards/crkbd/keymaps/like_jis/config.h

@@ -0,0 +1,49 @@
+/*
+This is the c configuration file for the keymap
+
+Copyright 2012 Jun Wako <wakojun@gmail.com>
+Copyright 2015 Jack Humbert
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+/* Use I2C or Serial */
+
+#define USE_I2C
+#define USE_SERIAL
+//#define USE_MATRIX_I2C
+
+/* Select hand configuration */
+
+#define MASTER_LEFT
+// #define MASTER_RIGHT
+// #define EE_HANDS
+
+#define SSD1306OLED
+
+#define USE_SERIAL_PD2
+
+#define PREVENT_STUCK_MODIFIERS
+#define TAPPING_FORCE_HOLD
+#define TAPPING_TERM 150
+
+#undef RGBLED_NUM
+#define RGBLIGHT_ANIMATIONS
+#define RGBLED_NUM 27
+#define RGBLIGHT_LIMIT_VAL 120
+#define RGBLIGHT_HUE_STEP 10
+#define RGBLIGHT_SAT_STEP 17
+#define RGBLIGHT_VAL_STEP 17

keyboards/crkbd/keymaps/like_jis/glcdfont.c

@@ -0,0 +1,244 @@
+// This is the 'classic' fixed-space bitmap font for Adafruit_GFX since 1.0.
+// See gfxfont.h for newer custom bitmap font info.
+
+#ifndef FONT5X7_H
+#define FONT5X7_H
+
+#ifdef __AVR__
+ #include <avr/io.h>
+ #include <avr/pgmspace.h>
+#elif defined(ESP8266)
+ #include <pgmspace.h>
+#else
+ #define PROGMEM
+#endif
+
+// Standard ASCII 5x7 font
+
+static const unsigned char font[] PROGMEM = {
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x3E, 0x5B, 0x4F, 0x5B, 0x3E, 0x00,
+0x3E, 0x6B, 0x4F, 0x6B, 0x3E, 0x00,
+0x1C, 0x3E, 0x7C, 0x3E, 0x1C, 0x00,
+0x18, 0x3C, 0x7E, 0x3C, 0x18, 0x00,
+0x1C, 0x57, 0x7D, 0x57, 0x1C, 0x00,
+0x1C, 0x5E, 0x7F, 0x5E, 0x1C, 0x00,
+0x00, 0x18, 0x3C, 0x18, 0x00, 0x00,
+0xFF, 0xE7, 0xC3, 0xE7, 0xFF, 0x00,
+0x00, 0x18, 0x24, 0x18, 0x00, 0x00,
+0xFF, 0xE7, 0xDB, 0xE7, 0xFF, 0x00,
+0x30, 0x48, 0x3A, 0x06, 0x0E, 0x00,
+0x26, 0x29, 0x79, 0x29, 0x26, 0x00,
+0x40, 0x7F, 0x05, 0x05, 0x07, 0x00,
+0x40, 0x7F, 0x05, 0x25, 0x3F, 0x00,
+0x5A, 0x3C, 0xE7, 0x3C, 0x5A, 0x00,
+0x7F, 0x3E, 0x1C, 0x1C, 0x08, 0x00,
+0x08, 0x1C, 0x1C, 0x3E, 0x7F, 0x00,
+0x14, 0x22, 0x7F, 0x22, 0x14, 0x00,
+0x5F, 0x5F, 0x00, 0x5F, 0x5F, 0x00,
+0x06, 0x09, 0x7F, 0x01, 0x7F, 0x00,
+0x00, 0x66, 0x89, 0x95, 0x6A, 0x00,
+0x60, 0x60, 0x60, 0x60, 0x60, 0x00,
+0x94, 0xA2, 0xFF, 0xA2, 0x94, 0x00,
+0x08, 0x04, 0x7E, 0x04, 0x08, 0x00,
+0x10, 0x20, 0x7E, 0x20, 0x10, 0x00,
+0x08, 0x08, 0x2A, 0x1C, 0x08, 0x00,
+0x08, 0x1C, 0x2A, 0x08, 0x08, 0x00,
+0x1E, 0x10, 0x10, 0x10, 0x10, 0x00,
+0x0C, 0x1E, 0x0C, 0x1E, 0x0C, 0x00,
+0x30, 0x38, 0x3E, 0x38, 0x30, 0x00,
+0x06, 0x0E, 0x3E, 0x0E, 0x06, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x5F, 0x00, 0x00, 0x00,
+0x00, 0x07, 0x00, 0x07, 0x00, 0x00,
+0x14, 0x7F, 0x14, 0x7F, 0x14, 0x00,
+0x24, 0x2A, 0x7F, 0x2A, 0x12, 0x00,
+0x23, 0x13, 0x08, 0x64, 0x62, 0x00,
+0x36, 0x49, 0x56, 0x20, 0x50, 0x00,
+0x00, 0x08, 0x07, 0x03, 0x00, 0x00,
+0x00, 0x1C, 0x22, 0x41, 0x00, 0x00,
+0x00, 0x41, 0x22, 0x1C, 0x00, 0x00,
+0x2A, 0x1C, 0x7F, 0x1C, 0x2A, 0x00,
+0x08, 0x08, 0x3E, 0x08, 0x08, 0x00,
+0x00, 0x80, 0x70, 0x30, 0x00, 0x00,
+0x08, 0x08, 0x08, 0x08, 0x08, 0x00,
+0x00, 0x00, 0x60, 0x60, 0x00, 0x00,
+0x20, 0x10, 0x08, 0x04, 0x02, 0x00,
+0x3E, 0x51, 0x49, 0x45, 0x3E, 0x00,
+0x00, 0x42, 0x7F, 0x40, 0x00, 0x00,
+0x72, 0x49, 0x49, 0x49, 0x46, 0x00,
+0x21, 0x41, 0x49, 0x4D, 0x33, 0x00,
+0x18, 0x14, 0x12, 0x7F, 0x10, 0x00,
+0x27, 0x45, 0x45, 0x45, 0x39, 0x00,
+0x3C, 0x4A, 0x49, 0x49, 0x31, 0x00,
+0x41, 0x21, 0x11, 0x09, 0x07, 0x00,
+0x36, 0x49, 0x49, 0x49, 0x36, 0x00,
+0x46, 0x49, 0x49, 0x29, 0x1E, 0x00,
+0x00, 0x00, 0x14, 0x00, 0x00, 0x00,
+0x00, 0x40, 0x34, 0x00, 0x00, 0x00,
+0x00, 0x08, 0x14, 0x22, 0x41, 0x00,
+0x14, 0x14, 0x14, 0x14, 0x14, 0x00,
+0x00, 0x41, 0x22, 0x14, 0x08, 0x00,
+0x02, 0x01, 0x59, 0x09, 0x06, 0x00,
+0x3E, 0x41, 0x5D, 0x59, 0x4E, 0x00,
+0x7C, 0x12, 0x11, 0x12, 0x7C, 0x00,
+0x7F, 0x49, 0x49, 0x49, 0x36, 0x00,
+0x3E, 0x41, 0x41, 0x41, 0x22, 0x00,
+0x7F, 0x41, 0x41, 0x41, 0x3E, 0x00,
+0x7F, 0x49, 0x49, 0x49, 0x41, 0x00,
+0x7F, 0x09, 0x09, 0x09, 0x01, 0x00,
+0x3E, 0x41, 0x41, 0x51, 0x73, 0x00,
+0x7F, 0x08, 0x08, 0x08, 0x7F, 0x00,
+0x00, 0x41, 0x7F, 0x41, 0x00, 0x00,
+0x20, 0x40, 0x41, 0x3F, 0x01, 0x00,
+0x7F, 0x08, 0x14, 0x22, 0x41, 0x00,
+0x7F, 0x40, 0x40, 0x40, 0x40, 0x00,
+0x7F, 0x02, 0x1C, 0x02, 0x7F, 0x00,
+0x7F, 0x04, 0x08, 0x10, 0x7F, 0x00,
+0x3E, 0x41, 0x41, 0x41, 0x3E, 0x00,
+0x7F, 0x09, 0x09, 0x09, 0x06, 0x00,
+0x3E, 0x41, 0x51, 0x21, 0x5E, 0x00,
+0x7F, 0x09, 0x19, 0x29, 0x46, 0x00,
+0x26, 0x49, 0x49, 0x49, 0x32, 0x00,
+0x03, 0x01, 0x7F, 0x01, 0x03, 0x00,
+0x3F, 0x40, 0x40, 0x40, 0x3F, 0x00,
+0x1F, 0x20, 0x40, 0x20, 0x1F, 0x00,
+0x3F, 0x40, 0x38, 0x40, 0x3F, 0x00,
+0x63, 0x14, 0x08, 0x14, 0x63, 0x00,
+0x03, 0x04, 0x78, 0x04, 0x03, 0x00,
+0x61, 0x59, 0x49, 0x4D, 0x43, 0x00,
+0x00, 0x7F, 0x41, 0x41, 0x41, 0x00,
+0x02, 0x04, 0x08, 0x10, 0x20, 0x00,
+0x00, 0x41, 0x41, 0x41, 0x7F, 0x00,
+0x04, 0x02, 0x01, 0x02, 0x04, 0x00,
+0x40, 0x40, 0x40, 0x40, 0x40, 0x00,
+0x00, 0x03, 0x07, 0x08, 0x00, 0x00,
+0x20, 0x54, 0x54, 0x78, 0x40, 0x00,
+0x7F, 0x28, 0x44, 0x44, 0x38, 0x00,
+0x38, 0x44, 0x44, 0x44, 0x28, 0x00,
+0x38, 0x44, 0x44, 0x28, 0x7F, 0x00,
+0x38, 0x54, 0x54, 0x54, 0x18, 0x00,
+0x00, 0x08, 0x7E, 0x09, 0x02, 0x00,
+0x18, 0xA4, 0xA4, 0x9C, 0x78, 0x00,
+0x7F, 0x08, 0x04, 0x04, 0x78, 0x00,
+0x00, 0x44, 0x7D, 0x40, 0x00, 0x00,
+0x20, 0x40, 0x40, 0x3D, 0x00, 0x00,
+0x7F, 0x10, 0x28, 0x44, 0x00, 0x00,
+0x00, 0x41, 0x7F, 0x40, 0x00, 0x00,
+0x7C, 0x04, 0x78, 0x04, 0x78, 0x00,
+0x7C, 0x08, 0x04, 0x04, 0x78, 0x00,
+0x38, 0x44, 0x44, 0x44, 0x38, 0x00,
+0xFC, 0x18, 0x24, 0x24, 0x18, 0x00,
+0x18, 0x24, 0x24, 0x18, 0xFC, 0x00,
+0x7C, 0x08, 0x04, 0x04, 0x08, 0x00,
+0x48, 0x54, 0x54, 0x54, 0x24, 0x00,
+0x04, 0x04, 0x3F, 0x44, 0x24, 0x00,
+0x3C, 0x40, 0x40, 0x20, 0x7C, 0x00,
+0x1C, 0x20, 0x40, 0x20, 0x1C, 0x00,
+0x3C, 0x40, 0x30, 0x40, 0x3C, 0x00,
+0x44, 0x28, 0x10, 0x28, 0x44, 0x00,
+0x4C, 0x90, 0x90, 0x90, 0x7C, 0x00,
+0x44, 0x64, 0x54, 0x4C, 0x44, 0x00,
+0x00, 0x08, 0x36, 0x41, 0x00, 0x00,
+0x00, 0x00, 0x77, 0x00, 0x00, 0x00,
+0x00, 0x41, 0x36, 0x08, 0x00, 0x00,
+0x02, 0x01, 0x02, 0x04, 0x02, 0x00,
+0x3C, 0x26, 0x23, 0x26, 0x3C, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x0E, 0x3F, 0xFF, 0xFF,
+0xFF, 0xFF, 0xFE, 0xE0, 0x80, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x1E, 0xBE,
+0x7F, 0xFF, 0xFF, 0xFE, 0xFE, 0xF0,
+0xE0, 0xC0, 0x80, 0x00, 0x0E, 0xEF,
+0xDF, 0xDE, 0xBE, 0x3C, 0x38, 0x70,
+0xE0, 0xDD, 0xBB, 0x7B, 0x07, 0x0E,
+0x0E, 0x0C, 0x98, 0xF0, 0xE0, 0xF0,
+0xF0, 0xF8, 0x78, 0x3C, 0x1C, 0x1E,
+0x0E, 0x0E, 0x0F, 0x0F, 0x0F, 0x0F,
+0x1F, 0xFE, 0xFE, 0xF8, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0xE0, 0xF0, 0xF0, 0xF0, 0xE0, 0xEC,
+0xEE, 0xF7, 0xF3, 0x70, 0x20, 0x00,
+0x7C, 0x7C, 0x7C, 0x7E, 0x00, 0x7E,
+0x7E, 0x7E, 0x7F, 0x7F, 0x7F, 0x00,
+0x00, 0x80, 0xC0, 0xE0, 0x7E, 0x5B,
+0x4F, 0x5B, 0xFE, 0xC0, 0x00, 0x00,
+0xC0, 0x00, 0xDC, 0xD7, 0xDE, 0xDE,
+0xDE, 0xD7, 0xDC, 0x00, 0xC0, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x01, 0x03,
+0x0F, 0x3F, 0xFF, 0xFF, 0xFF, 0xFE,
+0xF8, 0xF0, 0xE0, 0xC0, 0x80, 0x7F,
+0xFF, 0xFE, 0xFD, 0xFB, 0x1B, 0x07,
+0x07, 0x0F, 0x1F, 0x1F, 0x1E, 0x1D,
+0x0B, 0x07, 0x01, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0xE0,
+0xF8, 0xFE, 0xFF, 0xFF, 0x1F, 0x07,
+0x01, 0x01, 0x01, 0x03, 0x06, 0x06,
+0x0C, 0x0C, 0x08, 0x0C, 0x0C, 0x0E,
+0x07, 0x83, 0xC1, 0xE0, 0x70, 0x30,
+0x18, 0x1C, 0x7C, 0xCC, 0x8C, 0xDC,
+0xF8, 0xC0, 0xE0, 0xE0, 0x70, 0xB8,
+0xF0, 0x60, 0x00, 0x00, 0x80, 0xC0,
+0xE0, 0xF0, 0x70, 0xF8, 0xFC, 0xFC,
+0x3C, 0x30, 0x38, 0xF8, 0xF8, 0xF8,
+0x78, 0x00, 0x80, 0x80, 0xC0, 0xE0,
+0x70, 0x38, 0x38, 0x9C, 0xDC, 0xFC,
+0x7C, 0x38, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x0F, 0x1F, 0x3F, 0x7F, 0x7F, 0x7F,
+0x7F, 0x7F, 0x3F, 0x1E, 0x0C, 0x00,
+0x1F, 0x1F, 0x1F, 0x3F, 0x00, 0x3F,
+0x3F, 0x3F, 0x7F, 0x7F, 0x7F, 0x00,
+0x30, 0x7B, 0x7F, 0x78, 0x30, 0x20,
+0x20, 0x30, 0x78, 0x7F, 0x3B, 0x00,
+0x03, 0x00, 0x0F, 0x7F, 0x0F, 0x0F,
+0x0F, 0x7F, 0x0F, 0x00, 0x03, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x01, 0x03, 0x07,
+0x1F, 0x3F, 0x3F, 0x7F, 0x7F, 0x7F,
+0x7E, 0x7D, 0x3B, 0x17, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x07,
+0x0F, 0x1F, 0x3F, 0x3F, 0x7E, 0x7C,
+0x78, 0x70, 0x70, 0x70, 0x70, 0x70,
+0x70, 0x78, 0x38, 0x18, 0x1C, 0x0E,
+0x07, 0x0F, 0x1F, 0x3F, 0x3C, 0x38,
+0x38, 0x18, 0x0C, 0x06, 0x03, 0x01,
+0x01, 0x01, 0x01, 0x0E, 0x1F, 0x1F,
+0x1C, 0x1C, 0x1E, 0x0F, 0x0F, 0x03,
+0x1D, 0x0E, 0x07, 0x03, 0x01, 0x00,
+0x00, 0x0E, 0x1F, 0x1F, 0x1D, 0x1E,
+0x0F, 0x07, 0x03, 0x03, 0x0F, 0x1F,
+0x1F, 0x19, 0x19, 0x19, 0x19, 0x0C,
+0x0C, 0x04, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+};
+#endif // FONT5X7_H

keyboards/crkbd/keymaps/like_jis/keymap.c

@@ -0,0 +1,229 @@
+#include QMK_KEYBOARD_H
+#include "bootloader.h"
+#ifdef PROTOCOL_LUFA
+  #include "lufa.h"
+  #include "split_util.h"
+#endif
+#ifdef SSD1306OLED
+  #include "ssd1306.h"
+#endif
+
+#include "../lib/mode_icon_reader.c"
+#include "../lib/layer_state_reader.c"
+#include "../lib/host_led_state_reader.c"
+#include "../lib/logo_reader.c"
+#include "../lib/keylogger.c"
+#include "../lib/timelogger.c"
+
+extern keymap_config_t keymap_config;
+
+#ifdef RGBLIGHT_ENABLE
+//Following line allows macro to read current RGB settings
+extern rgblight_config_t rgblight_config;
+#endif
+
+extern uint8_t is_master;
+
+// Each layer gets a name for readability, which is then used in the keymap matrix below.
+// The underscores don't mean anything - you can have a layer called STUFF or any other name.
+// Layer names don't all need to be of the same length, obviously, and you can also skip them
+// entirely and just use numbers.
+#define _QWERTY 0
+#define _LOWER 3
+#define _RAISE 4
+#define _ADJUST 16
+
+enum custom_keycodes {
+  LOWER = SAFE_RANGE,
+  RAISE,
+  ADJUST,
+  RGBRST
+};
+
+#define KC______ KC_TRNS
+#define KC_XXXXX KC_NO
+#define KC_KANJI KC_GRV
+
+#define KC_LOWER LOWER
+#define KC_RAISE RAISE
+
+#define KC_RST   RESET
+
+#define KC_LRST  RGBRST
+#define KC_LTOG  RGB_TOG
+#define KC_LHUI  RGB_HUI
+#define KC_LHUD  RGB_HUD
+#define KC_LSAI  RGB_SAI
+#define KC_LSAD  RGB_SAD
+#define KC_LVAI  RGB_VAI
+#define KC_LVAD  RGB_VAD
+#define KC_LSMOD RGB_SMOD
+
+#define KC_KNRM  AG_NORM
+#define KC_KSWP  AG_SWAP
+#define KC_GUAP  LALT_T(KC_APP)
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+  [_QWERTY] = LAYOUT_kc( \
+  //,-----------------------------------------.                ,-----------------------------------------.
+        ESC,     Q,     W,     E,     R,     T,                      Y,     U,     I,     O,     P,  MINS,\
+  //|------+------+------+------+------+------|                |------+------+------+------+------+------|
+       LSFT,     A,     S,     D,     F,     G,                      H,     J,     K,     L,    UP,   ENT,\
+  //|------+------+------+------+------+------|                |------+------+------+------+------+------|
+      LCTRL,     Z,     X,     C,     V,     B,                      N,     M,  COMM,  LEFT,  DOWN,  RGHT,\
+  //|------+------+------+------+------+------+------|  |------+------+------+------+------+------+------|
+                                   LGUI, LOWER,  BSPC,      SPC, RAISE,  GUAP \
+                              //`--------------------'  `--------------------'
+  ),
+
+  [_LOWER] = LAYOUT_kc( \
+  //,-----------------------------------------.                ,-----------------------------------------.
+        TAB,    F1,    F2,    F3,    F4,    F5,                  XXXXX,  MINS,   EQL,  JYEN,  LBRC,  RBRC,\
+  //|------+------+------+------+------+------|                |------+------+------+------+------+------|
+      _____,    F6,    F7,    F8,    F9,   F10,                  XXXXX, XXXXX, XXXXX,  SCLN,  QUOT,  BSLS,\
+  //|------+------+------+------+------+------|                |------+------+------+------+------+------|
+      _____,   F11,   F12, XXXXX, KANJI,   ENT,                  XXXXX, XXXXX,  COMM,   DOT,  SLSH,    RO,\
+  //|------+------+------+------+------+------+------|  |------+------+------+------+------+------+------|
+                                  _____, _____,   DEL,    XXXXX, _____,   APP \
+                              //`--------------------'  `--------------------'
+  ),
+
+  [_RAISE] = LAYOUT_kc( \
+  //,-----------------------------------------.                ,-----------------------------------------.
+      _____,     1,     2,     3,     4,     5,                      6,     7,     8,     9,     0, XXXXX,\
+  //|------+------+------+------+------+------|                |------+------+------+------+------+------|
+      _____, XXXXX, XXXXX, XXXXX, XXXXX, XXXXX,                  XXXXX,     4,     5,     6,  QUOT, XXXXX,\
+  //|------+------+------+------+------+------|                |------+------+------+------+------+------|
+      _____, XXXXX, XXXXX, XXXXX, XXXXX, XXXXX,                      0,     1,     2,     3,   DOT, XXXXX,\
+  //|------+------+------+------+------+------+------|  |------+------+------+------+------+------+------|
+                                  _____, _____, XXXXX,    XXXXX, _____,  LALT \
+                              //`--------------------'  `--------------------'
+  ),
+
+  [_ADJUST] = LAYOUT_kc( \
+  //,-----------------------------------------.                ,-----------------------------------------.
+        RST,  LRST,  KNRM,  KSWP, XXXXX, XXXXX,                  XXXXX, XXXXX, XXXXX, XXXXX, XXXXX, XXXXX,\
+  //|------+------+------+------+------+------|                |------+------+------+------+------+------|
+       LTOG,  LHUI,  LSAI,  LVAI, XXXXX, XXXXX,                  XXXXX, XXXXX, XXXXX, XXXXX,  PGUP, XXXXX,\
+  //|------+------+------+------+------+------|                |------+------+------+------+------+------|
+      LSMOD,  LHUD,  LSAD,  LVAD, XXXXX, XXXXX,                  XXXXX, XXXXX, XXXXX,  HOME,  PGDN,   END,\
+  //|------+------+------+------+------+------+------|  |------+------+------+------+------+------+------|
+                                  _____, _____, XXXXX,    XXXXX, _____, XXXXX \
+                              //`--------------------'  `--------------------'
+  )
+};
+
+int RGB_current_mode;
+
+// Setting ADJUST layer RGB back to default
+inline void update_tri_layer_RGB(uint8_t layer1, uint8_t layer2, uint8_t layer3) {
+  if (IS_LAYER_ON(layer1) && IS_LAYER_ON(layer2)) {
+    layer_on(layer3);
+  } else {
+    layer_off(layer3);
+  }
+}
+
+void matrix_init_user(void) {
+    #ifdef RGBLIGHT_ENABLE
+      RGB_current_mode = rgblight_config.mode;
+    #endif
+    //SSD1306 OLED init, make sure to add #define SSD1306OLED in config.h
+    #ifdef SSD1306OLED
+        iota_gfx_init(!has_usb());   // turns on the display
+    #endif
+}
+
+//SSD1306 OLED update loop, make sure to add #define SSD1306OLED in config.h
+#ifdef SSD1306OLED
+
+void matrix_scan_user(void) {
+   iota_gfx_task();
+}
+
+inline void matrix_render_user(struct CharacterMatrix *matrix) {
+  if (is_master) {
+    matrix_write_ln(matrix, read_layer_state());
+    matrix_write_ln(matrix, read_keylog());
+    matrix_write_ln(matrix, read_keylogs());
+    //matrix_write_ln(matrix, read_mode_icon(keymap_config.swap_lalt_lgui));
+    //matrix_write_ln(matrix, read_host_led_state());
+    //matrix_write_ln(matrix, read_timelog());
+  } else {
+    matrix_write(matrix, read_logo());
+  }
+}
+
+inline void matrix_update(struct CharacterMatrix *dest, const struct CharacterMatrix *source) {
+  if (memcmp(dest->display, source->display, sizeof(dest->display))) {
+    memcpy(dest->display, source->display, sizeof(dest->display));
+    dest->dirty = true;
+  }
+}
+
+void iota_gfx_task_user(void) {
+  struct CharacterMatrix matrix;
+  matrix_clear(&matrix);
+  matrix_render_user(&matrix);
+  matrix_update(&display, &matrix);
+}
+
+#endif
+
+bool process_record_user(uint16_t keycode, keyrecord_t *record) {
+  #ifdef SSD1306OLED
+    if (record->event.pressed) {
+      set_keylog(keycode, record);
+      set_timelog();
+    }
+  #endif
+
+  switch (keycode) {
+    case LOWER:
+      if (record->event.pressed) {
+        layer_on(_LOWER);
+        update_tri_layer_RGB(_LOWER, _RAISE, _ADJUST);
+      } else {
+        layer_off(_LOWER);
+        update_tri_layer_RGB(_LOWER, _RAISE, _ADJUST);
+      }
+      break;
+    case RAISE:
+      if (record->event.pressed) {
+        layer_on(_RAISE);
+        update_tri_layer_RGB(_LOWER, _RAISE, _ADJUST);
+      } else {
+        layer_off(_RAISE);
+        update_tri_layer_RGB(_LOWER, _RAISE, _ADJUST);
+      }
+      break;
+    case ADJUST:
+        if (record->event.pressed) {
+          layer_on(_ADJUST);
+        } else {
+          layer_off(_ADJUST);
+        }
+        break;
+
+    #ifdef RGBLIGHT_ENABLE
+    case RGB_MOD:
+        if (record->event.pressed) {
+          rgblight_mode(RGB_current_mode);
+          rgblight_step();
+          RGB_current_mode = rgblight_config.mode;
+        }
+      break;
+    case RGBRST:
+        if (record->event.pressed) {
+          eeconfig_update_rgblight_default();
+          rgblight_enable();
+          RGB_current_mode = rgblight_config.mode;
+        }
+      break;
+    #endif
+    default:
+      return true;
+  }
+
+  return false;
+}

keyboards/crkbd/keymaps/like_jis/rules.mk

@@ -0,0 +1,21 @@
+
+# Build Options
+#   change to "no" to disable the options, or define them in the Makefile in
+#   the appropriate keymap folder that will get included automatically
+#
+BOOTMAGIC_ENABLE = no       # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = no       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = no       # Audio control and System control(+450)
+CONSOLE_ENABLE = no         # Console for debug(+400)
+COMMAND_ENABLE = no        # Commands for debug and configuration
+NKRO_ENABLE = no            # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+BACKLIGHT_ENABLE = no      # Enable keyboard backlight functionality
+MIDI_ENABLE = no            # MIDI controls
+AUDIO_ENABLE = no           # Audio output on port C6
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+RGBLIGHT_ENABLE = yes        # Enable WS2812 RGB underlight.  Do not enable this with audio at the same time.
+SWAP_HANDS_ENABLE = no        # Enable one-hand typing
+
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no    # Breathing sleep LED during USB suspend

keyboards/dc01/arrow/arrow.c

@@ -0,0 +1,43 @@
+/* Copyright 2018 Yiancar
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include "arrow.h"
+
+void matrix_init_kb(void) {
+	// put your keyboard start-up code here
+	// runs once when the firmware starts up
+
+	matrix_init_user();
+}
+
+void matrix_scan_kb(void) {
+	// put your looping keyboard code here
+	// runs every cycle (a lot)
+
+	matrix_scan_user();
+}
+
+bool process_record_kb(uint16_t keycode, keyrecord_t *record) {
+	// put your per-action keyboard code here
+	// runs for every action, just before processing by the firmware
+
+	return process_record_user(keycode, record);
+}
+
+void led_set_kb(uint8_t usb_led) {
+	// put your keyboard LED indicator (ex: Caps Lock LED) toggling code here
+
+	led_set_user(usb_led);
+}

keyboards/dc01/arrow/arrow.h

@@ -0,0 +1,41 @@
+/* Copyright 2018 Yiancar
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#ifndef ARROW_H
+#define ARROW_H
+
+#include "quantum.h"
+
+#define XXX KC_NO
+
+// This a shortcut to help you visually see your layout.
+// The first section contains all of the arguments
+// The second converts the arguments into a two-dimensional array
+#define LAYOUT_all( \
+    K00, K01, K02, \
+    K10, K11, K12, \
+                   \
+         K31,      \
+    K40, K41, K42  \
+) \
+{ \
+    { K00, K01, K02 }, \
+    { K10, K11, K12 }, \
+    { XXX, XXX, XXX }, \
+    { XXX, K31, XXX }, \
+    { K40, K41, K42 }  \
+}
+
+#endif

keyboards/dc01/arrow/config.h

@@ -0,0 +1,151 @@
+/*
+Copyright 2018 Yiancar
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0xFEED
+#define PRODUCT_ID      0x1012
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    Mechboards
+#define PRODUCT         DC01 Arrow
+#define DESCRIPTION     Arrow cluster of DC01 keyboard
+
+/* key matrix size */
+#define MATRIX_ROWS 5
+#define MATRIX_COLS 3
+
+/*
+ * Keyboard Matrix Assignments
+ *
+ * Change this to how you wired your keyboard
+ * COLS: AVR pins used for columns, left to right
+ * ROWS: AVR pins used for rows, top to bottom
+ * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
+ *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
+ *
+*/
+#define MATRIX_ROW_PINS { B0, C7, C6, B6, B4 }
+#define MATRIX_COL_PINS { F0, B7, D2 }
+#define UNUSED_PINS
+
+/* COL2ROW, ROW2COL, or CUSTOM_MATRIX */
+#define DIODE_DIRECTION COL2ROW
+
+// #define BACKLIGHT_PIN B7
+// #define BACKLIGHT_BREATHING
+// #define BACKLIGHT_LEVELS 3
+
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCING_DELAY 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/* If defined, GRAVE_ESC will always act as ESC when CTRL is held.
+ * This is userful for the Windows task manager shortcut (ctrl+shift+esc).
+ */
+// #define GRAVE_ESC_CTRL_OVERRIDE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/* key combination for magic key command */
+#define IS_COMMAND() ( \
+    keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
+)
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+/*
+ * MIDI options
+ */
+
+/* Prevent use of disabled MIDI features in the keymap */
+//#define MIDI_ENABLE_STRICT 1
+
+/* enable basic MIDI features:
+   - MIDI notes can be sent when in Music mode is on
+*/
+//#define MIDI_BASIC
+
+/* enable advanced MIDI features:
+   - MIDI notes can be added to the keymap
+   - Octave shift and transpose
+   - Virtual sustain, portamento, and modulation wheel
+   - etc.
+*/
+//#define MIDI_ADVANCED
+
+/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
+//#define MIDI_TONE_KEYCODE_OCTAVES 1

keyboards/dc01/arrow/info.json

@@ -0,0 +1,12 @@
+{
+    "keyboard_name": "DC01 Arrow Cluster",
+    "url": "",
+    "maintainer": "qmk",
+    "width": 3,
+    "height": 5,
+    "layouts": {
+        "LAYOUT_all": {
+            "layout": [{"label":"Insert", "x":0, "y":0}, {"label":"Home", "x":1, "y":0}, {"label":"PgUp", "x":2, "y":0}, {"label":"Delete", "x":0, "y":1}, {"label":"End", "x":1, "y":1}, {"label":"PgDn", "x":2, "y":1}, {"label":"\u2191", "x":1, "y":3}, {"label":"\u2190", "x":0, "y":4}, {"label":"\u2193", "x":1, "y":4}, {"label":"\u2192", "x":2, "y":4}]
+        }
+    }
+}

keyboards/dc01/arrow/keymaps/default/keymap.c

@@ -0,0 +1,42 @@
+/* Copyright 2018 REPLACE_WITH_YOUR_NAME
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include QMK_KEYBOARD_H
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+[0] = LAYOUT_all( /* Base */
+    KC_INS,  KC_HOME,  KC_PGUP, \
+    KC_DEL,  KC_END,   KC_PGDN, \
+                                \
+             KC_UP,             \
+    KC_LEFT, KC_DOWN,  KC_RIGHT \
+),
+};
+
+void matrix_init_user(void) {
+
+}
+
+void matrix_scan_user(void) {
+
+}
+
+bool process_record_user(uint16_t keycode, keyrecord_t *record) {
+  return true;
+}
+
+void led_set_user(uint8_t usb_led) {
+
+}